Sureheat FSR38 User Manual

‘Four

Professional Stainless Steel Grill:
30”, 38” & 48” Models

Seasons

USE AND CARE MANUAL

FOR.OUTDOOR Use only

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or other injury

Extreme care should he used because of the high temperatures produced by this appliance.

CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING
OPERATED

- ‘This appliance must he kept clear from combustible materials, gasoline or

other flammable vapors and liquids. Do not allow flammable materials to come in
contact with grate, burner or hot surfaces.

- Do not repair or replace any part of this appliance unless it is specifically

recommended in this manual. A qualified service technician should conduct all other
service.

- Follow the installation and servicing instructions provided with this product

Have your grill installed
valve

so that you know how to shut the gas off to your grill. if you smell gas, make sure all

gas connections are tight before operation. If you continue to smell gas call a
qualified technician.

- When lighting a burner, always pay close attention to what you are doing. Be

certain you are pushing the ignitor that lights the burner you intend

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance

2. Extinguish any open flames.

3. Open lid,

4, II odor continues, immediately call your gas supplier.

This appliance is not intended to be

installed in or on recreational vehicles or boats.

TES1tE) IN ACCORDANCE WITH ANSI.

Z2I.58~~t995fCGA I.6-M95 STANDARD FOR

OUTDOOR COOKING GAS APPLIANCES.

THIS GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the proper method of’ installation. In the absence of local codes, this
unit should be installed in accordance with the National Fuel Gas Code No. Z223.l-l 998 and the National
Electrical Code ANSI/NFPA No.70—

by a qualified service technician. Locate the main gas supply

on using.

F
O
R

Y
O
U
R

S
A
F
E
T
Y

1)0 N0’l’ store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

app1iancc.

\%ARNING

Grill

DO NO’I’ try lighting this appliance

without reading the “I.IGHTING
INSTRUCTIONS” section of this manual

IMPORTANT: Remove all protective plastic film from
stainless steel parts prior to assembly/use. This film is

installed at the factory to prevent damage that could occur
during shipment and handling.

LEFT SHELF ASSEMBLY

1. Open the grill hood and place a piece of
Styrofoam from the packaging under the grill hood to
prop the grill hood

open slightly. (See Fig. 1)

2. Attach the left shelf by
hooks into the slots on the side of the grill. (See Fig.

1)

3. After Inserting the four shelf hooks,
shelf against the grill and press downward until the
shelf locks in place. Make sure the lop strip is
hanging all the way inside of the grill before pressing
downward. (See Fig. 1)

4. Install one self tapping screw into the bottom
front hole of the shelf to lock shelf in place. (See Fig.

2)

Assembly

inserting the four shelf

press the

.

SJDE$JJflfr2&EB1ARIS.AS~E!4WW1

1. Remove side burner assembly from
packaging. (See Fig. 3)

2. Place a piece of Styrofoam from the
packaging in the grill to leave the grill hood propped
open slightly.

(See Fig. 4)

3. Attach the right side burner by inserting the four
shelf hooks into the slots on the side of the grill. (See
Fig. 4)

4. After inserting the four shelf hooks, press the
side burner shelf against the grill and press downward
until the shelf locks in place. Make sure the top strip is
hanging all the way inside of the grill before pressing
downward.

(See Fig. 4)

Grill Assembly

5. Slide the valve assembly through the center hole
in the front of the shelf. (See Fig. 5)

6. Insert one valve screw through the bezel and in to
the side burner valve arid tighten. Next, install the
second

screw through the bezel and tighten (See Fig. 6)

valve

7. Press the side burner assembly upward into the
side burner tray (See
tapping

screws from the top of the

8. Install metal knob~ making sure to line up the flat
side of the valve stern with the flat side of the knob
stem.

(See Fig. 9)

9. Install side burner head and cap. (See Fig. 10-11)

fig. 7) and Install two (2) self

tray. (See Fig. 8)

10. install grate over side burner. (See Fig. 12)

8