Supermicro SUPER 370DEI, SUPER 370DER, SUPER 370DE6 USER MANUAL

SUPER

SUPER 370DE6
SUPER 370DER
SUPER 370DEI

®

USER’S MANUAL

Revision 2.0

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be contained
in this document, makes no commitment to update or to keep current the information in this
manual, or to notify any person or organization of the updates.

Please Note: For the most up-to-date version of this manual, please
see our web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa
Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total
liability for all claims will not exceed the price paid for the hardware product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2000-2001 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America.

Preface

PREFACE
About This Manual

This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use
of the SUPER 370DE6/370DER(370DER+)/370DEI(370DEI+) mainboard. The
SUPER 370DE6/370DER/370DER+/370DEI/370DEI+ supports single or dual
Pentium® III 500 MHz-1.13 GHz FCPGA processors with a 133/100 MHz
front side bus. Please refer to the support section of our web site (http://
www.supermicro.com/TechSupport.htm) for a complete listing of supported
processors.

Pentium III FCPGA (Flip Chip Pin Grid Array) processors are housed in a
370-pin socket, which is the standard that will support future Intel proces­sors. The 370DER/370DER+/370DEI/370DEI+ were designed specifically for
use in rackmount 1-U systems.

Manual Organization

Chapter 1 includes a checklist of what should be included in your

mainboard box, describes the features, specifications and performance of
the SUPER 370DE6/370DER/370DER+/370DEI/370DEI+ mainboard and pro­vides detailed information about the chipset.

Preface

Chapter 2 begins with instructions on handling static-sensitive devices.
Read this chapter when you want to install the processor and DIMM memory
modules and when mounting the mainboard in the chassis. Also refer to
this chapter to connect the floppy and hard disk drives, SCSI drives, the IDE
interfaces, the parallel and serial ports and the twisted wires for the power
supply, the reset button, the power LED, the speaker and the keyboard.

If you encounter any problems, see Chapter 3, which describes trouble­shooting procedures for the video, the memory and the setup configuration
stored in CMOS. For quick reference, a general FAQ [Frequently Asked
Questions] section is provided. Instructions are also included for contact­ing technical support. In addition, you can visit our web site at
www.supermicro.com/techsupport.htm for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup utility.

Appendix A gives information on BIOS error beep codes.

Appendix B provides post checkpoint codes.

iii

SUPER 370DE6/370DER/370DEI User’s Manual

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist .................................................................................................... 1-1

Contacting Supermicro ............................................................................ 1-2

Notes .......................................................................................................... 1-3

SUPER 370DE6 SECTION....................................................................... 1-4

SUPER 370DE6 Image ............................................................................. 1-5

SUPER 370DE6 Layout............................................................................ 1-6

SUPER 370DE6 Quick Reference.......................................................... 1-7

SUPER 370DER SECTION ...................................................................... 1-8

SUPER 370DER Image ............................................................................. 1-9

SUPER 370DER Layout ......................................................................... 1- 10

SUPER 370DER+ Layout ....................................................................... 1-1 1

SUPER 370DER Quick Reference ....................................................... 1-12

SUPER 370DER+ Quick Reference ..................................................... 1-13

SUPER 370DEI SECTION...................................................................... 1-14

SUPER 370DEI Image ............................................................................. 1-15

SUPER 370DEI Layout ........................................................................... 1- 16

SUPER 370DEI+ Layout......................................................................... 1 -17

SUPER 370DEI Quick Reference ......................................................... 1-1 8

SUPER 370DEI+ Quick Reference ....................................................... 1-1 9

General SECTION ................................................................................. 1-20

Features of Motherboards .................................................................... 1-21

Server Works HE-SL Chipset: System Block Diagram .....................1-23

1-2 Chipset Overview......................................................................................... 1-24

1-3 Special Features ........................................................................................... 1-24

ATI Graphics Controller ........................................................................ 1-2 4

BIOS Recovery ....................................................................................... 1-2 4

Recovery from AC Power Loss ......................................................... 1-2 4

1-4 PC Health Monitoring.................................................................................... 1-25

1-5 ACPI/PC 98 Features ................................................................................... 1-2 6

1-6 Power Supply ............................................................................................... 1 -28

1-7 Super I/O ......................................................................................................... 1-28

Chapter 2: Installation

2-1 Static-Sensitive Devices ............................................................................... 2-1

Precautions............................................................................................... 2-1

Unpacking.................................................................................................. 2-1

2-2 FCPGA Processor Installation ...................................................................... 2-2

2-3 Installing DIMMs............................................................................................... 2-4

iv

Table of Contents

Table of Contents

2-4 Port/Control Panel Connector Locations ..................................................... 2-5

2-5 Connecting Cables .......................................................................................... 2-8

Power Supply Connector ....................................................................... 2-8

Power LED ................................................................................................. 2-8

Hard Drive LED ........................................................................................ 2-8

PWR_ON .................................................................................................... 2-9

NIC_LED ..................................................................................................... 2-9

Reset.......................................................................................................... 2-9

I2C ................................................................................................................ 2-9

Chassis Intrusion ................................................................................... 2-10

Keyboard Lock ....................................................................................... 2-1 0

Overheat LED ......................................................................................... 2-1 0

Extra Universal Serial Bus Connection (USB3) ................................ 2- 10

Speaker ................................................................................................... 2-11

Fan Headers ........................................................................................... 2-11

Serial Ports ............................................................................................. 2- 11

ATX PS/2 Keyboard and Mouse Ports ................................................2-11

Universal Serial Bus Connector .......................................................... 2 -12

Extra Universal Serial Bus Connection (USB4) ................................ 2- 12

Wake-On-LAN ......................................................................................... 2-12

Power Supply Fail Header ................................................................... 2 -13

SLED1 (SCSI LED) Indicator................................................................. 2-1 3

2-6 DIP Switch Settings ..................................................................................... 2- 14

DIP Switch 1: Core/Bus Ratio .............................................................. 2-14

2-7 Jumper Settings ............................................................................................ 2-1 4

CMOS Clear............................................................................................. 2-1 5

Front Side Bus Speed .......................................................................... 2-1 5

SCSI Termination Enable/Disable.......................................................... 2-16

Speaker Enable/Disable ......................................................................... 2-16

Onboard LAN/NIC Enable/Disable......................................................... 2-16

Third Power Supply Failure Alarm Enable/Disable ........................... 2-17

2-8 Parallel Port, Floppy/Hard Disk Drive and SCSI Connections ............... 2-1 7

Parallel Port Connector ......................................................................... 2-1 7

Floppy Connector ................................................................................... 2-18

IDE Connectors ...................................................................................... 2-18

Ultra160 SCSI Connector ....................................................................... 2-19

Installing Software Drivers .................................................................. 2- 20

v

SUPER 370DE6/370DER/370DEI User’s Manual

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................ 3-1

Before Power On .................................................................................... 3-1

No Power .................................................................................................. 3-1

No Video ................................................................................................... 3-1

Memory Errors .......................................................................................... 3-2

Losing the System’s Setup Configuration ........................................... 3-2

3-2 Technical Support Procedures .................................................................... 3-2

3-3 Frequently Asked Questions ........................................................................ 3-3

3-4 Returning Merchandise for Service ............................................................ 3-5

Chapter 4: BIOS

4-1 Introduction....................................................................................................... 4-1

4-2 BIOS Features ................................................................................................. 4-2

4-3 Running Setup ................................................................................................. 4-2

Standard CMOS Setup ............................................................................. 4-3

4-4 Advanced CMOS Setup .................................................................................. 4-4

4-5 Chipset Setup ................................................................................................. 4-15

4-6 PCI/Plug and Play Setup ............................................................................... 4-18

4-7 Power Setup .................................................................................................. 4-22

4-8 Boot Setup ...................................................................................................... 4-25

4-9 Security Setup ............................................................................................... 4-27

4-10 Exit Setup ....................................................................................................... 4-29

Appendices:

Appendix A: BIOS Error Beep Codes .................................................................... A-1

Appendix B: AMIBIOS Post Checkpoint Codes .................................................... B-1

vi

SUPER 370DE6/370DER/370DEI User’s Manual

Notes

viii

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac­knowledged leader in the industry. Supermicro boards are designed with
the utmost attention to detail to provide you with the highest standards in
quality and performance.

Please check that the following items have all been included with your
motherboard. If anything listed here is damaged or missing, contact your
retailer.

One (1) Supermicro Mainboard

One (1) ribbon cable for IDE devices

Introduction

One (1) floppy ribbon cable for (a) 5.25-inch floppy and
(b) 3.5-inch floppy drives

One (1) I/O backpanel shield

SCSI Accessories (not with 370DEI/370DEI+):

One (1) 50-pin Ultra SCSI cable (370DE6 only)

One (1) 68-pin LVD SCSI cable

One (1) set of SCSI driver diskettes

One (1) SCSI manual

One (1) Supermicro CD or diskettes containing drivers and utilities

One (1) User's/BIOS Manual

1-1

SUPER 370DE6/370DER/370DEI User's Manual

CONTACTING SUPERMICRO

Introduction

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Avenue

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] (General Information)

[e-mail] (Technical Support)
Web site: www.supermicro.com

European Office

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML,

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: 6th Floor, No. 755 Chung-cheng Road

Chung-Ho City, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]

www : www.supermicro.com.tw
Email: [e-mail]

1-2

Notes

Chapter 1: Introduction

Introduction

1-3

SUPER 370DE6/370DER/370DEI User's Manual

Introduction

SUPER 370DE6

SECTION

1-4

SUPER 370DE6

Figure 1-1. SUPER 370DE6 Image

Chapter 1: Introduction

Introduction

1-5

SUPER 370DE6/370DER/370DEI User's Manual

Figure 1-3. SUPER 370DE6 Layout

Introduction

PS/2 KB/

J18

MOUSE

USB

COM1

J16

Parallel

Port

COM2

LAN

JP58

(*Notes: Memory modules should be installed in pairs only.)

CPU

FAN2

JP61

CPU

FAN1

(not drawn to scale)

ATX POWER #1

CPU

1

CPU

2

AGP PRO

3V/PCI64#2

3V/PCI64#1

5V/PCI64#4

5V/PCI64#3

5V/PCI64#2

5V/PCI64#1

13"

NORTH
BRIDGE

PWR_SEC

J19

JP1

JP3

1

SOUTH
BRIDGE

JP59

JP60

AIC-7899

0
K
N
A
B

JBT1

1

Bank0

Bank1

ATX POWER #2

J13

J15

E #1
ID

WOL

JP56

PPY
FLO

JF1

)

hannel B
I (C

S

ltra SC
U

JA5

JA3

JA1

JA4

Speaker

JP62

POWER LED

OH FAN

CHASSIS FAN

OH FAN

CHASSIS FAN

®

SUPER 370DE6

ULTRA160 LVD SCSI CHB

ULTRA160 LVD SCSI CHA

SLED

JP54

JP55

0

1

1

K

K

N

NK

N

A

A

A

B

B

B

E #2
ID

J14

BIOS

Y

R

E

T

T

A

B

1

SW1

JP57

SUPER

I/O

WOR

JA6 JA2

Also see the figure on page 2-5 for the locations of the I/O ports and
2-7 for the Front Control Panel (JF1) connectors.

1-6

Chapter 1: Introduction

370DE6 Quick Reference

Jumpers Description Default Setting

JA2 LVD SCSI Ch A Term. Open (Enabled)
JA4 LVD SCSI Ch B Term. Open (Enabled)
JA6 50pin SCSI Ch B Term Open (Enabled)
JBT1 CMOS Clear Pin 1-2 (Normal)
JP1 FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Open (Disabled)
JP55 Third P/S Fail Enable/Disable Off (Disabled)
JP56 Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN/NIC Enable/Disable Off (Enabled)
JP60 SCSI Enable/Disable Pin 1-2 (Enabled)

DIP Switch Description Default Setting
SW1(1-4) CPU Core/Bus Ratio

Connectors Description

ATX POWER #1 Primary ATX Power Connector
ATX POWER #2 Secondary ATX Power Connector BANK0­BANK1 Memory (RAM) Slots
COM1/COM2 COM1/COM2 Serial Port Connector
CPU1/CPU2 CPU 1 and CPU2 Sockets
CPU/CH/OH FAN CPU/Overheat/Chassis Fan Headers
J13, J14 IDE Hard Disk Drive Connectors
J15 Floppy Disk Drive Connector
J16 Parallel Printer Port
J18 PS/2 Keyboard/Mouse
LAN Ethernet Port
JA1 Ultra160 LVD SCSI CH A Connector
JA3 Ultra160 LVD SCSI CH B Connector
JF1 Front Control Panel
JP54 Third Power Supply Fail Header
PWR_SEC Secondary ATX Power Connector
SLED1 SCSI Active LED header
USB Universal Serial Bus Ports
WOL Wake-on-LAN Header
WOR Wake-on-Ring Header

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

Introduction

1-7

SUPER 370DE6/370DER/370DEI User's Manual

Introduction

SUPER 370DER

SECTION

1-8

SUPER 370DER

Figure 1-2. SUPER 370DER Image

Chapter 1: Introduction

Introduction

1-9

SUPER 370DE6/370DER/370DEI User's Manual

Figure 1-4. SUPER 370DER Layout

Introduction

(not drawn to scale)

PS/2 KB/

MOUSE

USB

COM1

J16

Parallel

Port

VGA

LAN1

LAN2

JP58

JP61
JP60

J18

1

J11

JP62

JA3

CPU

FAN1

Rage XL

VGA

AIC-7899

ULTRA160 LVD SCSI CHB

COM2

3V/PCI64

1

JP64

CPU

1

CPU

2

ATX POWER

CPU

FAN2

11.475"

JA6 JA2

NORTH
BRIDGE

SOUTH
BRIDGE

JA4

PWR_SEC

JP1

1

SLED

JP3

JP59

JP63

BIOS

J19

JP57

SW1

SUPER

I/O

WOR

0
K
N
A
B

WOL

Bank1Bank0

1
K
N
A
B

PY
P

FLO

J15

1

JBT1

T

A

B

JP56

OVERHEAT FAN

0
K
N
A
B

E #2
ID

J13 J14

Y

R

E

T

POWER LED

1

PWR LED

JF1

OH FAN

J214

JP65

CHASSIS FAN

1
K

AN
B

CHASSIS FAN

E #1
ID

®

SUPER 370DER

JA1

ULTRA160 LVD SCSI CHA

SPEAKER

(*Notes: Memory modules should be installed in pairs only.)

Also see the figure on page 2-6 for the locations of the I/O ports and
2-7 for the Front Control Panel (JF1) connectors.

1-10

PS/2 KB/
MOUSE

USB

COM1

VGA

J18

Figure 1-4. SUPER 370DER+ Layout

(not drawn to scale)

11.475"

PWR_SEC

CPU

FAN1

CPU

1

ATX POWER

NORTH
BRIDGE

J19

Chapter 1: Introduction

Bank1

Bank0

1

PWR LED

JF1

OH FAN

J214

JP65

1

0
K
N

BA

0
K
N

NK
A
B

BA

1
NK

A
B

CHASSIS FAN

Introduction

AIC-7899

3V/PCI64

1

JP64

CPU

2

CPU

FAN2

JA6 JA2

SOUTH
BRIDGE

JA4

JP1

JP3

1

#2

PPY

E
ID

FLO

SLED

JP59

JP63

BIOS

SW1

JP57

SUPER

I/O

WOR

WOL

J15

1

JBT1

T

T

A

B

JP56

OVERHEAT FAN

Y

R

E

POWER LED

LAN1

LAN2

1

JP61
JP60

J11

JP62

JP58

JA5

EXT ULTRA160 LVD SCSI CHB

COM2

Rage XL

VGA

(*Notes: Memory modules should be installed in pairs only.)

Also see the figure on page 2-6 for the locations of the I/O ports and
2-7 for the Front Control Panel (JF1) connectors.

CHASSIS FAN

#1
E

ID

®

J13 J14

SUPER 370DER

JA1

ULTRA160 LVD SCSI CHA

SPEAKER

1-11

SUPER 370DE6/370DER/370DEI User's Manual

370DER Quick Reference

Jumpers Description Default Setting

JA2 LVD SCSI Ch A Term. Open (Enabled)

Introduction

JA4 LVD SCSI Ch B Term. Open (Enabled)
JA6 Manufacturer's Setting Always Closed
JBT1 CMOS Clear Pin 1-2 (Normal)
JP1 FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Closed (Disabled)
JP56 Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN1 Enable/Disable Off (Enabled)
JP60 VGA Enable/Disable Pin 2-3 (Enabled)
JP61 VGA Interrupt Enable Pin 2-3 (Enabled)
JP62 LAN2 Enable/Disable Off (Enabled)
*JP63

(Notes) Chipset Speed Setting Off (133 MHz)

JP64 SCSI Enable/Disable Pin 1-2 (Enabled)
(*Note 1: for 370DER V.1.00 only.)
(*Note 2: If the FSB speed is 100MHz, JP63 should be set to "on".)

DIP Switches Description Default Setting
SW1(1-4) CPU Core/Bus Ratio

Connectors Description

ATX POWER Primary ATX Power Connector
BANK0/BANK1 Memory (RAM) Slots
COM1/COM2 COM1/2 Serial Port Conn/Header
CPU/CH/OH FAN CPU/Overheat/Chassis Fan Headers
J13, J14 IDE Hard Disk Drive Connectors
J15 Floppy Disk Drive Connector
J16 Parallel Printer Port
J18 PS/2 Keyboard/Mouse
J214 USB0 Header
JA1 Ultra160 Channel A LVD SCSI
JA3 Ultra160 Channel B LVD SCSI
JF1 Front Control Panel
LAN1/LAN2 Ethernet Port 1 / Ethernet Port 2
PWR_SEC Secondary ATX Power Connector
SLED1 SCSI Active LED header
USB Universal Serial Bus Ports
VGA Onboard VGA Monitor Connector
WOL Wake-on-LAN Header
WOR Wake-on-Ring Header

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

1-12

Chapter 1: Introduction

370DER+ Quick Reference

Jumpers Description Default Setting

JA2 LVD SCSI Ch A Term. Open (Enabled)
JA4 LVD SCSI Ch B Term. Open (Enabled)
JA6 Manufacturer's Setting Always Closed
JBT1 CMOS Clear Pin 1-2 (Normal)
JP1 FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Open (Disabled)
JP56 Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN1 Enable/Disable Off (Enabled)
JP60 VGA Enable/Disable Pin 2-3 (Enabled)
JP61 VGA Interrupt Enable Pin 2-3 (Enabled)
JP62 LAN2 Enable/Disable Off (Enabled)
*JP63

(Notes) Chipset Speed Setting Off (133 MHz)

JP64 SCSI Enable/Disable Pin 1-2 (Enabled)
(*Note1 : 370DER+ V.1.00 only.)
(*Note2 : If the FSB speed is 100MHz, JP63 should be set to "On".)

DIP Switches Description Default Setting
SW1(1-4) CPU Core/Bus Ratio

Introduction

Connectors Description

ATX POWER Primary ATX Power Connector
BANK0/BANK1 Memory (RAM) Slots
COM1/COM2 COM1/2 Serial Port Conn/Header
CPU/CH/OH FAN CPU/Overheat/Chassis Fan Headers
J13, J14 IDE Hard Disk Drive Connectors
J15 Floppy Disk Drive Connector
J18 PS/2 Keyboard/Mouse
J214 USB0 Header
JA1 Ultra160 Channel A LVD SCSI
JA5 External U160 Channel B LVD SCSI
JF1 Front Control Panel
LAN1/LAN2 Ethernet Port 1 / Ethernet Port 2
PWR_SEC Secondary ATX Power Connector
SLED1 SCSI Active LED header
USB Universal Serial Bus Ports
VGA Onboard VGA Monitor Connector
WOL Wake-on-LAN Header
WOR Wake-on-Ring Header

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

1-13

SUPER 370DE6/370DER/370DEI User's Manual

Introduction

SUPER 370DEI

SECTION

1-14

SUPER 370DEI

Chapter 1: Introduction

Figure 1-2. SUPER 370DEI Image

Introduction

1-15

SUPER 370DE6/370DER/370DEI User's Manual

Figure 1-4. SUPER 370DEI Layout

Introduction

(not drawn to scale)

12.05"

12.05"

PS/2 KB/
MOUSE

USB

COM1

J16

Parallel

Port

VGA

LAN1

LAN2

JP58

JP61

JP60

J18

1

JP62

J11

COM2

CPU
FAN1

Rage XL

VGA

CPU

CPU

3V/PCI64

ATX POWER

1

2

CPU

FAN2

11.475"

NORTH
BRIDGE

SOUTH
BRIDGE

Bank1Bank0

1

PWR LED

JF1

OH FAN

J214

JP65

E #1

E #2

ID

ID

J13 J14

Y

R

SPEAKER

CHASSIS FAN

1
K
N

BA

CHASSIS FAN

®

SUPER 370DEI

1

0
K
N
A
B

JP1

JP3

1

JP63

JP59

SW1

SUPER

I/O

BIOS

JP57

K
N
A
B

PY
P

FLO

J15

1

JBT1

T

A

B

JP56

OVERHEAT FAN

0
K
N
A
B

E

T

POWER LED

(*Notes: Memory modules should be installed in pairs only.)

Also see the figure on page 2-6 for the locations of the I/O ports and
2-7 for the Front Control Panel (JF1) connectors.

1-16

Chapter 1: Introduction

Figure 1-4. SUPER 370DEI+ Layout

(not drawn to scale)

12.05"

12.05"

PS/2 KB/

MOUSE

USB

COM1

VGA

LAN1

LAN2

JP58

JP61
JP60

J18

1

J11

JP62

COM2

CPU

FAN1

Rage XL

VGA

CPU

CPU

3V/PCI64

ATX POWER

1

2

CPU

FAN2

11.475"

NORTH
BRIDGE

SOUTH
BRIDGE

Bank1Bank0

PWR LED

J214

JP65

1

0

K

K

N
A

AN

B

B

JP1

JP3

1

JP59

JP63

BIOS

SW1

JP57

SUPER

I/O

J15

JP56

0
K
N
A
B

Y
PP

FLO

1

JBT1

R

E

T

T

A

B

OVERHEAT FAN

POWER LED

1
K
N
A
B

#1

#2

E

E

ID

ID

J13 J14

Y

SPEAKER

CHASSIS FAN

®

SUPER 370DEI

Introduction

1

JF1

OH FAN

CHASSIS FAN

(*Notes: Memory modules should be installed in pairs only.)

Also see the figure on page 2-6 for the locations of the I/O ports and
2-7 for the Front Control Panel (JF1) connectors.

1-17

SUPER 370DE6/370DER/370DEI User's Manual

370DEI Quick Reference

Jumpers Description Default Setting

Introduction

JBT1 CMOS Clear Pin 1-2 (Normal)
JP1 FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Open (Disabled)
JP56 Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN1 Enable/Disable Off (Enabled)
JP60 VGA Enable/Disable Pin 2-3 (Enabled)
JP61 VGA Interrupt Enable Pin 2-3 (Enabled)
JP62 LAN2 Enable/Disable Off (Enabled)
*JP63 Chipset Speed Setting Off (133 MHz)

(*Note1 : If the FSB speed is 100MHz, JP63 should be set to "On".)

DIP Switches Description Default Setting
SW1(1-4) CPU Core/Bus Ratio

Connectors Description

ATX POWER Primary ATX Power Connector
BANK0/BANK1 Memory (RAM) Slots
COM1/COM2 COM1/2 Serial Port Conn/Header
CPU/CH/OH FAN CPU/Overheat/Chassis Fan Headers
J13, J14 IDE Hard Disk Drive Connectors
J15 Floppy Disk Drive Connector
J16 Parallel Printer Port
J18 PS/2 Keyboard/Mouse
J214 USB0 Header
JA1 Ultra160 Channel A LVD SCSI
JA5 External U160 Channel B LVD SCSI
JF1 Front Control Panel
LAN1/LAN2 Ethernet Port 1 / Ethernet Port 2
PWR_SEC Secondary ATX Power Connector
USB Universal Serial Bus Ports
VGA Onboard VGA Monitor Connector
WOL Wake on Lan
WOR Wake on Ring

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

1-18

Chapter 1: Introduction

370DEI+ Quick Reference

Jumpers Description Default Setting

JBT1 CMOS Clear Pin 1-2 (Normal)
JP1 FSB Speed Setting Pin 1-2 (Auto)
JP3 Spread Spectrum Enable Open (Disabled)
JP56 Speaker Enable/Disable On (Enabled)
JP57 BIOS Select Pin 1-2 (BIOS1)
JP58 LAN1 Enable/Disable Off (Enabled)
JP60 VGA Enable/Disable Pin 2-3 (Enabled)
JP61 VGA Interrupt Enable Pin 2-3 (Enabled)
JP62 LAN2 Enable/Disable Off (Enabled)
*JP63 Chipset Speed Setting Off (133 MHz)

(*Note1 : If the FSB speed is 100MHz, JP63 should be set to "On".)

DIP Switches Description Default Setting
SW1(1-4) CPU Core/Bus Ratio

Connectors Description

ATX POWER Primary ATX Power Connector
BANK0/BANK1 Memory (RAM) Slots
COM1/COM2 COM1/2 Serial Port Conn/Header
CPU/CH/OH FAN CPU/Overheat/Chassis Fan Headers
J13, J14 IDE Hard Disk Drive Connectors
J15 Floppy Disk Drive Connector
J18 PS/2 Keyboard/Mouse
J214 USB0 Header
JA1 Ultra160 Channel A LVD SCSI
JA5 External U160 Channel B LVD SCSI
JF1 Front Control Panel
LAN1/LAN2 Ethernet Port 1 / Ethernet Port 2
PWR_SEC Secondary ATX Power Connector
USB Universal Serial Bus Ports
VGA Onboard VGA Monitor Connector
WOL Wake on Lan
WOR Wake on Ring

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

Introduction

1-19

SUPER 370DE6/370DER/370DEI User's Manual

Introduction

GENERAL
SECTION

1-20

Chapter 1: Introduction

Features of the 370DE6/370DER/370DER+/370DEI

CPU

• Single or dual Pentium III FCPGA 500 MHz-1.13 GHz processors at 133
or 100 MHz front side bus

Note: Please refer to the support section of our web site for a complete listing of supported
processors. (http://www.supermicro.com/TechSupport.htm)

Memory

• Four 168-pin DIMM sockets supporting up to 4 GB registered ECC
SDRAM

Note 1: The memory speed must match the front side bus speed being used. (Both

133 or 100 MHz.)

Note 2: The DIMM slots on the 370DER are set at a 25° angle to provide a low

vertical profile.

Note 3: Memory Modules should be installed in pairs (first in the two slots of Bank0,

then in both slots of Bank1, if needed).

Chipset

• ServerWorks ServerSet III HE Super Light (see page 1-13 for details)

Expansion Slots

370DE6: 370DER/DER+/DEI:

• Two 64-bit, 66/33 MHz PCI slots • One 64-bit, 66/33 MHz PCI

• Four 64-bit, 33 MHz PCI slots slot

• One 2x/AGP Pro slot

Introduction

BIOS

• 4 Mb AMI® Flash ROM

• APM 1.2, DMI 2.1, PCI 2.2, ACPI 1.0, Plug and Play (PnP)

PC Health Monitoring

• Seven onboard voltage monitors for CPU core, chipset voltage, +5V
and +12V

• Fan status monitor with firmware/software on/off control

• Environmental temperature monitor and control

• CPU fan auto-off in sleep mode

• Power-up mode control for recovery from AC power loss

• System overheat LED and control

• System resource alert

1-21

SUPER 370DE6/370DER/370DEI User's Manual

ACPI/PC 98 Features

• Microsoft OnNow

Introduction

• Slow blinking LED for suspend state indicator

• Main switch override mechanism

• External modem ring-on

Onboard I/O

• AIC-7899 for dual channel Ultra160 SCSI (370DE6/370DER/370DER+)

• Integrated ATI Rage XL Graphics Controller (370DER/370DER+/370DEI)

• Intel 82559 for integrated onboard Ethernet (370DER/370DER+/370DEI)

• 2 EIDE bus master interfaces support Ultra DMA/33

• 1 floppy port interface (up to 2.88 MB)

• 2 Fast UART 16550A compatible serial ports

• 1 EPP/ECP (Enhanced Parallel Port/Extended Capabilities Port)

(370DE6/370DER/370DEI)

• PS/2 mouse and PS/2 keyboard ports

• 2 USB (Universal Serial Bus) ports

Other

• Internal/external modem ring-on

• Recovery from AC power loss control

• Wake-on-LAN (WOL)

CD/Diskette Utilities

• BIOS flash upgrade utility

• Device Drivers

Dimensions

• SUPER 370DE6
Extended ATX: 12.05" x 13" (306 x 330 mm)

• SUPER 370DER/370DER+/370DEI
Full ATX: 12.05" x 11.475" (306 x 291 mm)

1-22

g

PCI 64/33

Pe n tiu m III

FCPGA

CPU*

133/100 MHz Host Bus

Pe n tiu m III

FCPGA

CPU*

Chapter 1: Introduction

PC133/PC100

istered

Re

DIMMs

ECC

Introduction

CIOB20

CNB20HE-SL

Hos t (N o rth ) Bridge

Address & Control

144-bit Data Bus

PCI 64/66

USB

1.5 Mb/sec

OSB4

South Bridge

Ports

ATA33 IDE

BIOS 4Mb

Flash ROM

Ports

Figure 1-5. ServerWorks HE-SL Chipset:

System Block Diagram

*Note: This is a general block diagram. Please see the previous

Motherboard Features Section for details on the PCI slots included

on each motherboard.

1-23