Sylvania NB501SL9 User Manual

Blu-ray Disc Player

Owner’s Manual

NB501SL9

Playback Function Setup OthersIntroduction Connections

IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR VISIT OUR WEB SITE AT http://www.sylvania-ce.com

Blu-ray Disc Player

AUDIO IN

VIDEO

OUT

VIDEO

Quick Start Guide

Quick Start GuideQuick Start Guide

1. Connections

NB501SL9

Playable Discs and Files

This unit is compatible to play back the following discs / files.

Playable discs Logos

Blu-ray Disc

- BD-video (single / double layer)

- BD-RE ver.2.1 (single / double layer) (Recorded in BDMV format)

- BD-R (single / double layer) (Recorded in BDMV format) (Unclosed discs may not be played back.)

DVD-video

DVD+RW (single layer)

DVD+R (single / double layer)

DVD-RW (finalized discs only)

DVD-R (finalized discs only)

CD-DA (audio CD)

CD-RW

CD-R

Kodak Picture CD

DTS-CD

Playable files Logos

DVD, CD-RW/-R,

JPEG

Readable cards Playable files / data

SD Memory Card (8MB - 2GB)

SDHC Memory Card (4GB)

miniSD Card (8MB - 2GB)

microSD Card (8MB - 2GB)

For miniSD Card and microSD Card, the adapter is necessary.

•

“Blu-ray Disc“ and are trademarks.

is a trademark of DVD Format/Logo Licensing Corporation.

SD Memory Card (including SDHC), miniSD Card, microSD Card

JPEG, picture-in-picture commentary, subtitles or other extras for BD-ROM Profile 1 ver.1.1

miniSD Card adapter

miniSD Card

microSD Card adapter

microSD Card

All devices should be turned off and disconnected from the power outlet, when you make the connections.

Supplied cables used in this connection are as follows:

RCA audio cable (L/R) x 1

• RCA video cable x 1

•

Please purchase the rest of the necessary cables at your local store.

Basic Connections

Make one of the following connections, depending on the capabilities of your existing device.

AUDIO CONNECTION

audio cable

this unit

RCA

STANDARD

AUDIO

and

Method 1

RCA video cable

VIDEO OUTAUDIO OUT

STANDARD

PICTURE

VIDEO CONNECTION

Method 2

(Green)

(Blue)

(Red)

(Blue)

BETTER

PICTURE

COMPONENT

VIDEO IN

PB/CB

PR/CR

RCA component

video cable

or or

COMPONENT

VIDEO OUT

PR/CRY

PB/C

(Red)

(Green)

COMPONENT VIDEO OUT

Method 3

HDMI-DVI cable

HDMI OUT

HDMI Connection

AUDIO/VIDEO CONNECTION

BEST

AUDIO /

PICTURE

Method 4

this unit TV

HDMI IN

HDMI cable

DVI I N

BEST

PICTURE

Region Codes

This unit has been designed to play back BD-video with region A and DVD-video with region

BD-videoDVD-video

Press [HDMI] to change the resolution of the video signal being output from HDMI OUT jack. The video resolution changes as follows every time [HDMI] is pressed.

480p 720p 1080i 1080p 1080p24

“1” or “ALL“. You cannot play back BD-video or DVD-video that are labeled for other regions. Look for the symbols on the right on your BD-video or DVD-video. If these region symbols do not appear on your BD-video or DVD-video, you cannot play back the disc in this unit. The letter or number inside the globe refers to region of the world. A BD-video or DVD-video labeled for a specific region can only play back on the unit with the same region code.

Printed in China

EN EN

1VMN25654 / ★★★★★

E5H26UD

Note :

• You cannot select the video resolutions which are not supported by the connected TV.

• In order to get natural and high quality film reproduction of 24-frame film material, use an HDMI cable (High Speed HDMI Cable is recommended) and select “1080p24” if the connected TV is compatible with 1080p24 frame input.

Follow to the back side of this sheet.

Align the disc to the disc tray guide.

MODE

PAUS

REV

PLAYFWD

STO

Connection to an A udio System

2-Channel Analog Audio Connection

stereo system

audio

STANDARD

AUDIO

this unit

Supplied cables used in this connection are as follows:

• Please purchase the rest of the necessary cables at your

local store.

AUDIO IN

RCA audio cable

AUDIO

OUT

RCA audio cable (L/R) x 1

analog audio input jacks

POWER

EAR

DISPLAY

LEAR

REENBLUE YELL

ENTER

OPEN/

A-

2. Playback1. Connections (cont'd)

Press [POWER].

Turn on the TV and select the

appropriate input on the TV to which the unit is connected.

Press [OPEN / CLOSE A ] to open

the disc tray.

Place the disc on the disc tray with

its label side facing up.

AUDIO OUT

Digital Audio Connection

AV receiver/ampli er

audio

BETTER

AUDIO

this unit

DIGITAL OUT (COAXIAL)

Connecting the AC Cord

digital audio coaxial cable

DIGITAL AUDIO INPUT

COAXIAL

digital audio coaxial input jack

Supplied cables used in this connection are as follows:

AC cord x 1•

After you made all necessary connections, connect the AC cord to the AC IN. Then connect the AC cord to the AC outlet.

Insert the plugs securely. Incomplete connections will result in the generation of noise.

this unit

AC outlet

PAUS E

BTITL

AUDIO

PLAY

STOP

Press [OPEN / CLOSE A ] to close the disc tray.

It may take a while to load the disc.

Some discs may start playback automatically.

Press [PLAY B] to start playback.

For many of BD-video and DVD-video, a menu screen may appear.

In this case, use [K / L / s / B] to select the desired item, then press [ENTER].

To pause playback: Press [PAUSE F ]. To return to normal playback: Press [PLAY B ]. To stop playback: Press [STOP C ]. To eject the disc:

Press [OPEN / CLOSE A ] to open the disc tray, then remove the disc before turning off the unit.

AC 120V, 60 Hz

AC cord

EN EN

PRECAUTIONS

The model and serial numbers of this unit may be found on the cabinet. You should record and retain those numbers for future reference.

Model No.:

Serial No.:

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPARATUS TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The caution marking is located on the rear or bottom of the cabinet.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the apparatus’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus.

Important Safeguards

1. READ INSTRUCTIONS - All the safety and operating instructions should

be read before the apparatus is operated.

2. RETAIN INSTRUCTIONS - The safety and operating instructions should

be retained for future reference.

3. HEED WARNINGS - All warnings on the apparatus and in the operating

instructions should be adhered to.

4. FOLLOW INSTRUCTIONS - All operating and use instructions should be

followed.

5. CLEANING - Unplug this apparatus from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: An apparatus that is meant for uninterrupted service and,

that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the apparatus in the cleaning description otherwise required in item 5.

6. ATTACHMENTS - Do not use attachments not recommended by the

apparatus manufacturer as they may cause hazards.

7. WATER AND MOISTURE - Do not use this apparatus near water, for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. ACCESSORIES - Do not place this apparatus on an

unstable cart, stand, tripod, bracket, or table. The apparatus may fall, causing serious injury to someone, and serious damage to the apparatus. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the apparatus. Any mounting of the apparatus should follow the manufacturer’ s instructions and should use a mounting accessory recommended by the manufacturer. An apparatus and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the apparatus and cart combination to overturn.

9. VENTILATION - Slots and openings in the cabinet and the back or

bottom are provided for ventilation and to ensure reliable operation of the apparatus and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the apparatus on a bed, sofa, carpet, rug, or other similar surface. This apparatus should never be placed near or over a radiator or heat register. This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10. POWER SOURCES - This apparatus should be operated only from the

type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your apparatus dealer or local power company. For the apparatus’s intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION - This apparatus is equipped with a

polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. POWER-CORD PROTECTION - Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the apparatus.

13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or cable

system is connected to the apparatus, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

NEC – NATIONAL ELECTRICAL CODE

14. LIGHTNING - For added protection for this apparatus receiver during a

lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the apparatus due to lightning and power-line surges.

15. POWER LINES - An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. OVERLOADING - Do not overload wall outlets and extension cords as this

can result in a risk of fire or electric shock.

17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this

apparatus through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the apparatus.

18. SERVICING - Do not attempt to service this apparatus yourself as

opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. DAMAGE REQUIRING SERVICE - Unplug this apparatus from the wall

outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the apparatus. c. If the apparatus has been exposed to rain or water. d. If the apparatus does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified

technician to restore the apparatus to its normal operation. e. If the apparatus has been dropped or damaged in any way. f. When the apparatus exhibits a distinct change in performance, this

indicates a need for service.

20. REPLACEMENT PARTS - When replacement parts are required, be sure the

service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21. SAFETY CHECK - Upon completion of any service or repairs to this

apparatus, ask the service technician to perform routine safety checks to determine that the apparatus is in proper operating condition.

22. HEAT - This apparatus should be situated away from heat sources such as

radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

FIGURE A

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMP

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

ANTENNA LEAD WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMP

PRECAUTIONS

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the apparatus and receiver.

3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building as close to the point of cable entry as practical.

Introduction

Connections

Playback Function Setup Others

LASER SAFETY

This apparatus employs a laser. Only a qualified service person should remove the cover or attempt to service this apparatus, due to possible eye injury.

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may

CAUTION: Visible and invisible laser radiation when open and interlock defeated. Do not stare into beam. LOCATION: Inside, near the deck mechanism.

ABOUT COPYRIGHT

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

result in hazardous radiation exposure.

PRECAUTIONS

Supplied Accessories

remote control with batteries (AAx2) (NB804UD)

owner’s manual (EN/ES/FR) (1VMN25653 / 1VMN25655

/ 1VMN25657)

Owner’s Manual

RCA audio / video cables

(WPZ0102TM015 / WPZ0102LTE01)

quick start guide (EN/ES/FR) (1VMN25654 / 1VMN25656)

AC cord (WAV0162LW001)

To Avoid the Hazards of Electrical Shock and Fire

Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it

• from an AC outlet. Grasp it by the plug.

Do not put your fingers or objects into the unit.

•

Installation Location

For safety and optimum performance of this unit:

Install the unit in a horizontal and stable position. Do

• not place anything directly on top of the unit. Do not place the unit directly on top of the TV.

Shield it from direct sunlight and keep it away from

• devices of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the back and sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.

Be sure to remove the disc and unplug the AC power

• cord from the outlet before carrying the unit.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until its inside gets dry.

Note about Recycling

This unit’s packaging materials are recyclable

• and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or

• incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

Maintenance

Servicing

•

Please refer to relevant topics on “TROUBLESHOOTING” on page 43 before returning the product.

•

If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and please call our toll free customer support line found on the cover of this manual to locate an authorized service center.

Cleaning the cabinet

•

Wipe the front panel and other exterior surfaces of the unit with a soft, slightly damp cloth.

•

Never use a solvent, thinner, benzene or alcohol to clean the unit. Do not spray insecticide liquid near the unit. Such chemicals may discolor the surface or damage the unit.

Cleaning discs

•

When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.

•

Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analog records.

Cleaning the disc lens

•

If this unit still does not perform properly although you refer to the relevant sections and to “TROUBLESHOOTING” in this user manual, the laser optical pickup unit may be dirty. Consult your dealer or an authorized service center for inspection and cleaning of the laser optical pickup unit.

Disc handling

•

Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it is not used.

•

Note that discs with special shapes (heart-shaped discs, octagonal discs, etc.) cannot be played back on this unit. Do not attempt to playback such discs, as they may damage the unit.

IR signal check

If the remote control is not working properly, you can

• use an AM radio or digital camera (including a cellular phone with built-in camera) to see if it is sending out an infrared signal.

With an AM radio:

•

Tune the AM radio station to a nonbroadcasting frequency. Point the remote control towards it, push any button and listen. If the sound from the radio flutters, it is receiving the remote control’s infrared signal.

With a digital camera

• (including built-in cell phone cameras):

Point a digital camera towards the remote control. Push any button on the remote control and look through the digital camera. If the infrared light appears through the camera, the remote control is working.

PRECAUTIONS

Trademark Information

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

“Blu-ray Disc“ and

is a trademark of DVD Format/Logo Licensing

Corporation.

are trademarks.

Introduction

Connections

Java and all other Java trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and / or other countries.

Playback Function Setup Others

Product that have earned ENERGY STAR® are designed to protect the environment through superior energy efficiency.

is trademark of Eastman Kodak Company.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

CONTENTS

Introduction

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . .7

FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Front Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connections

CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connection to the TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connection to an Audio System . . . . . . . . . . . . . . . . . . . 15

Connecting the AC Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Playback

INFORMATION ON PLAYBACK . . . . . . . . . . . . . . . . . . . 17

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operations Using Title Menu, Disc Menu,

and Pop-up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Playing Back a VR mode DVD-RW/-R . . . . . . . . . . . . . . . 21

Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Playing Back an audio CD and a Disc with

JPEG Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Reading the SD Memory Card . . . . . . . . . . . . . . . . . . . . . 23

SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Fast Forward / Fast Reverse. . . . . . . . . . . . . . . . . . . . . . . . 25

Slow Forward Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Step by Step Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

A-B Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

PIP (Picture in Picture) Setting . . . . . . . . . . . . . . . . . . . . . 26

Program Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Camera Angle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SPECIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Switching Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Switching Audio Soundtrack . . . . . . . . . . . . . . . . . . . . . . 29

Setting the BD Audio Mode . . . . . . . . . . . . . . . . . . . . . . . 30

Adjusting the Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Function Setup

FUNCTION SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Others

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

LANGUAGE CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . Back Cover

FEATURES

Features

Full high-definition video playback

Watch movies in the highest picture quality available for your HDTV. This unit offers full high-definition video playback up to 1080p resolution for an amazing viewing experience. A highly detailed picture and increased sharpness delivers a more true-to-life picture.

HDMI

1080p / fps output (BD only)

This unit is equipped with the feature which can provide the smooth movement in the playback of film originated material with the frame rate of 24 frames per second with progressive. (Available only when the TV is connected by an HDMI cable and compatible with 1080p24 frame input.)

Refer to “HDMI Video Resolution” in “FUNCTION SETUP” on page 34.

Introduction

Connections

Upconvert DVD for enhanced picture quality

Your current DVD will look even better than before thanks to video upconversion. Upconversion will increase the resolution of standard definition DVD to high definition up to 1080p over an HDMI connection. The picture will be less jagged and more realistic for a near high-definition experience.

Enjoy your content on different kinds of media

Full backwards compatibility with DVD, CD ensures that you can continue to enjoy your current audio-video collection. Additionally, you can view JPEG.

Listen to the rich multi-channel surround sound

Multi-channel surround sound, which realizes real-to-life sound and makes you feel that you are really there.

Easy and simple connection to your HDTV via HDMI

Connect this unit to your HDTV with one single HDMI (high definition multimedia interface) cable. It is recommended to use High Speed HDMI Cable for better compatibility. The high definition video output signal will be transferred to your HDTV without conversion to analogue signals, so you will get an excellent picture and sound quality, completely free from noise.

Thanks to other multiple outputs, you can also easily connect to your home theater system or amplifier.

PIP

Some BD-video have the PIP (picture-in-picture) function which enables you to display the secondary video in the primary video. You can call up the secondary video by pressing [PIP] whenever the scene contains the secondary video.

Playing back the contents in SD Memory Card

You can play back JPEG stored in an SD Memory Card. You can store picture-in-picture commentary, subtitles or

other extras for BD-ROM Profile 1 ver.1.1 files in an SD Memory Card and play back with the BD-video.

Playback Function Setup Others

Symbols Used in this Manual

To specify for which media type each function is, we put the following symbols at the beginning of each item to operate.

Symbol Description

Description refers to BD-video and BD-RE (ver. 2.1) / BD-R recorded in BDMV format

Description refers to DVD-video

Description refers to DVD-RW/-R recorded in VR mode

Description refers to audio CD / DTS-CD

Description refers to DVD, CD-RW/-R and SD Memory Card with JPEG files

If you do not find any of the symbols listed above under the function heading, the operation is applicable to all media.

Pop-up menu

Some BD-video have pop-up menu which is a navigation menu that can be called up and be operated on the TV screen without interrupting the playback. You can call up the pop-up menu by pressing [POP MENU / MENU]. Contents in the pop-up menu vary depending on the disc.

HDMI Deep Color

Deep Color reduces the posterization effect of the playback image. Refer to “HDMI Deep Color” in “FUNCTION SETUP” on page 34.

Front Panel

FUNCTIONAL OVERVIEW

1 2* 3 4 5 6* 7 8 9

The unit can also be turned on by pressing these buttons.*

1. Disc tray

Place a disc when opening the disc tray.

•

2. A OPEN/CLOSE button*

Press to open or close the disc tray.

•

3. Display

Refer to “Front Panel Display” on page 11.

•

4. C STOP button

Press to stop playback.

•

5. k PAUSE button

Press to pause playback.

•

6. B PLAY button*

•

Press to start or resume playback.

Rear Panel

7. SD card slot

•

Insert an SD Memory Card, and play back the contents in it.

8. Infrared sensor window

•

Receive signals from your remote control so that you can control the unit from a distance.

9. POWER indicator

•

This indicator lights up in red when the power is on and turns off when the power is off.

yy POWER button

10.

Press to turn the unit on or off.

•

3 4 5

1. COMPONENT VIDEO OUT jacks

Use to connect a TV with component video inputs

• with an RCA component video cable.

2. HDMI OUT jack

Use to connect a TV with an HDMI compatible port

• with an HDMI cable.

3. AUDIO OUT jacks

Use to connect a TV, an AV receiver / amplifier or

• other device with an RCA audio cable.

4. DIGITAL OUT (COAXIAL) jack

Use to connect an AV receiver / amplifier, Dolby

• Digital / DTS decoder or other device with a digital audio coaxial input jack with a digital audio coaxial cable.

5. AC IN Terminal

•

Use to connect the AC outlet with the AC cord.

6. VIDEO OUT jack

•

Use to connect a TV, an AV receiver or other device with an RCA video cable.

Note

Do not touch the inner pins of the jacks on the rear

• panel. Electrostatic discharge may cause permanent damage to the unit.

This unit does not have the RF modulator.

•

FUNCTIONAL OVERVIEW

Remote Control

SKIP

15*

PIP

A-B

19 20

DISPLAY

OPEN/ CLOSE

HDMIPOWER

ANGLE

REPEAT

CLEAR

4 5

RED GREEN BLUE YELLOW

TOP MENU

POP MENU/

SETUP

ENTER

RETURN

AUDIO

MODEPAUS E

11*

SUBTITLE

REV PLAY FWD

SKIP STOP

* The unit can also be turned on by pressing these buttons.

1. DISPLAY button

Press to display the on-screen display menu.

•

2. POWER button

Press to turn the unit on or off.

•

3. Number buttons

Press to enter the title, chapter, track or file

• number. Press to enter values in the input field.

•

4. SEARCH button

Press to display the search menu.

•

5. RED / GREEN / BLUE / YELLOW button

Press to select items on some BD menus.

•

6. TOP MENU button

Press to display the top menu.

•

7. Cursor K / L / { / B buttons

Press to select items or settings.

•

8. SETUP button

Press to display the setup menu.

•

9. SUBTITLE button

Press to display the subtitle menu.

•

10. REV E button

During playback, press to fast reverse the playback.

•

11. PLAY B button*

•

Press to start playback or resume playback.

12. SKIP H button

•

During playback, press once to return to the beginning of the current title, chapter or track.

•

During the JPEG playback, press to return to the previous file.

•

During playback, press twice to return to the previous title, chapter or track.

13. PAUSE F button

•

Press to pause playback.

•

When playback is in pause mode, press repeatedly to forward the playback step by step.

14. HDMI button

•

Press to set the HDMI output mode.

15. OPEN/CLOSE A button*

•

Press to open or close the disc tray.

16. PIP button

•

Press to switch picture-in-picture feature on or off (only applicable to BD-video which supports the PIP function).

17. ANGLE button

•

Press to access various camera angles on the disc.

•

Press to rotate the JPEG files clockwise by 90 degrees.

18. REPEAT button

•

Press to toggle between various repeat modes.

19. A-B button

•

Press to play back a defined section between point A and B repeatedly.

20. CLEAR button

•

Press to clear the information once entered, to clear the marker settings, or to cancel the programming for audio CD, etc.

21. POP MENU/MENU button

Press to display the pop-up menu / disc menu / file list.

• Press to change “Original” and “Playlist” on the TV

• screen.

22. ENTER button

Press to confirm or select menu items.

•

23. RETURN

Press to return to the previously displayed menu

•

button

screen.

24. AUDIO button

Press to display the audio menu.

•

25. FWD D button

During playback, press to fast forward the

• playback. In pause mode, press to slow forward the playback.

•

26. STOP C button

Press to stop playback.

•

27. SKIP G button

During playback, press to skip to the next title,

• chapter, track or file.

28. MODE button

During playback, press to display the picture

• adjustment menu. During the JPEG playback, press to display menus

• for changing the visual effect for switching the image or changing the size of the image. In stop mode with BD inserted, press to display a

• menu for setting the BD audio mode. In stop mode with audio CD, or JPEG files inserted,

• press to display menus for program and random playback.

Introduction

Connections

Playback Function Setup Others

FUNCTIONAL OVERVIEW

Installing the Batteries in the Remote Control

Install the batteries (AAx2) matching the polarity indicated inside battery compartment of the remote control.

1 Open the cover.

2 Insert batteries.

Make sure to match + and - on the batteries to the marks indicated in the battery compartment.

3 Close the cover.

Using a Remote Control

Keep in mind the following when using the remote control:

Make sure that there are no obstacles between the

• remote control and the infrared sensor window on the unit.

Remote operation may become unreliable if strong

• sunlight or fluorescent light is shining on the infrared sensor window of the unit.

Remote control for different devices can interfere with

• each other. Avoid using remote control for other device located close to the unit.

•

Replace the batteries when you notice a fall off in the operating range of the remote control.

The maximum operable ranges from the unit are as

• follows.

Line of sight: approx. 23 feet (7m)

Either side of the center: approx. 16 feet (5m) within 30°

Above: approx. 16 feet (5m) within 15°

Below: approx. 10 feet (3m) within 30°

30˚30˚

16 feet

(5m)

23 feet

(7m)

16 feet

(5m)

Note

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

Do not mix new and old batteries together.

• Do not use different kinds of batteries together.

• Although they may look similar, different batteries may have different voltages.

Make sure that the + and - ends of each battery

• match the indications in the battery compartment.

Remove batteries from battery compartment that is

• not going to be used for a month or more.

When disposing of used batteries, please comply with

• governmental regulations or environmental public instruction’s rules that apply in your country or area.

Do not recharge, short-circuit, heat, burn or

• disassemble batteries.

FUNCTIONAL OVERVIEW

Front Panel Display

1 2

•

Brightness of the display can be adjusted. Refer to “Panel Display” in “FUNCTION SETUP” on page 41.

1. Displays playback status icon. Refer to the table below.

2. Displays various kinds of information such as title number, elapsed time, repeat mode, etc.

Playback status icon

Disc SD Memory Card

Playback is in progress

Stop mode

Pause mode

Mode

Introduction

Connections

Playback Function Setup Others

Example of Display Message

Fast forward mode

Fast reverse mode

Slow forward mode

Appears while repeat function is set

Title is being played back. Indicating the current title number and the elapsed time.

Current chapter is in chapter repeat mode.

Loading a disc.

Dolby Digital audio is being played back.

CONNECTIONS

Connection to the TV

Make one of the following connections, depending on the capabilities of your existing device.

•

AUDIO CONNECTION AUDIO / VIDEO

Method 1

standard audio

AUDIO IN

standard picture

VIDEO

RCA video

RCA

audio cable

and oror or

cable

this unit

VIDEO

OUT

VIDEO CONNECTION

Method 2

better picture

COMPONENT

VIDEO IN

(Green)

PB/CB

(Blue)

PR/CR

(Red)

RCA component video cable

COMPONENT

VIDEO OUT

PR/CRY

(Red)

(Blue)

(Green)

Method 3

best picture

HDMI-DVI cable

DVI IN

best audio / picture

CONNECTION

Method 4

HDMI IN

HDMI cable

1, 2

PB/C

AUDIO OUT HDMI OUTVIDEO OUT COMPONENT

VIDEO OUT

*1 This unit is compatible with the progressive scan system. The feature provides you with the higher quality pictures

than traditional output system does. To utilize this feature, a component or an HDMI connection is required. Refer to “HDMI Video Resolution” or “Component Output” setting on page 34 to set the video resolution.

Analog audio connection is not required for this connection.

Supplied cables used in this connection are as follows:

RCA audio cable (L/R) x 1

• RCA video cable x 1

•

Please purchase the rest of the necessary cables at your local store.

Note

Connect this unit directly to the TV. If the RCA audio / video cables are connected to a VCR, pictures may be

• distorted due to the copy-protection system.

If the picture is not output properly to the TV because of “HDMI Video Resolution” or “Component Output” setting,

• press and hold [ B PLAY] on the front panel for more than 5 seconds. “HDMI Video Resolution” and “Component Output” setting will be reset to the default automatically. You cannot change the video resolution during Blu-ray Disc playback. To change the resolution, stop playback.

A simple 1-cable connection with a device having an HDMI (high-definition multimedia interface) jack allows

• digital transfer of both digital video signals and multi-channel audio signals.

CONNECTIONS

HDMI Output Mode and Actual Output Signals

Press [HDMI] to change the resolution of the video signal being output from HDMI OUT jack. The video resolution changes as follows every time [HDMI] is pressed.

Front Panel

Display

Press [HDMI]

To play back the digital video images of a BD / DVD via an HDMI connection, it is necessary that both the unit and the TV (or an AV amplifier) support a copyright protection system called HDCP (high-bandwidth digital content protection system). HDCP is copy protection technology that comprises data encryption and authentication of the connected AV device. This unit supports HDCP. Please read the operating instructions of your TV (or AV amplifier) for more information.

HDMI Video Resolution

480 Progressive

720 Progressive

1080 Interlaced

1080 Progressive

1080 Progressive 24 24 frame

Connections

Playback Function Setup OthersIntroduction

Note

When using HDCP-incompatible TV, the image will not be viewed properly.

• Among the devices that support HDMI, some devices can control other devices via the HDMI jack, this unit cannot

• be controlled by another device via the HDMI jack.

The audio signals from HDMI OUT jack (including the sampling frequency, the number of channels and bit length)

• maybe limited by the device that is connected.

Among the devices that support HDMI, some do not support audio output (e.g, projectors). In connections with

• device such as this unit, audio signals are not output from HDMI OUT jack.

You cannot select the video resolutions which are not supported by the connected TV, except when this unit’s

• HDMI OUT jack is connected to a DVI compatible display devices with an HDMI-DVI cable.

For HDMI OUT jack to DVI connection, after you select an HDMI output mode, corresponding HDMI video

• resolution will be output. The HDMI video resolution you selected will be output even if the connected TV is not compatible with the HDMI video resolution. If there is no image displayed on the connected TV, please select another HDMI video resolution.

Video and audio signals may be distorted temporarily when switching to / from the HDMI output mode.

• You cannot change the video resolution during Blu-ray Disc playback. To change the resolution, stop playback.

• You can also change the HDMI output mode from “HDMI Video Resolution” setting in “Video” menu. In this menu,

• you can confirm what HDMI video resolutions are supported by connected TV. Refer to page 34.

In order to get natural and high quality film reproduction of 24-frame film material, use an HDMI cable (High

• Speed HDMI Cable is recommended) and select “1080p24” if the connected TV is compatible with 1080p24 frame input.

Even if you set “HDMI Video Resolution” setting to “1080p24”, when the contents of the disc is not compatible for

• 1080p24 frame, 1080p60 frame will be output.

There is no output from VIDEO OUT and COMPONENT VIDEO OUT jacks when you play back a BD that recorded

• 24-frame film material by HDMI output mode of 1080p24.

It is recommended to use High Speed HDMI Cable (also known as HDMI category 2 cable) for better compatibility.

•

CONNECTIONS

HDMI Audio Setting

When using HDMI connections make “HDMI Audio Out” setting in “Audio” menu according to the specifications of the device to be connected.

Device to be connected “HDMI Audio Out” setting Output HDMI audio signal

Device compatible with Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD decoding

Device compatible with 3 or more channels of audio inputs (not Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD compatible)

HDMI connection to a TV, and digital audio connection (coaxial) to an AV amplifier.

Audio signals output from HDMI OUT jack

■

Disc type Audio recording format

Dolby Digital Dolby Digital* Dolby Digital Plus Dolby Digital Plus*

BD-video

Dolby TrueHD Dolby TrueHD* DTS DTS* DTS-HD DTS-HD* LPCM Multi LPCM Multi LPCM

DVD-video / DVD-RW/-R

(VR mode)

Dolby Digital Dolby Digital Multi LPCM DTS DTS Multi LPCM LPCM Multi LPCM Multi LPCM

audio CD 2ch LPCM 2ch LPCM DTS-CD DTS Multi LPCM

HDMI Multi (Normal) Dolby Digital, Dolby Digital Plus, Dolby

TrueHD, DTS, or DTS-HD bitstream are output from HDMI OUT jack. Make the speaker settings on the connected AV amplifier, etc.

HDMI Multi (LPCM) Multi-channel audio signals are output

from HDMI OUT jack. Make the speaker settings with the speaker setting items appear after you select “HDMI Multi(LPCM)”. Refer to page 36.

Audio Mute HDMI audio will be muted, and Dolby

Digital / DTS bitstream or LPCM will be output from DIGITAL OUT jack depending on “Digital Out” setting. Refer to page 37.

“HDMI Audio Out” setting

HDMI Multi(Normal) HDMI Multi(LPCM)

Multi LPCM Multi LPCM* Multi LPCM* Multi LPCM Multi LPCM*

If “BD Audio Mode” setting is set to “Mix Audio Output”, audio will be output as multi LPCM. Refer to page 36.

Outputs audio signals decoded from independent substream.

Outputs audio signals decoded from Dolby Digital stream.

*4 Outputs audio signals decoded from DTS core stream.

•

If the connected device is not compatible with the HDMI BITSTREAM, audio will be output as multi LPCM or 2-channel down-mixed LPCM depending on the capability of the connected device even if you select “HDMI Multi(Normal)” in “HDMI Audio Out” setting. Refer to page 36.

CONNECTIONS

Connection to an Audio System

When you change the connections, all devices should be turned off.

• Refer to the manual accompanying external devices for more information.

•

2-Channel Analog Audio Connection

stereo system

AUDIO

OUT

AUDIO IN

audio

analog audio input jacks

RCA audio cable

this unit

Connections

Playback Function Setup OthersIntroduction

Digital Audio Connection

AV receiver / amplifier

audio

this unit

AUDIO OUT

DIGITAL AUDIO INPUT

digital audio coaxial

input jack

DIGITAL OUT (COAXIAL)

COAXIAL

digital audio coaxial cable

Supplied cables used in this connection are as follows:

RCA audio cable (L/R) x 1

• Please purchase the rest of the necessary cables at your local store.

CONNECTIONS

Audio signals output from DIGITAL OUT jack (COAXIAL)

■

The audio signals currently output from HDMI OUT jack will be output from DIGITAL OUT jack as well, except that Dolby Digital signal will be output instead of Dolby Digital Plus and Dolby TrueHD, and DTS signal will be output instead of DTS-HD.

When “Audio Mute” is selected in “HDMI Audio Out” setting, audio signals output from HDMI OUT jack will be muted and the audio signals output from DIGITAL OUT jack changes depending on “Digital Out” setting.

To set “Digital Out” setting, select “Audio Mute” in “HDMI Audio Out” setting.

Disc type Audio recording format

Dolby Digital Dolby Digital 2ch Downmix LPCM Dolby Digital Plus Dolby Digital 2ch Downmix LPCM

BD-video

DVD-video / DVD-RW/-R

(VR mode)

audio CD 2ch LPCM 2ch LPCM DTS-CD DTS 2ch Downmix LPCM

* For BD titles with secondary or interactive audio, these audio will be output as Dolby Digital when all the conditions

listed below are met:

•

When “BD Audio Mode” setting is set to “Mix Audio Output”.

•

When “HDMI Audio Out” setting is set to “Audio Mute”.

•

When “Digital Out” setting is set to “Bitstream”.

If BD titles do not have secondary or interactive audio, the audio will be output as shown in the table.

•

This table applies only when HDMI cable is not connected or “Audio Mute” is selected in “HDMI Audio Out” setting.

Dolby TrueHD Dolby Digital 2ch Downmix LPCM DTS DTS* 2ch Downmix LPCM DTS-HD DTS* 2ch Downmix LPCM LPCM 2ch Downmix LPCM* 2ch Downmix LPCM Dolby Digital Dolby Digital 2ch Downmix LPCM DTS DTS 2ch Downmix LPCM LPCM 2ch Downmix LPCM 2ch Downmix LPCM

Bitstream LPCM

“Digital Out” setting

Note

In order to output LPCM signal from DIGITAL OUT jack while outputting the HDMI audio signal, set “BD Audio

•

Mode” setting to “Mix Audio Output” and set “HDMI Audio Out” setting to “HDMI Multi(LPCM)”.

Connecting the AC Cord

After you made all necessary connections, connect the AC cord to the AC IN. Then connect the AC cord to the AC outlet.

Insert the plugs securely. Incomplete connections will result in the generation of noise.

this unit

AC cord

Supplied cables used in this connection are as follows:

AC cord x 1•

AC outlet

AC 120V, 60 Hz

INFORMATION ON PLAYBACK

Before you start playing back a disc, read the following information.

Playable Discs and Files

This unit is compatible to play back the following discs / files. To play back a disc / file, make sure that it meets the requirements for region codes and color systems as described below. You can play back discs that have the following logos. Other disc types are not guaranteed to play back.

Playable discs Logos

Blu-ray Disc

- BD-video (single / double layer)

- BD-RE ver.2.1 (single / double layer) (Recorded in BDMV format)

- BD-R (single / double layer) (Recorded in BDMV format) (Unclosed discs may not be played back.)

DVD-video

DVD+RW (single layer)

DVD+R (single / double layer)

Note for SD Memory Cards

Do not remove the SD Memory Card or turn off the

• unit while the contents of the card is in playback. It may result in malfunction or loss of the card’s data.

Please keep the SD Memory Cards in their cases

• when you are not using them. Do not try to open or modify the card.

• Do not touch the terminal surface with your fingers

• or any metals.

Do not attach additional labels or stickers to cards.

• Do not remove the label of the SD Memory Cards.

• This unit supports SD Memory Card with FAT12/

• FAT16 file system, and SDHC Memory Card with FAT32 file system.

This unit may not read the SD Memory Cards

• formatted on computer. If that is the case, please reformat the SD Memory Cards in this unit and try again.

This unit does not supports miniSDHC and

• microSDHC Memory Card.

For miniSD Card and microSD Card, the adapter is

• necessary.

Portions of this product are protected under

• copyright law and are provided under license by ARIS / SOLANA / 4C.

miniSD Card adapter

miniSD Card

microSD Card adapter

microSD Card

Introduction

Connections

Playback

Function Setup Others

DVD-RW (finalized discs only)

DVD-R (finalized discs only)

CD-DA (audio CD)

CD-RW

CD-R

Kodak Picture CD

DTS-CD

Playable files Media

DVD, CD-RW/-R,

JPEG

Readable cards Playable files / data

SD Memory Card (8MB - 2GB)

SDHC Memory Card (4GB)

miniSD Card (8MB - 2GB)

microSD Card (8MB - 2GB)

SD Memory Card (including SDHC), miniSD Card, microSD Card

JPEG, picture-in-picture commentary, subtitles or other extras for BD-ROM Profile 1 ver.1.1

Unplayable Discs and Files

The following discs will not be played back in this unit.

CD-ROM• CD-I (compact disc-interactive)• DVD-RAM• VSD (video single disc)• DVD-audio• BD-RE (ver.1 / ver.3)• HD DVD• video CD• unfinalized disc• SVCD• BD-RE/-R recorded in BDAV format• DVD / CD / SD Memory Card contains MP3,

• Windows Media™ Audio files and DivX®

super audio CD - Only the sound on the CD layer can

• be heard. The sound on the high-density super audio CD layer cannot be heard.

Playability of dual discs are not guaranteed.•

INFORMATION ON PLAYBACK

Color Systems

BD-video and DVD-video are recorded in different color systems throughout the world. The most common color system is NTSC (which is used primarily in the United States and Canada).

This unit employs NTSC color system, so the disc you play back must be recorded in the NTSC system. You cannot play back the disc recorded in other color systems.

Region Codes

BD-video

This unit has been designed to play back BD-video with region A and DVD-video with region “1” or “ALL“. You cannot play back BD-video or DVD-video that are labeled for other regions. Look for the symbols on the right on your BD-video or DVD-video. If these region symbols do not appear on your BD-video or DVD-video, you cannot play back the disc in this unit. The letter or number inside the globe refers to region of the world. A BD-video or DVD-video labeled for a specific region can only be played back in the unit with the same region code.

BD-video

DVD-video

Structure of Disc / SD Memory Card Contents

The contents of BD / DVD are generally divided into titles. Titles may be further subdivided into chapters.

title 1 title 2

chapter 1 chapter 2 chapter 1 chapter 2 chapter 3

BD / DVD

On-Screen Display

You can check information about the current disc by pressing [DISPLAY].

To call the on-screen display menu, press [DISPLAY] during playback. Every time you press [DISPLAY], the information changes. Depending on the media, available information varies.

off A Title / Chapter information

A Title information (elapsed time) A Title information (remaining time) A HDMI information A off

off A Chapter information (elapsed time) A Chapter information (remaining time) A Title information (elapsed time) A Title information (remaining time) A Bit rate information A HDMI information A off

off A Track information (elapsed time) A Track information (remaining time) A Disc information* (elapsed time) A Disc information* (remaining time) A HDMI information A off

(*not available during program / random playback)

audio CD are divided into tracks.

track 1 track 2 track 3 track 4 track 5

Data discs or SD Memory Cards containing JPEG are divided into folders, and the folders are subdivided into files.

folder (group) 1 folder (group) 2

group(folder)1 group(folder)2

le (track) 1 le (track) 2 le (track) 3 le (track) 4 le (track) 5

audio CD

JPEG

off A File name information A File information A HDMI information A off

For audio CD and JPEG, during program or random

• playback, the indication will be displayed after the track / file information.

Chapter information

■

1 3 42

INFORMATION ON PLAYBACK

Track / File information

■

1 3 42

Introduction

3 / 5 0 : 01 : 02

5 6

1 1 / 10 A B

Current chapter number / Total number of

chapters

Elapsed time / Remaining time of the current

chapter

Indicates that the multi camera angle images are

available on the scene

Current playback status

Current title number

Current repeat setting (Only when repeat setting

is active) (C: Chapter repeat, T: Title repeat, AB : A-B repeat)

■

Title information

1 2

3 / 5 0 : 01 : 02

Current title number / Total number of titles

Elapsed time / Remaining time of the current title

Bit rate information

■

Bit rate (The amount of video data currently being

ORG

read)

Layer number (Only for 2-layered discs)

(L0: Layer 0 is played back. L1: Layer 1 is played back)

Type of title (ORG: Original, PL: Playlist)

Current track (file) number / Total number of track

SD1 / 14 0 : 00: 51

(file)

Elapsed time / Remaining time of the current track

Indication of SD Memory Card playback

Current repeat setting

(Only when repeat setting is

active)

Connections

(T: Track / File repeat, G: Group repeat, A: All repeat, AB: A-B repeat)

■

Disc information

1 2

1 / 14 0 : 00: 51

Current track number / Total number of tracks

Elapsed time / Remaining time of the current disc

■

File name information

File_name_001

Media icon and file name

Playback

Function Setup Others

: JPEG file

■

HDMI information

HDMI video format

Resolution of the HDMI output image

HDMI audio format

Maximum numbers of audio channels that can be

Video Info Audio Info Max Channel

YCbCr PCM

2 ch

/ 1080i:

accepted by the connected device

Note

If the HDMI cable is not connected, “---” will be

• displayed for HDMI information.

MODE

PAUS

REV

PLAYFWD

STO

Playback

BASIC PLAYBACK

POWER

DISPLAY

EAR

REENBLUE YELL

BTITL

ENTER

PLAY

STOP

Press [POWER].

OPEN/

A-

LEAR

AUDIO

Turn on the TV and select the

appropriate input on the TV to which the unit is connected.

Press [OPEN / CLOSE A ] to open the

disc tray.

Place the disc on the disc tray with its

label side facing up.

Align the disc to the disc tray guide.

Press [OPEN / CLOSE A ] to close the

disc tray.

It may take a while to load the disc.

Some discs may start playback automatically.

Press [PLAY B] to start playback.

For many of BD-video and DVD-video, a menu screen may appear.

In this case, use [K / L / s / B] to select the desired item, then press [ENTER].

Press [STOP C ] once to stop

playback temporarily.

Refer to “Resume Playback” on page 21.

To eject the disc:

Press [OPEN / CLOSE A ] to open the disc tray, then remove the disc before turning off the unit.

Note

may appear at the top-right on the TV screen

• when the operation is prohibited by the disc or this unit.

During the playback of 2-layered disc, pictures may

• stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.

The operation may vary when you play back

• BD-video and DVD-video with disc menu. Refer to the manual accompanying the disc for details.

BASIC PLAYBACK

Operations Using Title Menu, Disc Menu, and Pop-up Menu

Many of BD-video and DVD-video disc contains title menu (BD-video / DVD-video), disc menu (DVD-video) or popup menu (BD-video) which guides you through the available functions in the disc. The contents of the menus may differ depending on the discs.

Title menu (BD-video / DVD-video)

1 Press [TOP MENU].

The title menu will appear.

•

2 Use [K / L / s / B] to select an item, then

press [ENTER].

3 Press [TOP MENU] to exit.

Disc menu (DVD-video)

1 Press [POP MENU / MENU].

The disc menu will appear.

•

2 Use [K / L / s / B] to select an item, then

press [ENTER].

3 Press [POP MENU / MENU] to exit.

Pop-up menu (BD-video)

This is a special feature available for some BD-video.

•

When you press [POP MENU / MENU], a menu pops out on the TV screen while the contents still play back.

1 During the playback of BD-video, press

[POP MENU / MENU].

The pop-up menu will appear.

•

2 Use [K / L / s / B] to select an item, then

press [ENTER].

3 Press [POP MENU/MENU] to exit.

Note

Contents of menus and corresponding menu

• operations may vary among discs. Refer to the manual accompanying the disc for details.

Playing Back a VR mode DVD-RW/-R

3 Use [K / L] to select a desired title, then

press [ENTER].

Note

“Original” is the title which is actually recorded on

• the disc.

“Playlist” is edited version of the “Original”.

• DVD menu varies depending on discs.

• If the disc does not contain “Playlist”, “Playlist” will

• not be displayed on the DVD menu.

Pause

1 During playback, press [PAUSE F ].

Playback will be paused.

•

2 Press [PLAY B ] to return to normal

playback.

Note

For BD and DVD, set “Still Mode” setting to “Field” in

• “Video” menu if pictures in the pause mode are blurred (refer to page 35).

Resume Playback

1 During playback, press [STOP C ].

Resume message will appear on the TV screen.

•

Resume ON

Press ‘PLAY’ to play from here. To play the beginning, press ‘STOP’ first and then ‘PLAY’.

e.g.) BD

2 Press [PLAY B ].

•

In a few seconds, playback will resume from the point at which it stopped last. To cancel the resume playback and start playback the disc from the beginning, press [STOP C ] again in stop mode.

Introduction

Connections

Playback

Function Setup Others

When you are playing back a VR mode DVD-RW/-R, you can choose “Original” or “Playlist” if the disc contains a “Playlist”.

1 In stop mode, press [POP MENU / MENU]

to call up the DVD menu.

2 Use [s / B] to select “Original” or “Playlist”.

Drama Series No.1 - No.3

PlaylistOriginal

1 08/ 1/ 8 PM10:00 1CH SLP 2 08/ 1/ 15 PM10:00 1CH SLP 3 08/ 1/ 22 PM10:00 1CH SLP

1/ 1

Note

Resume playback may not be available for the BD

• that supports Java applications (BD-Java).

The resume information will be saved even when the

• power is turned off.

If you open the disc tray or press [STOP C ] again in

• stop mode, the resume information will be cleared.

If you switch between “Disc” mode and “SD Memory”

• mode, the resume information will be cleared.

If you change “BD Rating Level” or “DVD Rating

• Level” setting in “

information will be cleared. For SD Memory Card, if you open the disc tray or

• turned off the power, resume information will be cleared.

Parental” menu, the resume

BASIC PLAYBACK

Playing Back an audio CD and a Disc with JPEG Files

Insert an audio CD or a disc with JPEG

files.

•

The file list will appear on the TV screen.

•

If file list does not appear automatically, press [POP MENU / MENU].

•

Press [POP MENU / MENU] to exit and resume the file list.

Use [K / L] to select a desired folder

or file, then press [ENTER]. Use [ s / B ] to go back and forward between the hierarchies.

If you press [ENTER] on the desired file,

• playback will start.

File List

JPEG_DISC

Folder_1

Folder_2 Folder_3 JPEG_A JPEG_B JPEG_C JPEG_D

Folder_1

4 5

2 / 4

It is recommended that files to be played back in this unit are recorded under the following specifications:

<JPEG>

Upper limit: 2,560 x 1,900 dots

•

Lower limit: 32 x 32 dots

• File size of image maximum: 12 MB

•

(sub sampling is 4:4:4) 5,120 x 3,840 dots (sub sampling is up to 4:2:2)

Note

The system can recognize up to 255 folders / 999 files

•

for CD, 999 folders / 9999 files for DVD and SD Memory Card.

The name of folder and file can be displayed up to 28

•

characters. Unrecognizable characters will be replaced with asterisks.

The 9th and deeper hierarchies cannot be displayed

•

for CD and the 10th and deeper hierarchies cannot be displayed for DVD and SD Memory Card.

Files whose extension is other than “.jpg / .jpeg(JPEG)”

•

will not be listed. Some unplayable folders or files may be listed due to

•

the recording status. High-resolution JPEG files take longer to be displayed.

•

Progressive JPEG files (JPEG files saved in progressive

•

format) cannot be played back in this unit. This unit recognize up to 8 characters of file name in

•

the SD Memory Card. Characters after 9th will not be displayed.

For the SD Memory Card playback, refer to “Reading

•

the SD Memory Card” on pages 23-24.

e.g.) JPEG

audio CD: “CD-DA” will be displayed.

JPEG: Current folder name (Disc or SD

audio CD: List of the track number and time.

JPEG: List of the file / folder names in the

audio CD: Selected track number and time.

JPEG: Selected file / folder name

Current page / Total page number

Indication of previous / next page

•

Use [SKIP H / G ] to go back and forward between the pages.

•

Press [TOP MENU] to return to the first item.

Icons:

: Folder

: audio CD track

: JPEG file

Memory Card name will be displayed for the top of the hierarchies.)

current folder / disc

BASIC PLAYBACK

Kodak Picture CD

This unit can also run JPEG files stored on Kodak Picture CD. You can enjoy picture images on the TV set by playing back the Kodak Picture CD. This unit confirms to ver.7.0 of Kodak Picture CD. For details of Kodak Picture CD, contact a shop that provides developing service of Kodak Inc.

When Kodak Picture CD is inserted in

this unit, Kodak Picture CD menu will appear automatically on the TV screen.

Photo A Photo B Photo C

Photo D Photo E Photo F

7 / 32HG

12 2

1. Current track number / The total number of tracks

2. Indication of previous / next page

•

In stop mode, press [POP MENU / MENU] to call Kodak Picture CD menu.

Use [K / L / s / K] to select a desired

track to be played back, then press [PLAY B ] or [ENTER].

•

An image will be played back from the selected track and go to the next one in turn.

•

Use [SKIP H / G ] to go back and forward between the pages.

Reading the SD Memory Card

You can play back the JPEG files in an SD Memory Card. With the SD Memory Card, you can also enjoy the special additional contents for BD-ROM Profile 1 ver.1.1 which can be downloaded from the internet. You can store the contents on an SD Memory Card via computer and play them back with the BD-video. For more information about the special additional contents, please refer to the instruction book that came with the disc.

■

Setting the media mode

In stop mode, press [SETUP].

Use [ K / L ] to select

[ENTER].

Custom

Language Video Audio Parental Others

Use [ K / L ] to select

[ENTER].

, then press

Introduction

Connections

Playback

Function Setup Others

Press [STOP C] to stop playback.

Tips for JPEG / Kodak Picture CD Playback

Every press on [ANGLE] will turn the image clockwise

• by 90 degrees when an image is displayed.

To change the visual effect for switching the playback

• image, press [MODE] once, then use [s / B] or [ENTER] to switch between “Cut In/Out” and “Fade In/ Out”. The size change may have no effect on some files (e.g. files with a small picture size).

During JPEG / Kodak Picture CD playback, press

• [MODE] twice to change the size of the playback image, then use [ s / B] or [ENTER] to switch between “Normal” (100%) and “Small” (95%). The size change may have no effect on some files (e.g. files with a small picture size).

Others

Angle Icon Auto Power Off Panel Display Slide Show Media Select

On On Auto 5sec Disc

Use [ K / L ] to select “Media Select”

setting.

BASIC PLAYBACK

Press [ENTER] repeatedly to select

“SD Memory”.

Others

Angle Icon Auto Power Off Panel Display Slide Show

Media Select

This will set the unit to “SD Memory” mode. To

• play back the contents in any discs, exit “SD Memory” mode by selecting “Disc”.

Press [SETUP] to exit.

On On Auto 5sec

SD Memory

Inserting the SD Memory Card and playback

Insert an SD Memory Card into the

Removing the SD Memory Card

1 2

SD card slot until it clicks with the label facing up.

The file list will appear.

SD Memory Card

Follow the step 2 in “Playing Back an

audio CD and a Disc with JPEG Files” on page 22.

In stop mode, push the SD Memory

Card and then slowly remove your finger.

Grasp the card and pull it out from

the SD card slot.

Compatible Cards:

- SD Memory Card (8MB - 2GB)

- SDHC Memory Card (4GB)

- miniSD Card (8MB - 2GB)

- microSD Card (8MB - 2GB)

•

For miniSD Card and microSD Card, the adapter will be required.

Note

Do not remove the card during its playback.

• This unit supports SD Memory Card with FAT12 /

• FAT16 file system, and SDHC Memory Card with FAT32 file system.

Do not delete the folders or files in the SD Memory

• Card with your computer. This unit might not read the SD Memory Card.

This unit recognize up to 8 characters of file name in

• the SD Memory Card. Characters after 9th will not be displayed.

SPECIAL PLAYBACK

Fast Forward / Fast Reverse

1 During playback, press [FWD D]

repeatedly for fast forward.

During playback, press [REV E] repeatedly for fast reverse.

Every time you press [FWD D] or [REV E], the playback speed will change.

2 Press [PLAY B] to return to normal

playback.

Note

For BD and DVD, the approximate speed for the fast

• forward or reverse playback is 1 (2x), 2(8x), 3 (20x), 4 (50x), and 5 (100x).

For audio CD, the approximate speed is 1 (2x), 2 (8x),

• and 3 (30x).

For audio CD, fast forward / fast reverse search

• between different tracks are not available during program and random playback.

Slow Forward Playback

1 During playback, press [PAUSE F], then

press [FWD D].

Every time you press [FWD D], playback speed will change.

2 Press [PLAY B] to return to normal

playback.

Note

The approximate speed for the slow forward

• playback is 1(1/16x), 2(1/8x), 3(1/2x).

Only slow forward is available.

• Set “Still Mode” setting to “Field” in “Video” menu if

• pictures in the slow forward playback mode are blurred (refer to page 35).

Step by Step Playback

1 In pause mode, press [PAUSE F]

repeatedly.

Every time you press [PAUSE F], playback will advance one step at a time.

2 Press [PLAY B] to return to normal

playback.

Note

Only step by step forward is available.

• Set “Still Mode” setting to “Field” in “Video” menu if

• pictures in step by step playback mode are blurred (refer to page 35).

Repeat Playback

Available repeat functions vary depending the discs.

1 During playback, press [REPEAT]

repeatedly to select the desired repeat mode.

Repeat mode Available media

Chapter repeat

The current chapter will be played back repeatedly.

Title repeat

The current title will be played back repeatedly.

Track repeat

The current track or file will be played back repeatedly.

Group repeat

The current folder will be played back repeatedly.

All repeat

All tracks in the media will be played back repeatedly.

Introduction

Connections

Playback

Function Setup Others

Note

The repeat setting will be canceled when you stop

• playback.

The chapter, title, track or group repeat will be

• cleared when moving to other chapter, title, track / file or folder.

Repeat playback does not function during A-B repeat

• playback.

Chapter and title repeat are not available with some

• scenes.

SPECIAL PLAYBACK

A-B Repeat

You can play back the specific part (between point A and point B) repeatedly.

1 During playback, press [A-B] at the

desired starting point A.

2 During playback, press [A-B] at the

desired ending point B.

As soon as you set the point B, the part between point A and point B will start playback repeatedly.

•

To cancel the A-B repeat, press [A-B] again.

Note

Point B should be set within the same title or track as

• point A.

A-B repeat is not available with some scenes.

• To cancel the A point which was set, press [CLEAR].

• A-B repeat does not function during chapter, title,

• track, group or all repeat playback.

PIP (Picture in Picture) Setting

primary

video

Program Playback

You can play back the disc in your desired order.

1 In stop mode, press [MODE].

The program screen will appear.

•

2 Use [K / L] to select a track / file, then

press [ENTER].

Program

CD-DA Total 0:09:49

3:40

2:33

2:22

2:28

2:45

3:41

2:58

1 / 3

6 3:41

e.g.) audio CD

•

For JPEG files, use [K / L] to select a folder, then press [ENTER] first, and then use [K / L] to select a file, then press [ENTER].

•

Press [CLEAR] to erase the last file of the program.

•

Use [K / L] to select “All Clear” at the bottom of the list to erase all the tracks / files in the program.

•

The programmed tracks / files is displayed in the right hand screen.

•

If the entire program cannot be displayed on the TV screen, “L” or “K” appears.

•

Use [s / B] to go back forward between the hierarchy of folders.

•

If 8 or more tracks / files were set in a program, use [SKIP H / G ] to see all the tracks / files.

3:40

2:28

3:41

1 / 1

3 Press [PLAY B ] to start program

playback.

Program playback will start.

•

secondary

video

1 During playback, press [PIP].

PIP information will appear.

2 Use [K / L] to select the secondary video

you want.

The secondary video will be displayed and the

• secondary audio will be output.

3 Press [RETURN ] or [PIP] to remove the

PIP information.

Note

The the secondary audio will not be output when the

• secondary audio is set to “Off” or when “BD Audio Mode” is set to “HD Audio Output”. Refer to “Switching Audio Soundtrack” on page 29 and “Setting the BD Audio Mode” on page 30.

Note

During program playback, press [STOP C ] once to

•

set the resume point, and then press [PLAY B ] to resume program playback from where [STOP C ] was pressed (audio CD) or from beginning of the file where [STOP C ] was pressed (JPEG).

During program playback, press [STOP C ] twice to

• display the program screen. To go back to the normal program playback, press [RETURN from the program screen, then press [PLAY B ].

•

If you open the disc tray, remove the SD Memory Card or turned off the power, the program will be cleared.

•

Up to 99 tracks / files can be entered.

•

To repeat the current track / file in the program, press [REPEAT] repeatedly until “ appears during play back. To repeat the entire program, press [REPEAT] repeatedly until “ appears during playback. Playback from a desired track / file and random

• playback are not available during program playback.

] to exit

Track”

All”

SPECIAL PLAYBACK

Random Playback

This function shuffles the playback order of tracks / files.

1 In stop mode, press [MODE] twice.

The random screen will appear.

•

Random

CD-DA Total 0:41:06

Random Program

-- no indication --

e.g.) audio CD

2 Press [PLAY B ] to start random

playback.

Note

During the random playback, press [STOP C ] once

•

to set the resume point, and then press [PLAY B ] to resume random playback from where [STOP C ] was pressed (audio CD) or from beginning of the file where [STOP C ] was pressed (JPEG).

During random playback, press [STOP C ] twice to

• display the random playback screen. To cancel the random playback, press [MODE] when the random playback screen is displayed.

To repeat the current track / file in the random

• selection, press [REPEAT] repeatedly until “ Track” appears during playback. To repeat the entire random selection press [REPEAT] repeatedly until “

All” appears during playback.

•

You cannot go back to the previous track / file during random playback.

Camera Angle

Some BD-video and DVD-video contain scenes which have been shot simultaneously from various angles. You

can change the camera angle when screen.

appears on the TV

1 During playback, press [ANGLE].

The selected angle will be displayed on the display

• bar at the top of the TV screen.

2 Use [K / L] to select your desired angle.

1 / 3

Note

If “Angle Icon” setting is “Off” in “Others” menu,

• will not appear. Refer to page 41.

Introduction

Connections

Playback

Function Setup Others

Using [SKIP H / G ]

1 During playback, press [SKIP G] to

move to the next track. Press it repeatedly to skip to subsequent tracks. Press [SKIP H ] once to go back to the beginning of the current track. Press it repeatedly to go to the previous tracks.

For JPEG files, press [SKIP H ] to go back to the

• previous file.

Note

For BD and DVD, if title contains no chapters,

•

[SKIP H / G ] changes the title. For JPEG files, [ s / B ] is also available.

•

Using [SEARCH]

By using [SEARCH], you can select following search modes.

Search mode Available media

Chapter / Title search

Track search

Time search

Marker search

1 During playback, press [SEARCH]

repeatedly until your desired search mode appears.

2 Enter the desired chapter, title, track, file

number or time to search for using [the Number buttons].

Chapter, title, track or time search will start.

• Press [CLEAR] to erase an incorrect input.

•

Marker search

■

This feature allows you to assign a specific point on a title or track to be called back later.

1 During playback, press [SEARCH]

repeatedly until the marker setting menu appears.

2 Use [s / B] to select a marker number

(1-9).

___ __ : __ :__

3 When the disc reaches the point at which

you want to set a marker, press [ENTER].

The title or track and elapsed playback time will

• appear on the TV screen.

4 Press [SEARCH] or [RETURN ] to exit. 5 To return to the marker later, call the

marker setting by pressing [SEARCH] repeatedly during playback or in stop mode, and use [s / B] to select a desired marker, then press [ENTER].

Note

•

Opening the disc tray, turning off the power or selecting “ erase all markers.

•

To clear a marker, use [s / B] to select the marker number to be cleared and press [CLEAR].

•

You can mark up to 9 points. For BD, marker search between different titles is not

• available.

For BD, you can return to the maker only during

• playback.

” at step 2 and pressing [ENTER] will

Note

During program and random playback, search

• functions are not available except the search using [SKIP H / G ].

Time search is available only in the same track, file or

• title.

For BD, chapter and time search are available only

• during playback.

+ 118 hidden pages