Thank you for purchasing the 7950 GX2 Spacer kit. This product is intended for expert users. Please consult with a qualified
technician for installation. Improper installation may result in damage to your components. Swiftech™ assumes no liability
whatsoever, expressed or implied, for the use of this product, nor its installation. The following instructions are subject to
change without notice. Please visit our web site at www.swiftech.com for updates.
VGA compatibility
The 7950 GX2 spacer kit is only compatible with the GeForce 7950 GX2
Packing list
Quantity Part Description
3 # MF800 Male-Female 4-40 x 0.800” Standoff
1 # TA800 Pass-thru female 0.800” Standoff
1 #FF706 Female-Female 4-40 x 0.706” Standoff
1 Screw 4-40 x Philips screw
1 Ramsink 1 MC14 Ramsink
1 7950EB Extended PCB
Installation Guidelines
Step-by-step
First step
Turn the graphics card over
and remove the one screw
holding to the PCI bracket
Step 2
Turn the graphics card over
and remove all 4 screws
shown above (keep them; you
Step 3
Carefully separate the 2 cards.
are going to reuse them).
Step 4
Remove the stock PCB.
Step 5
Install Swiftech’s extended PCB
provided with your kit.
Step 6
Insert the Female pass-thru
standoff between the card and the
PCI bracket
Copyright Swiftech 2006 - All rights reserved - Last revision date: 10-13-06 - One or more Patents Pending
Rouchon Industries, Inc., dba Swiftech - 3700 Industry avenue, suite 104, Lakewood CA 90712- Toll free (US) 866-857-9438 Fax 562-595-8769 -
E Mail: help@swiftech.com - URL: http://www.swiftech.com - Information subject to change without notice
Step 7
Insert the provided 4-40 screw
thru the card and into the
Female pass-thru standoff.
Step 8
Screw the female-female
threaded standoff over the PCI
bracket
Step 9
Screw all 3 Male-female
standoffs to those of the card.
You now have 4 extended
standoffs, and are ready to
complete the installation in the
next two steps.
Step 10
Install the provided MC14
Ramsink on the SLi chip of the
main board as shown above
Step 11
Assemble the 2 cards. Make sure
that the PCB is correctly aligned.
Step 12
Fasten the 4 screws at the back
of the graphics card.
You’re done!
IMPORTANT DISCLOSURES
While all efforts have been made to provide the most comprehensive tutorial possible, Swiftech assumes no liability expressed or implied for any
damage(s) occurring to your components as a result of using Swiftech cooling products, either due to mistake or omission on our part in the enclosed
instructions, or due to failure or defect in the Swiftech cooling products.
WARRANTY
Our products are guaranteed for 12 months from the date of delivery to the final user against defects in materials or workmanship. During this period, they
will be repaired or have parts replaced provided that: (I) the product is returned to the agent from which it was purchased; (II) the product has been
purchased by the end user and not used for hire purposes; (III) the product has not been misused, handled carelessly, or other than in accordance with any
instructions provided with respect to its use. This guarantee does not confer rights other than those expressly set out above and does not cover any claims
for consequential loss or damage. This guarantee is offered as an extra benefit and does not affect your statutory rights as a consumer.
Copyright Swiftech 2006 - All rights reserved - Last revision date: 10-13-06 - One or more Patents Pending
Rouchon Industries, Inc., dba Swiftech - 3700 Industry avenue, suite 104, Lakewood CA 90712- Toll free (US) 866-857-9438 Fax 562-595-8769 -
E Mail: help@swiftech.com - URL: http://www.swiftech.com - Information subject to change without notice
Loading...