Sylvania 6420FMG User Manual

Owner’s Manual
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMP
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC ART 250, PART H)
S2898A
GROUND CLAMPS
GROUNDING CONDUCTORS (NEC SECTION 810-21)
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
6420FMG
20 INCH COLOR TELEVISION
FEATURES
181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.
PLL Frequency Synthesized Tuning- Provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons on the remote control.
Sleep Timer
Closed Caption Decoder
Auto Shut Off Function- If there is no signal input from the antenna terminal and no user operation for 15 minutes, the TV will turn itself off automatically.
V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.
Tinted, Bright Black Matrix Picture Tube
Full-Function Remote Control
On-Screen Function Display
AV Input
Resume Function- If the power fails or is disconnected while the TV is on, the TV will turn on automatically when the power resumes.
Flat Screen Picture Tube
PRECAUTIONS
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase Dealer Purchase from Dealer Address
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE VISIT OUR WEB SITE AT
http://www.SylvaniaConsumerElectronics.com
Dealer Phone No. Model No. Serial No.
1-800-968-3429
OR
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PAR TS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PROD­UCT TO OBTAIN SERVICE UNDER THIS WARRANTY. This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not pur­chased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not sup­plied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alter­ation, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SER­VICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VA RY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
of original retail purchase.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please contact us at :
http://www.SylvaniaConsumerElectronics.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in Malaysia 1EMN22024
FUNAI CORPORATION
Customer Service
Tel :1-800-968-3429
L3319UV * * * * *
IMPORTANT SAFEGUARDS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
1. READ INSTRUCTIONS - All the safety and operat- ing instructions should be read before the appliance is operated.
2.
RETAIN INSTRUCTIONS - The safety and operat­ing instructions should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS - All operating and use
4. instructions should be followed.
5.
CLEANING - Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol clean­ers. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninter­rupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. ATTA CHMENTS - Do not use attachments not rec-
6. ommended by the TV manufacturer as they may cause hazards.
7.
WATER AND MOISTURE - Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting of the appliance should follow the manu­facturer’s instructions and should use a mounting acces­sory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
: TO REDUCE THE RISK OF ELECTRIC
PORTABLE CART WARNING
S3126A
9. VENTILATION - Slots and openings in the cabinet
10. POWER SOURCES - This TV should be operated
11.
12.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUT­ING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERAT­ING AND MAINTENANCE INSTRUC­TIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
AMEUBLES - Cet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufactur­er’s instructions have been adhered to.
only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the oper­ating instructions. GROUNDING OR POLARIZATION - This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. POWER-CORD PROTECTION - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, con-
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
venience receptacles, and the point where they exit from the appliance.
13.
OUTDOOR ANTENNA GROUNDING - If an out­side antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides infor­mation with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conduc­tors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the ground­ing electrode. (Fig. A)
14. LIGHTNING - For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or cir­cuits as contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.
SERVICING - Do not attempt to service this TV
18. yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19.
DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into
the TV.
c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance,
this indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this TV, ask the service technician to per­form routine safety checks to determine that the TV is in proper operating condition. HEAT - This TV product should be situated away from
22. heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
FCC WARNING - This equipment may generate or use radio frequency energy. Changes or modifications to this equip­ment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equip­ment if an unauthorized change or modification is made.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building as close to the point of cable entry as practical.
MENU
VOLUME
CHANNEL
POWER
MENU
VOLUME
CHANNEL
POWER
PREPARATION FOR USE
ANT.
AUDIO
VIDEO
ANT.
IN
OUT
AUDIO
VIDEO
2
1
3
15
[-]
GAME MODE
[+]
OFF ON
VIDEO
15
123
456
789
0
+100
MENU
o
n
p
m
MUTE SLEEP
DISPLAY
CH RET
GAME
POWER
CH
VOL
CONNECTIONS
Plug the incoming cable into the ANT. jack on the rear of the TV.
Cable
TV signal
OR
Antenna
Rear of this TV
You can enter into Video mode from Game mode by adjusting a Picture control.
To cancel Game mode only
1
To use external input
1
GAME
GAME
2
2
MENU
m
VOL
Incoming cable from home Antenna / Cable Company (No Cable Box)
Cable Box or
OR
Incoming cable from Cable Company or Satellite Antenna
Cables not included
Satellite Box*
*Note (DO NOT DISCONNECT FROM BOX) Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note:
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT. jack before moving the unit.
[EXTERNAL CONNECTION]
AUDIO/VIDEO input
ex.
Audio Cable
(OUT)
Video GameVideo Camera
(OUT)
Video Cable
(IN)
(IN)
Rear of this TV
INSTALLING THE BATTERIES
Install two AAA batteries (not supplied) matching the polarity indicated inside battery compartment of the remote control.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
Picture: GAME (ON)
External
Input:
Select “PICTURE” After 10 seconds
Picture: Customized Input: External
3
3
To return to TV channel
GAME
2 times
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
To send infrared ray (IR) signal
To decide the command of settings
To display CH No./Audio Status
Note:
You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)
IR transmitter
POWER button
To turn TV on/off
VOL XX/YYbuttons
To adjust volume
MENU button
To view on-screen menu
MUTE button
To mute sound
DISPLAY button
GAME button
Press to set the Game mode.
CH KK/LLbuttons
To select channels and move up/down through menu items
Channel number buttons
Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.
+100 button
Press to select cable channels higher than 99.
SLEEP button
To set Sleep Timer
CH RET button
To return to previous channel
INITIAL SETUP
When you turn on the power for the first time, the “SELECT LANGUAGE” menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.
1
1
Select the desired language according to the screen indication. After that, the TV performs “AUTO PRESET CH” to scan channels available for the broadcasting in your area.
SELECT LANGUAGE
ENGLISH
NEXT:PRESS CH
ESPAÑOL
DESPUÉS:PRESIONE CH
FRANÇAIS
APRÈS:PRESSEZ VOL
– INITIAL SETUP –
PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. THEN PRESS CH K, IN ORDER TO PERFORM “AUTO PRESET CH”.
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.
Notes:
In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
If those settings do not work properly, please call our help line on the front page of this owner's manual.
SELECTING AUDIO/VIDEO INPUT
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control.
You can select external input jacks by pressing [GAME] on the remote control.
1
1
To use external input
GAME
GAME
2
2
If the TV screen shows
K
L
K
snow noise and there is no operation for more than 10 seconds, “HELPFUL HINTS” appears. Follow the
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/ SATELLITE IS PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH” ?
3. PLEASE REFER TO FRONT PAGE OF THE OWNER’S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION.
instructions listed on the screen.
2
2
To return to TV channel
GAME
Infrared Sensor Window
POWER button
To turn TV on/off
CHANNEL ▲ /▼ buttons
To select channels
VOLUME
XX/YY
buttons
To adjust volume
MENU button
To view on-screen menu
Note:
If some digits appear in the corner of the screen when the unit is turned on for the first time, press [POWER] without unplugging the power cord.
External
Picture: GAME (ON) Input:
In the Game mode, you can use input jacks with suitable picture adjustments for video games.
Notes:
If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.
If you adjust another picture control while in Game mode, this mode will automatically be canceled.
Loading...
+ 2 hidden pages