Supermicro Supero H8SGL-F, Supero H8SGL User Manual

USER’S MANUAL

Revision 1.2

®

SUPER

H8SGL
H8SGL-F

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at

www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.

IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL
NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall be
the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims
will not exceed the price paid for the hardware product.

FCC Statement: Refer to Supermicro's web site for FCC Compliance Information.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.2
Release Date: December 27, 2012
Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.
Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

iii

Preface

About This Manual

This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
H8SGL(-F) serverboard.

The H8SGL(-F) serverboard is based on the AMD® SR5650/SP5100 chipset and
supports one AMD Socket G34 type processor with up to 256 GB of registered
ECC or 64 GB of unbuffered ECC/non-ECC DDR3-1600/1333/1066 Mhz SDRAM.
The H8SGL serverboard does not have IPMI capability, whereas the H8SGL-F
serverboard does.

Please refer to the motherboard specifi cations pages on our web site for updates on
supported processors (http://www.supermicro.com/aplus/). This product is intended
to be professionally installed.

Manual Organization

Chapter 1 includes a checklist of what should be included in your motherboard

box, describes the features, specifi cations and performance of the motherboard
and provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices. Read this
chapter when installing the processor(s) and memory modules and when installing
the motherboard in a chassis. Also refer to this chapter to connect the hard disk
drives, the various ports, and the power and reset buttons and the system LEDs.

If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the setup confi guration stored in CMOS.
For quick reference, a general FAQ (Frequently Asked Questions) section is
provided. Instructions are also included for contacting technical support. In addition,
you can visit our web site for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Code Messages.
Appendix B lists BIOS POST Checkpoint Codes.

iv

H8SGL(-F) SERVERBOARD USER'S MANUAL

Notes

v

Standardized Warning Statements

Standardized Warning Statements

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience diffi culty, Contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.

com/about/policies/safety_information.cfm.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー

カーが推奨する型、または 同等のものを 使用下さい。 使用済電池は製造元の指示に従

って処 分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。

Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

vi

H8SGL(-F) SERVERBOARD USER'S MANUAL

Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

Standardized Warning Statements

vii

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。

警告

本产品的废弃处理应根据所有国家的法律和规章进行。

警告

本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

viii

H8SGL(-F) SERVERBOARD USER'S MANUAL

Notes

ix

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist ..........................................................................................................1-1

1-2 Contacting Supermicro .................................................................................... 1-2

1-3 Motherboard Features ..................................................................................... 1-7

1-4 Chipset Overview ..........................................................................................1-10

AMD SR5650/SP5100 Chipset .....................................................................1-10

HyperTransport Technology .......................................................................... 1-10

1-5 PC Health Monitoring .................................................................................... 1-10

1-6 Power Confi guration Settings.........................................................................1-11

1-7 Power Supply ................................................................................................1-12

1-8 Super I/O ....................................................................................................... 1-13

Chapter 2 Installation

2-1 Static-Sensitive Devices .................................................................................. 2-1

Precautions .....................................................................................................2-1

Unpacking .......................................................................................................2-1

2-2 Processor and Heatsink Installation................................................................2-2

2-3 Mounting the Motherboard into a Chassis ...................................................... 2-4

2-4 Installing Memory ............................................................................................2-4

DIMM Module Population Confi guration .................................................... 2-6

2-5 PCI Expansion Cards ...................................................................................... 2-7

2-6 I/O Port and Control Panel Connections ........................................................ 2-8

Front Control Panel ......................................................................................... 2-8

2-7 Connector Defi nitions ..................................................................................... 2-9

Power Connectors ..................................................................................... 2-9

PW_ON Connector ..................................................................................... 2-9

Reset Connector ........................................................................................ 2-9

Overheat/Fan Fail LED (OH)......................................................................2-9

NIC2 (LAN2) LED ..................................................................................... 2-10

NIC1 (LAN1) LED ..................................................................................... 2-10

HDD LED .................................................................................................. 2-10

Power On LED ......................................................................................... 2-10

NMI Button ...............................................................................................2-10

LAN1/2 (Ethernet Ports) ........................................................................... 2-10

Universal Serial Bus Ports ........................................................................2-11

USB Headers ............................................................................................2-11

Table of Contents

x

Fan Headers ..............................................................................................2-11

Serial Ports ................................................................................................2-11

SGPIO ......................................................................................................2-12

Chassis Intrusion ..................................................................................... 2-12

Overheat LED ........................................................................................... 2-12

Wake-On-LAN ..........................................................................................2-12

Power I2C ................................................................................................. 2-12

Power LED/Speaker ................................................................................. 2-13

ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................ 2-13

IPMB .........................................................................................................2-13

Video Connector ....................................................................................... 2-13

Compact Flash Card PWR Connector .....................................................2-14

Trusted Platform Module Header ............................................................. 2-14

2-8 Jumper Settings ............................................................................................ 2-15

Explanation of Jumpers ................................................................................ 2-15

CMOS Clear .............................................................................................2-15

I2C to PCI-Express Slot ...........................................................................2-16

VGA Enable/Disable ................................................................................. 2-16

LAN1/2 Enable/Disable ...........................................................................2-16

Onboard Speaker Enable/Disable ............................................................2-16

Compact Flash Master/Slave Select ........................................................ 2-17

Watch Dog Enable/Disable ...................................................................... 2-17

USB Wake-Up ......................................................................................... 2-17

BMC Jumper ............................................................................................ 2-17

2-9 Onboard Indicators ........................................................................................ 2-18

LAN1/LAN2 LEDs ..................................................................................... 2-18

Dedicated IPMI LAN LEDs .......................................................................2-18

Power LED ............................................................................................... 2-18

2-10 IDE and SATA Drive Connections ................................................................. 2-19

IDE Connector .......................................................................................... 2-19

SATA Ports ...............................................................................................2-19

2-11 Enabling SATA RAID .....................................................................................2-20

Serial ATA (SATA).......................................................................................... 2-20

Installing the OS/SATA Driver ....................................................................... 2-20

Building a Driver Diskette ......................................................................... 2-20

Enabling SATA RAID in the BIOS .................................................................2-21

Using the Adaptec RAID Utility ..................................................................... 2-22

Installing the RAID Driver During OS Installation .........................................2-22

2-12 Installing Drivers ............................................................................................2-23

H8SGL(-F) SERVERBOARD USER'S MANUAL

Table of Contents

xi

Supero Doctor III ........................................................................................... 2-24

2-13 Serverboard Battery ...................................................................................... 2-26

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1

No Power ........................................................................................................3-1

No Video .........................................................................................................3-2

Memory Errors ............................................................................................... 3-2

Losing the System’s Setup Confi guration ....................................................... 3-2

3-2 Technical Support Procedures ........................................................................ 3-2

3-3 Frequently Asked Questions ...........................................................................3-3

3-4 Returning Merchandise for Service.................................................................3-4

Chapter 4 BIOS

4-1 Introduction ......................................................................................................4-1

4-2 Main Menu ...................................................................................................... 4-2

4-3 Advanced Settings Menu ................................................................................4-2

4-3 Security Menu ............................................................................................... 4-15

4-4 Boot Menu ..................................................................................................... 4-16

4-5 Exit Menu ...................................................................................................... 4-17

Appendix A BIOS Error Beep Codes
Appendix B BIOS POST Checkpoint Codes

B-1 Uncompressed Initialization Codes ................................................................. B-1

B-2 Bootblock Recovery Codes ............................................................................. B-2

B-3 Uncompressed Initialization Codes ................................................................. B-3

Notes

xii

H8SGL(-F) SERVERBOARD USER'S MANUAL

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.

• One (1) H8SGL(-F) serverboard

• One (1) I/O shield (MCP-260-00027-0N)

• One (1) Retention bracket (BKT-0035L)

• One (1) 9-pin serial port cable (CBL-0010L)

• One (1) ATA 66/100 IDE LP cable (CBL-0036L-03)

• Six (6) 2ft. Amphenol, SATA cable (CBL-0044L)

Note: For your system to work properley, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.

• SMCI product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information:

http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

[e-mail]

1-2

H8SGL(-F) SERVERBOARD USER'S MANUAL

1-2 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

Web Site:

www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho Dist., New Taipei City 235

Taiwan
Tel: [phone]
Fax: [phone]
Web Site:

www.supermicro.com.tw

Technical Support:
Email:

[e-mail]

Tel: [phone]

Chapter 1: Introduction

1-3

Figure 1-1. H8SGL(-F) Image

1-4

H8SGL(-F) SERVERBOARD USER'S MANUAL

Notes:

Jumpers not indicated are for test purposes only.
Not all ports, jumpers or LED Indicators are available on all serverboards.

Figure 1-2. H8SGL(-F) Motherboard Layout

(not drawn to scale)

JPW1

JPI2C1

JF1

JPW2

JWF1

IPMB

SATA5SATA4SATA3SATA2SATA1SATA0

JWOL

JD1

JCF1

JOH1

JI2C1

JI2C2

JL1

DP3

BATTERY

JBT1

JPL1

JPL2

JPUSB1

JPG1

JWD

FAN2

FAN1

FAN6

FAN5

FAN3FAN4

DIMM4B

DIMM4A

DIMM3B

DIMM3A

DIMM2B

DIMM2A

DIMM1B

DIMM1A

T-SGPIO1T-SGPIO2

IDE#1

CPU

USB2

USB3

SLOT6 PCI-E 2.0 x8 (in x16)

SLOT5 PCI-E 2.0 X8

USB6/7USB4/5

SLOT3 PCI 33MHz

SLOT2 PCI 33MHz

SLOT1 PCI 33MHz

LAN2

LAN1

COM2

CMOS CLEAR

COM1

VGA

LAN IPMI/

USB0/1

KB/

Mouse

SLOT4 PCI-E 2.0 x4 (in x8)

AMD

SR5100

AMD

SR5650

Winbond

WPCCM450

BMC

JPB

JLPC1

Chapter 1: Introduction

1-5

H8SGL(-F) Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear (See Section 2-7)
JCF1 Compact Flash Master/Slave Closed (Master)

JD1 Power LED

Pins 1-3: Power LED
Pins 4-7: Speaker

JI2C1/JI2C2 I2C to PCI-E Slot Enable/Disable Both Open (Disabled)
JPB BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN 1 Enable/Disable Pins 1-2 (Enabled)
JPL2 LAN 2 Enable/Disable Pins 1-2 (Enabled)
JPUSB1 USB Power

Pins 1-2: Dual Power
Pins 2-3: Standalone Power

JWD Watch Dog Pins 1-2 (Reset)

LED Description

LAN Ports LEDs for the LAN Ethernet ports
Dedicated IPMI LAN LEDs for the dedicated IPMI LAN Ethernet port (H8SGL-F only)
DP3 LED for Serverboard Power-On

1-6

H8SGL(-F) SERVERBOARD USER'S MANUAL

Connector Description

COM1/COM2 COM1 Serial Port/Header
FAN 1-6 Chassis/CPU Fan Headers
IDE#1 IDE Disk Drive Connector
IPMB System Management Bus Header for the IPMI Slot
IPMI LAN Dedicated IPMI LAN Port (H8SGL-F only)
JD1 Speaker Header
JF1 Front Panel Connector
JL1 Chassis Intrusion Header
JOH1 Overheat Warning Header
JPI2C1 Power I2C Header
JPW1 24-pin Main ATX Power Connector
JPW2 +12V 8-pin CPU Power Connectors
JWF1 Compact Flash Card Power Connector
JWOL Wake-On-LAN Header
JLPC1 TPM Connector
LAN1/2 Gigabit Ethernet (RJ45) Ports
PS2 Mouse/Keyboard PS2 Mouse/Keyboard connectors
SATA0 ~ SATA5 SATA Ports
T-SGPIO1/T-SGPIO2 Serial General Purpose Input/Output Header for SATA
USB0/1, USB4/5, USB2/3, USB6/7 Universal Serial Bus (USB) Ports, Type-A Ports and Headers
VGA VGA Connector

Chapter 1: Introduction

1-7

1-3 Motherboard Features

CPU

• Single AMD Opteron 6000 series processor

Note: Refer to our web site for details on supported processors.

Memory

• Single/Dual/Tri/Quad channel DIMM slots supporting up to 256 GB of registered

ECC or 64 GB of unbuffered ECC/non-ECC DDR3-1600/1333/1066 Mhz speed,
1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size SDRAM

Note: Refer to Section 2-4 before installing memory and our web site for recommended DIMMs.

Chipset

• AMD SR5650 chipset and one SP5100 Southbridge chipset

Expansion Slots

• One (1) PCI-Express x8 (in x16 slot) Gen. 2

• One (1) PCI-Express x8 Gen. 2

• One (1) PCI-Express x4 (in x8 slot) Gen. 2

• Three (3) PCI slots

BIOS

• 16 Mb AMI BIOS® SPI Flash ROM

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS

2.3, Real Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys,
Hardware BIOS Virus Protection

PC Health Monitoring

• Onboard voltage monitors

• Fan status monitor with fi rmware/software on/off and speed control

• Watch Dog

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System resource alert (via included utility program)

• Auto-switching voltage regulator for the CPU core

• CPU thermal trip support

• I

2

C temperature sensing logic

• Chipkill Support

1-8

H8SGL(-F) SERVERBOARD USER'S MANUAL

ACPI Features

• Microsoft OnNow

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Wake-On-LAN (WOL)

Onboard I/O

• Six (6) SATA ports supported by an on-chip SATA controller (RAID 0, 1 and 10

supported)

• Eight (8) USB (Universal Serial Bus 2.0) ports (2x rear, 4x header, 2x type A)

• Two (2) LAN ports supported by two onboard Intel® 82574 dual port Ethernet

controller for 10/100/1000Base-T

• One (1) dedicated IPMI LAN port (H8SGL-F only)

• One (1) VGA port supported by an onboard Matrox

®

G200 graphics controller

(with 16 MB DDR2 memory)

• One (1) UDMA IDE 133/100 connector

• Two COM Ports (one external serial port, one Fast UART 16550 port)

Other

• Onboard power LED

• Chassis intrusion detection

CD Utilities

• BIOS fl ash upgrade utility

• Super Doctor III

• IPMI 1.5 / 2.0

Dimensions

• ATX form: (LxW) 12" x 8" (305 x 203 mm)

Chapter 1: Introduction

1-9

DIMM1B

DIMM1A

CPU1

HT3 Link
16/16-2.6 GHz

DIMM2B

DIMM2A

DIMM3B

DIMM3A

DIMM4B

DIMM4A

PCI SLOT1

PCI-E GEN2 X8

Slot6 PCIE x8/x16

IDE (ATA/133)

SA

TA x6

PCI-E GEN2 X8

Slot5 x8

PCI-E GEN2 x1

INTEL

82574L

RJ45

A-Link

SP5100

BMC
VGA

WPCM450-R

PCI

LPC

SMBus

SIO

W83527HG

HWM

W83795G

SPI Flash

KB/MS

COM2

RMII

DDR2 SDRAM

64MB X16

PSU I2C

IPMB

FE PHY

RTL8201N

VGA

RJ45

Clock Gen

TPM

SR5650

COM1

RJ45

INTEL

82574L

PCI SLOT2

PCI SLOT3

PCI-E GEN2 X4

Slot4

SWITCH

PCI-E GEN2 x1

8xUSB

Figure 1-3. AMD SR5650/SP5100 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the previous pages for the

actual specifi cations of your motherboard.

1-10

H8SGL(-F) SERVERBOARD USER'S MANUAL

1-4 Chipset Overview

The H8SGL(-F) serverboard is based on the AMD SR5650/SP5100 chipset. This
chipset functions as a Media and Communications Processor (MCP). Controllers for
the system memory are integrated directly into AMD Opteron processors.

AMD SR5650/SP5100 Chipset

The AMD SR5650/SP5100 are each a single-chip, high-performance HyperT ransport
peripheral controller. It includes a 22-lane PCI Express interface, an AMD Opteron
16-bit Hyper Transport interface link, a six-port Serial ATA interface and a eight-port
USB 2.0 interface. This hub connects directly to the CPU.

HyperTransport Technology

HyperTransport technology is a high-speed, low latency point to point link that was
designed to increase the communication speed by a factor of up to 48x between
integrated circuits. This is done partly by reducing the number of buses in the
chipset to reduce bottlenecks and by enabling a more effi cient use of memory
in multi-processor systems. The end result is a signifi cant increase in bandwidth
within the chipset.

1-5 PC Health Monitoring

This section describes the PC health monitoring features of the H8SGL(-F)
serverboard. The serverboard has an onboard System Hardware Monitor chip that
supports PC health monitoring.

Onboard Voltage Monitors

The onboard voltage monitor will continuously scan crucial voltage levels. Once
a voltage becomes unstable, it will give a warning or send an error message to
the screen. Users can adjust the voltage thresholds to defi ne the sensitivity of the
voltage monitor. Real time readings of these voltage levels are all displayed in BIOS.

Fan Status Monitor with Firmware/Software Speed Control

The PC health monitor can check the RPM status of the cooling fans. The onboard
fans are controlled by thermal management via BIOS.

Chapter 1: Introduction

1-11

CPU Overheat/Fan Fail LED and Control

This feature is available when the user enables the CPU overheat/Fan Fail warning
function in the BIOS. This allows the user to defi ne an overheat temperature. When
this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail
warning LED is triggered.

Auto-Switching Voltage Regulator for the CPU Core

The 6-phase-switching voltage regulator for the CPU core can support up to
AMD Opteron 6000SE series processors and auto-sense voltage IDs ranging from

0.8 V to 1.55V. This will allow the regulator to run cooler and thus make the system
more stable.

1-6 Power Confi guration Settings

This section describes the features of your motherboard that deal with power and
power settings.

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to system
and device power control. OnNow is a term for a PC that is always on but appears
to be off and responds immediately to user or other requests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If a USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.

1-12

H8SGL(-F) SERVERBOARD USER'S MANUAL

Main Switch Override Mechanism

The power button can function as a system suspend button. When the user
depresses the power button, the system will enter a SoftOff state. The monitor
will be suspended and the hard drive will spin down. Depressing the power button
again will cause the whole system to wake-up. During the SoftOff state, the power
supply provides power to keep the required circuitry in the system alive. In case the
system malfunctions and you want to turn off the power, just depress and hold the
power button for 4 seconds. The power will turn off and no power will be provided
to the motherboard.

Wake-On-LAN (WOL)

Wake-On-LAN is defi ned as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and access
tracking can occur after hours and on weekends so that daily LAN traffi c is kept
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. Wake-On-LAN must be enabled in BIOS.

1-7 Power Supply

As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.

Please refer to the pinout information for the power connectors in Section 2-7 of
Chapter 2 for detailed information on power requirements for the H8SGL(-F).

In areas where noisy power transmission is present, you may choose to install a
line fi lter to shield the computer from noise. It is recommended that you also install
a power surge protector to help avoid problems caused by power surges.

Warning: To prevent the possibility of explosion, do not use the wrong type of
onboard CMOS battery or install it upside down.

Chapter 1: Introduction

1-13

1-8 Super I/O

The disk drive adapter functions of the Super I/O Winbond® BMC chip includes a
data separator, write pre-compensation circuitry, decode logic, data rate selection,
a clock generator, drive interface control logic and interrupt and DMA logic. The
wide range of functions integrated onto the Super I/O greatly reduces the number
of components required for interfacing with fl oppy disk drives.

The Super I/O provides two high-speed, 16550 compatible serial communication
ports (UARTs), one of which supports serial infrared communication. Each UART
includes a 16-byte send/receive FIFO, a programmable baud rate generator,
complete modem control capability and a processor interrupt system. Both UARTs
provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced
speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed
modems.

The Super I/O provides functions that comply with ACPI (Advanced Confi guration
and Power Interface), which includes support of legacy and ACPI power management
through a SMI or SCI function pin. It also features auto power management to reduce
power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can be fl exibly adjusted
to meet ISA PnP requirements, which support ACPI and APM (Advanced Power
Management).