User Manual
P Line Touch Panel
Part Number: 80860.761
Version: 7
Date: 2014-03-12
Valid for: TP057ZTV
TP057GTV
TP070ZTW
TP070GTW
TP090ZTW
TP090GTW
TP105ZTS
TP105GTS
TP121ZTS
TP121GTS
TP121ZTM
TP121GTM
TP150ZTX
TP150GTX
TP154ZTM
TP154GTM
P Line Touch Panel
Version Date Modifications
1 2010-05-18 First Edition
2 2010-10-15 TP070ZTW, TP090ZTW, TP121ZTS added.
3 2011-09-13 TP057ZTV, TP121ZTM, TP151ZTX added.
4 2012-12-12 TP154ZTM, TP070GTW, TP090GTW, TP121GTM,
TP154ZTM added.
5 2013-05-15 RS232 / RS485 COM ports updated.
6 2013-08-08 TP057ZTV, TP121GTS, TP150GTX added.
7 2014-03-12 TP105ZTS, TP105GTS added.
This manual, including all illustrations contained herein, is copyright protected. Use of this manual by any third
party in departure from the copyright provision is forbidden. No part of this manual may be reproduced, translated or electronically or photographically archived or altered without the express written consent from Sütron
electronic GmbH. Violations shall be cause for damage liability.
Sütron electronic reserves the right to make any changes that contribute to technical improvement.
P Line Touch Panel Overall Table of Contents
3
Overall Table of Contents
1 Important Notes .......................................................................................................... 7
1.1 Symbols ....................................................................................................... 7
1.2 Safety Notes ................................................................................................ 7
1.3 Intended Use................................................................................................ 8
1.4 Target Group................................................................................................ 8
2 Installation and Commissioning .................................................................................. 9
2.1 Unpacking the Device .................................................................................. 9
2.2 Mounting the Device .................................................................................... 9
2.2.1 Front Panel Dimensions ....................................................................... 10
2.2.1.1 TP057ZTV / TP057GTV .............................................................................................. 10
2.2.1.2 TP070ZTW / TP070GTW ............................................................................................ 11
2.2.1.3 TP090ZTW / TP090GTW ............................................................................................ 12
2.2.1.4 TP105ZTS / TP105GTS .............................................................................................. 13
2.2.1.5 TP121ZTS / TP121GTS .............................................................................................. 14
2.2.1.6 TP121ZTM / TP121GTM .............................................................................................15
2.2.1.7 TP150ZTX / TP150GTX .............................................................................................. 16
2.2.1.8 TP154ZTM / TP154GTM .............................................................................................17
2.2.2 Mounting Cutout ................................................................................... 18
2.2.2.1 TP057ZTV / TP057GTV .............................................................................................. 18
2.2.2.2 TP070ZTW / TP070GTW ............................................................................................ 19
2.2.2.3 TP090ZTW / TP090GTW ............................................................................................ 20
2.2.2.4 TP105ZTS / TP105GTS .............................................................................................. 21
2.2.2.5 TP121ZTS / TP121GTS .............................................................................................. 22
2.2.2.6 TP121ZTM / TP121GTM .............................................................................................23
2.2.2.7 TP150ZTX / TP150GTX .............................................................................................. 24
2.2.2.8 TP154ZTM / TP154GTM .............................................................................................25
2.2.3 Side View, Mounting Depth .................................................................. 26
2.2.3.1 TP057ZTV / TP057GTV .............................................................................................. 26
2.2.3.2 TP070ZTW / TP070GTW ............................................................................................ 27
2.2.3.3 TP090ZTW / TP090GTW ............................................................................................ 28
2.2.3.4 TP105ZTS / TP105GTS .............................................................................................. 29
2.2.3.5 TP121ZTS / TP121GTS .............................................................................................. 30
2.2.3.6 TP121ZTM / TP121GTM .............................................................................................31
2.2.3.7 TP150ZTX / TP150GTX .............................................................................................. 32
2.2.3.8 TP154ZTM / TP154GTM .............................................................................................33
2.3 Connecting the Device............................................................................... 34
2.3.1 Supply Voltage...................................................................................... 34
2.3.2 Grounding ............................................................................................. 35
2.4 Switching On.............................................................................................. 36
2.4.1 Cockpit.................................................................................................. 36
2.4.1.1 Menu Structure ............................................................................................................37
2.4.1.2 Settings and Functions ................................................................................................37
2.4.1.2.1 Language Selection............................................................................................... 37
2.4.1.2.2 Date and Time....................................................................................................... 38
2.4.1.2.3 Administration........................................................................................................38
Overall Table of Contents P Line Touch Panel
4
2.4.1.2.4 Network ................................................................................................................. 38
2.4.1.2.5 Password .............................................................................................................. 39
2.4.1.2.6 Display .................................................................................................................. 39
2.4.1.2.7 Write Filter............................................................................................................. 39
2.5 Identification ............................................................................................... 41
3 Control and Display Elements................................................................................... 43
3.1 Touch Screen............................................................................................. 43
3.2 Display ....................................................................................................... 43
4 Interfaces of the Device ............................................................................................45
4.1 Ethernet...................................................................................................... 46
4.1.1 Pin Assignment ..................................................................................... 46
4.1.2 Cable..................................................................................................... 46
4.1.3 Diagnosis .............................................................................................. 47
4.2 USB............................................................................................................ 47
4.2.1 Cable..................................................................................................... 47
4.3 Serial Interfaces ......................................................................................... 48
4.3.1 RS-422 / RS-485 (X14)......................................................................... 49
4.3.1.1 Pin Assignment............................................................................................................ 49
4.3.1.2 Termination.................................................................................................................. 50
4.3.1.3 Transmitter Control......................................................................................................51
4.3.1.4 Diagnosis..................................................................................................................... 51
4.3.2 RS232 (X15) ......................................................................................... 52
4.3.2.1 Pin Assignment............................................................................................................ 52
4.3.2.2 Diagnosis..................................................................................................................... 52
4.4 Field Bus Interfaces ................................................................................... 53
4.4.1 CAN (X12, X13) .................................................................................... 53
4.4.1.1 Pin Assignment............................................................................................................ 54
4.4.1.2 Cable ........................................................................................................................... 54
4.4.1.3 Termination.................................................................................................................. 55
4.4.1.4 Diagnosis..................................................................................................................... 55
4.5 Memory Card ............................................................................................. 56
4.5.1 Inserting the memory card .................................................................... 56
4.5.2 Ejecting the memory card ..................................................................... 56
4.6 Shielding D-SUB Connectors..................................................................... 57
5 Maintenance and Servicing....................................................................................... 59
5.1 Maintenance Interval.................................................................................. 59
5.2 Front Panel................................................................................................. 59
5.3 Fuse ........................................................................................................... 59
5.4 Battery........................................................................................................ 59
5.4.1 Changing the Battery ............................................................................ 60
5.4.2 Battery Disposal.................................................................................... 61
P Line Touch Panel Overall Table of Contents
5
6 Technical Data.......................................................................................................... 63
6.1 General ...................................................................................................... 63
6.2 TP057ZTV.................................................................................................. 65
6.3 TP057GTV ................................................................................................. 67
6.4 TP070ZTW................................................................................................. 69
6.5 TP070GTW ................................................................................................ 71
6.6 TP090ZTW................................................................................................. 73
6.7 TP090GTW ................................................................................................ 75
6.8 TP105ZTS.................................................................................................. 77
6.9 TP105GTS ................................................................................................. 79
6.10 TP121ZTS.................................................................................................. 81
6.11 TP121GTS ................................................................................................. 83
6.12 TP121ZTM ................................................................................................. 85
6.13 TP121GTM ................................................................................................ 87
6.14 TP150ZTX.................................................................................................. 89
6.15 TP150GTX ................................................................................................. 91
6.16 TP154ZTM ................................................................................................. 93
6.17 TP154GTM ................................................................................................ 95
7 Ordering Data ........................................................................................................... 97
A Index ......................................................................................................................... 99
Overall Table of Contents P Line Touch Panel
6
P Line Touch Panel Important Notes
7
1 Important Notes
1.1 Symbols
The symbols in this manual are used to draw your attention on notes and dangers.
1.2 Safety Notes
– Read this manual carefully before using the operating device. Keep this man-
ual in a place where it is always accessible to all users.
– Proper transportation, handling and storage, placement and installation of this
product are prerequisites for its subsequent flawless and safe operation.
– This user manual contains the most important information for the safe opera-
tion of the device.
– The user manual, in particular the safety notes, must be observed by all per-
sonnel working with the device.
– Observe the accident prevention rules and regulations that apply to the oper-
ating site.
– Installation and operation must only be carried out by qualified and trained
personnel.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER
This indicates a hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
This indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION
This indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
NOTICE
This symbol together with the signal word NOTE and the accompanying text
alert the reader to a situation which may cause damage or malfunction to the
device, hardware/software, or surrounding property.
This symbol and the accompanying text provide the reader with additional information or refer to detailed sources of information.
Important Notes P Line Touch Panel
8
1.3 Intended Use
– The device is designed for use in the industry.
– The device is state-of-the art and has been built to the latest standard safety
requirements. However, dangerous situations or damage to the machine itself
or other property can arise from the use of this device.
– The device fulfills the requirements of the EMC directives and harmonized Eu-
ropean standards. Any modifications to the system can influence the EMC behavior.
1.4 Target Group
The use of products described in this manual is oriented exclusively to:
– Qualified electricians or persons instructed by them, who are familiar with ap-
plicable standards and other regulations regarding electrical engineering and,
in particular, the relevant safety concepts.
– Qualified application programmers and software engineers, who are familiar
with the safety concepts of automation technology and applicable standards.
NOTICE: Radio Interference
This is a class A device. This device may cause radio interference in residential
areas. In this case, the user may be required to introduce appropriate countermeasures, and to bear the cost of same.
P Line Touch Panel Installation and Commissioning
9
2 Installation and Commissioning
2.1 Unpacking the Device
Unpack all parts carefully and check the contents for any visible damage in transit.
Also check whether the shipment matches the specifications on your delivery
note.
If you notice damages in transit or discrepancies, please contact us immediately.
2.2 Mounting the Device
The device can be easily and quickly mounted from the rear of the device. A panel
thickness of 1 mm to 6 mm (0.039" to 0.236") is permitted for proper mounting.
1. Insert the device in the mounting cutout from the front.
Figure 2-1 Mounting the device using a mounting bracket
2. Insert the mounting brackets into the appropriate openings (figure 1) and pull
the brackets downwards until they lock in place (2).
3. Fasten the device into position using the threaded pins (3).
NOTICE: Damage
When installing the device, leave a gap of at least 30 mm (1.181") around the
device to ensure sufficient air circulation.
NOTICE: Damage
When the operating device is installed horizontally, please note that additional
sources of heat beneath the operating device may result in heat accumulation.
Make sure to allow sufficient heat dissipation!
Please observe the permissible temperature range specified in the technical
data of the user manual when operating the device.
NOTICE: Damage
In order to ensure the degree of protection specified in the technical data, always make sure that the seal lies flat against the mounting surface and the
threaded pins of the mounting brackets are tightened uniformly to a maximum
torque of 1 Nm.
Installation and Commissioning P Line Touch Panel
10
2.2.1 Front Panel Dimensions
2.2.1.1 TP057ZTV / TP057GTV
Figure 2-2 TP057ZTV / TP057GTV
P Line Touch Panel Installation and Commissioning
11
2.2.1.2 TP070ZTW / TP070GTW
Figure 2-3 TP070ZTW / TP070GTW
Installation and Commissioning P Line Touch Panel
12
2.2.1.3 TP090ZTW / TP090GTW
Figure 2-4 TP090ZTW / TP090GTW
P Line Touch Panel Installation and Commissioning
13
2.2.1.4 TP105ZTS / TP105GTS
Figure 2-5 TP105ZTS / TP105GTS
Installation and Commissioning P Line Touch Panel
14
2.2.1.5 TP121ZTS / TP121GTS
Figure 2-6 TP121ZTS / TP121GTS
P Line Touch Panel Installation and Commissioning
15
2.2.1.6 TP121ZTM / TP121GTM
Figure 2-7 TP121ZTM / TP121GTM
Installation and Commissioning P Line Touch Panel
16
2.2.1.7 TP150ZTX / TP150GTX
Figure 2-8 TP150ZTX / TP150GTX
P Line Touch Panel Installation and Commissioning
17
2.2.1.8 TP154ZTM / TP154GTM
Figure 2-9 TP154ZTM / TP154GTM
Installation and Commissioning P Line Touch Panel
18
2.2.2 Mounting Cutout
2.2.2.1 TP057ZTV / TP057GTV
Figure 2-10 TP057ZTV / TP057GTV
A Mounting Cutout
B Front Panel
P Line Touch Panel Installation and Commissioning
19
2.2.2.2 TP070ZTW / TP070GTW
Figure 2-11 TP070ZTW / TP070GTW
A Mounting Cutout
B Front Panel
Installation and Commissioning P Line Touch Panel
20
2.2.2.3 TP090ZTW / TP090GTW
Figure 2-12 TP090ZTW / TP090GTW
A Mounting Cutout
B Front Panel
P Line Touch Panel Installation and Commissioning
21
2.2.2.4 TP105ZTS / TP105GTS
Figure 2-13 TP105ZTS / TP105GTS
A Mounting Cutout
B Front Panel
Installation and Commissioning P Line Touch Panel
22
2.2.2.5 TP121ZTS / TP121GTS
Figure 2-14 TP121ZTS / TP121GTS
A Mounting Cutout
B Front Panel
P Line Touch Panel Installation and Commissioning
23
2.2.2.6 TP121ZTM / TP121GTM
Figure 2-15 TP121ZTM / TP121GTM
A Mounting Cutout
B Front Panel
Installation and Commissioning P Line Touch Panel
24
2.2.2.7 TP150ZTX / TP150GTX
Figure 2-16 TP150ZTX / TP150GTX
A Mounting Cutout
B Front Panel
P Line Touch Panel Installation and Commissioning
25
2.2.2.8 TP154ZTM / TP154GTM
Figure 2-17 TP154ZTM / TP154GTM
A Mounting Cutout
B Front Panel
Installation and Commissioning P Line Touch Panel
26
2.2.3 Side View, Mounting Depth
2.2.3.1 TP057ZTV / TP057GTV
Figure 2-18 TP057ZTV / TP057GTV
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
P Line Touch Panel Installation and Commissioning
27
2.2.3.2 TP070ZTW / TP070GTW
Figure 2-19 TP070ZTW / TP070GTW
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
Installation and Commissioning P Line Touch Panel
28
2.2.3.3 TP090ZTW / TP090GTW
Figure 2-20 TP090ZTW / TP090GTW
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
P Line Touch Panel Installation and Commissioning
29
2.2.3.4 TP105ZTS / TP105GTS
Figure 2-21 TP105ZTS / TP105GTS
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
Installation and Commissioning P Line Touch Panel
30
2.2.3.5 TP121ZTS / TP121GTS
Figure 2-22 TP121ZTS / TP121GTS
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
P Line Touch Panel Installation and Commissioning
31
2.2.3.6 TP121ZTM / TP121GTM
Figure 2-23 TP121ZTM / TP121GTM
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
Installation and Commissioning P Line Touch Panel
32
2.2.3.7 TP150ZTX / TP150GTX
Figure 2-24 TP150ZTX / TP150GTX
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
P Line Touch Panel Installation and Commissioning
33
2.2.3.8 TP154ZTM / TP154GTM
Figure 2-25 TP154ZTM / TP154GTM
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
Installation and Commissioning P Line Touch Panel
34
2.3 Connecting the Device
2.3.1 Supply Voltage
The supply voltage is supplied via pin strip X1. A suitable socket strip is supplied.
Refer to the technical data for the permissible supply voltage of the operating device.
Connector in the operating device: 3 pin pin strip
Use the following procedure to connect the device to the supply voltage:
1. Strip approx. 30 mm (1.181") off the outer cable sheath and approx. 5 mm
(0.197") off the wires.
Figure 2-26 Preparing the cable
2. Fit the wires with wire end ferrules and connect the wires to the socket strip.
3. Plug the socket strip onto pin strip X1.
4. Secure the socket strip in place with a screw-type locking to prevent it from
slipping out.
The device has reverse polarity protection. In case of wrong polarity, the device
will not operate.
This is a protection class I device. For safe operation, safety extra-low voltage
(SELV) in accordance with DIN EN 61131 must be used for the supply voltage.
Table 2-1 Pin assignment supply voltage
Pin Designation Function
1 Noiseless ground / functional earth ground (FE)
2 0 V Supply voltage 0 V (GND)
3 24 V Supply voltage 24 V
NOTICE: Damage
Cables with finely stranded copper conductors with a minimum cross-section of
0.75 mm² (18 AWG) and a maximum cross-section of 2.5 mm² (14 AWG) must
be used for the supply voltage.
You must adhere to the following torques at the connector:
Screw connection of terminal blocks: 0.22 Nm (minimal) to 0.25 Nm (maximum)
Screw flange: 0.3 Nm (maximum)
DANGER: Hazardous voltages
Hazardous voltages can exist inside electrical installations that can pose a danger to humans. Coming in contact with live parts may result in electric shock!
P Line Touch Panel Installation and Commissioning
35
2.3.2 Grounding
The grounding is performed - depending on the type of device - with a slip-on
sleeve (noiseless ground / functional earth ground) or a ring cable lug (protective
ground).
1. Strip approx. 5 mm (0.197") off the wires.
2. Fit the stripped wires - depending on the type of device - with a slip-on sleeve
or a ring cable lug.
3. Plug the slip-on sleeve on the flat tab or mount the ring cable lug with the nut
to the threaded bolt.
Figure 2-27 Noiseless ground / protective ground
NOTICE: Damage
A separate copper conductor must always be provided for the grounding. The
conductor must have a minimum cross-section of 1.5 mm² (16 AWG) and must
be kept as short as possible.
You must adhere to a maximum torque of 1 Nm at an protective grounding on
the threaded bolt.
Installation and Commissioning P Line Touch Panel
36
2.4 Switching On
When switching on the operating system loads. The interface for SD/SDHC cards
is available for applications and other data.
2.4.1 Cockpit
The operating device allows you - by starting the cockpit during the startup phase
- to make changes to the device configuration.
Start cockpit at system
startup
To start the cockpit, do the following:
1. Wait during the startup phase until the following dialog is displayed:
Figure 2-28 Cockpit startup phase
2. Press the button to start the cockpit before the progress bar is down.
You can customize the language of the cockpit interface at the language menu
item.
3. Press the button Language Selection.
4. Select the desired language.
5. Confirm your selection with the green check.
Using desktop icon to
start cockpit
You can start the cockpit via the desktop icon at already started operating devices
with active desktop:
1. Briefly press twice on the desktop icon.
2. Press the button to start the cockpit before the progress bar is down.
You can customize the language of the cockpit interface at the language menu
item.
3. Press the button Language Selection.
4. Select the desired language.
5. Confirm your selection with the green check.
P Line Touch Panel Installation and Commissioning
37
2.4.1.1 Menu Structure
2.4.1.2 Settings and Functions
2.4.1.2.1 Language Selection
You can customize the language of the cockpit interface at the language menu
item.
1. Select the desired language.
2. Confirm your selection with the green check.
Start
Cockpit
Normal
Language Selection
English
German
Date and Time
Administration
Information
Network
IP Address
WINS / DNS
Device Name
SNTP
Password
Display
Brightness
Orientation
Calibrate Touch
Write Filter
EWF
FBWF
HORM
Some settings are password-protected. The default password is "+-+-".
Installation and Commissioning P Line Touch Panel
38
2.4.1.2.2 Date and Time
You set up date, time and time zone via the Date and Time menu item.
2.4.1.2.3 Administration
The Administration menu shows device information.
Information The following informations are displayed:
– Device type
– Hardware version,
– Serial number,
– Image name,
–Image date,
– Operating system.
2.4.1.2.4 Network
You can configure the network settings with the Network menu item.
IP Address Use Dynamic IP (DHCP)
The network configuration is automatically obtained from the DHCP server.
Confirm your selection with the green check.
Use Static IP
Manually assign an ip address, subnet mask and gateway of the operating device.
Confirm your selection with the green check.
WINS / DNS Optionally, enter the addresses for the WINS / DNS server.
Confirm your selection with the green check.
Device Name You can define a device name with a maximum of 15 characters. Via network, the
device can be accessed with the device name instead of the ip address.
Confirm your selection with the green check.
SNTP Enter the address of an intranet or internet time server. Define an interval in mil-
liseconds for time synchronization.
Confirm your selection with the green check.
The input fields are only active when you set up a static ip.
P Line Touch Panel Installation and Commissioning
39
2.4.1.2.5 Password
The menu item Password allows you to protect certain menu items in the cockpit
with a password.
Current password
1. Enter a password for the protected menu items.
2. Confirm your selection with the green check.
Password protected
1. Select the menu items which shall get a password protection.
2. Confirm your selection with the green check.
2.4.1.2.6 Display
This category offers the following functions:
– Brightness and orientation of the display
– Calibration of the touch
Brightness 1. Adjust the brightness using the slider or the arrow symbols.
2. Confirm your selection with the green check.
Orientation 1. Turn the orientation using the buttons Turn left and Turn right to the desired
position.
2. Confirm your selection with the green check.
Depending on device type, the new orientation is accepted immediately or after a
reboot of the operating device.
3. Press the OK button.
Calibrate Touch 1. Press the Recalibrate button.
Depending on device type the calibration is automatically started immediately or
after a reboot of the operating device.
2. Press the displayed marks to calibrate the touch.
2.4.1.2.7 Write Filter
This category offers the following functions:
– Enhanced write filter (EWF)
– File based write filter (FBWF)
– Hibernate once, resume many (HORM)
EWF The enhanced write filter (EWF) protects your system from write access and in-
stead writes the data to the main memory.
Enable EWF
1. Press the Enable EWF button.
2. Confirm your selection with the green check.
3. Restart the operating device for the changes to take effect.
NOTICE
With enabled write protection, all data in the main memory of the operating device are lost after a restart.
Installation and Commissioning P Line Touch Panel
40
Disable EWF
1. Press the Disable EWF button.
2. Confirm your selection with the green check.
3. Restart the operating device for the changes to take effect.
FBWF The file based write filter (FBWF) protects your system from write access and in-
stead writes the data to the main memory. The selected folders are not protected.
Enable FBWF
1. Press the Enable FBWF button.
2. Confirm your selection with the green check.
3. Restart the operating device for the changes to take effect.
Disable FBWF
1. Press the Disable FBWF button.
2. Confirm your selection with the green check.
3. Restart the operating device for the changes to take effect.
Exclude Folders
1. Select the folders that should be not write protected.
2. Press the Exclude Folders button.
3. Confirm your selection with the green check.
4. Restart the operating device for the changes to take effect.
HORM The current state of the system can be saved and restored automatically at every
startup. The boot process is accelerated by this function.
Enable HORM
To use HORM, EWF must be active.
1. Press the Enable HORM button.
2. Press the Hibernate System button to save the current state.
Disable HORM
1. Press the Disable HORM button.
2. Confirm your selection with the green check.
3. Restart the operating device for the changes to take effect.
Hibernate System
1. Press the Hibernate System button.
The operating device is set to hibernation. Thereby the current state of the system
is saved and restored automatically at every startup.
NOTICE
With enabled write protection, all data in the main memory of the operating device are lost after a restart.
P Line Touch Panel Installation and Commissioning
41
2.5 Identification
The operating device can be identified using the nameplate on the rear of the device.
Figure 2-29 Nameplate (example)
1 Device Type
2 Software Version (Version on Delivery)
3 MAC Addresses
4 Voltage and Current
5 Serial Number
Installation and Commissioning P Line Touch Panel
42
P Line Touch Panel Control and Display Elements
43
3 Control and Display Elements
3.1 Touch Screen
The device is equipped with a resistive 4 wire touch screen. You operate the device using this touch screen.
3.2 Display
The operating device is equipped with different displays depending on variant.
NOTICE: Damage
Pointed or sharp objects, such as pens or fingernails, can lead to irreparable
damages of the touch screen. Exclusively therefore use the fingertips or the
aids indicated in the technical data for the operation.
NOTICE: Damage
To protect the touch screen you can use special protection foils. You receive
corresponding protection foils directly from Sütron electronic.
DANGER: Toxic
If the display is damaged, avoid touching, swallowing or breathing in the liquids
or gases which may leak out!
DANGER: Corrosive
If the display is damaged, avoid touching, swallowing or breathing in the liquids
or gases which may leak out!
Control and Display Elements P Line Touch Panel
44
P Line Touch Panel Interfaces of the Device
45
4 Interfaces of the Device
Figure 4-1 Rear view
1 Slot for SD / SDHC Memory Card
2 Ethernet X7, X6 (10/100/1000 MBit)
3 Female Connector X2 - X5 (USB Host - Type A)
4 Supply Voltage
5 Threaded Bolt For Protective Grounding
Interfaces of the Device P Line Touch Panel
46
4.1 Ethernet
10/100/1000 Base-T Ethernet interfaces are available at the operating device.
4.1.1 Pin Assignment
Connector in the operating device: RJ45 female connector.
4.1.2 Cable
Table 4-1 Pin assignment of the Ethernet interface
Pin Designation Function
1 D1+ Data Line 1, Positive Polarity
2 D1- Data Line 1, Negative Polarity
3 D2+ Data Line 2, Positive Polarity
4 D3+ Data Line 3, Positive Polarity
5 D3- Data Line 3, Negative Polarity
6 D2- Data Line 2, Negative Polarity
7 D4+ Data Line 4, Positive Polarity
8 D4- Data Line 4, Negative Polarity
ACHTUNG
Use a twisted pair cable of category 5 or 6 (CAT 5 or 6). Use twisted pair cable
of category 6 for optimal transfer rate at 1000 Base-T. The maximum cable
length is 100 m (328.084 feet).
See the IEEE 802.3 standard for further information.
P Line Touch Panel Interfaces of the Device
47
4.1.3 Diagnosis
Ethernet diagnostics LEDs are located at the ethernet interface of the operating
device.
Figure 4-2 Arrangement of the Ethernet diagnostics LEDs
4.2 USB
USB interfaces are available at the operating device to connect periphery equipment (for example: Mass memory, printer, scanner, mouse, keyboard etc.).
4.2.1 Cable
Table 4-2 Function of Ethernet diagnostics LEDs
No. Color State Function
1 Yellow Flashing Sending / Receiving activity
100/1000 MBit
Green Flashing Sending / Receiving activity
10 MBit
2 Yellow On 1000 MBit
Green On 100 MBit
-Off 10 MBit
NOTICE
Using hardware not suitable for industrial use (e.g. keyboard, mouse, memory
card) may decrease safety of operation. This includes hardware intended for
home and office use.
For the specification of a suitable cable, please refer to the „Universal Serial Bus
Specification Rev. 2.0“.
NOTICE
Use industrial-suited USB cables with a length of maximally 2.5 m (8.202 feet).
Interfaces of the Device P Line Touch Panel
48
4.3 Serial Interfaces
Figure 4-3 Rear view RS-422 / RS-485, RS-232
1 Slot for SD / SDHC Memory Card
2 Ethernet X7, X6 (10/100/1000 MBit)
3 Female Connector X2 - X5 (USB Host - Type A)
4 Supply Voltage
5 Diagnostics LEDs (RS-422/RS-485)
6 Termination Switch (RS-422/RS-485)
7 Male Connector X14 (RS-422/RS-485)
8 Diagnostics LEDs (RS-232)
9 Male Connector X15 (RS-232)
10 Threaded Bolt For Protective Grounding
P Line Touch Panel Interfaces of the Device
49
4.3.1 RS-422 / RS-485 (X14)
The interface standard RS-422 / RS-485 is suitable for point-to-point and multipoint connections.
The wires belonging together are marked with „A“ and „B“. Some descriptions refer to the pins with „-“ and „+“ , where A = - and B = +.
The interface is assigned to the port COM4. At an image version before 181 and
operating system Windows CE 6.0 the port COM1 is assigned.
4.3.1.1 Pin Assignment
Figure 4-4 9 pin D-SUB male connector strip
Connector in the operating device: 9 pin D-SUB male connector strip.
Signal Logic 1 U
A
- UB <= -0.3 V i.e. (UA < UB)
Signal Logic 0 U
A
- UB >= +0.3 V i.e. (UA > UB)
Table 4-3 Pin assignment RS-422/RS-485
Pin Designation Function
1 SGND Signal Ground
2 T(B) Transmitted Data + P
3 T(A) Transmitted Data - N
4 R(A) Received Data - N
5 R(B) Received Data + P
6 nc Not Connected
7 nc Not Connected
8 nc Not Connected
9 nc Not Connected
NOTICE
The D-SUB connector strips must be shielded sufficiently. See chapter “Shielding D-SUB Connectors“ on page 4-57.
Interfaces of the Device P Line Touch Panel
50
4.3.1.2 Termination
Always turn on the termination in a 4-wire point-to-point connection (RS-422 / RS-
485). A sender termination for the quiescent level of the receiver must exist on the
remote station.
Turn on the termination only at the two ends of the lines in a 2 or 4-wire multi-point
connection (RS-422 / RS-485).
Figure 4-5 Termination possibilities RS-422 / RS-485 (intern)
Table 4-4 Resistance values termination RS-422 / RS-485
Designation Value
R1 120 Ohm
The switch positions for ON or OFF are printed onto the operating device. Only
the specified switch positions are allowed.
Table 4-5 Termination switch RS-422 / RS-485
Switch position Function
ON Receiver termination
(120 Ohm)
OFF No receiver termination
P Line Touch Panel Interfaces of the Device
51
4.3.1.3 Transmitter Control
Switching between half-duplex and full-duplex is carried out by the DTR signal.
Full-duplex (DTR inactive / off):
The transmitter is always active and is not turned off on intermissions.
The receiver is always active.
Full-duplex (DTR active / on):
The transmitter is activated during the transmission. On intermissions, the transmitter is highly resistive.
The receiver is disabled during the transmission. The operating device does not
receive the own transmit data at the receiver.
4.3.1.4 Diagnosis
Diagnostics LEDs are located on the rear of the operating device.
The diagnostic LEDs at the operating device have the following functions:
Table 4-6 Functions of the RS-422 / RS-485 diagnostics LEDs
Designation Color State Function
Rx Green Flashes Data transfer active
Tx Yellow Flashes Data transfer active
Interfaces of the Device P Line Touch Panel
52
4.3.2 RS232 (X15)
The serial RS-232 interface is suitable to establish a point-to-point connection.
The interface is assigned to the port COM3. At an image version before 181 and
operating system Windows CE 6.0 the port COM0 is assigned.
4.3.2.1 Pin Assignment
Figure 4-6 9 pin D-SUB male connector strip
Connector in the operating device: 9 pin D-SUB male connector strip.
4.3.2.2 Diagnosis
Diagnostics LEDs are located on the rear of the operating device.
The diagnostic LEDs at the operating device have the following functions:
Table 4-7 Pin assignment RS-232
Pin Designation Function
1 nc Not Connected
2 RD Received Data
3 TD Transmitted Data
4 nc Not Connected
5 GND Ground
6 nc Not Connected
7 RTS Request to Send
8 CTS Clear to Send
9 nc Not Connected
NOTICE
The D-SUB connector strips must be shielded sufficiently. See chapter “Shielding D-SUB Connectors“ on page 4-57.
Table 4-8 Functions of the RS-232 diagnostics LEDs
Designation Color State Function
RD Green Flashes Data transfer active
TD Yellow Flashes Data transfer active
P Line Touch Panel Interfaces of the Device
53
4.4 Field Bus Interfaces
4.4.1 CAN (X12, X13)
Figure 4-7 Rear view CAN
1 Slot for SD / SDHC Memory Card
2 Ethernet X7, X6 (10/100/1000 MBit)
3 Female Connector X2 - X5 (USB Host - Type A)
4 Supply Voltage
5 Male Connector X12 (CAN1)
6 Termination Switch (CAN1)
7 Diagnostics LEDs (CAN1)
8 Diagnostics LEDs (Microcontroller)
9 Male Connector X13 (CAN2)
10 Termination Switch (CAN2)
11 Diagnostics LEDs (CAN2)
12 Diagnostics LEDs (RS-422/RS-485)
13 Termination Switch (RS-422/RS-485)
14 Male Connector X14 (RS-422/RS-485)
15 Diagnostics LEDs (RS-232)
16 Male Connector X15 (RS-232)
17 Threaded Bolt For Protective Grounding
Interfaces of the Device P Line Touch Panel
54
4.4.1.1 Pin Assignment
Figure 4-8 5 pin M12 male connector
Connector in the operating device: 5 pin M12 male connector.
4.4.1.2 Cable
The maximum cable length depends on the data transfer rate used.
Table 4-9 Pin assignment CAN 1
Pin Designation Function
1 PE Shielding
2 Reserved Reserved for DeviceNet
3 CAN1_GND CAN Ground
4 CAN1_H CAN_H Bus Line
5 CAN1_L CAN_L Bus Line
Table 4-10 Pin assignment CAN 2
Pin Designation Function
1 PE Shielding
2 Reserved Reserved for DeviceNet
3 CAN2_GND CAN Ground
4 CAN2_H CAN_H Bus Line
5 CAN2_L CAN_L Bus Line
NOTICE
The M12 connectors must be connected to the cable shield.
NOTICE
A shielded twisted-pair cable complying with ISO 11898-2 must be used.
A suitable cable with the designation „SAC-5P- 2,0-920/FS SCO“ is offerd by
Phoenix Contact GmbH with article number 1518216.
Table 4-11 Bit rate CAN
Bit rate Cable length
125 kBit/s 500 m
500 kBit/s 100 m
1 MBit/s 40 m
P Line Touch Panel Interfaces of the Device
55
4.4.1.3 Termination
Terminate the CAN bus at both ends by terminating resistors (120 Ohm).
4.4.1.4 Diagnosis
Diagnostics LEDs are located on the rear of the operating device. The LEDs show
the states of the bus system.
The diagnostics LEDs at the operating device have the following functions:
The switch positions for ON or OFF are printed onto the operating device. Only
the specified switch positions are allowed.
Table 4-12 Termination switch CAN
Switch position Function
ON Termination (120 Ohm)
OFF No termination
Table 4-13 Functions of the CAN diagnostics LEDs
Designation Color State Function
CAN1 Green On Node is operational
Green Flashes Node is not operational
CAN2 Green Ein Node is operational
Green Flashes Node is not operational
µC Green Off Microcontroller inactive
Green Flashes
slowly
Microcontroller is operational
Green Flashes
slowly
and fast
Microcontroller is operational
Requests of the host CPU are received and processed
Interfaces of the Device P Line Touch Panel
56
4.5 Memory Card
At the underside of the operating device you can plug in an SD card.
4.5.1 Inserting the memory card
If you insert the memory card, the back side (side with contacts) of the memory
card must be visible. Insert the memory card until it clicks.
Figure 4-9 Inserting the memory card
4.5.2 Ejecting the memory card
To remove, push the memory card into the operating device until it clicks. The
memory card bounces when released automatically out of the operating device.
Now you can remove the memory card.
NOTICE
Using hardware not suitable for industrial use (e.g. keyboard, mouse, memory
card) may decrease safety of operation. This includes hardware intended for
home and office use.
P Line Touch Panel Interfaces of the Device
57
4.6 Shielding D-SUB Connectors
You must shield D-SUB connectors as follows:
Figure 4-10 Shielding D-SUB connectors
1 D-SUB connector
2 Shield
3 Cable clip
4 Cable
The shield must be folded back into a flat position over the cable sheath.
When fastening the cable with the cable clip, as much of the shielding as possible
must be in contact with the housing and sufficient strain relieve must be ensured.
Interfaces of the Device P Line Touch Panel
58
P Line Touch Panel Maintenance and Servicing
59
5 Maintenance and Servicing
5.1 Maintenance Interval
The following maintenance intervals are recommended for this operating device:
5.2 Front Panel
Only use a damp cloth to remove any dirt from the front panel.
5.3 Fuse
A semiconductor fuse is used to protect the device. Once the fuse has been
tripped, the device must be disconnected from the supply voltage to allow the
semiconductor fuse to regenerate. At an ambient temperature of 20 °C (68 °F),
the regeneration takes approximately 20 seconds. The higher the ambient temperature, the longer the regeneration takes.
5.4 Battery
The minimum battery life is 5 years, even under unfavorable operating conditions.
We recommend you change the battery approximately every 4 years as part of
the regular maintenance work.
Table 5-1 Maintenance interval
Maintenance work Interval
Changing the Battery 4 Years
NOTICE: Damage
The semiconductor fuse cannot be replaced!
Maintenance and Servicing P Line Touch Panel
60
5.4.1 Changing the Battery
After a battery change, you must set the date and time newly!
1. Remove the connector of the supply voltage.
2. Remove the screws with the help of a screwdriver (see picture).
3. Remove the enclosure.
4. Disconnect the connector from the battery and remove the dead battery.
5. Plug in the cable of the new battery.
6. Use a provided glue strip to attach the new battery.
7. Place the enclosure cover back onto the device,
8. Carefully tighten the screws of the enclosure cover.
9. Put the connector for the supply voltage on again.
10. Set the current date and time.
Figure 5-1 Enclosure screws at the operating device
NOTICE: Damage
Batteries must only be changed by authorized and trained experts!
NOTICE: Damage
Electrostatic discharge can damage electronic components. Observe the ESD
protective measures!
CAUTION: Explosive
Do not throw lithium batteries into fire, do not heat to 100 °C or higher and do
not recharge.
CAUTION: Toxic
Do not open lithium batteries.
Take care at the assembly of the enclosure cover that all enclosure latches click
into the corresponding slits of the underlying enclosure.
P Line Touch Panel Maintenance and Servicing
61
5.4.2 Battery Disposal
The manufacturer is obliged to mark batteries with this symbol before first placing
into market. The symbol is extended by the chemical symbols if the following limiting values are exceeded:
Batteries can be given back free of charge after use at the place of purchase.
According to the §11 of the battery law, final consumers are obligedly to give old
batteries back to gathering points which attached to the common take back system or manufacturer-specific take back systems.
More than 0.0005 mass percent mercury Hg
More than 0.002 mass percent cadmium Cd
More than 0.004 mass percent lead Pb
NOTICE: Damage
To prevent short circuitry in the collection boxes, insulate the poles of each battery with insulation tape or put each single battery into a plastic bag.
Maintenance and Servicing P Line Touch Panel
62
P Line Touch Panel Technical Data
63
6 Technical Data
6.1 General
Touch Screen
Type Analog resistive, 4 wire technology
Activation force 15 g (Standard)
With R8 HS60 silicon rubber
Durability No damages or malfunctions after 3 million keystrokes as the following:
Keystroke element: R8, HS40 silicon rubber
Keystroke load: 150 g
Keystroke frequency: 3 Hz
Ethernet
Ethernet 10/100/1000 Mbit/s
USB
In accordance with the „Universal Serial Bus Specification Rev. 2.0“
Min.: 1.5 Mbit/s
Max.: 12 Mbit/s
Max. output current: 100 mA per output
Connection Method
Female and male connector strip PHOENIX CONTACT MINI COMBICON, 3 pin
RJ45 female connector
USB female connector A
Environmental Conditions
Temperature during
operation
0 °C to 50 °C (32 °F to 122 °F)
Temperature during
storage, transport
- 25 °C to + 70 °C (-13°F to + 158°F)
Relative air humidity for operation and storage 20 % to 85 %, no condensation
Application area Degree of pollution 2, overvoltage category III
No direct solar radiation
Technical Data P Line Touch Panel
64
Standards and Guidelines
Interference immunity EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-6-2
Emitted interference EN 61000-6-4
EN 50011 limit class value A
EN 50022 limit class value A
Equipment requirements EN 61131
Storage and transportation
EN 61131 part 2
Power supply EN 61131 part 2
Electromagnetic compatibility
2004/108/EG
Degree of protection EN 60529
Impact load, shocks EN 60068 part 2-27
Sinusoidal vibrations EN 60068 part 2-6
Corrosion protection IEC 60068
NOTICE: Radio Interference
This is a class A device. This device may cause radio interference in residential
areas. In this case, the user may be required to introduce appropriate countermeasures, and to bear the cost of same.
Approvals
CE
P Line Touch Panel Technical Data
65
6.2 TP057ZTV
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
14.48 (5.7)
Type TFT (color)
Resolution (pixels) 640 x 480
Colors 262144
Reading angle (vertical /
horizontal)
107° / 130°
Half-life backlighting 40,000 h
Brightness in cd/m
2
400
Display area (H x W) in
mm (Inch)
86.4 x 115.2 (3.402 x 4.535)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.5 A
Connected load 12 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
66
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
126 x 168 x 5
(4.961 x 6.614 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
118 x 160 (4.645 x 6.299)
Mounting depth in mm
(Inch)
About 54 (2.125)
Degree of protection Front: IP65
Rear: IP20
Total weight About 800 g
P Line Touch Panel Technical Data
67
6.3 TP057GTV
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
14.48 (5.7)
Type TFT (color)
Resolution (pixels) 640 x 480
Colors 262144
Reading angle (vertical /
horizontal)
107° / 130°
Half-life backlighting 40,000 h
Brightness in cd/m
2
400
Display area (H x W) in
mm (Inch)
86.4 x 115.2 (3.402 x 4.535)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.5 A
Connected load 12 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
68
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
126 x 168 x 5
(4.961 x 6.614 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
118 x 160 (4.645 x 6.299)
Mounting depth in mm
(Inch)
About 64 (2.519)
Degree of protection Front: IP65
Rear: IP20
Total weight About 800 g
P Line Touch Panel Technical Data
69
6.4 TP070ZTW
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
17.78 (7)
Type TFT (color)
Resolution (pixels) 800 x 480
Colors 262144
Reading angle (vertical /
horizontal)
130° / 140°
Half-life backlighting 40,000 h
Brightness in cd/m
2
350
Display area (H x W) in
mm (Inch)
91.4 x 152.4
(3.598 x 6.0)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.7 A
Connected load 16.8 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
70
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
147 x 203 x 5
(5.787 x 7.992 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
139 x 195
(5.7472 x 7.677)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 68 / 91 (2.677 / 3.582)
Degree of protection Front: IP65
Rear: IP20
Total weight About 1100 g
P Line Touch Panel Technical Data
71
6.5 TP070GTW
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
17.78 (7)
Type TFT (color)
Resolution (pixels) 800 x 480
Colors 262144
Reading angle (vertical /
horizontal)
130° / 140°
Half-life backlighting 40,000 h
Brightness in cd/m
2
350
Display area (H x W) in
mm (Inch)
91.4 x 152.4
(3.598 x 6.0)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.8 A
Connected load 19.2 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
72
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
147 x 203 x 5
(5.787 x 7.992 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
139 x 195
(5.7472 x 7.677)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 76 / 99 (2.992 / 3.897)
Degree of protection Front: IP65
Rear: IP20
Total weight About 1300 g
P Line Touch Panel Technical Data
73
6.6 TP090ZTW
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
22.86 (9)
Type TFT (color)
Resolution (pixels) 800 x 480
Colors 16.77 million
Reading angle (vertical /
horizontal)
170° / 170°
Half-life backlighting 70.000 h
Brightness in cd/m
2
400
Display area (H x W) in
mm (Inch)
118 x 197 (4.645 x 7.755)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.9 A
Connected load 21.6 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
74
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
172 x 260 x 5
(6.772 x 10.236 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
164 x 252
(6.456 x 9.921)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 68 / 91 (2.677 / 3.582)
Degree of protection Front: IP65
Rear: IP20
Total weight About 1400 g
P Line Touch Panel Technical Data
75
6.7 TP090GTW
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
22.86 (9)
Type TFT (color)
Resolution (pixels) 800 x 480
Colors 16.77 million
Reading angle (vertical /
horizontal)
170° / 170°
Half-life backlighting 70.000 h
Brightness in cd/m
2
400
Display area (H x W) in
mm (Inch)
118 x 197 (4.645 x 7.755)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.2 A
Connected load 28.8 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
76
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
172 x 260 x 5
(6.772 x 10.236 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
164 x 252
(6.456 x 9.921)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 76 / 99 (2.992 / 3.897)
Degree of protection Front: IP65
Rear: IP20
Total weight About 1600 g
P Line Touch Panel Technical Data
77
6.8 TP105ZTS
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
26.42 (10.4)
Type TFT (color)
Resolution (pixels) 800 x 600
Colors 262144
Reading angle (vertical /
horizontal)
110° / 140°
Half-life backlighting 50,000 h
Brightness in cd/m
2
340
Display area (H x W) in
mm (Inch)
158 x 211
(6.22 x 8.307)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.8 A
Connected load 19.2 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
78
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
220 x 295 x 5
(8.661 x 11.614 x 0.196)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
212 x 287
(8.346 x 11.299)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 80 / 103 (3.149 / 4.055)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2400 g
P Line Touch Panel Technical Data
79
6.9 TP105GTS
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
26.42 (10.4)
Type TFT (color)
Resolution (pixels) 800 x 600
Colors 262144
Reading angle (vertical /
horizontal)
110° / 140°
Half-life backlighting 50,000 h
Brightness in cd/m
2
340
Display area (H x W) in
mm (Inch)
158 x 211
(6.22 x 8.307)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.9 A
Connected load 21.6 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
80
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
220 x 295 x 5
(8.661 x 11.614 x 0.196)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
212 x 287
(8.346 x 11.299)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 87 / 110 (3.425 / 4.33)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2400 g
P Line Touch Panel Technical Data
81
6.10 TP121ZTS
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
30.73 (12.1)
Type TFT (color)
Resolution (pixels) 800 x 600
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
350
Display area (H x W) in
mm (Inch)
184.5 x 246 (7.263 x 9.685)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.8 A
Connected load 19.2 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
82
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
270 x 340 x 5 (10.63 x 13.386 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
243,5 x 315
(9.587 x 12.402)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 68 / 91 (2.677 / 3.582)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2400 g
P Line Touch Panel Technical Data
83
6.11 TP121GTS
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
30.73 (12.1)
Type TFT (color)
Resolution (pixels) 800 x 600
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
350
Display area (H x W) in
mm (Inch)
184.5 x 246 (7.263 x 9.685)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.2 A
Connected load 28.8 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
84
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
270 x 340 x 5 (10.63 x 13.386 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
243,5 x 315
(9.587 x 12.402)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 76 / 99 (2.992 / 3.897)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2400 g
P Line Touch Panel Technical Data
85
6.12 TP121ZTM
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
30.73 (12.1)
Type TFT (color)
Resolution (pixels) 1280 x 800
Colors 262144
Reading angle (vertical /
horizontal)
176° / 176°
Half-life backlighting 50,000 h
Brightness in cd/m
2
320
Display area (H x W) in
mm (Inch)
163.2 x 261.12 (6.425 x 10.28)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
0.9 A
Connected load 21.6 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
86
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
225 x 330 x 5
(8.858 x 12.992 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
217 x 322
(8.543 x 12.677)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 68 / 91 (2.677 / 3.582)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2100 g
P Line Touch Panel Technical Data
87
6.13 TP121GTM
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
30.73 (12.1)
Type TFT (color)
Resolution (pixels) 1280 x 800
Colors 262144
Reading angle (vertical /
horizontal)
176° / 176°
Half-life backlighting 50,000 h
Brightness in cd/m
2
320
Display area (H x W) in
mm (Inch)
163.2 x 261.12 (6.425 x 10.28)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.0 A
Connected load 24 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
88
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
225 x 330 x 5
(8.858 x 12.992 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
217 x 322
(8.543 x 12.677)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 76 / 99 (2.992 / 3.897)
Degree of protection Front: IP65
Rear: IP20
Total weight About 2300 g
P Line Touch Panel Technical Data
89
6.14 TP150ZTX
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
38.1 (15)
Type TFT (color)
Resolution (pixels) 1024 x 768
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
320
Display area (H x W) in
mm (Inch)
228 x 304
(8.976 x 11.969)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.0 A
Connected load 24 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
90
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
329 x 400 x 5 (12.953 x 15.748 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
302 x 373
(11.89 x 14.685)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 80 / 103 (3.149 / 4.055)
Degree of protection Front: IP65
Rear: IP20
Total weight About 3700 g
P Line Touch Panel Technical Data
91
6.15 TP150GTX
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
38.1 (15)
Type TFT (color)
Resolution (pixels) 1024 x 768
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
320
Display area (H x W) in
mm (Inch)
228 x 304
(8.976 x 11.969)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.3 A
Connected load 31.2 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
92
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
329 x 400 x 5 (12.953 x 15.748 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
302 x 373
(11.89 x 14.685)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 87 / 110 (3.425 / 4.33)
Degree of protection Front: IP65
Rear: IP20
Total weight About 3900 g
P Line Touch Panel Technical Data
93
6.16 TP154ZTM
Central Processing Unit
Central processing unit Intel® Atom™
Clock frequency 1.6 GHz
Display
Size (diagonal) in cm
(inch)
39.1 (15.4)
Type TFT (color)
Resolution (pixels) 1280 x 800
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
360
Display area (H x W) in
mm (Inch)
207 x 331 (8.149 x 13.031)
Memory
RAM 1 GByte DDR2
Flash 2 GByte / 8 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.0 A
Connected load 24 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
94
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
297 x 420 x 5 (11.692 x 16.535 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
273 x 396 (10.748 x 15.59)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 80 / 103 (3.149 / 4.055)
Degree of protection Front: IP65
Rear: IP20
Total weight About 3700 g
P Line Touch Panel Technical Data
95
6.17 TP154GTM
Central Processing Unit
Central processing unit AMD embedded G-Series
Clock frequency 1 GHz single / dual-core
Display
Size (diagonal) in cm
(inch)
39.1 (15.4)
Type TFT (color)
Resolution (pixels) 1280 x 800
Colors 262144
Reading angle (vertical /
horizontal)
140° / 160°
Half-life backlighting 50,000 h
Brightness in cd/m
2
360
Display area (H x W) in
mm (Inch)
207 x 331 (8.149 x 13.031)
Memory
RAM 2 GByte DDR2
Flash 8 GByte / 16 GByte / 32 GByte / 64 GByte
SD/SDHC interface 2 GByte / 32 GByte maximum
Electrical Data
Supply voltage 24 V DC (SELV / PELV in accordance with DIN EN 61131)
Residual ripple 10 % maximum
Power consumption (typical at 24 V)
1.4 A
Connected load 33.6 W
Fuse Semiconductor fuse, self-resetting
Protection against
polarity reversal
Integrated
Technical Data P Line Touch Panel
96
Front Panel and Enclosure
Enclosure Steel sheet, galvanized
Front panel material Aluminium, brushed, anodized natural finish
Front panel (H x W x D) in
mm (Inch)
297 x 420 x 5 (11.692 x 16.535 x 0.197)
Seal Circumferential rubber seal on the rear
Mounting cutout (H x W)
in mm (Inch)
273 x 396 (10.748 x 15.59)
Mounting depth in mm
(Inch) - (standard / field
bus)
About 87 / 110 (3.425 / 4.33)
Degree of protection Front: IP65
Rear: IP20
Total weight About 3900 g
P Line Touch Panel Ordering Data
97
7Ordering Data
Tabelle 7-1 Accessories
Description Part No.
SD card 512 MB 81152.513
USB 2.0 stick 1 GB 81152.100
USB 2.0 stick 2 GB 81152.200
USB 2.0 stick 8 GB 81152.800
Battery, assembled with cable and connector (Type: CR2450) 66779.100
Protective foil for touch screen 5.7" (Set with 10 protective foils, scraper and instructions) 81251.056
Protective foil for touch screen 7" (Set with 10 protective foils, scraper and instructions) 81251.070
Protective foil for touch screen 9" (Set with 10 protective foils, scraper and instructions) 81251.090
Protective foil for touch screen 10.4" (Set with 10 protective foils, scraper and instructions) 81251.104
Protective foil for touch screen 12.1" (Set with 10 protective foils, scraper and instructions) 81251.121
Protective foil for touch screen 15" (Set with 10 protective foils, scraper and instructions) 81251.150
Ordering Data P Line Touch Panel
98
99
A Index
A
Accessories.........................................................97
Administration .....................................................38
B
Battery.................................................................59
Battery disposal ..................................................61
C
Cable
CAN ............................................................54
Ethernet ......................................................46
USB ............................................................47
Changing the battery...........................................60
Cockpit
Structure .....................................................37
Connecting..........................................................34
D
Date ....................................................................38
Diagnosis
CAN ............................................................55
RS-232........................................................52
RS-422........................................................51
RS-485........................................................51
Dimensions
Cutout .........................................................18
Front panel..................................................10
Display ........................................................ 39
, 43
E
Ethernet ..............................................................46
F
Functions ............................................................37
Fuse ....................................................................59
I
Identification........................................................41
Intended use .........................................................8
Interface
CAN ............................................................53
RS-232........................................................52
RS-422........................................................49
RS-485........................................................49
USB ............................................................47
M
Maintenance .......................................................59
Maintenance interval...........................................59
Memory card .......................................................56
Mounting ...............................................................9
N
Nameplate...........................................................41
Network...............................................................38
O
Ordering data ..................................................... 97
P
Password ........................................................... 39
Pin assignment
CAN ........................................................... 54
Ethernet ..................................................... 46
RS-232....................................................... 52
RS-422....................................................... 49
RS-485....................................................... 49
R
Rear view
CAN ........................................................... 53
RS-422 / RS-485, RS-232 ......................... 48
S
Safety notes ......................................................... 7
Servicing ............................................................ 59
Settings .............................................................. 37
Standards........................................................... 64
Structure
Cockpit ....................................................... 37
Supply Voltage ................................................... 34
Switching on....................................................... 36
T
Target group......................................................... 8
Technical data.................................................... 63
Termination
CAN ........................................................... 55
RS-485....................................................... 50
Time ................................................................... 38
Touch screen ..................................................... 43
U
Unpacking ............................................................ 9
V
Version ............................................................... 41
100
Loading...