Help Desk / Support Details
Swann Technical Support
All Countries E-mail:
Telephone Helpdesk
UNITED STATES toll free
877-274-3695
(Sun-Thurs, 2pm-10.30pm PST)
800-627-2799
(Mon-Fri, 9am-1pm PST)
USA Exchange & Repairs
562-777-2551
(Mon-Fri, 9am-5pm PST)
AUSTRALIA toll free
1300 13 8324
(Mon-Fri, 9am-5.30pm Aus EST)
International
+61 3 8412 4610
(Mon-Fri, 9am-5.30pm Aus EST)
See http://www.worldtimeserver.com for information on different time
zones and the time in Melbourne Australia compared to your local time.
Warranty Information
English
tech@swann.com.au
Night Hawk
Wireless Outdoor Camera
With Night Vision
If this device does not work when you first plug it in,
do not take it back to the store.
Swann Communications warrants this product against defects in workmanship and material for
a period of one ( ) year from it’s original purchase date. You must present your receipt as
proof of date of purchase for warranty validation. Any unit which proves defective during the
stated period will be repaired without charge for parts or labour or replaced at the sole
discretion of Swann. The repair or replacement will be warranted for either ninety days or the
remainder of the original one year warranty period, whichever is longer. The end user is
responsible for all freight charges incurred to send the product to Swann’s repair centres. The
end user is responsible for all shipping costs incurred when shipping from and to any country
other than the country of origin. The warranty does not cover any incidental, accidental or
consequential damages arising from the use of or the inability to use this product. Any costs
associated with the fitting or removal of this product by a tradesman or other person or any
other costs associated with its use are the responsibility of the end user. This warranty applies
to the original purchaser of the product only and is not transferrable to any third party.
Unauthorised end user or third party modifications to any component or evidence of misuse
or abuse of the device will render all warranties void.
1
www.swannsecurity.com
8
Contact the Swann Helpdesk using our fast e-mail service
tech@swann.com.au
or call us on one of the Toll-Free
numbers shown on the back cover of this booklet.
Most problems can be quickly and easily fixed with a simple
e-mail or a quick chat with one of our friendly technical staff.
(Toll-Free available in the US and Australia only)
Note: Wireless Networks (WiFi) may interfere with and/or experience interference caused by
the transmitterin this unit. Changing the receiver to another channel/frequency or setting the Wireless
Network (i.e. Wireless Access Point) to a frequency further away from the camera’s set frequency can
alleviate this problem. Consult the documentation of your Wireless LAN device for information on how
to change the transmission frequency. These cameras work with most wireless camera receivers that
support 2414MHz, 2432MHz,
Installation Guide
Index
Technical Specifications
Introduction
Your Night Hawk package comes with
Setting up your system
Camera Features
Receiver Features
Changing the channel on the Night Hawk Camera
Important Information about this product
Troubleshooting, Hints & Tips
Warranty Information
Technical Specifications
Help Desk / Support Details
2
2
3
4
4
5
5
6
7
7
Back Cover
Introduction
The Swann Night Hawk Camera Package incorporates the latest in advanced technology. We feel
confident that you will be pleased with the quality and features of this product.
The Swann Night Hawk Camera allows you to transmit pictures and sound with ease. As the radio
waves it uses have a frequency of 2.4GHz, they can be received within a radius of up to 328ft/100
m in open line of sight. The Night Hawk Camera Receiver works with other Swann cameras to
allow you to have the option of using different frequencies for different locations and conditions to
ensure that you have the best possible image quality for your situation.
Please note: The Swann Night Hawk Camera broadcasts video in the public domain. The
Night Hawk 2.4GHz Transmitter
Available Channels: 4 Channels in 2.4Ghz frequency band*
RF Output Power: FCC, CE and C-tick compliant
Operating Power: 8V DC
Power Consumption: 100mA
Size: / ”x / ”x1” (22x22x25mm)
Antenna: Omni-directional
Transmitting Range: Up to 328ft ~ 100M line of sight
Weight: ¾oz ~ 20 grams
Operating Temperature: 0° - 50°C (32° - 122°F)
77
88
Night Hawk 2.4GHz Receiver
Frequency: 4 Channels in 2.4 Ghz frequency band*
Video input/output: 1Vp-p/75ohm
Audio input / output: 0.8V / 600 ohm
Antenna: 60 degree directional
Audio Bandwidth: 50 - 17000 Hz
Operating Power: 8V-12V DC
Power Consumption: 180mA
Size: 6”x3½”x1 / ” 150 x 88 x 40mm
*The Night Hawk Camera uses the following frequencies for the 4 channels:
Channel ( 2414MHz), Channel (2432MHz), Channel (2450MHz) and Channel (2468MHz).
123 4
5
()
8
video signal is not encrypted and could potentially be viewed by anyone with a similar 2.4GHz
receiver unit. Please keep this in mind when positioning and using any wireless camera
equipment.
This Package Comes With ...
• 1 x Night Hawk Color Camera with built in 2.4GHz Transmitter with Stand
• 1 x Night Hawk 4 channel 2.4GHz Receiver
• 2 x Mains Power Adaptor (8V for use with Night Hawk Camera and Receiver)
• 1 x Battery Snap Adaptor (For use with Night Hawk Camera, 9V batteries not included)
• RCA A/V Cable
• This Instruction Sheet
If any of these items are missing, please contact your retailer.
FCC NOTICE
This device complies with Part 15 of FCC Rules.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
Including interference that may cause undesired operation.
2 7
Night Hawk CMOS Colour Camera
Sensor: 1/3”(8.5mm) Colour CMOS
Horizontal Resolution: 380 TV lines
Auto Electronic Exposure: 1/60 - 1/15000 sec.
Minimum Illumination: 1.5 Lux @ f1.2 LEDs inactive
0 Lux @ f1.2 LEDs active
Signal to Noise Ratio: >48dB
Board Lens: / ” ~ 5.6mm
View Angle: 60 degrees
Size: / x / ” ~16mm x 18mm, board lens
Video System: PAL 50Hz (Australia, UK/Europe),
Automatic Exposure / Gain / White balance/IR LED activation
7
32
523
832
NTSC 60Hz (USA and Canada)
Troubleshooting your Night Hawk Camera Setting Up Your System
Poor Picture:
Camera or Receiver. Change the location of the Camera, or use a different Camera in the location
experiencing interference that is on a different channel. In some cases interference may be caused by
another device on a similar frequency to the channel you are using. Change to one of the other channels
and check the signal quality again.
Lines only - no clear picture:
equipment operating close by ie; Cordless Telephones, Wireless Baby Monitors, Wireless LAN
equipment etc. Make sure the Receiver is on the correct channel for the particular camera.
Picture ghosting or interference:
telephones and Microwave ovens operate on or near the 2.4GHz frequency. If you receive interference
from such an appliance, try moving the Camera or Receiver to location further away from the appliance
or in the event of interference from a Wireless LAN device,
try changing the Wireless LAN to a different channel to improve the signal quality.
No picture
Receiver is not plugged into the Audio Out socket. Make sure the Receiver is on the correct channel.
Check to ensure the camera is plugged in and has power (cup your hands around the camera and you
should see a faint red glow from the IR LEDs). Check that the channel on the receiver is the set to the
same as the camera you wish to view.
We, Swann Communications of 10612 Shoemaker Avenue, Bldg A, Santa Fe Springs, CA 90670 USA,
declare under our sole responsibility that the product:
This product meets the requirement specified in Part 15 of FCC Regulation. Operation rests with the
following two conditions:
(1) The equipment should not cause any harmful interference;
(2) The equipment must receive and process any interference, including any possible interference
caused by operation mistakes. After testing the product, we confirm that it complies with the provision
for class C digital equipment in the 15th part in FCC regulation; and the receiver complies with the
limitation for class B digital equipment in Part 15 of FCC regulation. The product generates, applies and
emits radio waves. It might cause harmful interferences to wireless communication if not be installed
and used following the description of the manual. The product may interference in residential area, and
the customer should take remedies to eliminate the interference at their own costs. If the product
causes any harmful interference to wireless equipment of disturbs the receiving of TV signals (it can be
identified by turning on and off the product), you can solve the trouble by following methods:
(1) Re-adjust the product or put it in another place;
(2) Extend the distance between the equipment interfered and the product; and
(3) Refer to dealers or experienced radio electrician for help
This product complies with standards including ow oltage evice Directive 73/23/EEC;
Directive 89/336/EEC and Directive 1999/5/EC. It passed the subject tests by authority
concerned and it authorized to bear mark.
Realign antennas until image quality improves, slightly adjust the position of the Night Hawk
Check to confirm there is no microwave oven or other 2.4GHz
Some home appliances such as Wireless LANs, 2.4GHz portable
: check the receiver to confirm it is turned ON and make sure the A/V connection of the
FCC Notice
SW231-WOC
CE Notice
LV D
R&TTE
CE
EMC
Camera with Stand
External antenna
Receiver Features
Monitor or TV
Camera Power Adaptor (8V)
Receiver
Active
Leds
Normal
CH1
CH2
CH3
CH4
SEL
Channel
Channel
Selector
Button
The Camera features an omni-directional antenna which is most effective when use
in the UPRIGHT position.
1)
Connect both the Camera and the Receiver to their respective power adaptors.
2)
Connect the Receiver to the equipment you wish to view the camera on (monitor, AV TV,
VCR, DVR etc) using the supplied A/V-RCA cable.
3) After connecting both the Night Hawk Camera and the Receiver make sure the receiver
is switched to the same channel as the camera. channel 1.
Press the button on the receiver until the LED for is lit. If the channel LEDs flash and
SEL Ch1
the receiver scans through all 4 channels, switch the Loop/Normal selector at the back of the
receiver to . Obtain the best picture by adjusting the position of the Night Hawk
camera and Receiver unit to suit. Try slightly different locations of either unit for optimum
results.
If you are mounting the camera to a ceiling or eave, unscrew the camera stand from the
4)
camera body and carefully screw it into position on the top side of the camera using the two
holes that are provided or the picture will appear on your screen upside down.
To Audio and
Video IN
Audio / Video Out
Receiver
DC Socket
Loop / Normal Switch
By default the camera is set to
Power Adaptor
36
Camera Features
Changing the Channel on the Night Hawk Camera
1. Omni-directional Antenna
2. Infra-red LEDs
3. Detachable Camera Stand
4. Microphone (enclosed in socket)
5. Power Cable & DC Power
Receiver Features
External antenna
Receiver
CH1
Active
CH2
Channel
CH3
Leds
CH4
SEL
Channel
Selector
Button
4
Audio / Video Out
DC Socket
Loop / Normal Switch
1
To Audio and
Video IN
Receiver
Power Adaptor
2
3
4
5
MonitororTV
The Night Hawk Cameras can be switched to any of four frequencies to assist in avoiding
interference. Please see the illustration below for frequency settings. Unscrew the front of the
camera case to gain access to the channel switch. To change the frequency/channel on the receiver,
press the SEL button on top of the receiver to cycle through the channels. You can also switch the
Loop/Normal switch to Loop, which will allow the receiver to switch through all four channels
automatically. The lit LED indicates which channel is currently selected.
12
Front view of Switch Block (note the numbers1&2
indicate the left side of the switch)
By changing these switch settings, the frequency that the
Camera transmits on . Once you have set the channel
on the Camera, select the same channel on the receiver. If you
experience interference try a different channel.
Do not set two Cameras to the same channel or they
will interfere with each others signal.
changes
Channel & Frequency settings
12
12
12
12
Channel 1
Both switches Right
2414MHz
Channel 2
Top Left & Bottom Right
2432MHz
Channel 3
Top Right & Bottom Left
2450MHz
Channel 4
Both switches Left
2468MHz
Important Information About This Product
• Best Results are achieved where there is a clear “line of sight” between the
Camera/Transmitter and Receiver.
• Interference from certain electronic equipment or the moving human body can also affect the
range obtainable.
• Please test all devices before final installation because transmission quality can often be
improved by moving the components slightly.
• To avoid the risk of damage to Night Hawk Camera Pack, use only the supplied
power adaptors.
• Beware of humid locations. Water droplets or spray may damage the receiver unit. If
condensation does occur, do not use the equipment until it has dried out.
• Do not cut the DC power cable of the Night Watch Camera to fit with another power
source. This may result in damage to the Night Watch Camera & any unauthorised
modifications will void your warranty.
IMPORTANT: Due to the power consumption requirements of this product, we highly
recommend the use of a 9 volt battery only for short term portable use.
5
Loading...