SUPER MICRO Computer 6113L-8, 6113L-i User Manual

SUPER

SUPERSERVER 61 13L-8

SUPERSERVER 61 13L-i

®

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER,
you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2004 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6113L-8/
6113L-i. Installation and maintainance should be performed by experienced
technicians only.

The SuperServer 6113L-8/6113L-i is a high-end, dual Itanium2 processor
rackmount server based on the SC813HS-500/SC813Hi-500 1U rackmount server
chassis and the i2DML-8G2/i2DML-iG2 serverboard.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with the
server system and describes the main features of the SUPER i2DML-8G2/i2DML­iG2 serverboard and the SC813HS-500/SC813Hi-500 chassis.

Preface

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 6113L-8/
6113L-i into a rack and check out the server configuration prior to powering up
the system. If your server was ordered without processor and memory compo­nents, this chapter will refer you to the appropriate sections of the manual for
their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6113L-8/6113L-i.

iii

SUPERSERVER 6113L-8/6113L-i User's Manual

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the i2DML-8G2/i2DML-iG2
serverboard, including the locations and functions of connectors, headers and
jumpers. Refer to this chapter when adding or removing processors or main
memory and when reconfiguring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the 1U SC813HS-500/SC813Hi-500
rackmount server chassis. You should follow the procedures given in this chapter
when installing, removing or reconfiguring SCSI/IDE or peripheral drives and when
replacing the system power supply unit and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed infor­mation on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Specifications

iv

Notes

Preface

v

SUPERSERVER 6113L-8/6113L-i User's Manual

Table of Contents

Preface

About This Manual ....................................................................................................... i ii

Manual Organization .................................................................................................... i ii

Chapter 1: Introduction

1-1 Overview ............................................................................................................ 1- 1

1-2 Serverboard Features ...................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1- 5

1-4 Contacting Supermicro ................................................................................... 1- 7

Chapter 2: Server Installation

2-1 Overview ............................................................................................................ 2- 1

2-2 Unpacking the SuperServer 6113L-8/6113L-i................................................ 2 -1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location...................................................................... 2- 2

Rack Precautions...................................................................................... 2-2

Server Precautions.................................................................................... 2-2

2-4 Installing the Server into a Rack ................................................................... 2-3

Identifying the Sections of the Rack Rails ............................................ 2-3

Installing the Outer Rails ...........................................................................2-3

Installing the Server into the Rack ...........................................................2-4

Installing the Server into a Telco Rack ....................................................2-6

2-5 Checking the Serverboard Setup ................................................................... 2-7

2-6 Checking the Drive Bay Setup....................................................................... 2 -9

Chapter 3: System Interface

3-1 Overview ............................................................................................................ 3- 1

3-2 Control Panel Buttons..................................................................................... 3 - 1

Reset.......................................................................................................... 3-1

Power ......................................................................................................... 3-1

3- 3 Control Panel LEDs......................................................................................... 3-2

Overheat ..................................................................................................... 3-2

NIC2 ............................................................................................................ 3-2

NIC1 ............................................................................................................ 3-2

HDD ............................................................................................................ 3- 2

Power ......................................................................................................... 3-3

3-4 SCSI Drive Carrier LEDs................................................................................. 3-3

vi

Table of Contents

Chapter 4: System Safety

4-1 Electrical Safety Precautions...........................................................................4-1

4-2 General Safety Precautions .............................................................................4-2

4- 3 ESD Precautions...............................................................................................4-3

4-4 Operating Precautions ......................................................................................4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the i2DML-8G2/i2DML-iG2 Serverboard...........................................5-1

5- 2 Itanium2 Processor and Heatsink Installation................................................5-2

5-3 Connecting Cables ............................................................................................5-9

Connecting Data Cables ............................................................................5-9

Connecting Power Cables ..........................................................................5-9

Connecting the Control Panel .................................................................5-10

5-4 I/O Ports...........................................................................................................5-11

5-5 Installing Memory ............................................................................................5-11

5-6 Adding PCI Cards............................................................................................5-13

5-7 Serverboard Details ....................................................................................... 5-14

i2DML-8G2 Layout .................................................................................. 5-14

i2DML-8G2/i2DML-iG2 Quick Reference .............................................. 5-15

5-8 Connector Definitions.................................................................................... 5-16

EPS 12V Power Connector.................................................................... 5-16

Processor Power Connectors ................................................................ 5-16

Power Fail LED ....................................................................................... 5-16

NMI Button............................................................................................... 5-16

Power LED............................................................................................... 5-16

HDD LED ................................................................................................. 5-17

NIC1 LED ................................................................................................. 5-17

NIC2 LED ................................................................................................. 5-17

Overheat LED .......................................................................................... 5-17

Reset Button ........................................................................................... 5-18

Power Button........................................................................................... 5-18

Universal Serial Bus ............................................................................... 5-18

Front Panel USB Headers ..................................................................... 5-19

Serial Ports ............................................................................................. 5-19

GLAN 1/2 (Ethernet Ports) .................................................................... 5-19

Chassis Intrusion .................................................................................... 5-19

Fan Headers ............................................................................................ 5-20

Power Fault ............................................................................................. 5-20

Wake-on-Ring .......................................................................................... 5-20

vii

SUPERSERVER 6113L-8/6113L-i User's Manual

SMB ......................................................................................................... 5-21

SMB Power Connector ........................................................................... 5-21

5-9 Jumper Settings............................................................................................. 5-22

Explanation of Jumpers.......................................................................... 5-22

CMOS Clear ............................................................................................ 5-22

VGA Enable/Disable ............................................................................... 5-22

GLAN Enable/Disable............................................................................. 5-23

Watch Dog Enable/Disable.................................................................... 5-23

Power Fail Alarm Enable/Disable ......................................................... 5-23

SCSI Enable/Disable .............................................................................. 5-24

5-10 Onboard Indicators ........................................................................................ 5-24

GLAN LEDs ............................................................................................. 5-24

Debug LEDs ............................................................................................ 5-24

SCSI Activity LED ................................................................................... 5-25

5-11 SCSI and IDE Disk Drive Connections ....................................................... 5-25

IDE Connectors ....................................................................................... 5-25

Ultra320 SCSI Connectors ..................................................................... 5-26

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel ................................................................................................... 6-2

6-3 System Fans .................................................................................................... 6-3

System Fan Failure .................................................................................. 6 -3

Replacing System Cooling Fans............................................................. 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Removing the Front Bezel ....................................................................... 6 -4

Accessing the Drive Bays ....................................................................... 6 -5

SCSI/IDE Drive Installation ...................................................................... 6-6

CD-ROM Drive Installation ....................................................................... 6 -8

6-5 Power Supply................................................................................................... 6- 9

Power Supply Failure ............................................................................... 6-9

Removing/Replacing the Power Supply .................................................. 6- 9

Chapter 7: BIOS

7-1 Introduction.........................................................................................................7-1

7-2 Main Setup Screen ...........................................................................................7-2

7-3 Advanced Setup Screen ...................................................................................7-3

7-4 PCI/PnP Configuration ....................................................................................7-11

7-5 Security settings ............................................................................................. 7-12

7-6 Exit Options .....................................................................................................7-13

viii

Table of Contents

Appendices:

Appendix A: BIOS Error Beep Codes...................................................................... A-1

Appendix B: BIOS POST Codes .............................................................................. B-1

Appendix C: Software Installation ............................................................................ C-1

Appendix D: System Specifications ........................................................................ D-1

ix

SUPERSERVER 6113L-8/6113L-i User's Manual

Notes

x

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The Supermicro SuperServer 6113L-8/6113L-i is a high-end dual processor, 1U
rackmount server that features some of the most advanced technology currently
available. The SuperServer 6113L-8/6113L-i is comprised of two main sub­systems: the SC813HS-500/SC813Hi-500 1U rackmount chassis and the i2DML­8G2/i2DML-iG2 dual Itanium2 processor serverboard. Please refer to our web
site for information on operating systems that have been certified for use with the
SuperServer 6113L-8/6113L-i (www.supermicro.com).

In addition to the mainboard and chassis, various hardware components may
have been included with your SuperServer 6113L-8/6113L-i, as listed below:

! Two (2) 1U Itanium2 CPU heatsinks (SNK-0046)

! One (1) heatsink retention socket with hex key (SKT-0147-RM-IT2)

! Two (2) power pods: Itanium2 voltage regulator modules (VRM-0008)

! One (1) slim CD-ROM drive (CDM-TEAC-24(B))

! One (1) riser card (CSE-RR1U-X)

! Four (4) Ultra320 SCSI drive carriers (CSE-PT-39(B), 6113L-8 only)

! Four (4) IDE drive carriers (CSE-PT-42(B), 6113L-i only)

! One (1) front access USB and COM port tray (CSE-PT40(B))

! Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails to a rack/telco rack

! One (1) CD-ROM containing drivers and utilities

! SuperServer 6113L-8/6113L-i User's Manual

1-1

SUPERSERVER 6113L-8/6113L-i User's Manual

Note: "(B)" indicates black.

1-2 Serverboard Features

At the heart of the SuperServer 6113L-8/6113L-i lies the i2DML-8G2/i2DML-iG2,
a dual Intel Itanium2 processor serverboard designed to provide maximum perfor­mance. Below are the main features of the i2DML-8G2/i2DML-iG2.

Chipset

The i2DML-8G2/i2DML-iG2 is based on Intel's E8870 chipset, which is a high­performance chipset designed for high-end server platforms (see Figure 1-1).

The Intel 8870 chipset consists of the four primary components: the Scalable Node
Controller (SNC), the Server I/O Hub (SIOH), the DDR Memory Hub (DMH), and the
Scalability Port Switch (SPS). Complementary components include the I/O Hub
Controller (Intel ICH4), the Firmware Hub (FWH), and the PCI Bus Bridge (P64H2).

The SNC is the main component in the processor/memory subsystem. It con­nects to four DDR memory hubs through four separate links to provide a peak
memory bandwidth of 6.4 GB/s. Each DDR Memory Hub connects to two branch
channels and supports up to four DDR SDRAM DIMMs per channel. The
Scalability Port (SP) provides simultaneous, bi-directional signaling with an ag­gregate bandwidth of 6.4 GB/sec per port. Two SP ports per SNC provide a
maximum bandwidth capability of 12.8 GB/s. The SNC delivers balanced, high­bandwidth throughput across the processors, memory and I/O.

The SIOH is the central component of the I/O subsystem and provides the
connection between four Hub Interface 2.0 ports and two Scalability Ports. The
the SIOH with four Hub Interfaces has a aggregate peak bandwidth of 4 GB/sec.
The SIOH also offers a Hub Interface 1.5 connection to legacy I/O and firmware
via the I/O Controller Hub (ICH4).

The DMH is a bridge for data transfers between the SNC and the two DDR
memory channels. Each DMH has a maximum throughput of 1.6 GB/s and sup­ports up to eight single or double density registered DIMMs.

The SPS is not used in the i2DML-8G2/i2DML-iG2.

1-2

Chapter 1: Introduction

Processors

The i2DML-8G2/i2DML-iG2 supports single or dual Intel Itanium2 processors of
up to 1.50 GHz with a 6 MB L3 cache at a 400 MHz FSB. Please refer to the
support section of our web site for a complete listing of supported processors
(http://www.supermicro.com/support/).

Memory

The i2DML-8G2/i2DML-iG2 has eight 184-pin, DIMM slots that can support up to
16 GB of low-profile, registered ECC DDR200 (PC1600) SDRAM (DDR266 is
supported but at 200 MHz only). Module sizes of 128 MB, 256 MB, 512 MB, 1
GB and 2 GB may be used to populate the DIMM slots. (This serverboard has
has been designed to support 2GB DIMM modules for each memory slot, but it has
only been validated with 1GB memory modules.)

PCI Expansion Slots

The i2DML-8G2/i2DML-iG2 has one 64-bit, 133/100 MHz PCI-X slot available for
use in a 1U server configuration. A riser card is included with the server. This
riser card fits into a PCI-X slot on the serverboard and was designed specially for
the SC813HS-500/SC813Hi-500 chassis to support the use of one standard (full­length) PCI-X card.

ATI Graphics Controller

The i2DML-8G2/i2DML-iG2 features an integrated ATI video controller based on
the Rage XL graphics chip. Rage XL fully supports sideband addressing and AGP
texturing. This onboard graphics package can provide a bandwidth of up to 512
MB/sec over a 32-bit graphics memory bus.

Onboard Controllers/Ports

The i2DML-8G2 (only) includes an onboard LSI Ultra320 SCSI controller for dual­channel operation. Backpanel I/O ports on the 6113L-8/6113L-i include two COM
ports, two USB ports and a VGA (monitor) port. An Intel 82546EB Ethernet
controller provides support for two Gb LAN ports, which are also located on the
backpanel.

1-3

SUPERSERVER 6113L-8/6113L-i User's Manual

Other Features

Other onboard features are included to promote system health. These include
various voltage monitors, two CPU temperature sensors, four fan speed sensors,
a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.

Figure 1-1. E8870 Chipset Block Diagram

Processor 1 Processor 2

VGA

USB0/1/2/

3/4/5/6

PCI 32

USB 2.0

LPC

Super

I/O

IDE1

3x1MB

FWH

UDMA100

ICH4

3x1MB

FWH

COM1/2

IDE2

LPC Bus

IPMI

LPC Bus

Hublink0

SNC

SIOH

SCSI Cntrl

Hublink0

LSI U320

16 GB (Max.) DDR200

MRH_D
MRH_D

MRH_D
MRH_D

P64H2

PCI-X 100

PCI Slot

DIMM1
DIMM5

DIMM2
DIMM6

DIMM3
DIMM7
DIMM4
DIMM8

PCI-X 133

82546EB

GLAN

Cntrl

Riser Card

Note: This is a general block diagram. Please see the previous Serverboard

Features pages for details on the features of each serverboard.

1-4

Chapter 1: Introduction

1-3 Server Chassis Features

The SC813HS-500/SC813Hi-500 is one of Supermicro's third-generation 1U chas­sis and features four SCSI/IDE hard drive bays, a slim CD-ROM drive and a
revolutionary cooling design that can keep today's most powerful processors
running well below their temperature thresholds. The following is a general
outline of the main features of the SC813HS/SC813Hi-500 chassis.

System Power

When configured as a SuperServer 6113L-8/6113L-i, the SC813HS-500/SC813Hi­500 chassis includes a 500W cold-swap power supply.

Control Panel

The SC813HS-500/SC813Hi-500 control panel provides important system moni­toring and control information. LEDs indicate power on, network activity, hard
disk drive activity and system overheat conditions. Also present are a main
power button and a system reset button.

I/O Backplane

The SC813HS-500/SC813Hi-500 is a 1U rackmount chassis. Its I/O backplane
provides one full-length PCI-X slot, a COM port (another COM port is an onboard
header located near the USB2/3 ports), one VGA port, two USB ports and two
Ethernet (LAN) ports. (See Figure 1-2.)

Figure 1-2. I/O Backplane

USB Ports

VGA Port

Ethernet PortsCOM1 Port

PCI-X Slot

External SCSI Port

(6113L-8 only)

1-5

SUPERSERVER 6113L-8/6113L-i User's Manual

Cooling System

The SC813HS-500/SC813Hi-500 chassis' revolutionary cooling design has been
optimized to provide sufficient cooling for dual Itanium2 configurations. The
SC813HS-500/SC813Hi-500 includes two heavy duty 10-cm blower fans located
in the middle of the chassis. These fans operate continuously at full rpm. If they
break down, the ambient air temperature inside the chassis will rise and activate
an overheat LED. In addition, a high-speed 4-cm fan is also included to increase
the flow of cooling air through the system.

1-6

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

1-7

SUPERSERVER 6113L-8/6113L-i User's Manual

Notes

1-8

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6113L-8/
6113L-i up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your SuperServer 6113L-8/6113L-i system has come to you
with the processors and memory preinstalled. If your system is not already fully
integrated with a serverboard, processors, system memory etc., please turn to
the chapter or section noted in each step for details on installing specific com­ponents.

2-2 Unpacking the SuperServer 6113L-8/6113L-i

You should inspect the box the SuperServer 6113L-8/6113L-i was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
file a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
6113L-8/6113L-i. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fields
are generated. You will also need it placed near a grounded power outlet. Be
sure to read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6113L-8/6113L-i was shipped in should include two sets
of rail assemblies, six (four front and two rear) rail mounting brackets and screws
you will need to install the system into the rack. Follow the steps in the order
given to complete the installation process in a minimum amount of time. Please
read this section in its entirety before you begin the installation procedure out­lined in the sections that follow.

2-1

SUPERSERVER 6113L-8/6113L-i User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open

the front door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack

to allow for sufficient airflow and ease in servicing.

!

Warnings and Precautions!

!

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component

from the rack.

- You should extend only one component at a time - extending two or

more simultaneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you

install the rails.

- Install the heaviest server components on the bottom of the rack

first, and then work up.

- Use a regulating uninterruptible power supply (UPS) to protect the
server from power surges, voltage spikes and to keep your
system operating in case of a power failure.

- Allow the power supply units to cool before touching them.

- Always keep the rack's front door and all panels and components on

the servers closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

2-4 Installing the Server into a Rack

This section provides information on installing the SuperServer 6113L-8/6113L-i
into a rack unit with the rack rails provided. If the 6113L-8/6113L-i has already
been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There
are a variety of rack units on the market, which may mean the assembly proce­dure will differ slightly. You should also refer to the installation instructions that
came with the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies with the SuperServer 6113L­8/6113L-i. Each of these assemblies consists of two sections: an inner fixed
chassis rail that secures to the 6113L-8/6113L-i and an outer fixed rack rail
that secures directly to the rack itself. A pair of short brackets to be used
on the front side of the outer rails are also included.

Installing the Outer Rails

Begin by measuring the distance from the front rail to the rear rail of the rack.
Attach a short bracket to the front side of the right outer rail and a long bracket
to the rear side of the right outer rail. Adjust both the short and long brackets
to the proper distance so that the rail can fit snugly into the rack. Secure the
short bracket to the front side of the outer rail with two M4 screws and the long
bracket to the rear side of the outer rail with three M4 screws. Repeat these
steps for the left outer rail.

Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The first is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in
place when fully extended from the rack. This prevents the server from coming
completely out of the rack when you pull it out for servicing.

2-3

SUPERSERVER 6113L-8/6113L-i User's Manual

Figure 2-1. Installing the Rack Rails

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-2.

When the server has been pushed completely into the rack, you should hear the
locking tabs "click". Finish by inserting and tightening the thumbscrews that
hold the front of the server to the rack.

2-4

Chapter 2: Server Installation

Figure 2-2. Installing the Server into a Rack

(front bezel is optional)

2-5

SUPERSERVER 6113L-8/6113L-i User's Manual

Installing the Server into a Telco Rack

If you are installing the SuperServer 6113L-86113L-8/6113L-i into a Telco type
rack, follow the directions given on the previous pages for rack installation. The
only difference in the installation procedure will be the positioning of the rack
brackets to the rack. They should be spaced apart just enough to accommodate
the width of the telco rack.

Figure 2-3. Installing the Server into a Telco Rack

(front bezel is optional)

2-6

Chapter 2: Server Installation

2-5 Checking the Serverboard Setup

After you install the 6113L-8/6113L-i in the rack, you will need to open
the unit to make sure the serverboard is properly installed and all the connections
have been made.

1. Accessing the inside of the 6113L-8/6113L-i (see Figure 2-4):

First, release the retention screws that secure the unit to the rack. Grasp the
two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover. There is a large rectangular recess in the middle front
of the top cover to help you push the cover away from you until it stops. You
can then lift the top cover from the chassis to gain full access to the inside
of the server.

2. Check the CPUs (processors):

You may have one or two processors already installed into the serverboard.
Each processor needs its own heatsink and power pod (VRM) installed. See
Chapter 5 for instructions on processor and heatsink installation.

3. Verify the proper CPU clock ratio setting:

If the CPU speed is not automatically detected you may need to set the
correct speed with the BIOS Setup utility. See the appropriate setting in BIOS
(Chapter 7) for setting the proper CPU speed. (Most processor speeds are
automatically detected so this step should be unnecessary.)

4. Check the system memory:

Your 6113L-8/6113L-i server system may have come with system memory
already installed. Make sure all DIMMs are fully seated in their slots. For
details on adding system memory, refer to Chapter 5.

5. Installing add-on cards:

If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

2-7

SUPERSERVER 6113L-8/6113L-i User's Manual

Figure 2-4. Accessing the Inside of the SuperServer 6113L-8/6113L-i

6. Check all cable connections and airflow:

Make sure all power and data cables are properly connected and not blocking
the chassis airflow. See Chapter 5 for details on cable connections. Also,
check the air seals for damage. The air seals are located under the blower
fan and beneath the frame cross section that separates the drive bay area from
the serverboard area of the chassis.

2-8

Chapter 2: Server Installation

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI/IDE
drives have been properly installed and all connections have been made.

1. Accessing the drive bays:

All drives are accessable from the front of the server. For servicing the CD­ROM and IDE drives, you will need to remove the top chassis cover (not
necessary for SCSI drives). See Chapter 6 for details.

2. CD-ROM drive:

A slim CD-ROM drive should be preinstalled in your server. Refer to Chapter
6 if you need to reinstall a CD-ROM drive to the system.

3. Check the SCSI/IDE disk drives:

Depending upon your system's configuration, your system may have one or
more SCSI (6113L-8) or IDE (6113L-i) drives already installed. If you need to
install SCSI/IDE drives, please refer to Chapter 6.

4. Check the airflow:

Airflow is provided by two heavy duty 10-cm blower fans and one high-speed
4-cm fan. The system component layout was carefully designed to direct
sufficient cooling airflow to the components that generate the most heat. Note
that all power and data cables have been routed in such a way that they do
not block the airflow generated by the fans.

5. Supplying power to the system:

The last thing you must do is to provide input power to the system. Plug the
power cord from the power supply unit into a high-quality power strip that offers
protection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS).

2-9

SUPERSERVER 6113L-8/6113L-i User's Manual

Notes

2-10

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the chassis control panel to keep you constantly
informed of the overall status of the system as well as the activity and health of
specific components. There are also two buttons on the chassis control panel
and an on/off switch on the power supply. This chapter explains the meanings
of all LED indicators and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis. These are
(in order from left to right) a reset button and a power on/off button.

RESET

! RESET: The reset switch reboots the system.

! POWER: This is the main power switch, which is used to apply or turn off

the main system power. Turning off system power with this button removes the
main power but keeps standby power supplied to the system.

3-1

SUPERSERVER 6113L-8/6113L-i User's Manual

3-3 Control Panel LEDs

The control panel located on the front of th SC813HS-500/SC813Hi-500 chassis
has four LEDs. These LEDs provide you with critical information related to
different parts of the system. This section explains what each LED indicates
when illuminated and any corrective action you may need to take.

! OVERHEAT: Indicates an overheat condition in the chassis. This may be
caused by cables obstructing the airflow in the system, or the ambient room
temperature being too warm. You should also check to make sure that the
chassis cover is installed and that all fans are present and operating normally.
Finally, check the air seals for damage. The air seals are located under the
blower fan and beneath the frame cross section that separates the drive bay area
from the serverboard area of the chassis.

NIC2

! NIC2: Indicates network activity on GLAN2 when flashing .

NIC1

! NIC1: Indicates network activity on GLAN1 when flashing.

! HDD: Indicates SCSI/IDE channel activity. On the SuperServer 6113L-8/

6113L-i this light indicates SCSI/IDE and/or CD-ROM drive activity when flashing.

3-2

Chapter 3: System Interface

! Power: Indicates power is being supplied to the system's power supply

units. This LED should normally be illuminated when the system is operating.

3-4 SCSI Drive Carrier LEDs (6113L-8 only)

Each SCSI drive carrier has two LEDs.

! Green: When illuminated, the green LED on the front of the SCSI drive

carrier indicates drive activity. A connection to the SCSI SCA backplane enables
this LED to blink on and off when that particular drive is being accessed.

! Red: A SAF-TE compliant backplane is needed to activate the red LED to

indicate a drive failure. If one of the SCSI drives fail, you should be notified by
your system management software. Please refer to Chapter 6 for instructions on
replacing failed SCSI drives.

3-3

SUPERSERVER 6113L-8/6113L-i User's Manual

Notes

3-4

Chapter 4: System Safety

Chapter 4

System Safety

4-1 Electrical Safety Precautions

!

Basic electrical safety precautions should be followed to protect yourself
from harm and the SuperServer 6113L-8/6113L-i from damage:

! Be aware of the locations of the power on/off switch on the chassis as well as

the room's emergency power-off switch, disconnection switch or electrical
outlet. If an electrical accident occurs, you can then quickly remove power
from the system.

! Do not work alone when working with high voltage components.

! Power should always be disconnected from the system when removing or

installing main system components, such as the serverboard, memory
modules and the CD-ROM drive (not necessary for the SCSI drives). When
disconnecting power, you should first power down the system with the
operating system and then unplug the power cords of all the power supply
units in the system.

! When working around exposed electrical circuits, another person who is familiar

with the power-off controls should be nearby to switch off the power if
necessary.

! Use only one hand when working with powered-on electrical equipment. This

is to avoid making a complete circuit, which will cause electrical shock. Use
extreme caution when using metal tools, which can easily damage any
electrical components or circuit boards they come into contact with.

! Do not use mats designed to decrease electrostatic discharge as protection

from electrical shock. Instead, use rubber mats that have been specifically
designed as electrical insulators.

4-1

SUPERSERVER 6113L-8/6113L-i User's Manual

! The power supply power cord must include a grounding plug and must be

plugged into grounded electrical outlets.

! Serverboard Battery: CAUTION - There is a danger of explosion if the onboard

battery is installed upside down, which will reverse its polarities. On the
i2DML-8G2/i2DML-iG2, the positive side should be facing up. This battery
must be replaced only with the same or an equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.

! CD-ROM Laser: CAUTION - this server may have come equipped with a CD-ROM

drive. To prevent direct exposure to the laser beam and hazardous radiation
exposure, do not open the enclosure or use the unit in any unconventional
way.

4-2 General Safety Precautions

!

Follow these rules to ensure general safety:

! Keep the area around the SuperServer 6113L-8/6113L-i clean and free of clutter.

! The SuperServer 6113L-8/6113L-i weighs approximately 42 lbs (19.1 kg) when

fully loaded. When lifting the system, two people at either end should lift
slowly with their feet spread out to distribute the weight. Always keep your
back straight and lift with your legs.

! Place the chassis top cover and any system components that have been

removed away from the system or on a table so that they won't accidentally
be stepped on.

! While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits
or be pulled into a cooling fan.

! Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into
contact with printed circuit boards or areas where power is present.

4-2

Chapter 4: System Safety

! After accessing the inside of the system, close the system back up and secure

it to the rack unit with the retention screws after ensuring that all connections
have been made.

4-3 ESD Precautions

!

Electrostatic discharge (ESD) is generated by two objects with different
electrical charges coming into contact with each other. An electrical discharge
is created to neutralize this difference, which can damage electronic com­ponents and printed circuit boards. The following measures are generally
sufficient to neutralize this difference before contact is made to protect your
equipment from ESD:

! Use a grounded wrist strap designed to prevent static discharge.

! Keep all components and printed circuit boards (PCBs) in their antistatic bags

until ready for use.

! Touch a grounded metal object before removing any board from its antistatic
bag.

! Do not let components or PCBs come into contact with your clothing, which
may retain a charge even if you are wearing a wrist strap.

! Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or contacts.

! When handling chips or modules, avoid touching their pins.

! Put the serverboard and peripherals back into their antistatic bags when not

in use.

! For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

4-3

SUPERSERVER 6113L-8/6113L-i User's Manual

4-4 Operating Precautions

!

Care must be taken to assure that the chassis cover is in place when the 6113L­8/6113L-i is operating to ensure proper cooling. Out of warranty damage to the
6113L-8/6113L-i system can occur if this practice is not strictly followed.

4-4

Chapter 5: Advanced Serverboard Setup

Chapter 5

Advanced Serverboard Setup

This chapter covers the steps required to install processors and heatsinks to the
i2DML-8G2/i2DML-iG2 serverboard, connect the data and power cables and in­stall add-on cards. All serverboard jumpers and connections are described and
a layout and quick reference chart are included in this chapter. Remember to
close the chassis completely when you have finished working on the serverboard
to protect and cool the system sufficiently.

5-1 Handling the i2DML-8G2/i2DML-iG2 Serverboard

Static electrical discharge can damage electronic components. To prevent dam­age to printed circuit boards, it is important to handle them very carefully (see
Chapter 4). Also note that the size and weight of the serverboard can cause it
to bend if handled improperly, which may result in damage. To prevent the
serverboard from bending, keep one hand under the center of the board to support
it when handling. The following measures are generally sufficient to protect your
equipment from static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic
bag.

• Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

5-1

SUPERSERVER 6113L-8/6113L-i User's Manual

5-2 Itanium2 Processor and Heatsink Installation

When handling the processor package, avoid placing direct pressure
on the label area of the fan. Also, do not place the serverboard on
a conductive surface, which can damage the BIOS battery and

!

prevent the system from booting up.

IMPORTANT: Always connect the power cord last and always remove it before
adding, removing or changing any hardware components. Make sure that you
install the processor into the CPU socket before you install the CPU heatsink.

To optimize the functionality and capability of the i2DML-8G2/i2DML-iG2, we
recommend it be installed in Supermicro chassis only.

Warning: The heatsink on the MRH-D chip has been pre-installed by the
manufacturer. Please do not touch it. Turning the heatsink the wrong way will
damage it and will void the manufacturer's warranty.

Locating the Components

Locate the following components, which are included in the shipping package.

! Two (2) power pods (VRM-0008)

! Two (2) Itanium2 heatsinks (SNK-0046)

! One (1) heatsink retention package, which includes:

One (1) heatsink retention mechanism (SKT-0147-RM-IT2)
Eight (8) 5-mm M3 screws
Three (3) 6-32, 4.5-mm screws
Six (6) 6-32 9-mm screws
One (1) M2.5 hex key (for CPU removal and locking)

5-2

Chapter 5: Advanced Serverboard Setup

Installing the Heatsink Retention Mechanism

1. Place the retention mechanism (SKT-0147-RM-IT2) on the serverboard as
shown in the picture below:

2. Secure the retention mechanism to the serverboard by screwing three 6-32,

4.5-mm screws into the mounting holes on the back of the serverboard.

Figure 5-1. Installing Heatsink Retention Mechanism

5-3

1.) Place the retention
mechanism on the
serverboard.

2.) Screw in three 6-32

4.5-mm screws from the
reverse side of the
serverboard.

SUPERSERVER 6113L-8/6113L-i User's Manual

Installing Itanium2 CPUs

1. Insert an Itanium2 CPU into the CPU1 socket. Make sure that CPU Pin 1 is
aligned with the cut angle of the CPU socket, as shown in the picture below.*

Itanium2 CPU

2. Use the M2.5 hex key to secure the Itanium2 CPU as shown in the picture
below.

Securing the CPU with

an M2.5 hex key

3. Make sure that the CPU is in its properly locked position. To lock it, use the
M2.5 hex key to turn the lock in a clockwise direction. To unlock it, turn the lock
in a counter-clockwise direction.

CPU-unlocked CPU-locked

CPU1 Socket

Pointer

4. Repeat steps 1 and 2 to install a second Itanium2 CPU as needed.*
* Please refer to the serverboard layout page in this chapter for the locations

of the CPU1 and CPU2 sockets.

Pointer

5-4

Chapter 5: Advanced Serverboard Setup

Installing the Power Pods

The CPU power pod is a VRM mechanism specially designed for Itanium2 pro­cessors.

1. Locate the slot on the CPU power pod and align it with the Itanium2 CPU
installed on the serverboard.

2. Carefully push the edge connector of the power pod toward the CPU until the
signal pins on both edges of the CPU are fully seated in the edge connector and
you hear a click.

!

Warning: If the signal
pins of the CPU are not
fully seated in the edge
connector of the power
pod, the CPU will not
function correctly!!

Itanium2 CPU

CPU power pod

Power pod slot

Edge connector

Signal pins

5-5

SUPERSERVER 6113L-8/6113L-i User's Manual

3. Locate four of the M3 screws in the heatsink retention package and use them
to secure the power pod onto the serverboard as shown in the picture below.

Securing the power pod with four M3 screws.

4. Repeat steps 1 and 2 to install a second power pod as needed.

Figure 5-2. Dual Itanium2 CPUs with Power Pods Installed

5-6

Chapter 5: Advanced Serverboard Setup

Installing Heatsinks (for CPUs without heatsinks)

Warning: Do not apply any thermal grease to the heatsink; the required amount

of thermal grease has already been applied.
To maximizing the cooling effect of the i2DML-8G2/i2DML-iG2, we strongly rec-

ommend that Supermicro's proprietary heatsinks (SNK-0046) be used with
Itanium2 CPUs.

1. Place a heatsink (SNK-0046) on top of the CPU so that the four mounting holes
are aligned with those on the retention mechanism as shown in Figure 1 below.

2. Screw in two diagonal screws (eg. the #1 and #2 screws) until just snug (do
not fully tighten), then do the same with the remaining diagonal screws as shown
in Figure 2 and Figure 3.

Figure 1

Figure 2

Mounting holes

Figure 3

5-7

SUPERSERVER 6113L-8/6113L-i User's Manual

3. Secure the heatsink onto the CPU by tightening all four screws.

4. Repeat the above steps to install a second heatsink on a second CPU if
needed.

Figure 5-3. CPUs (2) with Heatsinks Installed

Connecting AC Power

1. Connect the 24-pin power connector from the AC power supply to the
serverboard. See the serverboard layout diagram in this chapter for the locations
of the power connectors.

2. Connect the two (2) 4-pin 12V power connectors from the AC power supply
to the power pods.

3. Refer to the next section for details on all connections.

5-8

Chapter 5: Advanced Serverboard Setup

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to
the serverboard. These include the data (ribbon) cables for the peripherals and
control panel and the power cables.

Connecting Data Cables

The ribbon cables used to transfer data from the peripheral devices have been
carefully routed in preconfigured systems to prevent them from blocking the flow
of cooling air that moves through the system from front to back. If you need to
disconnect any of these cables, you should take care to keep them routed as
they were originally after reconnecting them (make sure the red wires connect to
the pin 1 locations). If you are configuring the system, keep the airflow in mind
when routing the cables. The following data cables (with their serverboard con­nector locations noted) should be connected. See the serverboard layout figure
in this chapter for connector locations.

! SCSI Device Cable (J3, 6113L-8 only)

! IDE Device Cable (J37, 6113L-i only)

! CD-ROM Cable (J35)

! Front Side COM Port Cable (J38)

! Front Side USB Cable (J21)

! Control Panel Cable (U66, see next page)

Connecting Power Cables

The i2DML-8G2/i2DML-iG2 has two 24-pin primary power supply connectors
designated J20 and J36 for connection to the ATX power supply. Connect the
appropriate connector from the power supply to the either of these two connec­tors (only one connection is required) to supply power to the serverboard. See
the Connector Definitions section in this chapter for J20 and J36 pin definitions.

In addition, each processor requires a power pod. Each power pod must have
power supplied to it via one of the 4-pin header connectors included with your
power supply.

5-9

SUPERSERVER 6113L-8/6113L-i User's Manual

Connecting the Control Panel

The U66 header contains pins for various buttons and indicators that are normally
located on the chassis control panel. These connectors are designed specifi­cally for use with Supermicro server chassis. All U66 wires have been bundled
into single ribbon cable to simplify their connection. The red wire should plug into
pin 1 as marked on the serverboard. The other end connects to the Control Panel
printed circuit board, located just behind the system status LEDs in the chassis.

See the figure below for the descriptions of the various control panel buttons and
LED indicators. Refer to the Connector Definitions section in this chapter for
descriptions and pin definitions.

Figure 5-4. Front Control Panel Header Pins (U66)

1920

Ground

NMI

Power LED

HDD LED

NIC1 LED

NIC2 LED

Overheat LED

Po we r F a il LED

Ground

Ground

X

2

X

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset

Reset B u tton

Power Button

Pwr

1

5-10

Chapter 5: Advanced Serverboard Setup

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specification. See
Figure 5-5 below for the locations of the various I/O ports.

Figure 5-5. I/O Port Locations

COM Port USB Ports GLAN1 GLAN2 VGA Port External SCSI

(6113L-8 only)

5-5 Installing Memory

Note: Check the Supermicro web site for recommended memory modules: http://

www.supermicro.com/support/

CAUTION

Exercise extreme care when installing or removing DIMM modules

to prevent any possible damage. Also note that the memory is

interleaved to improve performance (see step 1).

DIMM Installation (See Figure 5-6)

1. Insert four identical DIMMs (modules of the same size and type) into the
DIMM1, DIMM2, DIMM3 and DIMM4 sockets (J16, J13, J11 and J9,
repectively). (These four DIMM sockets are colored blue.) If eight DIMMs
are to be used, insert four more identical DIMMs into the DIMM5, DIMM6,
DIMM7 and DIMM8 sockets (J15, J14, J12, and J10, respectively). (These
four DIMM sockets are colored black.) The memory scheme is interleaved,
so you must install four modules at a time, beginning with the blue DIMM1,
DIMM2, DIMM3 and DIMM4 sockets.

2. Insert each DIMM module vertically into its socket. Pay attention to the notch
along the bottom of the module to prevent inserting the DIMM module incor­rectly.

3. Gently press down on the DIMM module until it snaps into place in the socket.
Repeat for all modules (see step 1 above).

5-11

SUPERSERVER 6113L-8/6113L-i User's Manual

Memory Support

The i2DML-8G2/i2DML-iG2 supports up to 16 GB of buffered, reistered ECC
DDR200 (DDR266 memory can be used but will operate at DDR200 speed). This
serverboard was designed to support 2 GB modules in each socket. You should
not mix DIMMs of different sizes and speeds.

See Figures 5-6a and 5-6b for installing and removing memory modules.

Figure 5-6a. Side View of DIMM Installation into Socket

To Install: Insert module vertically and press down until it snaps
into place. Pay attention to the bottom notch.
To Remove: Use your thumbs to gently push each release tab
outward to free the DIMM from the socket.

Figure 5-6b. Top View of DIMM Socket

5-12

Chapter 5: Advanced Serverboard Setup

5-6 Adding PCI Cards

1. PCI-X slot:

The i2DML-8G2/i2DML-iG2 has one 64-bit 133 MHz PCI-X slot. The server
should have come with a riser card installed, which supports a standard sized
PCI-X card (see Figure 5-7).

2. PCI card installation:

Before installing a PCI add-on card, see step 1, above. Begin by swinging
the release tab on the I/O backpanel shield out to the left for the PCI slot.
Insert the PCI card into the correct slot on the butterfly riser card (depending
on whether it is a standard or low-profile card), pushing down with your
thumbs evenly on both sides of the card. Finish by pushing the release tab
back to its original (locked) position. Follow this procedure when adding a
card to either slot.

Figure 5-7. Low Profile vs. Standard PCI Card Form Factor

Standard PCI
Expansion Card

Low Profile PCI
Expansion Card

5-13

SUPERSERVER 6113L-8/6113L-i User's Manual

5-7 Serverboard Details

J5

COM1

J1

USB0/1

LAN1

LAN2

J2

VGA

Fan8

U62

1
5

2

6

Fan7

3
7

4
8

J18

SCSI CHA

J6

J7

82546

JA1

LSI SCSI

Controller

Figure 5-8. SUPER i2DML-8G2 Layout

(not drawn to scale)

CN5

MRH-D

DS7

J3

DIMM1
DIMM5

DIMM2
DIMM6

DIMM3
DIMM7

DIMM4
DIMM8

MRH-D

PCI-X (256 Pin)

BIOS4

BIOS3

SCSI CHB

J27

S4

MRH-D

MRH-D

P64H

S5

BIOS6

BIOS5

S2

S3

BIOS2

J3 8 COM2

BIOS1

CN4

J20

PW1

J16
J15

J13
J14

J11

Pwr Pod/ATI

J12

(top/bottom)

J9
J10

SUPER i2DML-8G2

JV1

J19

Battery

J22

S6

S1

SPKR

J21

USB2/3

ICH4

(South

Bridge)

JBT1

Fan3 Fan1

PWR Pod

(VRM)

Rage XL

®

IPMI

CPU1

J30

CPU2

J29

J31

J36

Fan2

Fan4

SNC

(North

Bridge)

J26

SIOH

I/O

J25

U66

DS3DS4

IDE2

J35

Fan5

Fan6

PW2

IDE1

J37

Notes:
Jumpers not indicated are for test purposes only.
" " indicates the location of Pin 1.
The i2DML-iG2 shares the same layout but does not include an onboard SCSI controller, SCSI
connectors or SCSI jumpers.

Warning:
The heatsink on the MRH-D chip has been pre-installed by the manufacturer. Please do not
touch it. Turning the heatsink the wrong way will damage it and void the manufacturer's
warranty.

5-14

Chapter 5: Advanced Serverboard Setup

i2DML-8G2/i2DML-iG2 Quick Reference

Jumper Description Default Setting

CN5 Power Fail Alarm Enable/Disable Closed (Disabled)
J7 GLAN Enable/Disable Pins 1-2 (Enabled)
J31 Watch Dog Pins 1-2 (Reset)
JBT1 CMOS Clear See Section 5-9
JA1* SCSI Enable/Disable Pins 1-2 (Enabled)
JV 1 VGA Enable/Disable Pins 1-2 (Enabled)

Connector Description

DS3/DS4 Debug LEDs
DS7* SCSI LEDs
Fan1 - 8 Fan1 through Fan8 Headers
J 1 Backpanel USB Ports (USB0/1)
J 2 VGA Connector
J3* SCSI Channel B Connector
J 5 COM1 Serial Port
J 6 Wake-on-Ring Header
J9 - J16** DDR Memory Sockets
J18* SCSI Channel A Connector
J19 PCI-X Bus (256-Pin Slot)
J20 24-pin Power1 Connector
J21 Front Panel USB Ports (USB2/3)
J22 System Management Bus Connector
J25 Chassis Intrusion Header
J26 IPMI 1.5, 2.0 Connector
J27 System Management Bus Power Header
J30/J29 CPU 1/2 Sockets
J31 Watch Dog Reset
J36 24-pin Power2 Connector
J37/J35 IDE1/2 Disk Drive Connectors
J38 COM2 Serial Header
S1-6 BIOS Chips
U6 2 Power Fault Connector
U66 Front Control Panel Connector

* i2DML-8G2 only
** See Section 5-5 for details on installing memory

5-15

SUPERSERVER 6113L-8/6113L-i User's Manual

5-8 Connector Definitions

EPS 12V Power Connector

There are two 24-pin main power sup­ply connectors on the serverboard.
These power connectors meet the
SSI EPS 12V specification. See the
table on the right for pin definitions.
(Only one of the two connections
need to be made.)

Processor Power
Connectors

In addition to the primary power con­nectors, a 4-pin EPS 12V/15A power
connector (from your power supply)
must be connected to each CPU
power pod (VRM). Refer to the table
on the right for pin definitions.

Power Fail LED

The Power Fail LED connection is
located on pins 5 and 6 of U66. Refer
to the table on the right for pin defi­nitions.

12V, 24-pin Power Supply Conn ector Pin

Definitions (J20, J36)

Pin Number Definition
13 +3.3V
14 -12V
15 COM
16 PS_ON#
17 COM
18 COM
19 COM
20 Res(NC)
21 +5V
22 +5V
23 +5V
24 COM

Pin Number De finition

1 +3.3V
2 +3.3V
3 COM

4 +5V

5 COM

6 +5V

7 COM

8 PWR_O K
9 5VSB
10 +12V
11 +12V
12 +3.3 V

4-Pin, 12v Power Supply

Connectors

(to power pods)

Pins

Definition

1 thru 2

Ground

3 thru 4

+12v

Power Fail LED Pin

Definitions

(U66)

Pin

Number

Definition

5

Vcc

6

GND

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20
of U66. Refer to the table on the
right for pin definitions.

Power LED

The Power LED connection is lo­cated on pins 15 and 16 of U66. Re­fer to the table on the right for pin
definitions.

5-16

NMI Button Pin

Definitions (U66)

Pin

Number

PWR_LED Pin Definitions

Number

Definition
19
20

Pin

Control

Ground

(U66)

Definition
15
16

Vcc

Control

Chapter 5: Advanced Serverboard Setup

HDD LED

The HDD LED connection is located
on pins 13 and 14 of U66. Attach the
hard drive LED cable here to display
disk activity for any hard drives on
the system. See the table on the
right for pin definitions.

NIC1 LED

The NIC (Network Interface Control­ler) LED connection for the GLAN
port is located on pins 11 and 12 of
U66. Attach the NIC LED cable to
display network activity. Refer to the
table on the right for pin definitions.

NIC2 LED

The NIC (Network Interface Control­ler) LED connection for the GLAN
port is located on pins 9 and 10 of
U66. Attach the NIC LED cable to
display network activity. Refer to the
table on the right for pin definitions.

HDD LED Pin

Definitions

(U66)

Pin

Number

13
14

NIC LED Pin

Definitions

(U66)

Pin

Number

11
12

NIC 2 LED Pin

Definitions

(U66)

Pin

Number

9

10

Definition

Vcc

HD Active

Definition

Vcc

GND

Definition

Vcc

GND

Overheat LED (OH)

Connect an LED to the OH connec­tion on pins 7 and 8 of U66 to provide
advanced warning of chassis over­heating. Refer to the table on the
right for pin definitions.

5-17

Overheat (OH) LED

Pin Definitions

(U66)

Pin

Number

Definition

7

Vcc

8

GND

SUPERSERVER 6113L-8/6113L-i User's Manual

Reset Button

The Reset Button connection is lo­cated on pins 3 and 4 of U66. Attach
it the hardware reset switch on the
computer case to these pins. Refer
to the table on the right for pin defi­nitions.

Power Button

The Power Button connection is lo­cated on pins 1 and 2 of U66. Mo­mentarily contacting both pins will
power on/off the system. This button
can also be configured to function as
a suspend button (see the appropri­ate setting in BIOS). To turn off the
power when set to suspend mode,
depress the button for at least 4 sec­onds. Refer to the table on the right
for pin definitions.

Reset Pin

Definitions

(U66)

Pin

Number

Definition

3

Reset

4

Ground

Power Button

Connector

Pin Definitions

(U66)

Pin

Definition

Number

PW_ON

1

Ground

2

Universal Serial Bus
(USB0/1)

Two USB 2.0 ports are located on
the backpanel. These are designated
USB0/1. USB0 is the bottom con­nector and USB1 is the top connec­tor of J1. See the table on the right
for pin definitions.

Universal Serial Bus Pin Definitions

USB0 USB1

Pin
Number Definition
1+5V
2P0­ 3P0+
4 Ground
5 N/A

5-18

Pin
Number Definition
1+5V
2P0­ 3P0+
4 Ground
5Key

Front Panel Universal
Serial Bus Header

Two extra USB headers (USB2/3 lo­cated at J21) can be used to provide
front side USB access. You will
need a USB cable to use either con­nection. Refer to the table on the
right for pin definitions.

Serial Ports

There are two Serial Ports on the
serverboard. The COM1 serial port
(J5) is located on the back panel and
the COM2 header (J38) is located
near the USB 2/3 connector. See
the table on the right for pin defini­tions.

Chapter 5: Advanced Serverboard Setup

Front Panel Universal Serial Bus

Pin Definitions (J21)

Pin
Number Definition
1+5V
2P0­ 3P0+
4 Ground
5Key

Serial Ports Pin Definitions

Pin Number Definition
1 DCD
2 Serial In
3 Serial Out
4 DTR
5 Ground

(J5, J38)

Pin Number Definition
6 DSR
7 RTS
8 CTS
9 RI

GLAN (Ethernet) Ports

Two G-bit Ethernet ports (designated
LAN1 and LAN2) are located be­tween USB0/1 ports and the VGA
connector. These ports accept RJ45
type cables.

Chassis Intrusion

A Chassis Intrusion header (J25) is
located near JBT1 on the
serverboard. Attach the appropriate
cable to inform you of a chassis in­trusion. See the table on the right
for pin definitions.

5-19

Chassis Intrusion

Pin Definitions

(J25)

Pin

Definition

Number

Instrusion

1

Ground

2

SUPERSERVER 6113L-8/6113L-i User's Manual

Fan Headers

The i2DML-8G2/i2DML-iG2 has eight
fan headers, designated Fan1
through Fan8. See the table on the
right for pin definitions.

Power Fault

Connect a cable from your power
supply to the U62 header to provide
warning of power supply failure. This
warning signal is passed through the
PWR_LED pin on U66 to indicate a
power failure on the chassis. See
the table on the right for pin defini­tions.

Note: This feature is only available when
using redundant Supermicro power sup­plies.

Fan Header Pin Definitions

(Fan1-Fan8)

Pin

Number

1
2
3

Caution: Fan headers are DC power.

Definition

Ground (black)

+12V (red)

Tachometer

Power Fault Pin Definitions

Number

Pin

1
2
3
4

(U62)

Definition
P/S 1 Fail Signal
P/S 2 Fail Signal
P/S 3 Fail Signal

Reset (from MB)

Wake-On-Ring

The Wake-On-Ring header is desig­nated J6. This function allows your
computer to receive and "wake-up"
from an incoming call to the modem
when in suspend state. See the
table on the right for pin definitions.
You must have a Wake-On-Ring card
and cable to use this feature.

5-20

Wake-on-Ring

Pin Definitions

(J6)

Pin

Number

Definition

1

Ground

2

Wake-up

Chapter 5: Advanced Serverboard Setup

SMB

A System Management Bus header
is located at J22. Connect the ap­propriate cable here to utilize SMB
on your system.

SMB Power (I2C)
Connector

The I2C connector at J27, located be­tween the PWR ForceOn Header and
the PWR Fault header, monitors the
status of the power supply, the fans,
and the system temperature.

SMB Header Pin Definitions

Pin

Number

(J22)

1
2
3
4

SMB PWR Pin Definitions

Pin #

1
2
3
4
5

Definition

Data

Ground

Clock

No Connection

(J27)

Definition

Clock

Data

N/A
N/A
N/A

5-21

SUPERSERVER 6113L-8/6113L-i User's Manual

5-9 Jumper Settings

Explanation of
Jumpers

To modify the operation of the
serverboard, jumpers can be used
to choose between optional
settings. Jumpers create shorts
between two pins to change the
function of the connector. Pin 1
is identified with a square solder
pad on the printed circuit board.
See the serverboard layout page
for jumper locations.

Note: On two pin jumpers,
"Closed" means the jumper is on
and "Open" means the jumper is
off the pins.

CMOS Clear

Connector

Pins

Jumper

Cap

Setting

3 2 1

3 2 1

Pin 1-2 short

JBT1 is used to clear CMOS (which will also clear any passwords). Instead of
pins, this jumper consists of contact pads to prevent accidentally clearing the
contents of CMOS.
To clear CMOS, first power down the system, then

1) Unplug the power cord(s)

2) With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver

3) Remove the screwdriver (or shorting device)

4) Reconnect the power cord(s) and power on the system.

Note: Do not use the PW_ON connector to clear CMOS.

VGA Enable/Disable

JV1 allows you to enable or disable
the VGA port. The default position is
on pins 1 and 2 to enable VGA. See

VGA Enable/Disable

Jumper Settings

(JV1)

Jumper

Position

1-2
2-3

Definition

Enabled
Disabled

the table on the right for jumper set­tings.

5-22

Chapter 5: Advanced Serverboard Setup

GLAN Enable/Disable

Change the setting of jumper J7 to
enable or disable the onboard GLAN
ports (GLAN1 and GLAN2) on the
serverboard. See the table on the
right for jumper settings. The default
setting is enabled

Watch Dog Enable/Disable

J31 controls Watch Dog, a system
monitor that takes action when a soft­ware application freezes the system.
Jumping pins 1-2 will have WD reset
the system if a program freezes.
Jumping pins 2-3 will generate a non­maskable interrupt for the program
that has frozen (requires software
implementation). Watch Dog must
also be enabled in BIOS.

GLAN

Enable/Disable

Jumper Settings

(J7)

Jumper

Position
Pins 1-2
Pins 2-3

Jumper Settings (J31)

Jumper
Position
Pins 1-2
Pins 2-3

Open

Definition

Enabled

Disabled

Watch Dog

Definition

WD to Reset

WD to NMI

Disabled

Power Fail Alarm Enable/
Disable

The system will notify you in the
event of a power supply failure. This
feature assumes that redundant
Supermicro power supply units are
installed in the chassis. If you only
have a single power supply installed,
you should disable this (the default
setting) with CN5 to prevent false
alarms. See the table on the right for
jumper settings.

5-23

Alarm Reset

Jumper Settings

(CN5)

Jumper

Position

Open

Closed

Definition

Enabled

Disabled

SUPERSERVER 6113L-8/6113L-i User's Manual

SCSI Enable/Disable
(6113L-8 only)

The SCSI jumper at JA1 allows you to
enable or disable the onboard SCSI
controller. The normal (default) posi­tion is on pins 1-2 to enable SCSI ter­mination. See the table on the right
for jumper settings.

5-10 Onboard Indicators

SCSI Enable/Disable

Jumper Settings

(JA1)

Jumper

Position
Pins 1-2
Pins 2-3

Definition

Enabled

Disabled

GLAN LEDs

Each of the Gigabit Ethernet LAN
ports (located beside the COM2 port
on the back panel) has two LEDs.
The yellow LED indicates activity
while the other LED may be green,
orange or off to indicate the speed of
the connection. See the table at right
for the functions associated with the
second LED.

Debug LEDs

There are two debug LEDs located
next to the IDE 2 Connector to indi­cate common debug messages.
See the table below for the functions
associated with the debug LEDs.

Debug LED Indications

DS3 DS4
On On
Off On
On Off
Off Off

Indication
SNC found and start memory sizing
Initial system memory and SIOH
Valid memory and SIOH found
ICH4 found

(DS3, DS4)

Gb LAN Right LED

Indicator

LED

Color

Green

Orange

Off

Definition

No Connection

100 Mb

1 Gb

5-24

Chapter 5: Advanced Serverboard Setup

SCSI Activity LED
(6113L-8 only)

The SCSI Activity LED is located
next to the LSI SCSI controller.
When the SCSI Activity LED blinks,
it indicates that one or both of the
SCSI channels are active.

5-11 SCSI and IDE Disk Drive Connections

When connecting the hard disk drive cables, please note that a red mark on a
wire typically designates the location of pin 1.

IDE Connectors

There are no jumpers to con­figure the onboard IDE#1 and
#2 connectors. See the table
below for pin definitions.

IDE Connector Pin Definitions

Pin Number Function
1 Reset IDE
3 Host Data 7
5 Host Data 6
7 Host Data 5
9 Host Data 4
11 Host Data 3
13 Host Data 2
15 Host Data 1
17 Host Data 0
19 GND
21 DRQ3
23 I/O Write­ 25 I/O Read­ 27 IOCHRDY
29 DACK3­ 31 IRQ14
33 Addr 1
35 Addr 0
37 Chip Select 0
39 Activity

(J37, J35)

5-25

Pin Number Function
2 GND
4 Host Data 8
6 Host Data 9
8 Host Data 10
10 Host Data 11
12 Host Data 12
14 Host Data 13
16 Host Data 14
18 Host Data 15
20 Key
22 GND
24 GND
26 GND
28 BALE
30 GND
32 IOCS16­ 34 GND
36 Addr 2
38 Chip Select 1­ 40 GND

SUPERSERVER 6113L-8/6113L-i User's Manual

Ultra320 SCSI Connectors
(6113L-8 only)

Refer to the table below for the pin
definitions of the Ultra320 SCSI
connectors at J18 (SCSI channel A
and J3 (SCSI channel B).

68-pin Ultra 320 SCSI Connectors (J3 and J18)

Connector

Contact
Number

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

Signal Names

+DB(12)
+DB(13)
+DB(14)
+DB(15)

+DB(P1)

+DB(0)
+DB(1)
+DB(2)
+DB(3)
+DB(4)
+DB(5)
+DB(6)
+DB(7)
+DB(P)

GROUND
DIFFSENS
TERMPWR
TERMPWR

RESERVED

GROUND

+ATN

GROUND

+BSY
+ACK
+RST
+MSG
+SEL
+C/D
+REQ

+I/O
+DB(8)
+DB(9)

+DB(10)
+DB(11)

Connector

Contact
Number

Signal Names

35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68

-DB(12)

-DB(13)

-DB(14)

-DB(15)

-DB(P1)

-DB(0)

-DB(1)

-DB(2)

-DB(3)

-DB(4)

-DB(5)

-DB(6)

-DB(7)

-DB(P)
GROUND
GROUND

TERMPWR
TERMPWR

RESERVED

GROUND

-ATN

GROUND

-BSY

-ACK

-RST

-MSG

-SEL

-C/D

-REQ

-I/O

-DB(8)

-DB(9)

-DB(10)

-DB(11)

5-26

Chapter 6: Advanced Chassis Setup

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform
maintenance on the SC813HS-500/SC813Hi-500 chassis. For component instal­lation, follow the steps in the order given to eliminate the most common problems
encountered. If some steps are unnecessary, skip ahead to the next step.

Tools Required

The only tool you will need to install components and perform maintenance
is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electricstatic discharge (ESD) can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally sufficient to protect your equip­ment from ESD damage.

Precautions

! Use a grounded wrist strap designed to prevent static discharge.

! Touch a grounded metal object before removing any board from its antistatic

bag.

! Handle a board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

! When handling chips or modules, avoid touching their pins.

! Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

! For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

6-1

SUPERSERVER 6113L-8/6113L-i User's Manual

CD-ROM Drive USB Ports

COM Port

USB Ports

Figure 6-1. Chassis: Front and Rear Views

Control Panel/System LEDs

System Reset

VGA Port

Ethernet PortsCOM1 Port

PCI-X Slot

External SCSI Port

Main PowerSCSI/IDE Drives

(6113L-8 only)

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected
to the JF2 connector on the serverboard to provide you with system status
indications. A ribbon cable has bundled these wires together to simplify the
connection. Connect the cable from JF2 on the serverboard to the appro­priate header on the Control Panel PCB (printed circuit board). Make sure
the red wire plugs into pin 1 on both connectors. Pull all excess cabling out
of the airflow path.

The control panel LEDs inform you of system status. See "Chapter 3:
System Interface" for details on the LEDs and the control panel buttons.
Details on JF2 can be found in "Chapter 5: Advanced Serverboard Setup."

6-2

Chapter 6: Advanced Chassis Setup

6-3 System Fans

Two 10-cm blower fans and a high-speed 4-cm fan provide all the cooling needed
for the SuperServer 6113L-8/6113L-i. It is very important that the chassis top
cover is properly installed and making a good seal for the cooling air to circulate
properly through the chassis and cool the components. See Figure 6-2.

System Fan Failure

If a fan fails, the ambient air temperature in the chassis will rise and activate the
overheat LED on the control panel. Replace any failed fan immediately with the
same type and model. You must power down the system before replacing any
fan (removing the power cord is also recommended as a safety precaution).

Replacing System Fans

1. Removing a 10-cm fan:

After turning off the power to the system, first remove the chassis cover
and unplug the fan cable from the serverboard. Unscrew the failed blower fan
from the chassis and pull it completely out of the chassis.

2. Installing a new 10-cm fan:

Replace the failed fan with an identical 10-cm, 12 volt fan (available from
Supermicro, p/n FAN-0059). Install the new fan in its proper place in the
chassis by positioning it on the two mounting posts. Secure the fan to
the chassis with the screws you removed previously, then attach the fan
wires to the correct chassis fan header. Make sure the air seal under the fan
is properly installed and creating a good seal. Power up the system and
check that the fan is working properly and that the LED on the control panel
has turned off. Finish by replacing the chassis cover.

3. Removing a 4-cm fan:

After turning off the power to the system, first remove the chassis cover and
unplug the fan cable from the serverboard. Unscrew the fan and then remove
it from the chassis.

4. Installing a new 4-cm fan:

Replace the failed fan with an identical 4-cm fan (available from Supermicro,
p/n FAN-0061). Install the new fan in the same position as the failed one
you just removed and secure it with the screws you removed previously.
Attach the fan wires to the correct chassis fan header then power up the
system and check that the fan is working properly and that the LED on the
control panel has turned off. Finish by replacing the chassis cover.

6-3

SUPERSERVER 6113L-8/6113L-i User's Manual

10-cm Blower Fans

4-cm Cooling Fan

Figure 6-2. System Cooling Fans

6-4 Drive Bay Installation/Removal

Removing the Front Bezel

If your system has a front bezel (optional) attached to the chassis, you
must first remove it to gain access to the drive bays. To remove the bezel,
first unlock the front of the chassis then press the release knob (see Figure
6-3). Carefully remove the bezel with both hands. A filter located within the
bezel can be removed for replacement/cleaning. It is recommended that you
keep a maintenance log of filter cleaning/replacement, since its condition
will affect the airflow throughout the whole system.

6-4

Figure 6-3. Removing the Front Bezel

Accessing the Drive Bays

Chapter 6: Advanced Chassis Setup

1. Unlock

2. Press release knob

3. Remove bezel assembly

SCSI/IDE Drives: Because of their hotswap capability, you do not need to access
the inside of the chassis or power down the system to install or replace SCSI
drives. Proceed to the next step for instructions. (For installing/removing IDE
drives, you do not need to access the inside of the system but you will need to
remove power from the system first.)

CD-ROM Drive: For installing/removing a CD-ROM drive, you will need to gain
access to the inside of the 6113L-8/6113L-i by removing the top cover of the
chassis. Proceed to the "CD-ROM Drive Installation" section later in this chapter
for instructions.
Note: Only a "slim" CD-ROM drive will fit into the 6113L-8/6113L-i.

6-5

SUPERSERVER 6113L-8/6113L-i User's Manual

SCSI/IDE Drive Installation

1. Mounting a SCSI/IDE drive in a drive carrier:

The SCSI/IDE drives are mounted in drive carriers to simplify their installation
and removal from the chassis. These carriers also help promote proper
airflow for the SCSI/IDE drive bays. For this reason, even empty carriers
without SCSI/IDE drives installed must remain in the chassis. To add a new
SCSI/IDE drive, install a drive into the carrier with the printed circuit board
side toward the carrier so that the mounting holes align with those in the
carrier. Secure the drive to the carrier with four screws, as shown in Figure
6-4.

Figure 6-4. Mounting a SCSI/IDE Drive in a Carrier

6113L-8 only: Use caution when working around the SCSI

!

!

backplane. Do not touch the backplane with any metal ob­jects and make sure no ribbon cables touch the backplane or
obstruct the holes, which aid in proper airflow.

Important: Regardless of how many SCSI/IDE hard drives
are installed, all SCSI/IDE drive carriers must remain in the
drive bays for proper airflow.

6-6

Chapter 6: Advanced Chassis Setup

2. Installing/removing hot-swap SCSI drives (6113L-8 only):

The SCSI drive bays are located in the front of the chassis, making them
easily accessible for installation and removal. The SCSI drives are hot-swap
units, meaning that they can be installed and removed while the system is
running. To remove a SCSI drive, first push the colored release button
located beside the drive's LEDs, then swing the handle fully out and use it to
pull the SCSI drive carrier straight out (see Figure 6-5).

Figure 6-5. Removing SCSI Drives

Important: All of the SCSI drive carriers must remain in

!

the drive bays to maintain proper cooling airflow.

6-7

SUPERSERVER 6113L-8/6113L-i User's Manual

CD-ROM Drive Installation

The top cover of the chassis must be opened to gain full access to the CD-ROM
drive bay. The 6113L-8/6113L-i accomodates only slim CD-ROM drives. Side
mounting brackets are needed to mount a slim CD-ROM drive in the 6113L-8/
6113L-i server.

You must power down the system before installing or removing a CD-ROM drive.
First, release the retention screws that secure the server unit to the rack. Grasp
the two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover and at the same time, push the cover away from you until
it stops. You can then lift the top cover from the chassis to gain full access to
the inside of the server.

With the chassis cover removed, unplug the power and data cables from the drive.
Then locate the locking tab at the rear of the drive. It will be on the left side of
the drive when viewed from the front of the chassis. Pull the tab away from the
drive and push the drive unit out the front of the chassis. Add a new drive by
following this procedure in reverse order. You may hear a faint *click* of the
locking tab when the drive is fully inserted. Remember to reconnect the data and
power cables to the drive before replacing the chassis cover and restoring power
to the system.

6-8

Chapter 6: Advanced Chassis Setup

6-5 Power Supply

The SuperServer 6113L-8/6113L-i has a single 500 watt power supply, which is
auto-switching capable. This enables it to automatically sense and operate with
either a 100v or 240v input voltage. An amber light will be illuminated on the
power supply when the power is off. An illuminated green light indicates that the
power supply is operating.

Power Supply Failure

If the power supply unit fails, the system will shut down and you will need to
replace the unit. Replacement units can be ordered directly from Supermicro
(see contact information in the Preface). As there is only one power supply unit
in the 6113L-8/6113L-i, power must be completely removed from the server before
removing and replacing the power supply unit for whatever reason.

Removing/Replacing the Power Supply

1. Removing the power supply:

First turn the power switch on the control panel off, then unplug the
power cord from the system. Remove the chassis cover by pressing the
two release buttons on the top of the chassis (near the front) and push
the chassis top rearward about one inch. To remove the failed power
unit, push the beige colored release tab to the right and then carefully lift
the unit up about 1/2 inch only. If you lift too high, you may damage the
power distribution board that the other end of the unit is connected to.
Then, pull the power unit straight back to unplug it from the power
distribution board. See Figure 6-6.

2. Installing a new power supply:

Replace the failed unit with another unit of the same input voltage, output
voltage and wattage. It is highly recommended to replace it with exactly
the same model power supply (Supermicro part number: PWS-0048).
Carefully insert the new unit into position to plug it into the power distribution
board, making sure you are not holding it at too great an angle, which may
damage the power distribution board. Push it completely into the power
distribution board and seat it in the chassis. When correctly installed it
should be laying flat - make sure the end of the power supply is not sitting
on the stop in the chassis. Reconnect the power cord, replace the chassis
top cover and reposition the unit back into the rack. Finish by depressing
the power button on the chassis front control panel.

6-9

SUPERSERVER 6113L-8/6113L-i User's Manual

Figure 6-6. Removing/Replacing the Power Supply

6-10

Chapter 7: BIOS

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMIBIOS settings for the i2DML-8G2/i2DML-iG2. The
AMI ROM BIOS is stored in a Flash EEPROM and can be easily upgraded using
a floppy disk-based program.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup Utility screens, hit the <Delete> key while the
system is booting-up. (In most cases, the <Delete> key is used to invoke the BIOS
setup screen. There are a few cases when other keys are used, such as <F1> or
<F2>.)

Each BIOS menu option is described in this chapter. The BIOS setup menu
screen has two main frames. The left frame displays all the setting options;
“grayed-out” options cannot be configured while those in blue can be configured
by the user. The right frame displays the key legend. Above the key legend is
an area reserved for a text message to describe the highlighted setting. (AMIBIOS
has default text messages built in. Supermicro retains the option to include,
omit, or change any of these text messages.) When an option is selected in the
left frame, it is highlighted in white. Press the <Tab> key or the <Arrow> keys
to move between fields. Certain "hot keys" may also be used. Most of the BIOS
these hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and so on.

Options printed in Bold are default settings.

Normally, the only visible POST (Power On Self Test) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu
of the BIOS Setup utility. From the main menu, you can access the other setup
screens, such as the Chipset and Power menus. Section 7-3 gives detailed
descriptions of each parameter setting in the Setup utility.

An AMIBIOS identification string is displayed at the left bottom corner of the
screen, below the copyright message.

7-1

SUPERSERVER 6113L-8/6113L-i User's Manual

7-2 Main Setup Screen

When you first enter the BIOS Setup Utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on
the top of the screen. The Main BIOS Setup screen is shown below.

When you select the Main Setup, the AMI BIOS Version, BIOS Build Date,
BIOS ID and System Memory will all be displayed.

Language Menu

This option allows you to set the default Language used by the BIOS.
Select English (US) if you wants to use English as your default Language.

BSP Information

When you select this option, AMI BIOS will automatically display the status
of each of the following items: BSP Type, BSP Speed, BSP CPU1 ID, BSP
CPU2 ID, BSP L1 Cache, BSP L2 Cache and BSP L3 Cache.

System Time/System Date

Use this option to change the system time and date. Highlight System Time or
System Date using the <Arrow> keys. The date must be entered in MM/DD/

YYYY format. The time is entered in HH:MM:SS format. (The time follows the
24-hour format. For example, 5:30 A.M. appears as 05:30:00 and 5:30 P.M. as
17:30:00.)

7-2

Chapter 7: BIOS

7-3 Advanced Setup Screen

Selecting the Advanced tab takes you to the Advanced setup screen. The
Advanced BIOS Setup screen and sub menus are listed below:

When you first enter the Advanced Setup screen, the Setup Warning will be
displayed. Please follow the instructions and set the correct value for each
item to prevent the system from malfunctioning.

!!

!Super IO Configuration

!!

7-3

SUPERSERVER 6113L-8/6113L-i User's Manual

Serial Port1 Address/Serial Port2 Address

This option specifies the base I/O port addresses and Interrupt Request
addresses of Serial Port 1 and Serial Port2. Select "Disabled" to prevent the
serial ports from accessing any system resources. When this option is set
to Disabled, the serial ports become physically unavailable. The options are
"Enabled" and "Disabled." The default setting for Serial Port1 is "Enabled".
When "Enabled" is selected for Serial Port1, the address for Serial Port1 will
be automatically set to 2F8/IRQ3. The default setting for Serial Port2 is
"Disabled". When "Disabled" is selected for Serial Port2, Serial Port2 will
become physically unavailable.

!!

!IDE Configuration

!!

The screen for the Primary IDE Master is shown below.

When you select this Sub Menu, AMI BIOS automatically displays the status
of the following items: Device, Vendor, Size, LBA Mode, PIO Node, Asynch
DMA, UltraDMA and S.M.A.R.T.

7-4

Chapter 7: BIOS

Primary IDE Master/Slave, Secondary IDE Master/Slave

From the Advanced Setup screen, press <Enter> on the appropriate option to
access primary and secondary IDE master and slave drives submenu. Use this
screen to select options for the Primary and Secondary IDE drives. Use the up
and down <Arrow> keys to select an item and the <Plus> and <Minus> keys to
change the value of the selected option.

Type

Select the type of device connected to the system. The options are "Not In­stalled", "Auto", "CDROM" and "ARMD".

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive.
In LBA mode, the maximum drive capacity is 137 GB. For drive capacities over
137 GB, your system must be equipped with 48-bit LBA mode addressing. If not,
contact your manufacturer or install an ATA/133 IDE controller card that supports
48-bit LBA mode. The options are "Disabled" and "Auto".

Block (Multi-Sector Transfer)

Block mode boosts IDE drive performance by increasing the amount of data
transferred. Only 512 bytes of data can be transferred per interrupt if block mode
is not used. Block mode allows transfers of up to 64 KB per interrupt. Select
"Disabled" to allow the data to be transferred from and to the device one sector
at a time. Select "Auto" to allows the data transfer from and to the device occur
multiple sectors at a time if the device supports it. The options are "Auto" and
"Disabled".

PIO Mode

IDE PIO (Programmable I/O) mode programs timing cycles between the IDE drive
and the programmable IDE controller. As the PIO mode increases, the cycle time
decreases. The options are "Auto", "0", "1", "2", "3" and "4". Select Auto for
BIOS to auto detect the PIO mode. Use this value if the IDE disk drive support
cannot be determined. Select 0 for BIOS to use PIO mode 0, 1 for PIO mode 1,
2 for PIO mode 2, 3 for PIO mode 3 or 4 for PIO mode 4. These settings have
data transfer rates of 3.3 MBs, 5.2 MBs, 8.3 MBs, 11.1 MBs and 16.6 MBs,
respectively. This setting generally works with all hard disk drives manufactured
after 1999. For other disk drives, such as IDE CD-ROM drives, check the speci­fications of the drive.

7-5

SUPERSERVER 6113L-8/6113L-i User's Manual

DMA Mode

Select the default setting of Auto to allow the BIOS to auto detect the DMA
mode. Use this value if the IDE disk drive support cannot be determined. Other­wise, select from one of the following options: SWDMA0 (Single Word DMA mode
0, 2.1 MBs data transfer rate), SWDMA1 (Single Word DMA mode 1, 4.2 MBs
data transfer rate), SWDMA2 (Single Word DMA mode 2, 8.3 MBs data transfer
rate), MWDMA0 (Multi Word DMA mode 0, 4.2 MBs data transfer rate), MWDMA1
(Multi Word DMA mode 1, 13.3 MBs data transfer rate), MWDMA2 (Single Word
DMA mode 2, 16.6 MBs data transfer rate), UDMA0 (Ultra DMA mode 0, 16.6
MBs data transfer rate), UDMA0 (Ultra DMA mode 0, 16.6 MBs data transfer
rate), UDMA1 (Ultra DMA mode 1, 25 MBs data transfer rate), UDMA2 (Ultra
DMA mode 2, 33.3 MBs data transfer rate), UDMA3 (Ultra DMA mode 3, 66.6
MBs data transfer rate) or UDMA4 (Ultra DMA mode 4, 100 MBs data transfer
rate).

S.M.A.R.T. For Hard disk drives

Self-Monitoring Analysis and Reporting Technology (SMART) can help predict
impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk
drive support. Select "Disabled" to prevent the BIOS from using the S.M.A.R.T.
Select "Enabled" to allow the BIOS to use the S.M.A.R.T. to support hard drive
disk.

32-Bit Data Transfer

Select "Enabled" to activate the 32-Bit data transfer function. Select "Disabled"
to deactivate the function.

ARMD Emulation Type

This feature allows the BIOS to set the ARMD Emulation type. The options are

"Auto", "Floppy" and "Hard Disk."

ATA(PI) Detect Time Out

The feature allows BIOS to set the time out value for detecting ATA(PI) devices.
The options are "0", "5", "10", "15", "20", "25" and "30."

7-6

Chapter 7: BIOS

ATA(PI) 80-Pin Cable Detection

This feature allows the BIOS to auto-detect the 80-pin ATA(PI) Cable. The
options are "Host & Device", "Host" and "Device."

!!

!BIOS Settings Configuration

!!

This item allows the user to configure the system's boot settings.

Quiet Boot

Set this value to allow the boot up screen options to be modified between POST
messages or OEM logo. Select Disabled to allow the computer system to
display the POST messages. Select Enabled to allow the computer system to
display the OEM logo.

7-7

SUPERSERVER 6113L-8/6113L-i User's Manual

!System Health Monitor

This feature allows the BIOS to automatically display the status of the following
items: CPU Overheat Temperature, CPU1/CPU2 Temperature, various voltage
levels and fan speeds. See screen shot below.

7-8

Chapter 7: BIOS

!

Peripheral Device Configuration

This screen allows the user to configure the Peripheral Device settings

Power Loss Control

This setting allows you to choose how the system will react when power is
returned to the system after being unexpectedly lost. Options are "Stay Off",
"Power On" and "Last State."

Watch Dog Timer

This setting is used to enable or disabled the Watch Dog Timer function. It
must be used in conjunction with the J31 jumper (see Chapter 2 for details).
Options are "Enabled" and "Disabled."

Watch Dog Timer Value

If the function of Watch Dog Timer (above) is enabled, this feature will allow
the user to value for the Watch Dog Timer. Options are "2 Min(utes)", "5 Min.",
"10 Min." and "15 Min."

7-9

SUPERSERVER 6113L-8/6113L-i User's Manual

!USB Configuration

This feature allows the user to configure the USB settings.

USB Function

Select "Enabled" to enable the USB Host Controller. The options are
"Disabled" and "Enabled."

Legacy USB Support

Select "Enabled" to enable support for USB Legacy. The options are
"Disabled" and "Enabled."

7-10

7-4 PCI/PnP Configuration

This feature allows the user to set the PCI/PnP configuration.

Chapter 7: BIOS

PCI Latency Timer

This option sets the latency time for all PCI devices on the PCI bus. The default
setting is "64." Select one of the following to set latency to the desired number
of PCI clock cycles: "32", "64", "96", "128", "160", "192", "224" and "248" (clock
cycles).

Allocate IRQ to PCI VGA

Set this value to allow or restrict the system from assigning an interrupt request
address to the VGA adapter card. The options are "Yes" and "No".

PCI IDE BusMaster

Set this value to allow or prevent the use of PCI IDE busmastering. "Enabled"
allows the BIOS to use PCI busmaster for reading and writing to IDE drives. The
options are "Disabled" and "Enabled".

PCI Slot1 Option ROM

Select "Enabled" to enable the PCI Slot1 Option ROM function. The options are
"Disabled" and "Enabled".

7-11

SUPERSERVER 6113L-8/6113L-i User's Manual

!Hardware Health Monitoring

H/W Health Function

Select "Enabled" to enable the Hardware Health Monitoring function. The
options are "Enabled" and "Disabled".

Overheat Temperature Trips

This feature allows the user to set the CPU temperature threshold. The
options range from "65oC" to "90oC. The default setting is "78oC".

7-5 Security Settings

BIOS provides a Supervisor and a User password. If you use both passwords,
the Supervisor password must be set first.

Change Supervisor Password

Select this option and press <Enter> to access the submenu, then type in the
password.

7-12

Chapter 7: BIOS

Change User Password

Select this option and press <Enter> to access the submenu, then type in the
password.

Clear User Password

Select this option and press <Enter> to access the submenu. You can use the
sub menu to clear the user password.

7-6 Exit Options

Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS
Setup screen.

Exit Saving Changes

When you have completed the system configuration changes, select this option
and press <Enter> to leave the BIOS Setup and boot the computer to allow the
new system configuration parameters to take effect.

Exit Discarding Changes

Select this option and press <Enter> to quit the BIOS Setup without making any
permanent changes to the system configuration and boot the computer.

7-13

SUPERSERVER 6113L-8/6113L-i User's Manual

Load Optimal Defaults

Select Load Optimal Defaults from the Exit menu and press <Enter> then "OK"
to have BIOS automatically load all Optimal Defaults for the BIOS settings. The
optimal settings are designed for maximum system performance, but may not
work best for all computer applications.

Load Fail-Safe Defaults

To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but
not maximum performance.

Discard Changes

Select this option and press <Enter> to discard any changes made and return
to the BIOS Utility Program.

7-14

Appendix A: BIOS Error Beep Codes

Appendix A

BIOS Error Beep Codes

During the POST (Power-On Self-Test) routines, which are performed each
time the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to
continue the boot-up process. The error messages normally appear on
the screen.

Fatal errors are those which will not allow the system to continue the
boot-up procedure. If a fatal error occurs, you should consult with your
system manufacturer for possible repairs.

These fatal errors are usually communicated through a series of audible
beeps. The numbers on the fatal error list, on the following page,
correspond to the number of beeps for the corresponding error. All
errors listed, with the exception of Beep Code 8, are fatal errors.

POST codes may be read on the debug LEDs located beside the LAN port
on the serverboard backplane. See the description of the Debug LEDs (LED1
and LED2) in Section 2-6.

A-1 IA-32 Error Beep Codes

Beep Code Error Message Description

1 beep Refresh Circuits have

been reset. (Ready to
power up.)

5 short, 1 long Memory error No memory detected in

system

8 beeps Display memory read/write error Video adapter missing or

with faulty memory

A-1

SUPERSERVER 6113L-8/6113L-i User's Manual

A-2 IA-64 Common Debug Codes

Common Debug Codes for IA-64 systems are listed below:

Checkpoints Code Description

DS4 DS3
On On: SNC found and start memory sizing
On Off: Initial system memory and SIOH
Off On: Valid memory and SIOH found
Off Off: ICH4 found

Note: The debug code LEDs (DS3 and DS4) are located next to the IDE2 connector.
Please refer to the serverboard layout in Chapter 5 for DS3 and DS4 locations.

A-2

Appendix B: BIOS POST Codes

Appendix B

BIOS POST Codes

When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O
port 0080h. If the computer cannot complete the boot process, diagnostic equipment
can be attached to the computer to read I/O port 0080h.

Checkpoint Code Description

D0h The NMI is disabled. Power on delay is starting. Next, the initialization

code checksum will be verified.

D1h Initializing the DMA controller, performing the keyboard controller

BAT test, starting memory refresh, and entering 4 GB flat mode next.

D3h Starting memory sizing next.

D4h Returning to real mode. Executing any OEM patches and setting the

Stack next.

D5h Passing control to the uncompressed code in shadow RAM at

E000:0000h. The initialization code is copied to segment 0 and control
will be transferred to segment 0.

D6h Control is in segment 0. Next, checking if <Ctrl> <Home> was pressed

and verifying the system BIOS checksum. If either <Ctrl> <Home>
was pressed or the system BIOS checksum is bad, next will go to
checkpoint code E0h. Otherwise, going to checkpoint code D7h.

B-1

SUPERSERVER 6113L-8/6113L-i User's Manual

Checkpoint Code Description

03h The NMI is disabled. Next, checking for a soft reset or a power on

condition.
05h The BIOS stack has been built. Next, disabling cache memory.
06h Uncompressing the POST code next.
07h Next, initializing the CPU and the CPU data area.
08h The CMOS checksum calculation is done next.
0Ah The CMOS checksum calculation is done. Initializing the CMOS status

register for date and time next.
0Bh The CMOS status register is initialized. Next, performing any required

initialization before the keyboard BAT command is issued.
0Ch The keyboard controller input buffer is free. Next, issuing the BAT

command to the keyboard controller.
0Eh The keyboard controller BAT command result has been verified.

Next, performing any necessary initialization after the keyboard

controller BAT command test.

0Fh The initialization after the keyboard controller BAT command test is

done. The keyboard command byte is written next.

10h The keyboard controller command byte is written. Next, issuing the

Pin 23 and 24 blocking and unblocking command.
11h Next, checking if <End or <Ins> keys were pressed during power on.

Initializing CMOS RAM if the Initialize CMOS RAM in every boot

AMIBIOS POST option was set in AMIBCP or the <End> key was

pressed.

12h Next, disabling DMA controllers 1 and 2 and interrupt controllers 1 and

2.

13h The video display has been disabled. Port B has been initialized. Next,

initializing the chipset.
14h The 8254 timer test will begin next.
19h The 8254 timer test is over. Starting the memory refresh test next.

1Ah The memory refresh line is toggling. Checking the 15 second on/off

time next.

2Bh Passing control to the video ROM to perform any required configu-

ration before the video ROM test.

2Ch All necessary processing before passing control to the video ROM

is done. Looking for the video ROM next and passing control to it.
2Dh The video ROM has returned control to BIOS POST. Performing any

required processing after the video ROM had control.
23h Reading the 8042 input port and disabling the MEGAKEY Green

PC feature next. Making the BIOS code segment writable and

performing any necessary configuration before initializing the

interrupt vectors.

B-2

Appendix B: BIOS POST Codes

Checkpoint Code Description

24h The configuration required before interrupt vector initialization

has completed. Interrupt vector initialization is about to begin.

25h Interrupt vector initialization is done. Clearing the password if the

POST DIAG switch is on.
27h Any initialization before setting video mode will be done next.
28h Initialization before setting the video mode is complete. Configuring

the monochrome mode and color mode settings next.
2A h Bus initialization system, static, output devices will be done next, if

present. See the last page for additional information.
2Eh Completed post-video ROM test processing. If the EGA/VGA

controller is not found, performing the display memory read/write

test next.

2Fh The EGA/VGA controller was not found. The display memory read/

write test is about to begin.

30h The display memory read/write test passed. Look for retrace

checking next.

31h The display memory read/write test or retrace checking failed.

Performing the alternate display memory read/write test next.

32h The alternate display memory read/write test passed. Looking for

alternate display retrace checking next.
34h Video display checking is over. Setting the display mode next.
37h The display mode is set. Displaying the power on message next.

38h Initializing the bus input, IPL, general devices next, if present. See the

last page of this chapter for additional information.

39h Displaying bus initialization error messages. See the last page of this

chapter for additional information.

3Ah The new cursor position has been read and saved. Displaying the

Hit <DEL> message next.

3Bh The Hit <DEL> message is displayed. The protected mode memory

test is about to start.
40h Preparing the descriptor tables next.

42h The descriptor tables are prepared. Entering protected mode for the

memory test next.

43h Entered protected mode. Enabling interrupts for diagnostics mode

next.

44h Interrupts enabled if the diagnostics switch is on. Initializing data to

check memory wraparound at 0:0 next.

45h Data initialized. Checking for memory wraparound at 0:0 and finding

the total system memory size next.

46h The memory wraparound test is done. Memory size calculation has

been done. Writing patterns to test memory next.

B-3

SUPERSERVER 6113L-8/6113L-i User's Manual

Checkpoint Code Description

47 h The memory pattern has been written to extended memory. Writing

patterns to the base 640 KB memory next.

48 h Patterns written in base memory. Determining the amount of memory

below 1 MB next.

49h The amount of memory below 1 MB has been found and verified.

Determining the amount of memory above 1 MB memory next.

4Bh The amount of memory above 1 MB has been found and verified.

Checking for a soft reset and clearing the memory below 1 MB for
the soft reset next. If this is a power on situation, going to checkpoint
4Eh next.

4Ch The memory below 1 MB has been cleared via a soft reset. Clearing

the memory above 1 MB next.

4Dh The memory above 1 MB has been cleared via a soft reset. Saving

the memory size next. Going to checkpoint 52h next.

4Eh The memory test started, but not as the result of a soft reset.

Displaying the first 64 KB memory size next.

4Fh The memory size display has started. The display is updated during

the memory test. Performing the sequential and random memory test
next.

50h The memory below 1 MB has been tested and initialized. Adjusting

the displayed memory size for relocation and shadowing next.

51h The memory size display was adjusted for relocation and shadow-

ing.
Testing the memory above 1 MB next.

52h The memory above 1 MB has been tested and initialized. Saving

the memory size information next.

53h The memory size information and the CPU registers are saved.

Entering real mode next.

54h Shutdown was successful. The CPU is in real mode. Disabling the

Gate A20 line, parity, and the NMI next.

57h The A20 address line, parity, and the NMI are disabled. Adjusting

the memory size depending on relocation and shadowing next.

58h The memory size was adjusted for relocation and shadowing.

Clearing the Hit <DEL> message next.

59h The Hit <DEL> message is cleared. The <WAIT...> message is

displayed. Starting the DMA and interrupt controller test next.

B-4

Appendix B: BIOS POST Codes

Checkpoint Code Description

60h The DMA page register test passed. Performing the DMA Controller

1 base register test next.
62h The DMA controller 1 base register test passed. Performing the DMA

controller 2 base register test next.
65h The DMA controller 2 base register test passed. Programming DMA

controllers 1 and 2 next.
66h Completed programming DMA controllers 1 and 2. Initializing the 8259

interrupt controller next.
67h Completed 8259 interrupt controller initialization.
7Fh Extended NMI source enabling is in progress.
80h The keyboard test has started. Clearing the output buffer and

checking for stuck keys. Issuing the keyboard reset command next.
81h A keyboard reset error or stuck key was found. Issuing the keyboard

controller interface test command next.
82h The keyboard controller interface test completed. Writing the com-

mand byte and initializing the circular buffer next.
83h The command byte was written and global data initialization has

completed. Checking for a locked key next.
84h Locked key checking is over. Checking for a memory size mismatch

with CMOS RAM data next.
85h The memory size check is done. Displaying a soft error and checking

for a password or bypassing WINBIOS Setup next.
86h The password was checked. Performing any required programming

before WINBIOS Setup next.
87h The programming before WINBIOS Setup has completed.

Uncompressing the WINBIOS Setup code and executing the

AMIBIOS Setup or WINBIOS Setup utility next.

88h Returned from WINBIOS Setup and cleared the screen. Performing

any necessary programming after WINBIOS Setup next.
89h The programming after WINBIOS Setup has completed. Displaying the

power on screen message next.

8Bh The first screen message has been displayed. The <WAIT...>

message is displayed. Performing the PS/2 mouse check and

extended BIOS data area allocation check next.
8Ch Programming the WINBIOS Setup options next.
8Dh The WINBIOS Setup options are programmed. Resetting the hard disk

controller next.
8Fh The hard disk controller has been reset. Configuring the floppy drive

controller next.

91h The floppy drive controller has been configured. Configuring the hard

disk drive controller next.

B-5

SUPERSERVER 6113L-8/6113L-i User's Manual

Checkpoint Code Description

95h Initializing the bus option ROMs from C800 next. See the last page of

this chapter for additional information.

96h Initializing before passing control to the adaptor ROM at C800.

97h Initialization before the C800 adaptor ROM gains control has com-

pleted. The adaptor ROM check is next.

98h The adaptor ROM had control and has now returned control to BIOS

POST. Performing any required processing after the option ROM
returned control.

99h Any initialization required after the option ROM test has completed.

Configuring the timer data area and printer base address next.

9Ah Set the timer and printer base addresses. Setting the RS-232 base

address next.

9Bh Returned after setting the RS-232 base address. Performing any

required initialization before the Coprocessor test next.

9Ch Required initialization before the Coprocessor test is over. Initializing

the Coprocessor next.

9Dh Coprocessor initialized. Performing any required initialization after

the Coprocessor test next.

9Eh Initialization after the Coprocessor test is complete. Checking the

extended keyboard, keyboard ID, and Num Lock key next. Issuing the
keyboard ID command next.

A2 h Displaying any soft errors next.

A3h The soft error display has completed. Setting the keyboard typematic

rate next.

A8h Initialization before passing control to the adaptor ROM at E000h

completed. Passing control to the adaptor ROM at E000h next.

A9h Returned from adaptor ROM at E000h control. Performing any

initialization required after the E000 option ROM had control next.

Aah Initialization after E000 option ROM control has completed. Displaying

the system configuration next.
B0h The system configuration is displayed.
B1h Copying any code to specific areas.

00h Code copying to specific areas is done. Passing control to EFI.

B-6

Appendix C: Software Installation

Appendix C

Software Installation

After all the hardware has been installed, you will need to install the operating
system and other software drivers. The necessary drivers are all included on the
Supermicro CDs that came packaged with your system.

C-1 Introduction to the EFI Platform

The EFI (Extensible Firmware Interface) Platform is a new firmware architecture that
provides an interface between the operating system and the computer firmware
(BIOS). It abstracts system data specified in the system BIOS and translates it into
an object-oriented language that can be easily accessed by the OS. It also provides
a rich environment for system pre-installation. EFI initializes chipset, buses and
drivers and locates OS loaders. Once the EFI Firmware boots up the system, it
hands over the system operation to the OS. When running in the background in the
OS environment, EFI continues to provide the system with simple runtime services
such as monitoring firmware settings and system reset. Due to the interoperability
between the OS and the system BIOS, EFI optimizes the performance of 64-bit
Itanium2 systems.

OS

Primitives

EFI

Data

System

protocols

BIOS

Devices

Hardware

C-1

OS Loader

Abstracts

Drivers

SUPER 6113L-8/6113L-i User's Manual

C-2 AMIBIOS Flash

1. Obtain a USB Pen or a USB storage device (a USB 2.0 device is recommended).

2. From our web site (www.supermicro.com), download the following two files into the
USB pen or device: [amiflash.efi], and [bios.rom].

3. Connect the USB device to one of the USB ports (see Chapter 5 for USB port
locations).

4. Bootup the system with the USB pen connected to a USB port. The system will
boot to the “EFI Boot Manager”. Highlight the “EFI Shell [Built-in]” field and press
<Enter> to select it.

Boot to EFI Boot Manager

5. Once "EFI shell (Built-in)" is selected, you enter the "EFI Shell". In the “EFI
Shell,” locate the USB device (for example fs0 or fs1).

C-2

Appendix C: Software Installation

Location of the USB device
(example)

6. At the shell command prompt, type: Shell> fsX: (where X is the number of the
sector in which your USB pen or device is located). This command will change the

directory from [Shell] to [fsX].

7. Now, start flashing BIOS by typing: fsX:\> amiflash bios.rom (where X is the sector
number in which your USB pen or device is located).

8. At the “Reset NVRAM to default value? (y/n),” prompt, please choose accordingly.

Locate of the USB device
(example)

C-3

SUPER 6113L-8/6113L-i User's Manual

9. When the fsx directory appears, type in the file name at the prompt: fsx:\ amiflash
ami64.rom (eg. in the example shown above, at the prompt type fs0:\> amiflash
ami64.rom and press <Enter> as shown below).

The system will now start loading the BIOS image file.

C-4

Appendix C: Software Installation

After the BIOS Image file is loaded, the following screen will appear:

10. When "Reset NVRAM to default value? (y/n)" is displayed, type "y" at the prompt
if you want to reset all default values after flashing the BIOS. (Yes: this will reset
your NVRAM, which typically resets your boot options in EFI to the manufacturer
defaults. If you previously added options to boot from a CD-ROM or Windows, these
will disappear after NVRAM is reset, and in this case you will have to re-add the
options. No: this will leave NVRAM alone, thus your boot options will remain the
same as before BIOS was flashed.) Type "n" at the prompt if you want to keep the
default values after BIOS flashing as shown in the screen above.

11. When "Proceed with flash update? (y/n)" is displayed, type "y" at the prompt to
update the BIOS. Type "n" at the prompt if you do not wish to update the BIOS. If
you type "y", the system will automatically update the BIOS file.

12. After BIOS is updated, you will be prompted with "Reset CMOS to default values
(will be done during the next boot?) y/n?. Choose "y" if you want to reset BIOS to
the manufacturer’s default settings during the next boot, or "n" if you only want to
update BIOS without resetting it to the manufacturer’s default settings. Please note
that this reset will not affect EFI boot options.

13. You will then be prompted with "Reset the system? y/n?". Type "y" at the prompt
if you want to automatically reboot the system.

C-5

SUPER 6113L-8/6113L-i User's Manual

C-3 Adding the CD-ROM Boot Option in EFI

1. Power on the system and enter the “EFI Boot Manager”.

2. Select “Boot Option Maintenance Menu."

3. Select “Add a Boot Option.”

4. Select “Removable Media Boot [Acpi(PNP0A03,0)/Pci(1F|1)/
ATA(Secondary,Master)]”.
(Note: if your CD-ROM drive is connected to the primary IDE connector,
you must choose it accordingly.)

5. Enter a new description, such as “CD-ROM”.

6. When prompted with “Enter Boot Option Data", type [A-Ascii U-Unicode
N-No boot Option]”. Then, press <Enter>.

7. When prompted with “Enter Boot Option Data", type [Data will be stored
as Unicode string:]” Then, press <Enter>.

8. When prompted with “Save changes to NVRAM [Y-Yes N-No]”,
press Y

9. Select the "Exit" option to exit the "Add Boot Option Menu".

10. Select the "Exit" option to exit the "Boot Maintenance Menu"

11. Once back in the EFI Boot Manager, you now can select the CD-ROM
boot option to boot from the OS installation CD.

C-6