Sylvania 6615LCT User Manual

Owner’s Manual

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

GROUND
CLAMP

NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING

ELECTRODE SYSTEM
(NEC ART 250, PART H)

S2898A

GROUND CLAMPS

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

ANTENNA
LEAD IN
WIRE

6615LCT

15 INCH LCD TELEVISION
(Photo Stand Type)

FEATURES

●

MTS/SAP Tuner

●

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

●

PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets
you tune directly to any channel using the channel number buttons on the remote control.

●

Sleep Timer

●

Closed Caption Decoder

●

Auto Shut Off Function- If there is no signal input from the antenna terminal and no user
operation for 15 minutes, the TV will turn itself off automatically.

●

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

●

Full-Function Remote Control

●

On-Screen Function Display

●

S-VIDEO Input- Allows you to get better picture detail and clarity.

●

Component Input

PRECAUTIONS

●

Place your TV in a room with adequate ventilation.

●

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

●

Do not place your TV on soft surfaces, such as rugs or blankets.

●

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same
serial number as yours. You should record the number and other vital information here and retain
this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase
Dealer Purchase from
Dealer Address

IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE
VISIT OUR WEB SITE AT

http://www.SylvaniaConsumerElectronics.com

Dealer Phone No.
Model No.
Serial No.

1-800-968-3429 OR

SYLVANIA

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PAR TS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT
OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE
PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or

if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not
purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does
not cover damage which occurs in shipment, failures which are caused by repairs, alterations or product not supplied
by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration,
faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage
which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN
THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE
CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SER­VICE CENTER.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT.
IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS
COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT
VA RY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE
TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR
NOTICE.

WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:

To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service providers without prior written approval.

To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please contact us at :

1EMN21764 Printed in China

the date of original retail purchase. Certain parts and LCD image burn-in are not covered under
this warranty.

of original retail purchase.

FUNAI CORPORATION

Customer Service

Tel :[phone]

http://www.SylvaniaConsumerElectronics.com

19900 Van Ness Avenue, Torrance, CA 90501

L2500UA * * * * *

IMPORTANT SAFEGUARDS

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

SHOCK, DO NOT REMOVE COVER (OR BACK) NO
USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

The important note is located on the rear of the cabinet.

1. READ INSTRUCTIONS - All the safety and operat-

ing instructions should be read before the appliance is
operated.

2. RETAIN INSTRUCTIONS - The safety and operat-

ing instructions should be retained for future reference.

3. HEED WARNINGS - All warnings on the appliance

and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS - All operating and use

instructions should be followed.

5. CLEANING - Unplug TV from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as
the possibility of the loss of an authorization code for a
CATV converter, is not intended to be unplugged by the
user for cleaning or any other purpose, may exclude the
reference to unplugging the appliance in the cleaning
description otherwise required in item 5.

6. ATTACHMENTS - Do not use attachments not rec-

ommended by the TV manufacturer as they may cause
hazards.

7. WATER AND MOISTURE - Do not use this TV near

water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.

8. ACCESSORIES - Do not place this

TV on an unstable cart, stand, tripod,
bracket, or table. The TV may fall,
causing serious injury to someone, and
serious damage to the appliance. Use
only with a cart, stand, tripod, bracket,
or table recommended by the manufac­turer, or sold with the TV.
Any mounting of the appliance should follow the man­ufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer. An appli­ance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.

: TO REDUCE THE RISK OF ELECTRIC

PORTABLE CART WARNING

S3126A

9. VENTILATION - Slots and openings in the cabinet

10.

11.

12. POWER-CORD PROTECTION - Power-supply

THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUT­ING A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT OPERAT­ING AND MAINTENANCE INSTRUC­TIONS IN THE LITERATURE
ACCOMPANYING THE APPLIANCE.

AMEUBLES - Cet appareil ne doit
être placé que sur un meuble (avec
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation d’une
force excessive et des surfaces irrégulières risquent de
déstabiliser l’ensemble et de le renverser.

and the back or bottom are provided for ventilation and
to ensure reliable operation of the TV and to protect it
from overheating, these openings must not be blocked
or covered. The openings should never be blocked by
placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a
radiator or heat register. This TV should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
POWER SOURCES - This TV should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or
local power company. For TVs intended to operate
from battery power, or other sources, refer to the oper­ating instructions.
GROUNDING OR POLARIZATION - This TV is
equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is
a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.

cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, con­venience receptacles, and the point where they exit
from the appliance.

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

13. OUTDOOR ANTENNA GROUNDING - If an outside

antenna or cable system is connected to the TV, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up stat­ic charges. Article 810 of the National Electrical Code,
ANSI/NFPANo. 70, provides information with respect
to proper grounding of the mast and supporting struc­ture, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode.
(Fig. A)

14. LIGHTNING - For added protection for this TV receiv-

er during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV due to lightning and
power-line surges.

15. POWER LINES - An outside antenna system should

not be located in the vicinity of overhead power lines or
other electric light of power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as con­tact with them might be fatal.
OVERLOADING - Do not overload wall outlets and

16.
extension cords as this can result in a risk of fire or
electric shock.

17.

OBJECT AND LIQUID ENTRY - Never push
objects of any kind into this TV through openings as
they may touch dangerous voltage points or short out
parts that could result in a fire or electric shock. Never
spill liquid of any kind on the TV.

18. SERVICING - Do not attempt to service this TV

yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
DAMAGE REQUIRING SERVICE - Unplug this

19.
TV from the wall outlet and refer servicing to qualified
service personnel under the following conditions:

a. When the power supply cord or plug is damaged or

frayed.

b. If liquid has been spilled, or objects have fallen into

the TV.

c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the

operating instructions. Adjust only those controls that
are covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.

e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance,

this indicates a need for service.

20. REPLACEMENT PARTS - When replacement parts
are required, be sure the service technician uses
replacement parts specified by the manufacturer that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, injury to persons or other hazards.

21.

SAFETY CHECK - Upon completion of any service
or repairs to this TV, ask the service technician to per­form routine safety checks to determine that the TV is
in proper operating condition.

22. HEAT - This TV product should be situated away
from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that
produce heat.

FCC WARNING - This equipment may
generate or use radio frequency energy.
Changes or modifications to this equip­ment may cause harmful interference
unless the modifications are expressly
approved in the instruction manual.
The user could lose the authority to
operate this equipment if an unautho­rized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building as close to the point of cable entry as practical.

PREPARATION FOR USE

2

1

3

L

Y

P

b

P

r

R

L

V

I

D

E

O

2

A

U

D

I

O

R

V

I

D

E

O

1

S

-

V

I

D

E

O

VIDEO

H

E

A

D

P

H

O

NE

A

N

T

A

U

D

I

O

C

O

M

P

O

N

E

N

T

R

L

S

-V

ID

E

O

VIDEO

ANT

H

EA

D PHO

NE

VIDEO1

A

U

D

IO

L

Y

P

b

P

r

R

L

V

I

D

E

O

2

A

U

D

I

O

R

V

I

D

E

O

1

S

-

V

I

D

E

O

VIDEO

H

E

A

D

P

H

O

N

E

A

N

T

A

U

D

I

O

C

O

M

P

O

N

E

N

T

L

Y

P

b

P

r

R

L

R

C

O

M

P

O

N

E

N

T

V

ID

E

O

2

AUDIO

A

U

D

IO

MENU

SELECT

POWER

VOLUME

CHANNEL

L

Y

P

b

P

r

R

L

V

I

D

E

O

2

A

UDIO

R

V

I

D

E

O

1

S

-

V

I

D

E

O

V

ID

E

O

H

E

A

D

P

H

O

N

E

A

NT

A

U

D

I

O

CO

M

P

O

N

E

N

T

AN

T

IN

OUT

INPUT

SELECT

123

456

789

0

+100

MENU

o

n

p

m

MUTE SLEEP

DISPLAY

CH RET

INPUT

SELECT

POWER

CH

VOL

CONNECTIONS

Plug the incoming cable into the ANT jack on the rear of the TV.

Cable

TV signal

You can bracket this product as wall mounting TV using the arm adapted for 100mm (commercially available).

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.

Note:

For your safety and to avoid damages to the unit, unplug the antenna cable from the

•

ANT jack before moving the unit.

[EXTERNAL CONNECTION]

VIDEO1 input

ex.

Video Cassette
Recorder

Notes:

●

The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.

●

The S-VIDEO jack is given priority over the VIDEO jack.

VIDEO2 input

ex.

Antenna

OR

Incoming cable from home Antenna /
Cable Company (No Cable Box)

Cable Box or
Satellite Box*

OR

Incoming cable from Cable
Company or Satellite Antenna

(OUT)

Audio Cable

(OUT)

Video Cable

(OUT)

OR

S-Video Cable

(OUT)

Rear of this TV

*

NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and require
a special converter to receive these channels. Consult
your local cable company.

Rear of this TV

(IN)

(IN)

(IN)

(IN)

Rear of this TV

SELECTING AUDIO/VIDEO INPUT

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by
pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input
mode changes by pressing the button as following:

TV channel VIDEO1 VIDEO2

PHOTO STAND

Photo Stand

Adjust the length of the stand in 5 levels to
change the angle of the TV.

OPERATIONS

REMOTE CONTROL AND FRONT PANEL FUNCTION

To send infrared ray (IR) signal

To decide the command of settings

To display CH No./Audio Status

IR transmitter

POWER button

To turn TV on/off

VOL XX/YYbuttons

To adjust volume

MENU button

To view on-screen menu

MUTE button

To mute sound

DISPLAY button

INPUT SELECT button

To select TV or external input

CH KK/LLbuttons

To select channels and move
up/down through menu items

Channel number buttons

Press two digits to directly access the
desired channel. Remember to press
a "0" before a single digit channel.

+100 button

Press to select cable channels
higher than 99.

SLEEP button

To set Sleep Timer

CH RET button

To return to previous channel

Audio Cable

Video Camera

(IN)

(OUT)

Video Game

Component
Video Cable

Notes:

●

This TV can accept 480p / 480i / simplified 1080i video signal.

●

Simplified 1080 video signal differs to the original 1080i video signal because it is displayed
after converted into 480p signal.

INSTALLING THE BATTERIES

Install two AAA batteries (supplied) matching
the polarity indicated inside battery compart­ment of the remote control.

[BATTERY PRECAUTIONS]

• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.

•

Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.

• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

INITIAL SETUP

When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed.
The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.

1

1

Select the desired
language according to
the screen indication.
After that, the TV
performs “AUTO
PRESET CH” to scan
channels available for
the broadcasting in
your area.

When the scanning is completed, or
tuner stops on the lowest memorized channel.

Notes:

●

In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.

●

If those settings do not work properly, please call our help line on the front page of this owner's manual.

SELECT LANGUAGE

ENGLISH NEXT:PRESS CH

ESPAÑOL DESPUÉS:PRESIONE CH

FRANÇAIS APRÈS:PRESSEZ VOL

PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
THEN PRESS CH
IN ORDER TO PERFORM
“AUTO PRESET CH ”.

– INITIAL SETUP –

K

,

[MENU] is pressed during channel scanning to cancel it, the

K

L

X

2

2

If the TV screen shows
snow noise and there is
no operation for more
than 5 seconds,
“HELPFUL HINTS”
appears. Follow the
instructions listed on­screen.

- HELPFUL HINTS -

1. PLEASE CHECK TO SEE IF THE
ANTENNA/CABLE/SATELLITE IS
PROPERLY CONNECTED.

2. DID YOU PERFORM “AUTO PRESET CH” ?

3. PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.

Note:

●

You can test if the remote control sends out the infrared signal with an AM radio.
(Refer to “TROUBLESHOOTING GUIDE”.)

MENU button

To view on-screen menu

VOLUME XX/YYbuttons

To adjust volume

CHANNEL KK/LLbuttons

To select channels

SELECT button

To select TV or external input

POWER button

To turn TV on/off

Infrared Sensor Window

Note:

●

If some digits appear in the corner of the screen when the unit is turned on at the first time,
press [POWER] without unplugging the power cord.

OPERATIONS (Continued)

15

ADD/DELETE

Regular

-None-

STEREO

SAP

Stereo

broadcast

Menu

Selection

Type of

broadcast

MAIN

MONO

SAP*

-None- -None-

MONO

STEREO

SAP

MAIN

MAIN

MENU

MENU

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

SLEEP 10 MINUTE

o

p

CH

m

n

VOL

MENU

o

p

CH

CHANNEL SETTING

[AUTO PRESET CHANNELS]

Channel presetting is necessary at the start or
in case you moved the TV to a different area.
This feature automatically scans and memo­rizes all available channels in your area and
lets you easily select with [CH ▲ /▼].

1

1

Select “CHANNEL SET UP”

MENU

CH

o

p

VOL

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

m

Select “AUTO PRESET CH”

2

2

CH

o

p

VOL

- CHANNEL SET UP -

ADD/DELETE CH (TV)

AUTO PRESET CH

m

The tuner starts scanning automatically.

3

After scanning

3

(completed)
The lowest memo-

15

rized channel appears.

OR

(in failure)
Check antenna con­nection and try again.

NO TV SIGNAL

Note:

●

The TV may recognize TV channels as
CATV channels if reception condition is
poor. If this happens, check the antenna
connections and try scanning again when
reception conditions are better.

SLEEP TIMER SETTING

1

1

Select “SLEEP”

MENU

CH

o

p

VOL

m

n

• The time increases by 10
minutes up to 90.

MULTI-CHANNEL TELEVISION SOUND (MTS)SYSTEM

1

Select “TV SOUND”

1

CH

o

p

VOL

2

2

m

n

[MAIN] [MONO] [SAP]

3

3

To exit the menu

Select the desired sound
mode

[ADDING/DELETING CHANNELS]

You can add channels that was not memorized
by AUTO PRESET CH due to the bad recep­tion status and also delete channels you no
longer receive or seldom watch.

1

1

Select “CHANNEL SET UP”

MENU

CH

o

p

VOL

m

2

2

Select “ADD/DELETE CH”

VOL

m

3

3

Select the channel you wish

CH

o

p

4

4

Add or delete the channel

VOL

m

n

5

5

To exit the menu

MENU

Notes:

●

When you disconnect the unit from the AC
outlet or when you have a power failure, the
sleep time will be lost.

●

To cancel the sleep timer,
press [SLEEP] repeatedly
until “SLEEP 0 MINUTE”
is displayed.

●

The Sleep Timer Setting
display will disappear
automatically after 10 seconds of the operation.

●

You can also set the Sleep Timer by press­ing [SLEEP] repeatedly.

*Second Audio Program (SAP) :

Your program can also be received in a
second language or sometimes a radio
station.

Note:

●

If you select [SAP] when second audio is
not available, the TV will receive normal
audio.

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

- CHANNEL SET UP -

ADD/DELETE CH (TV)

AUTO PRESET CH

Add: light blue
Delete: light red

BRIGHTNESS

Adjust until the darkest parts of the picture are
as bright as you prefer.

[-] : decrease brightness
[+] : increase brightness

CONTRAST

Adjust to increase or decrease contrast.

[-] : decrease contrast
[+] : increase contrast

COLOR

Adjust to be brilliant or pale color.

[-] : be pale color [+] : be brilliant color

TINT

Adjust to obtain natural skin tones.

[-] : add red [+] : add green

SHARPNESS

Adjust the detail of the picture.

[-] : less clear [+] : more clear

BACK LIGHT SETTING

1

1

Select “BACK LIGHT”

MENU

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

CLOSED CAPTION

You may view specially labeled (cc) TV
programs, movies, news and prerecorded
tapes, etc. with either a dialogue caption or
text display added to the program.

1

Select “CAPTION”

1

MENU

CH

o

p

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

[CAPTION MODE (CAPTION1, CAPTION2)]

●

CAPTION1
displays standard closed captions (what a
character is saying).

●

CAPTION2
displays foreign language closed captions
(foreign language words showing what a
character is saying).

●

There are three ways of displaying
according to programs:
Paint-on mode: Displays input characters

on the screen immediately.

Pop-on mode : Once characters are stored

in memory, they are
displayed all at once.

Roll-up mode : Displays the characters

continuously by scrolling
(max. 4 lines).

OPTIONAL SETTINGS

Note:

●

The display will disappear automatically
after 10 seconds unless you press any but­tons.

2

2

Select the desired brightness mode

[BRIGHT]

3

3

To exit the menu

2

Select the desired caption mode

2

VOL

[NORMAL]

[DARK]

m

n

[OFF]

[CAPTION1][CAPTION2]

[TEXT2] [TEXT1]

3

3

To exit the menu

MENU

[TEXT MODE (TEXT1, TEXT2)]

●

TEXT1 and TEXT2
display half-screen text
by scrolling (such as a
channel guide, schedule
or announcement).

Notes:

●

If closed captioning is not broadcasted, you
cannot receive it and nothing is displayed.

●

When your TV receives a special effects
playback signal (i.e., Search, Slow and Still)
from a VCR’s video output channel (CH3 or
CH4), the TV may not display the correct
caption or text.

●

Captions and texts may not match the TV
voice exactly.

●

Interference may cause the closed caption
system not to function properly.

●

The caption or text characters will not be
displayed while the menu display or
functions display is shown.

●

If a black box appears on the screen, this
means that the TV is set to TEXT mode. To
clear screen, select [CAPTION1],
[CAPTION2] or [OFF].

PICTURE ADJUSTMENT

1

Select “PICTURE”

1

MENU

VOL

m

- TV SET UP -

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

2

Select an item to adjust

2

[BRIGHTNESS] [CONTRAST]

[SHARPNESS] [TINT]

3

Adjust the setting

3

VOL

...

m

n

...

+

–

-+

[COLOR]

BRIGHTNESS

LANGUAGE SELECTION

1

1

Select “LANGUAGE”

MENU

CH

o

p

PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
SLEEP [0] MINUTE

- TV SET UP -

2

Select the desired language

2

VOL

m

n

[ENGLISH] [ESPAÑOL]

[FRANÇAIS]

3

3

To exit the menu

MENU