Swisher ZT1436 User Manual

Download

Page 1

swisherinc.com

OWNER’S

MANUAL

MODEL NO. ZT1436 ZT17542B ZT1842 ZT20050

“Z” SERIES

“Z” SERIES“Z” SERIES

ZERO TURN HYDROSTATIC DRIVE

IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment.

Rev.02.19.2003

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093

PHONE 660-747-8183 FAX 660-747-8650

Manufacturing quality lawn care equipment since 1945

ZERO TURN HYDROSTATIC DRIVEZERO TURN HYDROSTATIC DRIVE

Assembly Operation Service and Adjustment Repair Parts

Made In The

USA

ONZTR03

Page 2

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions:

1) Engine Warranty All engines utilized on our products have a separate warranty extended to them by the individual engine manufacturer. Any engine service difficulty is the responsibility of the engine manufacturer and in no way is Swisher Mower Co., Inc. or its agents responsible for the engine warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-233-

3723. The Tecumseh Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use This product is not intended for commercial use and carries no commercial warranty.

3) Limitation This warranty applies only to products which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher Mower Co., Inc., that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3 SAFETY…………………………4-7 OPERATION……………………8-10

MAINTENANCE…………………….11-12 SERVICE / ADJUSTMENT……….…13-16 PARTS BREAKDOWN……………...17-21 TROUBLESHOOTING………………..22

Page 3

Thank you for choosing Swisher’s ZTR Mower. Before operating your mower, please read, understand and follow all of the safety precautions and other instructions explained in this manual . As with all power equipment, lawnmowers can be potentially dangerous if improperly used.

SAFETY PRECAUTIONS & DECALS

This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death.

Page 4

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting, adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate this machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the mower discharge direction and do not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Keep children under the watchful care of another responsible adult.

• No riders!

• Do not put hands or feet near or under rotating parts. Keep clear of the discharge

opening at all times.

• Do not mow in reverse. Always look down and behind before and during backing.

SAFETY PRECAUTIONS & DECALS

The operation of any cutter can encounter foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles for over spectacles before staring any cutting machine and while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended.

Page 5

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw

them.

SLOPE OPERATION!

Do not operate on slopes greater than 15 degrees. Use extra caution when mowing on slopes. Operate self-propelled units up and down slopes. There is a significant risk of overturns when operating across slopes. If you feel uneasy on a slope then do not mow it.

•Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine.

•Watch for traffic when operating near or crossing roadways.

•Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage.

Repair mower as necessary.

•Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.

•Never allow operation by untrained persons.

•Do not operate the machine while under the influence of alcohol or drugs.

•Operate self-propelled machines up and down slopes. There is significant risk of

overturns when operating across slopes. Avoid sudden turns. Operate walk-behind machines across slopes. There is a significant risk of slipping under a walk-behind machine when operating up and down slopes.

• Never tamper with safety devices. Check their proper operation regularly.

•Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running. Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when servicing them. Do not operate at too fast a rate.

• Do not mow close to ditches, embankments or drop-offs. An edge could collapse. A

mower wheel over the edge could suddenly turn the unit over.

•Do not mow on wet grass if possible. Wet grass causes reduced traction and could cause

sliding. Do not park on a slope unless absolutely necessary.

• Always chock or block wheels and set parking brake if parked on slope.

Page 6

SAFETY PRECAUTIONS & DECALS

WARNING: Hydraulic fluid can cause severe burns and penetrate skin causing

severe injury or death.

• Do not step on mower deck when operating, dismounting or mounting the mower.

• Never push or pull unit with another vehicle. Transmission damage will occur.

• When transporting be sure to secure mower frame to transport vehicle. NEVER tie

down to moving parts or linkages which may become damaged or come loose.

• NEVER transport mower while engine is running.

• NEVER add fuel or remove gas cap while engine is running or hot.

• NEVER store unit near an open flame such as a water heater or furnace.

• NEVER modify or allow anyone to modify or alter any components or safety

devices.

• ALWAYS keep mower clean and free of debris and grass clippings.

• NEVER reverse battery cables. Electric shock will occur.

• ALWAYS keep battery away from open flame and sparks. Explosive gases

from

battery can cause serious injury or death.

• ALWAYS wear safety glasses and protective gear when servicing battery. Battery fluid contains sulfuric acid. Contact with battery acid on skin or clothing can cause severe chemical burns.

• NEVER tip battery beyond a 45 degree angle in any direction.

Page 7

SAFETY PRECAUTIONS & DECALS

Danger/Warning Decal – OD99155

Ignition/PTO/Throttle Decal – OD99154

Ignition/PTO/Throttle Decal 50” Mower Only – OD99157

Parking Brake Decal – OD99152

Flying Debris Decal – OD53

Triangle Danger Decal – OD55

No Step Decal – OD11

DECALS NOT SHOWN

36” Decal – OD108 & OD112 42” Decal (17.5 HP Engine) – OD109 & OD113

Height Indicator Decal - OD99151 Height of Cut Decal - OD99153

(18 HP Engine) – OD110 & OD114

Swisher Flag USA Decal – OD39

50” Decal – OD111 & OD115

Page 8

OPERATING YOUR NEW ZTR MOWER (cont.)

CONTROLS

●

OPERATOR PRESENCE SYSTEM:

mower is equipped with an operator’s presence system. Any attempt to leave the seated position with the engine running, without first disengaging the PTO switch and placing the steering levers in the neutral position, will cause the engine to shut off.

●

WARNING:

the Operator’s Presence System is functioning as described.

●

PARKING BRAKE:

brake before starting. The parking brake is located on the drivers left hand side. Engage the parking brake by pushing the lever rearward and down until lever locks into position. Be sure to release parking brake before operating the machine.

●

IGNITION:

drivers right hand side toward the rear of the seat. The ignition switch has three positions: OFF, ON, START.

●

THROTTLE:

located on the drivers right hand side towards the front of the seat. For maximum performance and battery charging, operate mower at full throttle. When starting a cold engine, place lever forward in the full choke position. After start up, move throttle rearward to full throttle position. Move lever all the way to the rear for lowest setting before shutting off engine. The 50” Model has a choke mounted on the right side fender for easier cold weather starts.

●

PTO SWITCH:

switch is used to engage the blades of the mower. When the PTO switch is pulled out the blades will be engaged. When the PTO switch is pushed in the blades will be disengaged. The PTO switch must be pushed in to complete the Operator’s Presence System to start engine.

●

NEUTRAL LOCK:

in the outward and locked position for the mower to start. ( See page 12)

o not operate the machine unless

Always set the parking

The ignition switch is located on the

The throttle\choke control is

The PTO, or Power Take Off

The steering levers must be

This

STARTING MOWER

• TO START:

neutral locked position. Engage parking brake. Extend throttle to full choke position*. Start ignition and slide throttle lever back to full throttle position. Allow engine to warm up for 1 minute. Release parking brake

• * Model ZT20050 has a remote choke assembly located on the right fender, behind the rider.

• FORWARD MOVEMENT:

forward gently push both steering levers forward equal distance from the neutral position. The further you move the levers forward the faster you will travel. CAUTION steering levers have quick response timing.

• BACKWARD MOVEMENT:

mower backwards, gently pull back on the steering levers the same distance from neutral. The further you pull back the faster you will travel. normal for the reverse speed to be less than the forward for easier turning.

• TURNS:

forward then the left. For right turn, move the left lever farther forward than the right. To obtain a tight turning radius, GENTLY reverse one lever and push the other lever forward. CAUTION: Aggressive turns can damage lawns. Do not make turns with the inside wheel stopped. It it better to keep both wheels turning slightly.

• DECK HEIGHT ADJUSTMENT:

mower deck up and down, simply rotate the lever located in front of the seat above the floor plate. Clockwise raises the deck. Counterclockwise lowers the deck. The deck is adjustable from 1 ½” to 3 ½”.

• For best performance, grass over 6 ½” in height should be mowed once in the highest position and once again at desired cut height.

• ENGAGING BLADES

for operation of blades. With engine to full throttle position, pull UP on PTO switch located between the throttle and the key switch. To disengage blades, push DOWN on PTO switch.

Position steering handles outward to

To move the mower

To move the

NOTE

For left turn, move the right lever farther

: Operator must be seated

it is

To raise the

• STOPPING ENGINE:

outward neutral locked position. Push PTO switch in to disengage. Place throttle lever to lowest setting and let idle for 30 seconds. Turn off ignition key and engage parking brake.

Place both levers in the

Page 9

OPERATING YOUR NEW ZTR MOWER (cont.)

MOWING

• WARNING: Do not operate mower at too fast of a rate. Sudden movements forward and backward at fast speeds can cause accidents resulting in personal injury

• Start out slowly moving steering levers SLOWLY forward and backward until you learn to operate the unit. NOTE: This mower has been designed to be very maneuverable. Practice in open, flat areas is extremely necessary to become comfortable and efficient with the controls.

• BEGIN TO MOW: Before starting the engine, set the desired deck height.

• Start the mower engine.

• Position the throttle lever about halfway and engage PTO switch. Reposition throttle lever to full throttle position.

• Move steering levers forward to begin mowing.

• CAUTION:

Failure to do this will cause damage to the PTO belt.

• STOPPING: Hydrostatic mowers use hydrostatic braking through the transmissions. To slow or stop the unit move the steering levers to the neutral position

• STOPPING THE ENGINE: Move the throttle lever to slow position, allow engine to idle for 30 seconds and turn ignition to off position. CAUTION: Failure to position the ignition key to any position except off will cause discharge of the battery.

Always make sure the deck is not plugged with grass or other debris.

Page 10

MAINTENANCE SCHEDULE

INSPECT BEFORE EACH USE

Loose fasteners

blades.

Parking brake

or repaired.

: Be sure all fasteners are at proper torque. Especially guards and

: If brake does not keep unit from rolling, brake must be adjusted

Tires

recommendation). Check for damage due to sharp rocks, objects or stumps.

Operator Presence System:

is disengaged and the control levers are locked in the neutral position. Any attempt to leave the seated position with the PTO switch engaged will kill the engine.

Oil level

level. Never operate engine with the oil level below the add mark on the dipstick. Be sure to tighten the dipstick securely after inspection. Refer to engine manual for additional information.

: Always check and maintain proper tire pressure (See tire sidewall for

The engine should not start unless the PTO switch

: To prevent damage to engine, always check and maintain proper oil

INSPECT EVERY 8 HOURS

Proper cleaning:

cloth from engine, battery, deck and and transaxles. Do not use harsh chemicals or abrasives. Keep all painted surfaces and wheels free of oil and gasoline. Protect all painted surfaces with an automotive wax. Do not spray unit with water or store outdoors unprotected. Water can invade sealed bearings and reduce component life.

Remove any build up of grass, dirt or debris with a brush or

Do not spray water onto hydrostatic transmissions. This will

cause injection of water into the unit causing failure.

Air filter:

Check filter before starting the engine. Check for buildup of dirt or debris. Replace if bent, clogged, or damaged.

Oil level:

level. Never operate engine with the oil level below the add mark on the dipstick. Be sure to tighten the dipstick securely after inspection.

The engine will not run properly with a dirty or damaged air filter.

To prevent damage to engine, always check and maintain proper oil

Page 11

MAINTENANCE SCHEDULE

INSPECT EVERY 25 HOURS

-Lubrication: Grease all pivot points with a high temp grease

Battery, check and clean:Keep battery terminals clean and tight. Periodic

charging will extend its life. Clean terminals with a wire brush and coat with a petroleum jelly.

-Change engine oil and filter

for instructions. Select viscosity grade according to your expected environmental temperature.

Blades:Best results will come from sharp blades. Replace if bent, damaged or worn.

Engine air screen: Screen must be clean and free of debris for proper engine

cooling. Clean with a brush or cloth. Do not spray with pressurized water.

Muffler:Inspect for damage or corrosion. Keep free of grass or debris to prevent

fire.

Use only quality detergent oil. See engine manual

INSPECT CHECK EVERY 100 HOURS

Clean engine cooling fins: Clogged cooling fins can damage engine due to

overheating.. Keep fins and external surfaces of the engine clean.

Replace air filter: The engine will not run properly with a dirty or damaged air

filter. Check filter before starting the engine. Check for buildup of dirt or debris. Replace if bent, clogged, or damaged. See engine manual for detailed instructions.

Replace spark plugs:See engine manual for detailed instructions.

INSPECT EACH SEASON

-Belts

Check belts for wear and deterioration. See service and adjustments.

Spark plug: See engine manual for detailed instructions.

Replace in-line fuel filter

INSPECT BEFORE STORAGE

-Change engine oil and filter: See engine manual for detailed instructions.

-Lubrication

Check battery

will extend its life. Clean terminals with a wire brush and coat with a petroleum jelly.

Loose fasteners

blades.

Grease all pivot points with a high temp grease.

Keep battery terminals clean and tight. Periodic charging

Be sure all fasteners are at proper torque, especially guards and

Replace every season.

Page 12

SERVICE / ADJUSTMENTS

CAUTION:

Before performing any service or adjustments do as follows:

1. Turn off PTO switch.

2. Position unit on smooth flat surface.

3. Place steering levers in outward, neutral-locked position.

4. Turn ignition key “OFF” and set parking brake.

5. Wait for all moving parts to stop and disconnect spark plug wire.

TRACKING

Adjustments to the unit may need to be made if the unit does not track in a straight line. The primary reason for the unit not tracking straight is incorrect or unbalanced tire pressure. Before making any adjustments first check and adjust the tire pressure. DO NOT EXCEED MAXIMUM RECOMMENDED TIRE PRESSURE.

ADJUST LINKAGE: Place steering levers outward locking them in the neutral position. Turn off engine and raise seat. Under the seat are (4) adjustment bolts. The two adjustment bolts toward the seat mount are adjustments for the forward travel. The two bolts toward the engine or are for the reverse travel. Clockwise movement for these adjustments will decrease or slow the travel speed of the individual side. Counterclockwise movement will increase the travel of the individual side. The linkage is factory set to maximum performance. Adjustment is made by rotating the adjustment bolt clockwise on the opposite side that the unit tracks toward. Adjust forward and reverse to track straight as needed. When accomplished adjustment to the steering levers may need to be done. This is made by loosening the the two bolts on the steering lever and aligning with the other. Travel of the steering levers from front to rear may be accomplished in the same manner.

Neutral-Lock Position

Steering levers out.

Adjustment bolts

Both sides

Tracking Adjustment

Diagram

Decrease Speed

Front of

Mower

Increase Speed

Page 13

SERVICE / ADJUSTMENTS

REMOVING THE MOWER DECK

1. Turn off engine and engage parking brake.

2. Rotate cutting height lever counterclockwise to lowest cutting position.

3. Remove bolt from pickup point located at the front of the deck.

4. Remove cotter pins on rear hanger points and slide out stabilizer bars.Disconnect tension spring bolt from tension bracket.

5. Remove belt from mower pulley and electric clutch.

6. Slide mower deck from under unit.

INSTALLING THE MOWER DECK

1. Be sure the cutting height lever is in the lowest position.

2. Position mower deck under unit.

3. Install belt around mower pulley and electric clutch.

4. Install stabilizer bars into rear hanger brackets through lift points and install cotter pins. Be sure eye bolt is between bracket sides.

5. Install bolt in front hanger bracket passing through eyebolt in the same manner as rear and tighten snug.

6. Reattach tension spring bolt and tighten.

It is recommended to remove the

deck to sharpen the blades.

Remove eye-bolts (2 rear & 1 front)

Remove belt

Page 14

SERVICE / ADJUSTMENTS

LEVELING THE MOWER DECK

1. Position unit on a smooth level surface.

2. For side to side leveling, measure the distance from the floor to the bottom edge at the rear of the deck. The measurement should be equal within 1/16 inch side to side. Adjustment can be made by loosening locking nut on rear eyebolt hangers and adjusting up or down as needed.

3. For front to rear pitch adjustment, loosen locking nut on front eyebolt and adjust up or down as needed. Proper pitch measurement is 1/8” to 1/4”

Front of Mower

lower at the front of the deck.

Front of deck should be

slightly lower.

Distance should be

equal on both rear sides.

Ground

Page 15

SERVICE / ADJUSTMENTS

BELTS

Clutch drive belt replacement

1. Remove belt covers.

2. Disconnect tension idler from tension bracket.

3. Remove belt from mower pulley and electric

clutch.

Part #: 3816

Part #: 3752

4. Install new belt onto electric clutch and mower

pulley and check for proper routing and

clearance.

5. Reconnect idler tension bolt to tension bracket.

Part #: 3820

66LR- Transmission Belt

Transaxle belt replacement

1. Remove clutch drive belt. See clutch belt

replacement.

2. Disconnect wiring from electric clutch.

3. Disconnect idler spring from tension bracket.

4. Remove bolt and washer from bottom of electric clutch and slide clutch from engine crankshaft, set aside.

5. Remove belt from transaxles and engine pulley.

6. Install new belt. Check for proper routing and clearance.

7. Reinstall electric clutch carefully aligning keyed portion of clutch and keyway in crankshaft. Reinstall bolt and washer. Washer is “cupped” be sure to place “cupped” side of washer towards the clutch body.

8. Reconnect tension idler to tension bracket.

9. Reconnect wiring harness to electric clutch.

10. Reinstall clutch drive belt. See clutch belt

replacement.

Page 16

WIRING DIAGRAMS

36” and 42” Mowers

50” Mower

Page 17

SEAT DETAIL

(Page 20)

STEERING DETAIL

(Page 19)

4 235

Transmission Idler

Item # Description Part #

1 Battery Box 3696TK 2 5/16-18 X 3/4 Serr Flg Bolt NB596 3 5/16-18 Serrated Flange Nut NB170 4 Nuetral Switch Bracket Painted 3704TK 5 Return to Neutral Switch 3695 6 Steering Cover 3644TK 7 3/4 Push Nut Blk Plastic NB687 8 Bearing CB58

9 Caster Weldment 5072 10 1/8 X 1 Cotter Pin NB126 11 Front Tire for 36" and 42" 3754

Front Tire for 50" Only 5057 12 3/8-16 X 4 HCC GR5 Bolt NB645 13 3/8-16 Nyloc Nut NB182 14 ZTR Trans. Right- NOT FOR RE-SALE 3600

ZTR Trans. Left- NOT FOR RE-SALE 3601 15 Lug Nut 2203LN 16 Rear Tire For 36" 3755

Rear Tire For 42" 3604

Rear Tire For 50" 3756 17 Battery 230 CCA EBAT230 18 Hydro Release 3678TK 19 Spring - Interlock Switch 3751

ENGINE DETAIL

(Page 18)

FRAME DETAIL (Page 21 & 22)

TRANSMISSION IDLER DETAIL

13 14

DECK LIFT

(Page 23, 24 & 25)

DETAIL (Page 19)

OVERALL ASSEMBLY

Item # Description Part #

20 Transmission Idler Arm 3690TK 21 1/2-13 X 3 HCC GR5 Bolt ZP NB131 22 3/8-16 X 1 1/2 HCCGR5ZP NB107 23 3/8 SAE Washer NB272 24 Idler Pulley OD-2.16" B27 25 3/8-16 2-Way Lock Nut NB280 26 1/2-13 2-Way Jam Lock Nut NB121 27 5/16-18 Nyloc Nut NB181 28 Clutch Rod Spring 682S 29 Wire Link For Idler Arm BRS6H 30 5/16-18 X 1 HCC GR5 ZP NB501

Not Pictured

Description Part #

Solenoid Assembly (All Models) 9043

Wiring Harness (36 and 42" Models Only) 3720

Wiring Harness (50" Models Only) 3804

Hour Meter (50" Models Only) 3803

Battery Hold Down, 15" Tarp Strap BHOLD

1/4-20 X 3/4 GR5 ZP (2) NB250

1/4-20 Flange Nut (2) NB524

Belt Snubber (50" Mower Only) 3819TK

(This Page)

MOWING DECK DETAIL

Page 18

BLADE DRIVER

B4104TK

For 42 and 50” Mowers

Item # Description Part #

1 3/4-16 2 Way Lock Nut NB175

2 1.5x.761x.098x.134 Belleville Washer AS155

3 3/4ID X 1 1/4OD 10 GA. Washer NB184 4 Blade Pulley- 5" (42" Mower Only) 3785 5 Washer For Blade Driver NB179 6 Blade Bearing B98 7 Blade Shaft 4.25" 9076 8 Bearing Housing 9057TK 9 36" Mower - 18" Blade 9014

42" Mower - 20 1/2" Blade 9004

42" Mower - 22" Blade 9005

10 Blade Driver Assy 9018 11 1/4-20 X 3/4 GR5 ZP NB250

12 1/4-20 Nylok Nut NB180 13 3/8-24 Two Way Locknut NB216 14 Washer B98W 15 3/8-24 X 1 Bolt NB238 16 Blade Mount Plate 9008 17 SP Washer Bellvl. PLN .413 X .945 X .118 NB607 18 3/8-24 X 1 Engine Bolt Locktite NB238N 19 Blade Mount Plate Spacer (36" Only) 9024 20 3/8-16 X 1 1/2 HCCGR5ZP (36" Only) NB107 21 3/8-24 X 1 1/2 HCC GR5 ZP Locktite (36" Only) NB167N 22 3/8-16 2-Way Lock Nut (36" Only) NB280 23 Blade Pulley 4.5" (36" & 50" Only)

17.5" Blade for 50" Mower 5059

BLADE DRIVER

For 36” Mowers

3 (1 Used)

(2 Used)

ENGINE SETUP

Item # Description Part #

24 14 HP B&S Engine (36" Mower) N/A

17.5 HP B&S Engine (42" Mower) N/A 18 HP B&S Engine (42" Mower) N/A 20 HP B&S Engine (50" Mower) N/A

25 5/16-18 Serrated Flange Nut NB170 26 Spacer Engine Pulley BB105SL 27 Motor Pulley 3" 3753 28 1/4 X 1/2 Key Stock 4258 29 Engine Pulley Spacer Short .687 689S 30 Electric Clutch Drop Pulley 688ECDP

Electric Clutch (50" Mower Only) 3813

31 Washer Belleville Engine Pulley NB699 32 7/16-20 X 3.25 HCF GR5 ZP NB705

Page 19

STEERING (RIGHT)

6 27

192021

DECK LIFT

3843

264

3134

Item # Description Part #

1 Directional Handle Grip 3673 2 Directional Handle Weldment 3685TK 3 5/16-18 X 3/4 Serr Flg Bolt NB596 4 5/16-18 Serrated Flange Nut NB170 5 1/2-13 X 5 HCC GR5 ZP NB155 6 1/2 NR Mach Bushing 14 GA NB177 7 1/2 ID X 7/8 OD X 1/8 Nylon Washer NB682 8 Handle Mount Weldment Right 3635TK

9 Pivot Plate Right Weldment 3699TK

10 1/2-13 Nyloc Jam Nut NB688 11 1/2-13 2-Way Jam Lock Nut NB121 12 Washer TR150W 13 1/2-13 X 2 1/2 HCC GR5 ZP NB510 14 1/4 Rod End Male1/4-28 3721 15 1/4 Rod End Female 1/4-28 3708 16 1/4-20 Nylok Nut NB180 17 1/4-20 Flange Nut NB524 18 5/16-24 Hex Nut NB215 19 5/16-24 ZP 2-Way Lock Nut NB448 20 1/4-20 X 1 1/4 HTC GR5 ZP NB103 21 Universal Pivot Plate Weldment 3698TK 22 Control Card Left 3620TK

23 Tinnerman Clips 5/16-18 Heavy Duty 3669 24 1/4-20 X 3/4 SSC Plain NB310 25 5/16-18 X 1 1/2 Flge Serr. Bolt NB254 26 5/16-24 Jam Nut NB190 27 1/2-13 Nyloc Nut NB281 28 Tinnerman Clips 5/16-18 3706 29 Directional Control Linkage 3670 30 Plastic Knob- Black 4857 31 3/8-16 2-Way Lock Nut NB280 32 3/8 Hardened Washer NB196 33 3/8-16 X 1 1/4 GR5 ZP NB618 34 Height Adjust Crank 3710TK 35 Thrust Bearing T151 36 1/2-13 2-Way Jam Lock Nut NB121 37 Rear Height Lifter 3705TK 38 3/8 SAE Washer NB272 39 3/8-16 Nyloc Nut NB182 40 Rear Torsion Weldment 3684TK 41 Front - Back Height Link 3260TK 42 5/16-18 X 1 HCC GR5 ZP NB501 43 3/8-16 X 2 1/2 HCC GR5 ZP NB221 44 Front Torsion Weldment 3683TK 45 Lift Pivot 3663TK

Spacer .790 OD X .540 ID X .560 LG (2)

Handle Mount Weldment Left 3636TK

Pivot Plate Left Weldment 3700TK

Control Card Right 3621TK

NOT PICT URED

ES001

Page 20

SEAT BASE ASSEMBLY

Item # Description Part #

1 Seat 15" Back No Arm Rest (36" Mower Only) 3790

Seat 15" Back With Arm Rest (42" Mower Only) 3791

Seat 18" Back With Arm Rest (50" Mower Only) 3792 2 Seat Bracket 3807TK 3 Seat Hinge 3815TK 4 Tapered Spring 3609 5 Control Cover 3645TK 6 Seat Mount 3613C 7 5/16-18 Serrated Flange Nut NB170 8 5/16-18 X 3/4 Serr Flg Bolt NB596 9 5/16 SAE Washer NB556

10 5/16-18 X 1/2 Serr. Flg Bolt NB252 11 Seat Spring Bracket 3809TK 12 Tinnerman Clip 5/16-18 3706 13 5/16-18 Nyloc Nut NB181

Not Pictured

Operator Presence Switch

3798

SEE CONTROL CARD DETAIL THIS PAGE

11 8

CONTROL CARD

3722 ( Card for 36” & 42” Mowers)

3799 ( Card for 50” Mowers)

FUEL SUPPLY SYSTEM

(3259 For entire assembly)

Item # Description Part #

19 Gas Cap 6102NC 20 Gas Tank Plastic Black 6102T 21 Gas Tank Bracket 3258TK 22 1/4-20 X 1/2 Bolt NB109

Item # Description Part #

14 PTO Switch 3605 15 Key Switch 3623 16 1/4-20 X 1/2 MSC ZP Hex Washer NB114 17 Throttle Cable Assembly (36" & 42" Mowers) 3640

Throttle Control 35" (50" Mower Only) 3788

18 Control Cover Instruments (Right Side) 3646TK

Page 21

FRAME for 36” and 42” Mowers

242325

SEE DETAIL NEXT PAGE

Item # Description Part # Item # Description Part #

1 Beverage Retainer 3643TK 16 1/2-13 Nyloc Nut NB281 2 5/16-18 X 1/2 Serr. Flg Bolt NB252 17 1/2-13 X 2 1/2 HCC GR5 ZP NB510 3 5/16-18 Serrated Flange Nut NB170 18 Rear Hangar Bracket 3264TK 4 36" Mower Fender Left 3742TK 19 Frame Side Weldment 3639TK

36" Mower Fender Right 3742RTK 20 E-Brake Handle 3653TK

42" Mower Fender Left 3641TK 21 5/16-18 ZP 2 Way Lock Nut NB558

42" Mower Fender Right 3642TK 22 5/16-18 X 1 3/4 Flge Serr Bolt NB515 5 5/16-18 X 3/4 Serr Flg Bolt NB596 23 Transmission Fan Cover 3712TK 6 Fender Mount 3654TK 24 Trans Fan Cover Right Side 3806TK 7 Seat Base Weldment 3719C 25 E-Brake Side Link 3651 8 1/4-20 X 2 1/2 HTC GR5 ZP NB163 26 Bumper Weldment 3686TK 9 1/4-20 Flange Nut NB524 27 Upper Motor Base 3611TK

10 Access Plate 28 Rear Cover 3711TK

Access Plate Hinge 29 Transmission Mount 3703TK 11 Kick Plate 3630TK 30 5/16-18 X 2 1/4 Flang Serr. GR5 ZP NB622 12 5/16-18 X 1 1/2 Flge Serr. Bolt NB254 31 Parking Brake Weldment 3797TK 13 Height Adjust Bracket 3619TK 32 Brake Mount Plate 3267TK 14 Height Adjust Indicator 3671C 33 Brake Assembly Cog Right Side 3600CB-BA 15 Front Frame Weldment 3261TK Brake Assembly Cog Left Side 3601CB-BA

3269

Parts unique to 50” mower frame on next page.

Page 22

BRAKE LINKAGE DETAIL

(All Models)

35 37

FRAME FOR 50” MOWER

Item # Description Part #

35 1/4-20 Nylok Nut NB181

36 5/16 SAE Washer NB275 37 5/16-18 X 1 Eye Bolt NB202 38 Spring TR148S 39 Spring T2SM

Item # Description Part #

40 Bumper Weldment 3778TK 41 Upper Motor Base 3777TK 42 Transmission Mount 3787TK 43 Choke Mount 3810TK 44 50" Mower Fender Right 3783TK

50" Mower Fender Left 3784TK

45 Fender Mount 3782TK

These parts unique to 50” mower frame only.

Not Pictured

DESCRIPTION PART # QTY

Choke Cable 3789 1

3/8 Split Lock Washer NB711 1

3/8-24 HNF ZP NB456 1

Page 23

36” MOWING DECK

1012

SEE DETAIL THIS PAGE

NOT SHOWN

Roller Bracket (28) Mounting Hardware

DESCRIPTION PART # QTY

5/16-18 X 3/4 Serr Flg Bolt NB596 2

5/16-18 Serrated Flange Nut NB170 2

DECK IDLER

2425

4 5

SEE DETAIL

Page 18

Item # Description Part #

1 Deck Weldment 3750C

2 5/16-18 X 3/4 Serr Flg Bolt NB596 3 Pulley Cover 3743 4 5/16-18 Serrated Flange Nut NB170 5 Sway Bar Right 3664

Sway Bar Left 3665 6 1/8 X 1 Cotter Pin NB126 7 3/8-16 X 5 1/2 GR5 ZP NB575 8 Anti-Scalp Roller AS001 9 5/16-18 Nyloc Nut NB181

10 5/16-18 Serrated Flange Nut NB170 11 Lift Bracket 3738TK 12 5/16-18 X 3/4 Serr Flg Bolt NB596 13 Chute Spring CH5S 14 Grass Chute Weldement 3757TK 15 Grass Chute Mount 6030 16 5/16-18 X 8 1/2 HCC GR2 ZP NB136 17 3/8-16 X 3 HTC GR5 ZP NB164 18 3/8 SAE Washer NB272 19 3/8-16 X 2 HCC GR5 ZP NB198 20 Idler Pulley 7509 21 Clutch Rod Spring 682S 22 5/16-18 X 1 HCC GR5 ZP NB501 23 3/8-16 2-Way Lock Nut NB280 24 Deck Idler Weldement 3744TK 25 3/8-16 Nyloc Nut NB182 26 Idler Bushing 6037 27 Idler Pulley B527 28 Front Roller Bracket Assy 4018TK

Page 24

42” MOWING DECK

1012

SEE DETAIL THIS PAGE

NOT SHOWN

Roller Bracket (28) Mounting Hardware

DESCRIPTION PART # QTY

5/16-18 X 3/4 Serr Flg Bolt NB596 2

5/16-18 Serrated Flange Nut NB170 2

DECK IDLER

2425

SEE DETAIL THIS PAGE

4 5

SEE DETAIL

Page 18

DECK TENSIONER

Shown Below

Item # Description Part #

1 Deck Weldment 3762C 2 5/16-18 X 3/4 Serr Flg Bolt NB596 3 Pulley Cover 3743 4 5/16-18 Serrated Flange Nut NB170 5 Sway Bar Right 3664

Sway Bar Left 3665 6 1/8 X 1 Cotter Pin NB126 7 3/8-16 X 5 1/2 GR5 ZP NB575 8 Anti-Scalp Roller AS001 9 Seat Hinge 3808TK

10 5/16-18 Serrated Flange Nut NB170 11 Lift Bracket 3738TK 12 5/16-18 X 3/4 Serr Flg Bolt NB596 13 5/16-18 Eye Bolt NB315 14 Grass Chute Weldement 3757TK 15 Grass Chute Mount 6030 16 5/16-18 X 8 1/2 HCC GR2 ZP NB136 17 3/8-16 X 3 HTC GR5 ZP NB164 18 3/8 SAE Washer NB272 19 3/8-16 X 2 HCC GR5 ZP NB198 20 Idler Pulley 7509 21 Front Roller Bracket Assy 4018TK 22 Idler Pulley B527 23 3/8-16 2-Way Lock Nut NB280 24 Deck Idler Weldement 3764TK 25 3/8-16 Nyloc Nut NB182 26 Idler Bushing 6037

Page 25

50” MOWING DECK

SEE DETAIL THIS PAGE

SEE DETAIL

Page 18

Sway Bar Left 3665

DECK IDLER

29 22

Item # Description Part #

1 50" ZTR Deck Weldement 3766C 2 Pulley Cover (Right Side) 3769TK

Pulley Cover (Left Side) 3768TK 3 3/8-16 Nyloc Nut NB182 4 5/16-18 X 8 1/2 HCC GR2 ZP NB136 5 Sway Bar Right 3664

6 1/8 X 1 Cotter Pin NB126 7 5/16-18 X 3/4 Serr Flg Bolt NB596 8 3/8-16 Nyloc Nut NB182 9 5/16-18 Serrated Flange Nut NB170

10 Grass Chute Spring CH5S 11 Lift Bracket 3738TK 12 3/8-16 X 5 1/2 GR5 ZP NB575 13 Anti-Scalp Roller AS001 14 5/16-18 X 4 Carriage Bolt NB101 15 Grass Chute Mount 6030TK 16 Grass Chute Weldement 3773TK 17 3/8-16 Kep Nut NB205 18 3/8-16 X 3 HTC GR5 ZP NB164 19 3/8-16 X 1 1/4 GR5 ZP NB618 20 Pulley Brace 3772TK 21 3/8-16 X 3 HCC GR5 ZP NB164 22 Idler Bushing 6037 23 Idler Pulley OD-3.25" B527 24 Idler Pulley OD-2.75" 7509 25 1/4-20 X 1 Truss Head Screw NB709 26 Spring TZ2S 27 Deck Idler 3770TK 28 3/8-24 Two Way Locknut NB280 29 3/8 SAE Washer NB272 30 3/8-16 X 2 HCC GR5 ZP NB198 31 Idler Pulley 3786 32 1/4-20 Flange Nut NB524 33 1/4-20 Nylok Nut NB180 34 5/16-18 Eye Bolt NB315 35 3/8-16 HNCGR2 ZP NB212 36 3/8-16 X 1 GR5 ZP Bolt NB604 37 Idler Spacer 6040TK

Page 26

TROUBLESHOOTING

CORRECTIONCAUSESYMPTOM

ENGINE HARD TO START

ENGINE WILL NOT START OR LOSS OF POWER

1. WEAK OR DEAD BATTERY

2. AIR FILTER DIRTY

3. BAD SPARK PLUG

4. FUEL FILTER DIRTY

5. STALE OR CONTAMINATED FUEL

6. CARBURATOR OUT OF ADJUSTMENT

1. STEERING LEVERS NOT IN NEUTRAL LOCKED POSITION

2. PTO SWITCH IS ENGAGED

3. THROTTLE NOT SET PROPERLY OR NOT PROPERLY “CHOKED”

4. ENGINE FLOODED

5. DIRTY FUEL FILTER

6. DIRTY AIR FILTER

7. CONTAMINATED FUEL

8. BLOWN FUSE

9. BAD SPARK PLUG OR LOOSE PLUG WIRE

10. DIRTY ENGINE AIR SCREENS

11. WEAK OR DEAD BATTERY

12. CARBURATOR OUT OF ADJUSTMENT

13. OUT OF FUEL

14. CORRODED BATTERY TERMINALS

15. LOOSE OR DAMAGED WIRING

16. LOW OR DIRTY OIL

17. DEBRIS BUILT-UP UNDER DECK

1. REPLACE OR RECHARGE

2. CLEAN OR REPLACE

3. REPLACE SPARK PLUG

4. REPLACE FUEL FILTER

5. DRAIN AND REPLACE WITH FRESH FUEL

6. CONTACT NEAREST BRIGGS&STRATTON SERVICE REPRESENTATIVE

1. MOVE LEVERS INTO POSITION.

2. PUSH PTO SWITCH IN.

3. SEE START UP IN OPERATION SECTION.

4. WAIT SEVERAL MINUTES BEFORE STARTING

5. REPLACE WITH NEW FILTER

6. REPLACE OR CLEAN

7. DRAIN AND REPLACE WITH FRESH FUEL

8. REPLACE FUSE

9. REPLACE PLUG AND TIGHTEN PLUG WIRE

10. CLEAN ENGINE AIR SCREENS

11. REPLACE OR RECHARGE

12. CONTACT NEAREST BRIGGS&STRATTON SERVICE REPRESENTATIVE

13. REPLACE WITH FRESH FUEL

14. CLEAN TERMINALS

15. CONTACT SWISHER SERVICE REPRESENTATIVE

16. CHECK LEVEL/CHANGE OIL

17. CLEAN UNDERSIDE OF MOWER

UNIT DOES NOT TRACK STRAIGHT

1. IMPROPER AIR PRESSURE

2. TRACKING ADJUSTMENTS OUT OF ADJUSTMENT

1. CHECK ANDADJUST TIRE PRESSURE

2. SEE TRACKING ADJUSTMENT IN SERVICE SECTION

Page 27

Page 28

swisherinc.com

OWNER’S MANUAL

MODEL NO. ZT1436 ZT17542B ZT1842

“Z” SERIES

“Z” SERIES“Z” SERIES

ZERO TURN HYDROSTATIC DRIVE

ZERO TURN HYDROSTATIC DRIVEZERO TURN HYDROSTATIC DRIVE

Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found under the seat. The model number for the engine will be found on the top of the blower fan housing. All mower parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc. or your nearest Swisher dealer. All engine parts may be ordered from the nearest dealer of the

engine supplied with your mower

WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INORMATION AVAILABLE:

* PRODUCT – Zero Turn Rider (“Z” Series) * SERIAL NUMBER - _______________ * MODEL NUMBER - _______________ * ENGINE MODEL NUMBER - _______________

TYPE - _______________ * PART NUMBER WITH PAINT CODE * PART DESCRIPTION

ZT20050

SWISHER MOWER & MACHINE CO. INC.

TELEPHONE - 1-800-222-8183 FAX - 1-660-747-8650

SWISHER MOWER & MACHINE CO. INC.

1602 CORPORATE DRIVE P.O. BOX 67 WARRENSBURG, MO 64093

Swisher ZT1436 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual