Swingline Stack-and-Shred, Stack-and-Shred 100X Instruction Manual
To register this product go to www.swingline.com
Pour enregistrer ce produit allez sur www.swingline.com
Para registrar este producto vaís en www.swingline.com
Swingline
™
Stack-and-Shred
™
100X Shredder
Auto+
™
Technology
Déchiqueteuse
Swingline
™
Stack-and-Shred
™
100X
à technologie
Auto+
™
Swingline
™
Stack-and-Shred
™
100X Destructora
de papel
Tecnología Auto+
™
Instruction Manual
Manuel d’utilisation
Manual de instrucciones
A
B
C
G
E
H
N
J
L
M
K
F
I
D
English 2
Français 10
Español 18
2
Introduction
Thank you for choosing this shredder from ACCO. We are sure
it will serve you well, but please take a little time to study these
instructions to ensure you get the best out of your machine.
Decal Panel (B)
• Paper Jam indicator – This means there is a Paper Jam
• Bin full / loading door open indicator – This means
the bin is full or open or the loading door is open
• Cool down indicator – This means the machine is
cooling down
Description of product parts
A
On/off switch (at rear of machine)
B
Important safety symbols
C
Manual entry slot
D
Credit card slot
E
Auto/Standby button
F
Reverse button
G
Continuous Jam Boost button
H
Loading door button
I
Loading door/lid
J
Paper stack viewing window
K
Bin full/Door open, Cool down and Paper Jam indicators
L
Pull out bin with viewing window
M
Autofeed chamber
N
Interlock actuator switch
Specifications
Sheet capacity
(Manual Entry Slot C)
Sheet capacity
(Autofeed chamber M)
Auto Shutdown
Duty cycle
Run time from cold
Volts / Hz
Amperage
Motor watts
Swingline 100X Shredder
6 sheets (75gsm)
100 sheets (75gsm)
After 2 minutes
5min ON / 30min OFF
10 minutes
120V / 60Hz
1.8 amps
200 watts
Shredder Control Panel
This means read instructions before use.
This means do not use any aerosol sprays.
This means you should be careful because long hair can
become entangled in the cutting head.
This means don’t reach into the feed opening of the
cutting head.
This means be careful of ties and other loose clothing
which could become entangled in the cutting head.
This means keep children away from shredder.
This means be careful of loose jewelry which could
become entangled in the cutting head.
This means do not shred CD/DVD.
This means do not use any oil lubricant.
ReverseForwardAuto
Important Safety Symbols
Safety First
To guard against injury, the following basic safety precautions
must be observed in the setup and use of this product.
• Electrical shock hazard. Do not open. No user serviceable
parts inside.
• Do not operate the shredder near children and pets.
• Do not use aerosol dusters or cleaners.
• Do not spray anything into the shredder.
• Do not use near water.
• Do not alter the attachment plug. The plug is congured for the
appropriate electrical supply.
• Do not operate with a damaged power supply cord or plug,
after it malfunctions, or after it has been damaged in any
manner.
• The socket-outlet should be installed near the equipment and
shall be easily accessible.
• Do not overload electrical outlets beyond capacity as this can
result in re or electrical shock.
• Unplug your shredder before moving it or when it is not in use
for an extended period of time.
• Ensure the machine is plugged into an easily accessible power
outlet, and ensure the cable is not likely to trip up a passer by.
There is an interlock actuator switch (N) located on the left of
the internal loading bay (see Fig. 4) which is designed to prevent
the shredder from operating when the loading door is open. You
must NOT under any circumstances tamper with this interlock
actuator switch. You must NOT insert any object into the interlock
actuator switch other than the interlock actuator pin on the
loading door, as to do so could activate the cutter blades.
Any attempt to repair this unit by unqualied personnel will
invalidate the warranty. Please return to supplier.
3
4
20lb / 80gsm paper
- Letter - 8.5" x 11"
- Legal - Single sheet folded in half
- A4 - 210mm x 297mm
- A5 - 148mm x 210mm
- A3 - Single sheet folded in half
1" (26 mm) and ¼" (6 mm) or smaller staples.
NOT suitable for heavy duty staples
above this size
NOT suitable for stapled documents
> 25 sheets
Capable of shredding small/medium
(max wire thickness = 0.03"/0.9 mm) paper
clips, < 0.25"/32mm length
NOT suitable for clipped documents
> 25 sheets
Paper type Staples Paper Clips
The 100X can handle the following…
100X Shredding Capability
OK to shred:
Do not shred:
The Swingline Stack and Shred
(100X) accepts fastened sheets,
however, to extend the life of
your product we recommend
that staples and paper clips be
removed prior to shredding.
- Stapled paper within 1"/
25mm from any corner
- Paper clip paper within 1"/
25mm from any corner
- Single folded sheets
- 100 sheets single side
color printed paper
- Credit cards
(through credit card slot)
- 20-50lb/80-100gsm paper
(through manual entry slot)
- 100 sheets plain paper - 100 sheets single side
printed paper
Document edge bound by
staples and paperclips
OTHER ITEMS INCLUDE:
Laminated documents
Adhesive Labels Plastic folders
Double sided color
printed paper
>25 sheets stapled or paper
clipped documents
Glossy paper
1.25"
>
¼"
>
1"
✓
✗
Auto+™ Technology
The 100X has been designed to automatically shred up to 100 sheets from the autofeed chamber and up to 6 sheets through the
manual slot. The patent pending autofeed mechanism has been designed to handle paper fastened with staples and paper clips and
to only pull a few sheets of paper into the cutting mechanism to minimise the risk of paper jams. The stack of paper does not need to
be prearranged before loading into the chamber.
To load the shredder, simply press the loading door button which automatically opens the loading door to a 45 degree angle and insert
documents. You can open the door further to 90 degrees for easier access if required. Closing the loading door will automatically start
the shredding cycle.
Fig. 1
Autofeed
Fig. 2
Manual feed
Fig. 3
Credit card
Fig. 4
Safety device
If the 100X is used continuously for over 10 minutes the
shredder may overheat and the thermometer symbol will
illuminate . Please allow the shredder to cool down. When
the shredder is ready to be used the thermometer symbol
will no longer be illuminated. If the shredder needs to cool
down while shredding, no action is needed. The shredder will
automatically restart shredding paper once it has cooled down
after periods of continuous use. All you need to do is ensure
paper is loaded into the chamber and the bin is not full when
the machine is cooling down.
Over Heating
Auto Paper Jam Bin full / Cool down
bin open /
loading
door open
Color of symbol Blue Red Red Red
Power OFF Mode Off
Auto Mode Light
Continuous Jam Boost Mode Light Light
Reverse Mode Light Light
Paper Jam Light Light
Loading Door open Light Light
Bin full or open Light Light
Motor Cool Down Required Light Light Flashing
Self cleaning of cutters Light Flashing
Sleep Mode Off
5
Lights and Icons Explained
Automatic Shredding (Fig. 1)
Press the loading door button (H) to open the loading door.
Load up to 100 sheets at a time into the autofeed chamber
(M). Do not ll above the 100 MAX level (see inside front right
of loading bay) this could damage the shredder.
Close the loading door without pressing the loading door
button. The shredder will now start automatically.
Manual Shredding (Fig. 2)
If you only have up to 6 sheets to shred, you can use the
manual entry slot (C), provided the autofeed chamber
is empty.
Credit Card Shredding (Fig. 3)
100X can shred credit cards. Switch the shredder to auto
mode (see #4 under “Operation”). Insert the credit card
into the opening on top of the manual entry slot (C). ACCO
encourages customers to recycle shredded paper. Please note
that sometimes shredded paper cannot be recycled if mixed
with credit card shards. If recycling, please separate shredded
paper and credit cards
Operation
➊ After unpacking the product, pull out the shredder bin (L).
Remove and t the recyclable paper bag (as per instructions
printed on the bag).
➋ Connect the shredder to power supply.
➌ Ensure the on/off button (A) on the back of the machine is
in the on position.
➍ To start shredding, press the central Auto button (E). This
will illuminate the blue standby symbol on the auto button.
This sets the shredder into auto mode. You are now ready
to shred.
➎ If the shredder is left in auto mode for more than 2 minutes
without being used, it will automatically turn to standby
mode to save power.
➏ The shredder will automatically operate from standby mode
when paper is inserted into the manual entry slot. Opening
either the loading door/lid (I), pull-out bin (L) or pressing
any button will return the product to auto mode.
Rare Occasions of Jamming
In the unlikely event of the shredder jamming, the 100X will
automatically reverse and forward the engine three times
to clear a jam. If after this auto jam clearance cycle the shredder still has a paper jam, the jam indicator will continue to
illuminate . Try clearing the jam using the reverse (F) and
continuous jam boost (G) buttons. If this is unsuccessful, open
the loading door (I), remove the remaining stack of paper,
then pull the jammed paper free of the cutting mechanism.
Bin/Loading Door Open
Protection Function (Fig. 4)
As an added precaution, if the bin or loading door is opened
during shredding, the shredder will stop, and the bin full / door
open indicator will glow red .
There is an interlock actuator switch (N) located on the left
of the internal loading bay which is designed to prevent the
shredder from operating when the loading door is open. You
must NOT under any circumstances tamper with this interlock
actuator switch. You must NOT insert any object into the
interlock actuator switch other than the interlock actuator
pin on the loading door, as to do so could activate the cutter
blades.
6
Bin Full
The shredder will not function when the bin is full and the bin
full symbol is illuminated red. You should empty the bin.
• Pull open the bin
• Never try to reach for any shreds hanging from cutters
• Empty bin and replace shredder bag if you are using one
• Push the empty bin back into place and press the auto button
to resume shredding.
Self-cleaning Cutters
After emptying and replacing a full bin, the shredder will run in
forward and reverse for 10-18 seconds to clear any remaining
paper from the cutter mechanism. This unique ‘self-cleaning’
mechanism is additional jam prevention technology from
Swingline.
Lubrication of the Shredder
ACCO Brands accepts no liability for product performance or
safety when lubricants are used on any part(s) of this machine.
Do not oil any part of the shredder.
The rollers on the auto-feed mechanism may become dirty over
time, please wipe clean with a dry cloth to maintain maximum
product performance.
Do not use any aerosols or sprays to either oil or clean the
shredder.
Protection Features
Protection features on the 100X include:
➊ Enclosed cutters are inside the Autofeed chamber (M) so
they are isolated from outside surfaces when in operation.
➋ Interlock switches that shut off power to the cutters when
either the loading door/lid (I) pull-out bin (L) or both are
open.
➌ Curved paper entry path for manual entry slot (C) to
reduce chances of cutters “grabbing” paper.
Reverse Function
➊ Should you wish to reverse paper out while shredding,
a reverse button ( ) has been provided for your
convenience. The jam indicator will turn to red while using
reverse mode.
➋ The reverse function will only run when the button is being
pressed. When the reverse button is released the shredder
will revert to auto mode.
Shredder Accessories
and Maintenance
We recommend using a paper bag for recycling shredded
paper. Our paper bags are made from 80% post-consumer
recycled material and are fully recyclable.
Accessory Part Number
Recycling Paper Bag 1765026
7
Warranty
Limited 5 year Cutter Warranty for 100X Shredder and
Limited 2 Year Warranty for all other Parts
ACCO Brands USA LLC, 300 Tower Parkway, Lincolnshire, IL 60069 (in Canada,
ACCO Brands Canada Inc., 5 Precidio Court, Brampton, ON L6S-6B7; and in Mexico,
ACCO Mexicana, S.A. de C.V. Av. Circuito Industrial Norte #6 Parque Industrial Lerma
52000, Lerma Edo. De México) (each, respectively, “ACCO Brands”) warrants to the
original purchaser that the cutters of this Swingline ™ Shredder 100X are free from
defects in workmanship and material under normal use and service for a period of
5 years after purchase and all other parts are free from defects in workmanship and
material under normal use and service for a period of 2 years after purchase.
ACCO Brands’ obligation under this warranty is limited to replacement or repair, at
ACCO Brands’ option, of any warranted part found defective by ACCO Brands without
charge for material or labor. Any replacement, at ACCO Brands’ option, may be the
same product or a substantially similar product that may contain remanufactured or
refurbished parts. This warranty shall be void in the following circumstances:
(i) if the product has been misused,
(ii) if the product has been damaged by negligence or accident, or
(iii) if the product has been altered by anyone other than ACCO Brands or ACCO
Brands’ authorized agents.
For warranty execution, please call:
1-800-541-0094 in the USA
1-800-263-1063 in Canada
1-800-758-6825 in Mexico
Or go to www.swingline.com.
TO THE EXTENT ALLOWED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU
OF ALL OTHER EXPRESSED WARRANTIES. REPRESENTATIONS OR PROMISES
INCONSISTENT WITH OR IN ADDITION TO THIS WARRANTY ARE UNAUTHORIZED
AND SHALL NOT BE BINDING ON ACCO BRANDS. TO THE EXTENT PERMITTED
BY APPLICABLE LAWS, ANY IMPLIED WARRANTIES (IF APPLICABLE) ARE
LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. SOME STATES
AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. TO THE
EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ACCO BRANDS BE
LIABLE FOR ANY SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL
OR SIMILAR DAMAGES, WHETHER OR NOT FORSEEABLE. SOME STATES AND
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL,
INCIDENTAL, PUNITIVE, EXEMLARY, CONSEQUENTIAL, OR SIMILAR DAMAGES, SO
THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
FOR CONSUMERS WHO HAVE THE BENEFIT OF CONSUMER PROTECTION LAWS OR
REGULATIONS IN THEIR JURISDICTION OF PURCHASE OR, IF DIFFERENT, IN THEIR
JURISDICTION OF RESIDENCE, THE BENEFITS CONFERRED BY THIS WARRANTY
ARE IN ADDITION TO ALL RIGHTS AND REMEDIES CONVEYED BY SUCH CONSUMER
PROTECTION LAWS AND REGULATIONS.
To the extent permitted by law, this warranty is not transferable and will automatically
terminate if the original product purchaser sells or otherwise disposes of the product.
This warranty gives you specic legal rights. Other rights, which vary from
jurisdiction to jurisdiction, may exist. In addition some jurisdictions do not allow (i)
the exclusion of certain warranties, (ii) limitations on how long an implied warranty
lasts and/or (iii) the exclusion or limitation of certain types of costs and/or damages,
so the above limitations may not apply.
8
TM/MC
APPLICABLE MACHINES
QUESTION ANSWER
60X 80X 100X 250X 500X
1 The shredder will not
start.
a
Check power switch on the back of the machine is turned on. (
)
Y Y Y Y Y
b
Check that the Auto button (
) has been pressed or the switch
is in the Auto position and the power switch on the back has been
turned on.
Note: The Auto button light turns off after 2 mins of non-use.
The shredder wakes up automatically if paper is in the autofeed
chamber or fed into the manual feed slot
Y Y Y
c Is the “bin door/ loading door open” indicator light red
(
)? Make sure both the loading door and the bin door are
closed.
Y Y Y Y
2 There are documents in
the autofeed chamber
but the shredder has
stopped running.
a
Is the cool-down indicator light red (
)? If so, allow the shredder
to cool down. Shredding will resume automatically after the
shredder has cooled down.
Y Y Y Y
b If the “bin door/ loading door open/bin full” indicator light is red
(
), empty the bin. Also check to see if the loading door and
bin doors are closed. Shredding will resume automatically.
Y Y Y Y
c
Is the jam indicator light red (
)? If so, the shredder was unable
to clear a jam even after the automatic jam clearance cycle. Use the
manual reverse button (
) to back out paper from the cutters.
Open the lid and remove the offending papers.
Y Y Y Y
d If there are crumpled sheets in the stack, they may not feed
properly. It is recommended that you feed them through the manual
feed slot.
Y Y Y Y Y
e If there are multiple folded sheets in the stack, unfold the sheets
before placing them back in the stack or feed through the manual
feed slot.
Y Y Y Y Y
f If there are unopened envelopes in the stack, remove them, open
the envelopes and lay the contents flat into the autofeed chamber,
unfolding any folded sheets. Envelopes can be shredded through
the manual feed slot.
Y Y Y Y Y
g Examine the rollers, if they are covered with paper dust, clean them
with a dry cloth.
Y Y Y Y Y
FOR ADDITIONAL INFORMATION ON WHAT TO SHRED THROUGH AUTO FEED AND WHAT TO SHRED
VIA MANUAL FEED SLOT, PLEASE SEE SECTION IN THE MANUAL ON ‘SHREDDING CAPABILITY’
Troubleshooting Guide for Stack-and-Shred™ 100X
Tel. 800-541-0094
www.acco.com/service
www.swingline.com/shredders
Loading...