
swisherinc.com
OWNER’S
MANUAL
STGUARD22
String Trimmer
Guard Kit
Starting Serial #: L313-112001
CHANGING YOUR LANDSCAPE SINCE 1945
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
PHONE 660-747-8183 FAX 660-747-8650
19041 REV 13-079
SWISHER
Made In The
USA

LIMITED WARRANTY
The manufacturer’s warranty to the original consumer
purchaser is: This product is free from defects
in materials and workmanship for a period of one (1) year from the date of purchase by the original
consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to
materials or workmanship. This warranty is subject to the following limitations and exclusions:
1) Commercial Use This product is not intended for commercial use and carries no
commercial warranty.
2) Limitation This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher that has been subject to alteration, misuse, abuse,
improper assembly or installation, shipping damage, or to normal
wear of product.
3) Exclusions Excluded from this warranty are normal wear, normal adjustments, and
normal maintenance.
In the event you have a claim under this warranty, you must return the product to an authorized
service dealer. All transportation charges, damage, or loss incurred during transportation of parts
submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you
have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The
model number, serial number, date of purchase, and the name of the authorized Swisher dealer from
whom you purchased the product will be needed before any warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not
allow the limitation of consequential damages or limitations on how long an implied warranty may
last, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty
as defined by the Magnuson-Moss Act of 1975.
2

Parts List
Before assembling your string trimmer guard please check the table
and diagram below to familiarize yourself with the parts and to
make sure no parts are missing.
Item # Part # Description
1 NB181 Nut - Nyloc 5/16-18
2 2074 Clamp
3 19040TK Weldment - Guard Mount
4 2042 Guard - String
5 NB524 Nut - Serr Flange, 1/4-20
6 NB274 Washer - SAE Flat 1/4
7 NB690 Bolt - Serr Flange, 1/4-20 X 3/4
8 26X249 Screw - .312-18 X .75
9 NB579 Washer - Fender 5/16 X 1.25
10 19038 Cage Nut - 1/4-20
3

Hardware required for assembly:
1/2” Box End Wrench
3/8” Wrench
Remove the three screws that
fasten the belt guard. Discard
these screws and set the belt
guard aside.
4

Loosely fasten the string guard to the trimmer
head assembly using clamp 2074 and two
NB181 nuts.
Make sure the holes in the brackets line up, then
securely tighten the clamp.
5

Place the belt guard back on the trimmer and fasten the two sides
using washer NB274 and bolt NB690. The bolt will engage cage
nut 19038. Fasten the front of the belt guard using washer NB274,
bolt NB690 and nut NB524. NB524 needs to be placed behind the
bracket on the trimmer head. Make sure all hardware is tightened
securely.
6

swisherinc.com
OWNER’S
MANUAL
STGUARD22
STGUARD22
String Trimmer
String Trimmer
G
uard Kit
Guard Kit
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – ________________
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER WITH PAINT CODE
* PART DESCRIPTION
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
PHONE 660-747-8183 FAX 660-747-8650
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
swisherinc.com
SWISHER
8
Made In The
USA