MCRES-Micro Rev2 Installation guide
This product is intended for expert users. Please consult with a qualified technician for installation. Improper
installation may result in damage to your components. Swiftech assumes no liability whatsoever, expressed
or implied, for the use of these products, nor their installation. The following instructions are subject to
change without notice. Please visit our web site at
www.swiftech.com for updates.
Figure 1
Product Description
The MCRES-MICRO is a small form factor reservoir designed for liquid-cooled personal computers.
The device features four 1/4” NPSM (fully compatible with 1/4” BSPP/G1/4 standard) threaded ports, and is
shipped with two sets of nylon hose barbs, 3/8” and ½” to accommodate most high-flow systems.
The port usage is defined as follows:
Upper side port: “Inlet” as shown in figure 1 is the return line from the system
Lower side port: “Outlet (to pump)” shown in figure 1 should always be connected to the
pump inlet (directly if possible to facilitate filling of the system)
The fill-port located on top of the unit is used to fill it up with coolant, and sealed with a
chrome plated brass plug.
The alternate port is also sealed with a chrome plated brass plug, and can be used as:
An alternate outlet providing a straight tube routing to a pump located underneath
To feed a second pump
Copyright Swiftech 2008 – All rights reserved – Last revision date: 10-24-08
Rouchon Industries, Inc., dba Swiftech – 3700 industry ave., suite 104 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:
Swiftech@swiftech.com – URL: http://www.swiftech.com
- Information subject to change without notice
To plug-in a temperature sensor
A drain
Installation
The MCRES-MICRO can be installed in any suitable location meeting its form factor requirements. For
filling purposes, it is preferable to install the MCRES-MICRO at the highest point of the liquid cooling loop.
Fastening the device to the case: two mounting methods can be used
Various permanent mounts thru the reservoir ears or with the provided mounting hardware
as shown page 3.
Easy mount, with the provided Velcro strips. Please note that a permanent mount is
recommended for a reliable fastening of the device over time.
Recommended coolant, and prohibited fluids
We recommend using distilled water with a 5% (or up to 10%) of Swiftech’s HydrX coolant.
Use of alcohols (Alcohol Allyl, Amyl, Benzyl, Ethyl (Ethanol), Isopropyl, Methyl (Methanol), n-Butyl)
or antifreeze products containing the listed alcohols is prohibited as it will result in deterioration of
the product over-time, and will void your warranty. Resistance to Ethylene and Methylene glycol used in
antifreeze products is excellent.
Minimum Operating Level is situated at the Swiftech Logo (approximately ½” of the reservoir). The
reservoir should not be operated below this level, which could result in degradation of the system cooling
OPTIONAL COMPANION PRODUCTS
This high-polish chrome plated
brass 1/2" barb fitting is specially
designed to fit inside of the upper
fill-port when using the remote fillport fittings described to the right,
and/or to the alternate port for
various applications.
1/2" RFP-AL
Black anodized
aluminum body
1/2" RFP-CPB
High polish
chrome plated
brass body
These panel-mount 1/2" remote fill-port fitting allows users to fill-up or
refill their system from outside of the PC, or alternatively be used as a
drain; the fitting connects with 1/2" tubing to either the MCRES Micro
1/4" BSPP-1/2" RPF
Res port barb fitting or to a T-Line.
Two models are available, black anodized aluminum body, or high
polish chrome plated brass body.
Copyright Swiftech 2008 – All rights reserved – Last revision date: 10-24-08
Rouchon Industries, Inc., dba Swiftech – 3700 industry ave., suite 104 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:
Swiftech@swiftech.com – URL: http://www.swiftech.com
- Information subject to change without notice
MCRes Mi cro
Bracketry installation and
examples
6
7
4
2
DRILL ONE
.150"
(3.8MM) HOLE
ITEM NO. PART NUMBER DESCRIPTION QTY
1 BCKT1 "L" bracket 1
2 BCKT2 "U" bracket 2
3
4 91772A158-6-32X1.75
5 90760A007 6-32 Nut w/teeth washer 3
6 FW150X437X092 Rubber Washer 437X150X092 2
5
7 93286A041-WASHER
UPRIGHT MOUNT
90272A146-6-32x3-8-philips
3
1
Panel
6-32 x 3/8” Philips screw
6-32 x 1 3/4" Philips screw
zinc plated washer
Note 1: rubber washer 6
should be ins ert ed between
either si de of the reserv oi r
ear and the U bracket 2.
Reservoir ear
.
3
2
5
2
7
6
4
5
HANGING MOUNT
BACK-PANEL MOUNT
Panel
Panel
DRILL TWO
0.150" HOLES
2.00 " (50.8mm) APART
Note 2: t he 6-32 x 1 3/4” screw #4 & nut # 5 assembly is designed to protrude as little as possible in order
to r educe overall clearance neces s ary for the M icro Res assembly. It is t hus neces sary to s lightly push the nut
in order to engage it on the screw thread.
IMPORTANT DISCLOSURES
While all efforts have been made to provide the most comprehensive tutorial possible, Swiftech assumes no liability expressed or implied for any
damage(s) occurring to your components as a result of using Swiftech cooling products, either due to mistake or omission on our part in the above
instructions, or due to failure or defect in the Swiftech cooling products. WARRANTY Our products are guaranteed for 12 months from the date of
delivery to the final user against defects in materials or workmanship. During this period, they will be repaired or have parts replaced provided that:
(I) the product is returned to the agent from which it was purchased; (II) the product has been purchased by the end user and not used for hire
purposes; (III) the product has not been misused, handled carelessly, or other than in accordance with any instructions provided with respect to its
use. This guarantee does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or
damage. This guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer.
Copyright Swiftech 2008 – All rights reserved – Last revision date: 10-24-08
Rouchon Industries, Inc., dba Swiftech – 3700 industry ave., suite 104 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:
Swiftech@swiftech.com – URL: http://www.swiftech.com
- Information subject to change without notice
Loading...