Supermicro SUPER X5DPL-8GM, SUPER X5DPL-iGM User Manual

®

SUPER X5DPL-8GM
SUPER X5DPL-iGM

USER’S MANUAL

Revision 1.1

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please Note: For the most up-to-date version of this manual, please
see our web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2003 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use
of the SUPER X5DPL-8GM/X5DPL-iGM mainboard. The SUPER X5DPL-8GM/
X5DPL-iGM supports single or dual Intel® 604/603-pin XeonTM 512K L2
cache processors at a 533/400 MHz front side bus. Please refer to the
support section of our web site (http://www.supermicro.com/
TechSupport.htm) for a complete listing of supported processors. This
product is intended to be professionally installed.

Manual Organization

Chapter 1 begins with a checklist of what should be included in your

mainboard box, describes the features, specifications and performance of
the motherboard and provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices.
Read this chapter when you want to install the processor and memory
modules and when mounting the mainboard in the chassis. Also refer to
this chapter to connect the floppy and hard disk drives, SCSI drives, the IDE
interfaces, the parallel and serial ports, the keyboard and mouse, the power
supply and various other connections, buttons and indicators.

If you encounter any problems, see Chapter 3, which describes trouble­shooting procedures for the video, the memory and the setup configuration
stored in CMOS. For quick reference, a general FAQ [Frequently Asked
Questions] section is provided. Instructions are also included for contact­ing technical support. In addition, you can visit our web site (at
www.supermicro.com/techsupport.htm) for more detailed information.

Chapter 4 includes an introduction to PhoenixBIOS and provides detailed
information on running the CMOS Setup utility.

Appendix A gives information on BIOS POST messages.

Appendix B provides BIOS POST codes.

iv

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

Preface

About This Manual ...................................................................................................... ii i

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist .................................................................................................... 1-1

Contacting Supermicro ............................................................................ 1-2

Super X5DPL-8GM/X5DPL-iGM Image................................................... 1-4

Super X5DPL-8GM/X5DPL-iGM Layout................................................. 1-5

Super X5DPL-8GM/X5DPL-iGM Quick Reference ............................... 1-6

Motherboard Features ............................................................................. 1-7

Intel E7501 Chipset: System Block Diagram ........................................ 1-9

1-2 Chipset Overview......................................................................................... 1-10

1-3 Special Features........................................................................................... 1-10

ATI Graphics Controller ........................................................................ 1-10

BIOS Recovery ....................................................................................... 1-10

Recovery from AC Power Loss ......................................................... 1-11

1-4 PC Health Monitoring.................................................................................... 1-11

1- 5 ACPI Features ............................................................................................... 1-12

1-6 Power Supply ............................................................................................... 1-14

1- 7 Super I/O......................................................................................................... 1-15

Chapter 2: Installation

2-1 Static-Sensitive Devices ............................................................................... 2-1

Precautions............................................................................................... 2-1

Unpacking.................................................................................................. 2-1

2-2 PGA Processor and Heatsink Installation .................................................. 2-2

2-3 Installing DIMMs............................................................................................... 2-5

2- 4 I/O Ports/Control Panel Connectors ............................................................. 2-6

2-5 Connecting Cables .......................................................................................... 2-8

ATX Power Connector............................................................................ 2-8

Processor Power Connector................................................................. 2-8

NMI Button .................................................................................................. 2-8

Power LED ................................................................................................. 2-8

HDD LED .................................................................................................... 2-9

NIC1 LED ................................................................................................... 2-9

NIC2 LED ................................................................................................... 2-9

Table of Contents

Table of Contents

v

Overheat LED ........................................................................................... 2-9

Power Fail Button ..................................................................................... 2-9

Reset Button ........................................................................................... 2-10

Power Button ......................................................................................... 2-10

Chassis Intrusion ................................................................................... 2-10

Universal Serial Bus (USB0/1) ............................................................ 2-10

Extra Universal Serial Bus Headers ................................................... 2-11

Serial Ports ............................................................................................. 2-11

LAN (Ethernet) Ports.............................................................................. 2-11

ATX PS/2 Keyboard and Mouse Ports ................................................2-11

Fan Headers ........................................................................................... 2-12

Power LED/Speaker (JD1) ................................................................... 2-12

Power Supply Fail Header .................................................................... 2-12

Keylock ..................................................................................................... 2-13

Wake-On-LAN ......................................................................................... 2-13

Wake-On-Ring ......................................................................................... 2-13

2- 6 Jumper Settings ............................................................................................ 2-14

Explanation of Jumpers ........................................................................ 2-14

CMOS Clear............................................................................................. 2-14

Mb LAN Enable/Disable......................................................................... 2-14

Gb LAN Enable/Disable......................................................................... 2-15

VGA Enable/Disable ............................................................................... 2-15

Power Supply Alarm Enable/Disable ................................................... 2-15

SCSI Enable/Disable................................................................................ 2-15

SCSI Termination Enable/Disable..........................................................2-16

Watch Dog Enable/Disable .................................................................... 2-16

Force Power On .....................................................................................2-16

2-7 Onboard Indicators ...................................................................................... 2-17

Gb/Mb LAN LEDs .................................................................................... 2-17

2- 8 Parallel Port, Floppy/Hard Disk Drive and SCSI Connections ............... 2-17

Parallel Port Connector ......................................................................... 2-17

Floppy Connector ................................................................................... 2-18

IDE Connectors ...................................................................................... 2-18

Ultra320 SCSI Connectors ..................................................................... 2-19

2-8 Installing Software Drivers......................................................................... 2-20

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

vi

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................ 3-1

Before Power On .................................................................................... 3-1

No Power .................................................................................................. 3-1

No Video ................................................................................................... 3-1

Memory Errors .......................................................................................... 3-2

Losing the System’s Setup Configuration ........................................... 3-2

3-2 Technical Support Procedures .................................................................... 3-2

3-3 Frequently Asked Questions........................................................................ 3-3

3-4 Returning Merchandise for Service............................................................ 3-5

Chapter 4: BIOS

4- 1 Introduction....................................................................................................... 4-1

4- 2 Running Setup .................................................................................................. 4-2

4- 3 Main Setup........................................................................................................ 4-2

4-4 Advanced Setup.............................................................................................. 4-6

4-5 Security Setup...............................................................................................4-15

4-6 Power Setup ..................................................................................................4-17

4- 7 Boot Setup...................................................................................................... 4-18

4-8 PIR Setup ........................................................................................................4-20

4-9 Exit ................................................................................................................... 4-22

Appendices:

Appendix A: BIOS POST Messages ..................................................................... A-1

Appendix B: BIOS POST Codes .............................................................................B-1

Chapter 1: Introduction

1-1

Introduction

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac­knowledged leader in the industry. Supermicro boards are designed with
the utmost attention to detail to provide you with the highest standards in
quality and performance.

Please check that the following items have been included with your mother­board. If anything listed here is damaged or missing, contact your retailer.

One (1) Supermicro Mainboard

One (1) ribbon cable for IDE devices

One (1) floppy ribbon cable

One (1) USB ribbon cable (retail only)

One (1)COM Port w/Cable (retail only)

One (1) I/O backpanel shield

One (1) Supermicro CD containing drivers and utilities

One (1) User's/BIOS Manual

Two (2) Pentium 4 Xeon active heatsinks (FAN-042-CF, retail only)

Two (2) heatsink retention clips (SKT-095-604E)

SCSI Accessories (X5DPL-8GM only)

One (1) 68-pin LVD SCSI cable (retail only)

One (1) SCSI manual

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-2

Introduction

Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

Chapter 1: Introduction

1-3

Introduction

Notes

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-4

Introduction

Figure 1-1. SUPER X5DPL-8GM/X5DPL-iGM

Chapter 1: Introduction

1-5

Introduction

Figure 1-2. SUPER X5DPL-8GM/X5DPL-iGM Layout*

(not drawn to scale)

The IPMI socket is an optional feature.
Jumpers not noted are for test purposes only.

BANK 3

BANK 2

BANK 1

DIMM #3B

DIMM #3A

DIMM #2B

DIMM #2A

DIMM #1B

ATX PWR CONN

DIMM #1A

Parallel Port

VGA

COM1

USB0/1

Keyboard
Mouse

Mb
LAN

MCH

Rage
XL

J29

Chassis Fan3

CPU 2

CPU 1

ICH3

AIC-7902

Battery

Speaker

COM2

33 MHz PCI #2

33 MHz PCI #1

33 MHz PCI #3

133 MHz PCI-X #6

100 MHz PCI-X #5

100 MHz PCI-X #4

PWRLED/SPKR

BIOS

WOL

J35

JBT1

JD1

FPUSB0/1

USB2

Ultra III LVD SCSI CHB

Chassis Fan4

JL1

JP32

JWOR1

J27

JP4

IPMI

Ultra III LVD SCSI CH A

IDE #2

IDE #1

FLOPPY

SMB

JA1

JP37

J15

Chassis Fan5

CPU2 Chassis Fan

S

UPER X5DPL-8GM

®

JP8

JF2

JP36

JP9

CPU1 Chassis Fan

Gb
LAN

JD3

JP3

JOH1

JP39

JPA2

JP22

JPA1

J9

*Note:
The X5DPL-iGM has the same layout as the X5DPL-8GM but with no SCSI.

CPU/Ch Fan

JP40

Gb LAN
Controller

Mb LAN
Controller

J26

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-6

Introduction

X5DPL-8GM/X5DPL-iGM Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear See Section 2-6
JP3/JD3 Mb/Gb LAN Enable/Disable Pins 1-2 (Enabled)
JP4 VGA Enable/Disable Pins 1-2 (Enabled)
JP22* SCSI Enable/Disable Pins 1-2 (Enabled)
JP37 Watch Dog Open (Disabled)
JP39 CPU Clock Pins 1-2 (Auto)
JP40 Force Power On Open (Disabled)
JPA1/JPA2* SCSI CH A/B Termination Open (Enabled)

Connector Description

ATX PWR CONN Primary ATX Power Connector
DIMM#1A-DIMM#3B Memory (RAM) Slots
COM1/COM2 COM1/COM2 Serial Port Connector
CPU/Chassis FAN CPU/Chassis Fan Headers
Gb LAN Gigabit LAN (Ethernet) Port
IDE#1/IDE#2 IDE #1/#2 Hard Disk Drive Connectors
FPUSB0/1 Front Side USB0/1 Headers
J9 PS/2 Keyboard/Mouse Ports
J15** Processor Power Connector
J29 Parallel (Printer) Port
JA1* Ultra320 LVD SCSI CH A Connector
JA2* Ultra320 LVD SCSI CH B Connector
JD1 PWR LED Header / Speaker Header/Jumper
JF2 Front Control Panel Connector
JL1 Chassis Intrusion Header
JOH1 Overheat LED
JP7 Floppy Disk Drive Connector
JP8 Power Fault
JP9 Third Power Supply Fail Header (Enable)
JP35 Keylock Switch Connector
JP36 3rd Power Supply Alarm Reset Switch
JWOR1 Wake-on-Ring Header
Mb LAN Mb LAN (Ethernet) Port
Speaker Onboard Speaker Header
USB2 USB2 Header
VGA VGA Display (Monitor) Port
WOL Wake-on-LAN Header

* X5DPL-8GM only
**

The 12v 8-pin processor power connector at J15 must also be

connected to your power supply.

Chapter 1: Introduction

1-7

Introduction

Motherboard Features

CPU

• Single or dual Intel® 604/603-pin XeonTM 512K L2 cache processors at
a 533/400 MHz front side (system) bus speed.

Note: Please refer to the support section of our web site for a complete listing of supported
processors (http://www.supermicro.com/TechSupport.htm).

Memory

• Six 184-pin DDR DIMM sockets supporting up to 12 GB of registered
ECC DDR-266/200 (PC2100/1600) SDRAM

Note: Interleaved memory; requires memory modules to be installed in pairs. DDR-266
(PC2100) memory is supported only when run with 533 MHZ FSB processors. See Section 2-3
for details.

Chipset

• Intel E7501 (Plumas) chipset

Expansion Slots

• Three 64-bit, 100 MHz PCI-X

• Three 32-bit, 33 MHz PCI

BIOS

• 4 Mb Phoenix® Flash ROM

• APM 1.2, DMI 2.1, PCI 2.2, ACPI 1.0, Plug and Play (PnP), SMBIOS 2.3

PC Health Monitoring

• Onboard voltage monitors for CPU cores, chipset voltage, 3.3V, +5V,
+12V and 3.3V standby

• Fan status monitor with firmware/software on/off control

• CPU/chassis temperature monitors

• Environmental temperature monitor and control

• CPU fan auto-off in sleep mode

• CPU slow-down on temperature overheat

• CPU overheat LED header

• Power-up mode control for recovery from AC power loss

• Auto-switching voltage regulator for CPU core

• Chassis intrusion detection

• System resource alert

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-8

Introduction

ACPI/PC 98 Features (optional)

• Microsoft OnNow

• Slow blinking LED for suspend state indicator

• Main switch override mechanism

• External modem ring-on

Onboard I/O

• AIC-7902 for dual channel Ultra320 SCSI (X5DPL-8GM only)

• Adaptec SCSI RAID 2010S supported (X5DPL-8GM only)

• Integrated ATI Rage XL graphics controller

• One Intel 82551 10/100 Mb fast Ethernet and one Intel 82545EM Gb
Ethernet port

• 2 EIDE Ultra DMA/100 bus master interfaces

• 1 floppy port interface (up to 2.88 MB)

• 2 Fast UART 16550A compatible serial ports

• 1 EPP/ECP Parallel Port (Enhanced Parallel Port/Extended Capabilities
Port)

• PS/2 mouse and PS/2 keyboard ports

• Two USB (Universal Serial Bus) ports, three USB headers (USB 1.1)

• Eight SATA (Serial ATA) connectors (*X5DPL-TGM only)

Other

• Internal/external modem ring-on

• Recovery from AC power loss control

• Wake-on-LAN (WOL)

• Console redirection

• IPMI (optional)

CD/Diskette Utilities

• BIOS flash upgrade utility

• Device drivers

Dimensions

• Extended ATX, 12" x 13.05" (304.8 x 331.5 mm)

Chapter 1: Introduction

1-9

Introduction

Notes:

This is a general block diagram. Please see the previous Motherboard
Features pages for details on the features of each motherboard.

X5DPL-8GM
a. All PCI slots are connected to ICH3.

b. PCI-X Slot5 and SCSI share a 66 MHz bus on the P64H2 controller.
c. PCI-X Slot6 shares a 100 MHz bus on the P64H2 with the Gbit LAN.

X5DPL-iGM
a. All PCI slots are connected to ICH3.
b. PCI-X Slot4 and PCI-X Slot5 run on a 100 MHz bus from the P64H2.
c. PCI-X Slot6 shares a 100 MHz bus on the P64H2 with the Gbit LAN.

MCH

533/400 MHz Host Bus

266/200 MHz
Memo ry B u s

P64H2

Processor Processor

DDR266/200

ICH3

66 MHz

PCI Bus

PCI-X Slot

#5

PCI-X

Slot #4

SCSI

PCI-X Slot #6

Gbit LAN

100 MHz

PCI-X Bus

ID E

Audio

CODEC

USB Ports

LPC I/O BIOS FWH

PCI Slot #1

UDMA/100

USB 1.1

AC97

PCI Slot #3

PCI Slot #2

VGA

Mb it LA N

33 MHz PCI Bu s

LPC Bus

Figure 1-3. Intel E7501 Chipset:

System Block Diagram

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-10

Introduction

1-2 Chipset Overview

The Intel E7501 (Plumas) chipset is a high-performance chipset with a per­formance and feature-set designed for mid-range, dual processor servers.
The E7501 chipset consists of four major components: the Memory Control­ler Hub (MCH), the I/O Controller Hub 3 (ICH3), the PCI-X 64-bit Hub 2.0
(P64H2) and the 82808AA Host Channel Adapter (VxB).

The MCH has four hub interfaces, one to communicate with the ICH3 and
three for high-speed I/O communications. The MCH employs a 144-bit wide
memory bus for a DDR-200 memory interface, which provides a total band­width of 3.2 GB/s. The ICH3 interface is a 266 MB/sec point-to-point con­nection using an 8-bit wide, 66 MHz base clock at a 4x data transfer rate.
The P64H2 interface is a 1 GB/s point-to-point connection using a 16-bit
wide, 66 MHz base clock at a 8x data transfer rate.

The ICH3 I/O Controller Hub provides various integrated functions, including
a two-channel UDMA100 bus master IDE controller, USB host controllers, an
integrated LAN controller, a System Management Bus controller and an
AC'97 compliant interface.

The P64H2 PCI-X Hub provides a 16-bit connection to the MCH for high­performance I/O capability and two 64-bit PCI-X interfaces.

1-3 Special Features

ATI Graphics Controller

The X5DPL-8GM/X5DPL-iGM has an integrated ATI video controller based on
the Rage XL graphics chip. The Rage XL fully supports sideband address­ing and AGP texturing. This onboard graphics package can provide a band­width of up to 512 MB/sec over a 32-bit graphics memory bus.

BIOS Recovery

The BIOS Recovery function allows you to recover your BIOS image file if
the BIOS flashing procedure fails (see Section 3-3).

Chapter 1: Introduction

1-11

Introduction

Recovery from AC Power Loss

BIOS provides a setting for you to determine how the system will respond
when AC power is lost and then restored to the system. You can choose
for the system to remain powered off (in which case you must hit the
power switch to turn it back on) or for it to automatically return to a power­on state. See the Power Lost Control setting in the Advanced BIOS Setup
section (Peripheral Device Configuration) to change this setting. The de­fault setting is Always On.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the SUPER
X5DPL-8GM/X5DPL-iGM. The motherboard has an onboard System Hard­ware Monitor chip that supports PC health monitoring.

Onboard Voltage Monitors for the CPU Cores, Chipset
Voltage, +3.3V, +5V, +12V and +3.3V Standby

An onboard voltage monitor will scan these voltages continuously. Once a
voltage becomes unstable, a warning is given or an error message is sent
to the screen. Users can adjust the voltage thresholds to define the
sensitivity of the voltage monitor.

Fan Status Monitor with Firmware/Software On/Off Control

The PC health monitor can check the RPM status of the cooling fans. The
onboard 3-pin CPU and chassis fans are controlled by the power manage­ment functions. The thermal fan is controlled by the overheat detection
logic.

Environmental Temperature Control

The thermal control sensor monitors the CPU temperature in real time and
will turn on the thermal control fan whenever the CPU temperature exceeds
a threshold. The overheat circuitry runs independently from the CPU. It can
continue to monitor for overheat conditions even when the CPU is in sleep
mode. Once it detects that the CPU temperature is too high, it will automati­cally turn on the thermal control fan to prevent any overheat damage to the
CPU. The onboard chassis thermal circuitry can monitor the overall system
temperature and alert users when the chassis temperature is too high.

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-12

Introduction

CPU Fan Auto-Off in Sleep Mode

The CPU fan activates when the power is turned on. It continues to operate
when the system enters Standby mode. When in sleep mode, the CPU will
not run at full power, thereby generating less heat.

CPU Overheat LED

JOH1 is a header used to connect to a CPU overheat LED. When the CPU
temperature becomes too high, both the overheat fan and the warning LED
are activated.

System Resource Alert

This feature is available when used with Intel's LANDesk Client Manager
(optional). LDCM is used to notify the user of certain system events. For
example, if the system is running low on virtual memory and there is insuf­ficient hard drive space for saving the data, you can be alerted of the
potential problem.

Auto-Switching Voltage Regulator for the CPU Core

The auto-switching voltage regulator for the CPU core can support up to
20A current and auto-sense voltage IDs ranging from 1.4V to 3.5V. This
will allow the regulator to run cooler and thus make the system more stable.

1-5 ACPI Features

ACPI stands for Advanced Configuration and Power Interface. The ACPI
specification defines a flexible and abstract hardware interface that pro­vides a standard way to integrate power management features throughout
a PC system, including its hardware, operating system and application soft­ware. This enables the system to automatically turn on and off peripherals
such as CD-ROMs, network cards, hard disk drives and printers. This also
includes consumer devices connected to the PC such as VCRs, TVs, tele­phones and stereos.

Chapter 1: Introduction

1-13

Introduction

In addition to enabling operating system-directed power management, ACPI
provides a generic system event mechanism for Plug and Play and an oper­ating system-independent interface for configuration control. ACPI lever­ages the Plug and Play BIOS data structures while providing a processor
architecture-independent implementation that is compatible with both Win­dows 2000 and Windows NT 5.0.

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to
system and device power control. OnNow is a term for a PC that is always
on but appears to be off and responds immediately to user or other re­quests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start
blinking to indicate that the CPU is in suspend mode. When the user presses
any key, the CPU will wake-up and the LED will automatically stop blinking
and remain on.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a
system suspend button to make the system enter a SoftOff state. The
monitor will be suspended and the hard drive will spin down. Depressing
the power button again will cause the whole system to wake-up. During
the SoftOff state, the ATX power supply provides power to keep the re­quired circuitry in the system alive. In case the system malfunctions and
you want to turn off the power, just depress and hold the power button for
4 seconds. This option can be set in the Power section of the BIOS Setup
routine.

External Modem Ring-On

Wake-up events can be triggered by a device such as the external modem
ringing when the system is in the SoftOff state. Note that external modem
ring-on can only be used with an ATX 2.01 (or above) compliant power
supply.

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-14

Introduction

Wake-On-LAN (WOL)

Wake-On-LAN is defined as the ability of a management application to re­motely power up a computer that is powered off. Remote PC setup, up­dates and asset tracking can occur after hours and on weekends so that
daily LAN traffic is kept to a minimum and users are not interrupted. The
motherboards have a 3-pin header (WOL) to connect to the 3-pin header on
a Network Interface Card (NIC) that has WOL capability. Wake-On-LAN
must be enabled in BIOS. Note that Wake-On-Lan can only be used with an
ATX 2.01 (or above) compliant power supply.

1-6 Power Supply

As with all computer products, a stable power source is necessary for
proper and reliable operation. It is even more important for processors that
have high CPU clock rates.

The SUPER X5DPL-8GM/X5DPL-iGM accommodates ATX power supplies.
Although most power supplies generally meet the specifications required by
the CPU, some are inadequate. You should use one that will supply at least
400W of power and includes the additional +12V, 8-pin power connector ­an even higher wattage power supply is recommended for high-load con­figurations. Also your power supply must provide 1.5A, which is needed
for the LAN port(s).

NOTE: The processor 12v power connector (J15) is necessary to
support Intel Xeon CPUs. Failure to provide this extra power will
result in the CPUs becoming unstable after only a few minutes of
operation. See Section 2-5 for details on connecting the power
supply cables.

It is strongly recommended that you use a high quality power supply that
meets ATX power supply Specification 2.02 or above. It must also be SSI
compliant (info at http://www.ssiforum.org/). Additionally, in areas where
noisy power transmission is present, you may choose to install a line filter
to shield the computer from noise. It is recommended that you also install a
power surge protector to help avoid problems caused by power surges.

Chapter 1: Introduction

1-15

Introduction

1-7 Super I/O

The disk drive adapter functions of the Super I/O chip include a floppy disk
drive controller that is compatible with industry standard 82077/765, a data
separator, write pre-compensation circuitry, decode logic, data rate selec­tion, a clock generator, drive interface control logic and interrupt and DMA
logic. The wide range of functions integrated onto the Super I/O greatly
reduces the number of components required for interfacing with floppy disk
drives. The Super I/O supports 360 K, 720 K, 1.2 M, 1.44 M or 2.88 M disk
drives and data transfer rates of 250 Kb/s, 500 Kb/s or 1 Mb/s.It also
provides two high-speed, 16550 compatible serial communication ports
(UARTs), one of which supports serial infrared communication. Each UART
includes a 16-byte send/receive FIFO, a programmable baud rate generator,
complete modem control capability and a processor interrupt system.
Each UART includes a 16-byte send/receive FIFO, a programmable baud
rate generator, complete modem control capability and a processor inter­rupt system. Both UARTs provide legacy speed with baud rate of up to

115.2 Kbps as well as an advanced speed with baud rates of 250 K, 500 K,
or 1 Mb/s, which support higher speed modems.

The Super I/O supports one PC-compatible printer port (SPP), Bi-directional
Printer Port (BPP) , Enhanced Parallel Port (EPP) or Extended Capabilities
Port (ECP).

The Super I/O provides functions that comply with ACPI (Advanced Con­figuration and Power Interface), which includes support of legacy and ACPI
power management through an SMI or SCI function pin. It also features
auto power management to reduce power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can flexibly
adjust to meet ISA PnP requirements, which support ACPI and APM (Ad­vanced Power Management).

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

1-16

Introduction

Notes

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Static-Sensitive Devices

Electric-Static-Discharge (ESD) can damage electronic components. To pre­vent damage to your system board, it is important to handle it very carefully.
The following measures are generally sufficient to protect your equipment
from ESD.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the anti­static bag.

• Handle the board by its edges only; do not touch its components, periph­eral chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when
not in use.

• For grounding purposes, make sure your computer chassis provides ex­cellent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage.
When unpacking the board, make sure the person handling it is static protected.

2-2

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

IMPORTANT: Always connect the power cord last and always remove it
before adding, removing or changing any hardware components. Make
sure that you install the processor into the CPU socket before you install
the CPU heat sink.

2-2 PGA Processor and Heatsink Installation

1. Locate the following components, which are included in the shipping
package. The amounts shown are for each CPU.

Retention brackets

(2)

Clips (2)

Screws* (4)

*These screws are for mounting the
motherboard to the back panel of a
chassis that has four mounting holes
(as shown on right).

White pegs (4)

2. Insert the white pegs into the
black anchors. Do not force the
white pegs all the way in - only
about 1/3 of the way into the black
anchors.

3. Place a retention bracket in the
proper position and secure it by
pressing pegs into two of the retention
holes until you hear a *click*. The
clicking sound indicates that the peg is
locked and secured.

Two pegs in
position

One retention bracket in
position

Black anchors (4)

For chassis that do not have four
mounting holes, use the anchor/peg
assemblies:

Anchor/peg
assemblies

When handling the processor package, avoid placing direct
pressure on the label area of the fan. Also, do not place the
motherboard on a conductive surface, which can damage the
BIOS battery and prevent the system from booting up.

!

Chapter 2: Installation

2-3

5. Lift the lever on the CPU socket:

lift the lever completely or you will
damage the CPU socket when
power is applied. (Install CPU1
first.)

Socket lever

6. Install the CPU in the socket. Make sure

that pin 1 of the CPU is seated on pin 1 of
the socket (both corners are marked with a
triangle). When using only one CPU, install it
into CPU socket #1 (CPU socket #2 is auto­matically disabled if only one CPU is used).

Pin 1

7. Press the lever down until

you hear it *click* into the
locked position.

Socket lever in
locked position

4. Secure the other retention

bracket into position by
repeating Step 3.

8. Apply the proper amount of thermal

glue to the CPU die and place the
heatsink and fan on top of the CPU.

Heatsink

9. Secure the heatsink by locking the

retention clips into their proper
position.

10. Connect the three wires of

the CPU fan to the respective CPU
fan connector.

CPU fan
connector

CPU fan
wires

Retention clip

CPU

2-4

SUPER X5DPL-8GM/X5DPL-iGM User’s Manual

Figure 2-1. PGA604 Socket: Empty and with Processor Installed

Mounting the Motherboard in the Chassis

All motherboards have standard mounting holes to fit different types of
chassis. Make sure the location of all the mounting holes for both the
motherboard and the chassis match. Although a chassis may have both
plastic and metal mounting fasteners, metal ones are highly recommended
because they ground the motherboard to the chassis. Make sure the metal
standoffs click in or are screwed in tightly. Then use a screwdriver to
secure the motherboard onto the motherboard tray.

Warning! Make

sure you lift the
lever completely
when installing the
CPU. If the lever is
only partly raised,
damage to the
socket or CPU may
result.

Pin 1

Lever

Processor

(installed)

!