Supermicro FatTwin F617H6-FTL+, FatTwin F617H6-FTPTL+, FatTwin F627G2-FTPT+, FatTwin F627G2-FT+, FatTwin F627G2-F73+ User Manual

...

Download

SUPER

USER'S MANUAL

Revision 1.1a

FatTwin

F617H6-FTL+

F617H6-FTPTL+

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at

www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.

Revision 1.1a Release Date: January 23, 2015

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the FatTwin™ F617H6-FTL+/FTPTL+. Installation and maintainance should be performed by experienced technicians only .

The FatTwin F617H6-FTL+/FTPTL+ is a high-end server based on the F414IS-R1K62B 4U rackmount chassis and a dual processor X9DRFF-7G+/7TG+ serverboard. All models have four serverboard nodes each with an IPMI LAN port and twelve (12) 3.5" ﬁ xed HDD drives and two (2) 2.5" optional ﬁ xed HHD drives each per node. The F617H6-FTPTL+ server uses 10-Gigabit LAN ports whereas the F617H6-FTL+ server uses Gigabit LAN ports.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with the server system and describes the main features of the X9DRFF-7G+/7TG+ serverboards and the F414IS-R1K62B chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the FatTwin F617H6-FTL+/FTPTL+ into a rack and check out the server conﬁ guration prior to powering up the system. If your server was ordered without processor and memory components, this chapter will refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the FatTwin F617H6-FTL+/FTPTL+.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRFF-7G+/7TG+ serverboards, including the locations and functions of connections, headers and jumpers. Refer to this chapter when adding or removing processors or main memory and when reconﬁ guring the serverboard.

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the F414IS-R1K62B server chassis. You should follow the procedures given in this chapter when installing, removing or reconﬁ guring SATA or peripheral drives and when replacing system power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes Appendix B: System Speciﬁ cations

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Notes

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Onboard SAS .................................................................................................. 1-2

Onboard Serial ATA ........................................................................................1-3

PCI Expansion Slots ....................................................................................... 1-3

I/O Ports ..........................................................................................................1-3

Graphics Controller ......................................................................................... 1-3

Nuvoton WPCM450 Controller .......................................................................1-3

WPCM450R DDR2 Memory Interface ....................................................... 1-4

WPCM450R PCI System Interface ............................................................ 1-4

Other Features Supported by the WPCM BMC Controller ........................ 1-4

SATA Drive Power ........................................................................................... 1-5

Super I/O ......................................................................................................... 1-5

1-3 Server Chassis Features ................................................................................1-5

System Power ................................................................................................. 1-5

SAS/SATA Subsystem .....................................................................................1-5

I/O Ports ..........................................................................................................1-5

Cooling System ............................................................................................... 1-6

Air Shrouds ..................................................................................................... 1-6

Mounting Rails ................................................................................................ 1-6

1-4 Advanced Power Management ....................................................................... 1-6

Intel® Intelligent Power Node Manager (NM) .................................................1-6

Manageability Engine (ME) ............................................................................. 1-6

1-5 Contacting Supermicro ....................................................................................1-8

1-6 Fat Twin: System Notes .................................................................................. 1-9

Nodes ..............................................................................................................1-9

System Power ................................................................................................. 1-9

SAS/SATA Backplane/Drives .......................................................................... 1-9

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Warnings and Precautions .............................................................................. 2-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

vii

Choosing a Setup Location .............................................................................2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions ..........................................................................................2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airﬂ ow ......................................................................................... 2-3

Mechanical Loading ...................................................................................2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-4

2-5 Rack Mounting Instructions .............................................................................2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

Adjusting the Rails .......................................................................................... 2-4

Locking Tabs ...................................................................................................2-5

Installing the Rails on a Rack ......................................................................... 2-6

Chassis Installation ......................................................................................... 2-7

2-6 Checking the Serverboard Setup ....................................................................2-8

2-7 Checking the Drive Bay Setup ........................................................................2-9

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-3 F414IS Front I/O Control Panel ...................................................................... 3-1

3-4 Control Panel LEDs ........................................................................................3-2

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Deﬁ nition ........................................................................................... 4-1

Installation Instructions ....................................................................................4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................4-10

Redundant Power Supplies ..........................................................................4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning .................................................................................4-16

Power Cable and AC Adapter ...................................................................... 4-18

Table of Contents

viii

Chapter 5 Advanced Motherboard Setup

5-1 Handling the Motherboard ..............................................................................5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Connecting Cables .......................................................................................... 5-2

Connecting SATA Power Cables .....................................................................5-2

Connecting Data Cables ................................................................................. 5-2

5-3 Control Panel Connectors and I/O Ports ........................................................ 5-2

5-4 Processor and Heatsink Installation................................................................5-3

Installing a CPU Heatsink ............................................................................... 5-7

Removing the Heatsink ................................................................................... 5-7

5-5 Installing Memory ............................................................................................5-8

Removing Memory Modules ........................................................................... 5-9

Memory Support ..............................................................................................5-9

5-6 Serverboard Details ...................................................................................... 5-16

5-7 Connector Deﬁ nitions .................................................................................... 5-19

5-8 Jumper Settings ............................................................................................ 5-23

Explanation of Jumpers ................................................................................5-23

5-9 Onboard Indicators ........................................................................................5-25

5-10 Serial ATA Connections ................................................................................. 5-27

5-11 Installing Drivers ............................................................................................5-28

SuperDoctor III .............................................................................................. 5-29

5-12 Serverboard Battery ......................................................................................5-31

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

Unpacking .......................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 Removing the Power Cord ..............................................................................6-3

6-4 Removing Nodes from the Chassis ................................................................ 6-3

6-5 Removing the Node Cover..............................................................................6-4

6-6 Installing and Removing Hard Drives ............................................................. 6-5

Replacing Fixed 3.5" Hard Drives ...................................................................6-6

6-7 Node Conﬁ guration .........................................................................................6-7

6-8 Removing and Installing the Backplane ..........................................................6-8

Removing the Backplane ................................................................................ 6-8

6-9 Power Adapter Board Replacement ..............................................................6-10

6-10 Installing the Motherboard ............................................................................6-11

Compatible Motherboards ..............................................................................6-11

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Permanent and Optional Standoffs ................................................................6-11

6-11 Installing Expansion Cards ...........................................................................6-13

PCIE Slot Setup ............................................................................................ 6-13

Installing a Low-Proﬁ le Expansion Card ....................................................... 6-14

Installation Complete .....................................................................................6-15

6-12 Replacing Exhaust Fans ............................................................................... 6-16

6-13 Replacing the Power Supply .........................................................................6-18

Power Supply Replacement ..........................................................................6-19

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility ..............................................................................7-1

How To Change the Conﬁ guration Data ......................................................... 7-2

Starting the Setup Utility ................................................................................. 7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Conﬁ gurations...................................................................... 7-3

7-4 Event Logs .................................................................................................... 7-23

7-5 IPMI ............................................................................................................... 7-25

7-6 Boot ............................................................................................................... 7-27

7-7 Secur ity ......................................................................................................... 7-28

7-8 Save & Exit ................................................................................................... 7-29

Appendix A System Speciﬁ cations

Table of Contents

Notes

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Chapter 1

Introduction

1-1 Overview

The FatTwin F617H6-FTL+/FTPTL+ is a high-end server comprised of two main subsystems: the F414IS-R1K62B 4U server chassis and the X9DRFF-7G+/7TG+ dual processor serverboard in four hot-swap nodes. Please refer to our web site for information on operating systems that have been certiﬁ ed for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been included with the FatTwin F617H6-FTL+/FTPTL+ server, as listed below:

• Four (4) 1U passive front CPU heat sinks (SNK-P0047PSC)

• Four (4) 1U passive CPU heat sinks for MB w/ narrow ILM (SNK-P0047PS)

• Four (4) power adapter boards (BPN-ADP-F418L-O-P)

• Power Cables:

Four (4) 8pin to 2x2pin (50cm) and 2 SATA power connectors (46cm) and (16cm) 18AWG power cables (CBL-PWEX-0511-01) Four (4) 8 pin to 2 2x2(50/60-cm) and 2 SATA (26+16-cm) 18AWG power cables (CPL-PWEX-0485-01)

• SAS/SATA Backplane and accessories:

Four (4) backplanes for twelve (12) 3.5" HDD ( BPN-SAS-816T-A3-O-P) Eight (8) 1U Hadroop backplanes for thirty-two (32) 3.5" HDD (BPN-SAS-816T-A4-O-P) Twelve (12) 21-cm 30AWG SATA S-S cables (CBL-0473L) Eight (8) 29-cm 30AWG SATA S-S cables (CBL-0483L) Twelve (12) 81-cm 30AWG SATA S-S cables (CBL-0481L) Eight (8) 29-cm 30AWG SATA S-S cables (CBL-0483L) Sixteen (16) 55-cm 30AWG SATA S-S cables (CBL-0484L)

• Riser Cards:

Four (4) 1U LHS FatTwin PCI-E x8 riser cards with (RSC-R1UFF-E8-O-P) Four (4) PCI-E x4 riser cards (RSC-R1UFF-E8R-O-P)

• One (1) F418/F424 rail set (MCP-290-41803-0N)

Chapter 1: Introduction

1-1

1-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Note: If you are using the optional PWS-2K02P-1R power supply you will need to use the C13 to C14 size 14AWG wire power cord set for the rack.

Note: For your system to work properly, please follow the links below to download all necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information:

http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

support@supermicor.com

1-2 Serverboard Features

At the heart of the FatTwin F617H6-FTL+/FTPTL+ lies the X9DRFF-7G+/7TG+, a dual processor serverboard based on the Intel® C602 chipset. Below are the main features of the serverboard. (See Figure 1-1 for a block diagram of the chipset.)

Processors

The X9DRFF-7G+/7TG+ supports single or dual Intel® E5-2600 series processors in Socket R LGA 2011 sockets. Please refer to the serverboard description pages on our web site for a complete listing of supported processors (www.supermicro.com).

Memory

The X9DRFF-7G+/7TG+ has sixteen (16) memory sockets that can support up to 512 GB of ECC registered RDIMMs or up to 128 GB of unbuffered ECC/non-ECC UDIMMs in DDR3-1600/1333/1066/800 MHz speed, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size, and .at 1.35 or 1.5 voltages. Please refer to Chapter 5 for installing memory.

Note: For the latest CPU/memory updates, please refer to our website at

http://www.supermicro.com/products/motherboard.

Onboard SAS

An LSI 2308 SAS controller provides eight SAS2 ports. The SAS drives are connected to a backplane that provides power, bus termination and conﬁ guration settings. RA ID 0, 1, and 10 are suppo rte d.

Note: The operating system you use must have RAID support to enable the hotswap c apabil ity an d R AID fu ncti on of the SA S drive s.

1-3

Chapter 1: Introduction

Onboard Serial ATA

A SATA controller is integrated into the chipset to provide a twelve-port SATA subsystem. Two of the por ts suppor t SATA 3. 0 (RAID 0 an d 1) a nd ten suppor t SATA 2. 0 (R AID 0, 1, 5 and 10). See Chapte r 5 for deta ils.

Note: The operating system you use must have RAID support to enable the hotswap c apabil ity an d RA ID fu nctio n of the SATA drives.

PCI Expansion Slots

Each node in the the FatTwin F617H6-FTL+/FTPTL+ has 1x PCI-E 3.0 x8 low-proﬁ le and 1x PCI-E 2.0 x4 low-proﬁ le expansion slots. Two riser cards are provided for each node for use with these expansion slots.

I/O Ports

The color-coded I/O ports located at the front of each node in the server include a VGA (monitor) port, two USB 2.0 ports, two 1 Gb Ethernet ports (X9DRFF-7G+) or two 10 Gb Ethernet ports (X9DRFF-7TG+) and one dedicated IPMI LAN port.

Note: For IPMI Conﬁ guration Instructions, please refer to the Embedded IPMI Configuration User's Guide available @ http://www.supermicro.com/support/

manuals/.

Graphics Controller

The X9DRFF-7G+/7TG+ features an integrated Matrox G200ew, 16 MB DDR2 graphics controller.

Nuvoton WPCM450 Controller

Note: The term "IPMI controller" and the term "BMC controller" can be used

interchangeably in this section. The Nuvoton WPCM450R Controller, a Baseboard Management Controller (BMC),

supports 2D/VGA-compatible Graphic Cores with PCI interface, creating multi-media virtualization via Keyboard/Video/Mouse Redirection (KVMR). The WPCM450R Controller is ideal for remote system management.

The WPCM450R Controller interfaces with the host system via PCI connections to communicate with the graphics cores. It supports USB 2.0 and 1.1 for remote keyboard/mouse/virtual media emulation. It also provides LPC interface support to control Super IO functions. The WPCM450R Controller is connected to the network via an external Ethernet PHY module or shared NCSI connections.

1-4

FatTwin F617H6-FTL+/FTPTL+ User's Manual

The WPCM450R communicates with onboard components via six SMBus interfaces, PECI (Platform Environment Control Interface) buses, and General Purpose I/O ports.

WPCM450R DDR2 Memory Interface

The WPCM450R supports a 16-bit DDR2 memory module with a speed of up to 220 MHz. For best signal integrity, the WPCM450R provides point-to-point connection.

WPCM450R PCI System Interface

The WPCM450R provides 32-bit, 33 MHz 3.3V PCI interface, which is compliant with the PCI Local Bus Speciﬁ cation Rev. 2.3. The PCI system interface connects to the onboard PCI Bridge used by the graphics controller.

Other Features Supported by the WPCM BMC Controller

The WPCM450R supports the following features:

• IPMI 2.0

• Serial over LAN

• KVM over LAN

• LAN Alerting-SNMP Trap

• Event Log

• X-Bus parallel interface for I/O expansion

• Multiple ADC inputs, Analog and Digital Video outputs

• SPI Flash Host BIOS and ﬁ rmware bootstrap program supported

• Reduced Media Independent Interface (RMII)

• OS (Operating System) Independency

• Provides remote Hardware Health Monitoring via IPMI. Key features

• Provides Network Management Security via remote access/console redirection.

• Supports the following Management tools: IPMIView, CLI (Command Line

Interface)

• RMCP+ protocol supported

Note: For more information on IPMI conﬁ guration, please refer to the IPMI User's Guide posted on our website at http://www.supermicro.com/support/manuals/.

1-5

Chapter 1: Introduction

SATA Drive Power

Please connect the onboard power cables (four each CBL-0511L and CBL-0485L) from each node's serverboard to the SATA backplane board in the node tray in order to provide power to the drives.

Super I/O

The Super I/O provides functions that comply with ACPI (Advanced Conﬁ guration and Power Interface), which includes support of legacy and ACPI power management through an SMI or SCI function pin. It also features auto power management to reduce power consumption.

1-3 Server Chassis Features

The following is a general outline of the main features of the F414IS server chassis.

System Power

The F414IS chassis model includes two high-efﬁ ciency 94%+ Platinum certiﬁ ed redundant 1620 Watt power supplies. In the unlikely event your power supply fails, replacement is simple and can be accomplished without tools.

SAS/SATA Subsystem

The F414IS supports up to twelve (12) ﬁ xed SAS/SATA drives (plus two (2) optional

2.5" SATA drives) for each node for a total of ﬁ fty-six (56) drives. The F414IS supports 3.5" and optional 2.5" hard drives. These drives are ﬁ xed units and are connected to three backplanes (that provides power and control) per node.

Note: For more information, visit our Web site at: http://www.supermicro.com.

I/O Ports

The F414IS is an proprietary form factor chassis designed to be used in a 4U rackmount conﬁ guration. The F414IS chassis provides two low-proﬁ le add-on card slots, a VGA port, two USB 2.0 ports, one IPMI Ethernet port and two gigabit (F617H6-FTL+) or two 10G (F617H6-FTPTL+) Ethernet ports per node.

1-6

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Cooling System

The F414IS chassis supports external exhaust fans that provide cooling for the system. The F617H6-FTL+/FTPTL+ server uses eight (8) 8-cm external system fans powered from either the backpane or the serverboards. When one of the motherboard nodes is removed, another motherboard will continue to operate the fans.

Air Shrouds

The F414IS chassis requires mylar air shrouds for each node to direct the airﬂ ow where cooling is needed. The air shroud will differ for different motherboards. If using a motherboard which is not the default in the chassis, refer to the optional parts in the Appendix of this manual, or the Supermicro Web site at www.supermicro.com to puchase the proper air shroud.

Mounting Rails

The F414IS includes a set of rails, and can be placed in a rack for secure storage and use. To setup your rack, follow the step-by-step instructions included in this manual.

1-4 Advanced Power Management

Intel® Intelligent Power Node Manager (NM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with real-time thermal control and power management for maximum energy efﬁ ciency. Although IPNM Speciﬁ cation Version 1.5 is supported by the BMC (Baseboard Management Controller), your system must also have IPNM-compatible Manageability Engine (ME) ﬁ rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O Hub), provides Server Platform Services (SPS) to your system. The services provided by SPS are different from those proveded by the ME on client platforms.

1-7

Chapter 1: Introduction

Figure 1-1. Intel C602 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly repre-

sent the features on your motherboard. See the previous pages for

the actual speciﬁ cations of your motherboard. This block diagram is

intended for your reference only.

P0 P1

PE2PE1 DMI

DDR3 DIMM

CPU1

E5-2600 Series Processor

Rear (Fan Side)

DDR3 DIMM

PE3

Gen3 x8 (0~7)

Gen3 x16 x16 Gen3 x8

Gen3 x16 Gen3 x8 (8~15) Gen3 x8 (0~7)

Gen2 x4

VGA CONN

LAN

RJ45 RJ45

PHY RTL8201F

LAN

X540

SAS2308

AT25321

6/3/1.5

3/1.5

6/3/1.5

I350 (2 ports)

PCI-Ex16x16

Proprietary SLOT

PCI-Ex16

Proprietary SLOT

PCI-Ex8 SLOT

SAS

DDR3 DIMM

PCH C602

PCI-Ex8 SLOT

PCI-Ex4 in x8 SLOT

AHCI

SATA

USB

SPI

USB

LPCPCI-32bit

DMI

PEG2_5:7

PEG2_0:4

DDR3 DIMM

QPI

Gen2 x4

SAS2 #4

SAS2 #3

SAS2 #2

SAS2 #1

SAS2 #8

SAS2 #7

SAS2 #6

SAS2 #5

WPCM450

VGA BMC

DDR2

DDR3 DIMM

P1 P0

PE2PE1 DMI

CPU0

E5-2600 Series Processor

Front (I/O Side)

PE3

SATA2 #3

SATA2 #4

SATA2 #5

SATA2 #6

SATA3 #1

SATA3 #2

Type A

Single

01 2

1-8

FatTwin F617H6-FTL+/FTPTL+ User's Manual

1-5 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information)

support@supermicro.com (Technical Support) Web Site:

www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.nl (General Information)

support@supermicro.nl (Technical Support)

rma@supermicro.nl (Customer Support) Web Site:

www.supermicro.nl

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C) Tel: +886-(2) 8226-3990 Fax: +886-(2) 8226-3992 Email: support@supermicro.com.tw Web Site:

www.supermicro.com.tw

1-9

Chapter 1: Introduction

1-6 Fat Twin: System Notes

As a FatTwin conﬁ guration, the FatTwin F617H6-FTL+/FTPTL+ is a unique server system. With four system boards incorporated into a single chassis acting as four separate nodes, there are several points you should keep in mind.

Nodes

Each of the four serverboards act as a separate node in the system. As independant nodes, each may be powered off and on without affecting the others. In addition, each node is a hot-swappable unit that may be removed from the rear of the chassis. The nodes are connected to the server backplane by means of an adapter card.

Note: A guide pin is located between the upper and lower nodes on the inner chassis wall. This guide pin also acts as a “stop” when a node is fully installed. If too much force is used when inserting a node this pin may break off. Take care to slowly slide a node in until you hear the “click” of the locking tab seating itself.

System Power

Four high-efﬁ ciency 94%+ Plus Platinum Level 1620 Watt power supplies are used to provide the power for all serverboards. Each serverboard however, can be shut down independently of the other with the power button on its own control panel.

SAS/SATA Backplane/Drives

As a system, the FatTwin F617H6-FTL+/FTPTL+ supports the use of up to ﬁ fty- six (56) drives SAS/SATA drives. Each of the backplanes in the system logically connects the internal ﬁ xed SAS/SATA drives to each node's backplane/serverboard. See Chapter 6 for the logical hard drive and node conﬁ guration.

1-10

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your FatTwin F617H6-FTL+/FTPTL+ up and running. Following these steps in the order given should enable you to have the system operational within a minimum amount of time. This quick setup assumes that your system has come to you with the processors and memory preinstalled. If your system is not already fully integrated with a serverboard, processors, system memory etc., please turn to the chapter or section noted in each step for details on installing speciﬁ c components.

2-2 Unpacking the System

You should inspect the box the FatTwin F617H6-FTL+/FTPTL+ was shipped in and note if it was damaged in any way. If the server itself shows damage you should ﬁ le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the FatTwin F617H6-FTL+/FTPTL+. It should be situated in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical noise and electromagnetic ﬁ elds are generated. You will also need it placed near a grounded power outlet. Read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the FatTwin F617H6-FTL+/FTPTL+ was shipped in should include two sets of rail assemblies, two rail mounting brackets and the mounting screws you will need to install the system into the rack. Follow the steps in the order given to complete the installation process in a minimum amount of time. Please read this section in its entirety before you begin the installation procedure outlined in the sections that follow.

2-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

2-4 Warnings and Precautions

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back of the rack to allow for sufﬁ cient airﬂ ow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the ﬂ oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack ﬁ rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Warning! To prevent bodily injury when mounting or servicing this unit in a

rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially ﬁ lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).

Reduced Airﬂ ow

Equipment should be mounted into a rack so that the amount of airﬂ ow required for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

2-4

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power strips, etc.).

2-5 Rack Mounting Instructions

This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. You should also refer to the installation instructions that came with the rack unit you are using.

Note: This rail will ﬁ t a rack between 26.5" and 36.4" deep. The SCF418 is not designed for installation into a Telco post-style rack unit.

Warning: Do not pick up the server with the front handles. They are

designed to pull the system from a rack only.

Stability Hazard: The rack stabilizing mechanism must be in place, or the rack must be bolted to the ﬂ oor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

Warning: When initially installing the server to a rack, test that the rail locking tabs engage to prevent the server from being overextended. Have a rack lift in place as a precaution in case the test fails.

Warning: In any instance of pulling the system from the rack, always use a rack lift and follow all associated safety precautions.

Identifying the Sections of the Rack Rails

The chassis package includes two rail assemblies in the rack mounting kit. Each assembly consists of three sections: An inner chassis rail which secures directly to the chassis, an outer rail that secures to the rack, and a middle rail which extends from the outer rail. These assemblies are speciﬁ cally designed for the left and right side of the chassis (see Figure 2-1).

Adjusting the Rails

Each rail assembly has an adjusting screw. loosening this screw allows you to adjust the length of the rail to ﬁ t a variety of rack sizes.

Chapter 2: Server Installation

2-5

Figure 2-1: Identifying the Outer Rail and Inner Rails

(Left Rail Assembly Shown)

Inner Rail

This Side Faces

Outward

Adjusting Screw

Outer Rail

Locking Tab

Locking Tabs

Each inner rail has a locking tab. This tab locks the chassis into place when installed and pushed fully into the rack. These tabs also lock the chassis in place when fully extended from the rack. This prevents the server from coming completely out of the rack when when the chassis is pulled out for servicing.

2-6

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Installing the Rails on a Rack

Installing the Rails

1. Adjust the length of both rails as described on the previous page.

2. Align the front section of the outer rail with the slots on the front post of the

rack. Secure the front of the outer rail to the rack with two screws.

3. Pull out the rear section of the outer rail, adjusting the length until it ﬁ ts within

the posts of the rack.

4. Align the rear section of the rail with the slots on the rear post of the rack.

Secure the rear of the outer rail to the rear of the rack with two screws.

5. Repeat steps 1-4 for the remaining rail.

Figure 2-2: Attaching the Rails to a Rack

Chapter 2: Server Installation

2-7

Note: The ﬁ gure above is for illustration purposes only. Always install servers to the bottom of the rack ﬁ rst.

Figure 2-3: Installing into a Rack

Chassis Installation

Installing the Chassis into a Rack

1. Conﬁ rm that the rails are correctly installed on the rack.

2. Align the bottom of the chassis with the bottom of the rails.

3. Insert the chassis into the rails, keeping the pressure even on both sides, pushing the chassis into the rack until it clicks into the locked position.

4. Secure the chassis handles to the front of the rack.

2-8

FatTwin F617H6-FTL+/FTPTL+ User's Manual

2-6 Checking the Serverboard Setup

After you install the SuperServer F617H6-FTL+/FTPTL+ in the rack, you will need to open the unit to make sure the serverboard is properly installed and all the connections have been made.

Accessing the inside of the System

Before operating the server for the ﬁ rst time, it is important to remove the protective ﬁ lm covering the top of the chassis, in order to allow for proper ventilation and

cooling.

Warning: Except for short periods of time, do NOT operate the server without the cover in place. The chassis cover must be in place to allow proper airﬂ ow and prevent overheating.

Checking the Components and Setup

1. You may have one or two processors already installed into the serverboard. Each processor needs its own heat sink. See Chapter 5 for instructions on processor and heat sink installation.

2. Your SuperServer F617H6-FTL+/FTPTL+ server system may have come with system memory already installed. Make sure all DIMMs are fully seated in their slots. For details on adding system memory, refer to Chapter 5.

3. If desired, you can install add-on cards to the system. See Chapter 5 for details on installing PCI add-on cards.

4. Make sure all power and data cables are properly connected and not blocking the chassis airﬂ ow. Also make sure that no cables are positioned in front of the fans. See Chapter 5 for details on cable connections.

Chapter 2: Server Installation

2-9

2-7 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SATA drives have been properly installed and all connections have been made.

Checking the Drives

1. For the F617H6-FTL+/FTPTL+ server, all hard drives are ﬁ xed on the motherboard tray and can only be retrieved by removing the top cover.

2. Depending upon your system's conﬁ guration, your system may have one or more drives already installed. If you need to install hard drives, please refer to Chapter 6.

Checking the Airﬂ ow

1. Make sure there are no objects to obstruct airﬂ ow in and out of the server. In addition, if you are using a front bezel, make sure the bezel's ﬁ lter is replaced periodically.

2. Do not operate the server without drives or drive trays in the drive bays. Use only recommended server parts.

3. Make sure that no wires or foreign objects obstruct air ﬂ ow through the chassis. Pull all excess cabling out of the airﬂ ow path or use shorter cables. The control panel LEDs inform you of the system status. See “Chapter 3 System Interface” for details on the LEDs and the control panel buttons.

Providing Power

1. Plug the power cord(s) from the power supply unit(s) into a high-quality power strip that offers protection from electrical noise and power surges. It is recommended that you use an uninterruptible power supply (UPS).

2. Depress the power on button on the front of the chassis.

2-10

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Notes

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel to keep you constantly informed of the overall status of the system. F414IS models include four control panels which control each of the systems.

This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.

Figure 3-2: F414IS Node Control Panel

3-3 F414IS Front I/O Control Panel

The F414IS chassis include a power button with a built-in LED and features both a LAN LED and a UID LED on each node's front control panel.

FatTwin F617H6-FTL+/FTPTL+ User's Manual

3-2

• Power: The main power button on each of the four control panels is used to

apply or remove power from the power supply to each of the four systems in the chassis. Turning off system power with this button removes the main power, but keeps standby power supplied to the system. Therefore, you must unplug system before servicing. The poer button has a built-in LED which will turn green when the power is on.

• UID: When used with a UID compatible motherboard, the UID button is used

to turn on or off the blue light function of the LED. This is built into the front side of the UID button and at the rear end of each motherboard node, for those motherboards which support it. Once the blue light is activated, the unit can be easily located in very large racks and server banks.

3-4 Control Panel LEDs

The four control panels are located on the front handle of the F414IS chassis. Each control panel has two additional LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take.

• Information LED: See the fo llowi ng tabl e for the s tatus sh own by this LE D.

Information LED

Status Description

Continously on and red An overheat ocondition has occured. (This may be caused by cable congestion.) Blinking red (1 Hz) Fan failure: check for an inoperative fan. Blinking red (0.25 Hz) Power failure: check for an inoperative power supply. Solid blue Local UID has been activated. Use this function to locate the server in a rack

environment.

Blinking blue (300 msec) Remote UID has been activated. Use this function to locate the server from a

remote location.

Chapter 3: System Interface

3-3

NIC: Indicates network activity on either LAN1 or LAN2 when ﬂ ashing

FatTwin F617H6-FTL+/FTPTL+ User's Manual

3-4

Notes

4-1

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certiﬁ ed technicians should attempt to install or conﬁ gure components.

Read this appendix in its entirety before installing or conﬁ guring components in the Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/ about/policies/safety_information.cfm.

Warning Deﬁ nition

Warning!

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關的翻譯說明內容。

4-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie beﬁ nden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al ﬁ nal de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements ﬁ gurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la ﬁ n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

4-3

Warning Statements for AC Systems

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를 참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's en dient u op de hoogte te zijn van de standaard procedures om ongelukken te voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

4-4

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

設置手順書システムを電源に接続する前に、設置手順書をお読み下さい。

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

4-5

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

警告

此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电流不大于250V,20A。

警告

此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電流不大於250V,20A。

Warnung Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia! Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del ediﬁ cio. Asegúrese de que el dispositivo de protección no sea superior a: 250 V, 20 A.

Attention Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vériﬁ ez que le courant nominal du dispositif de protection n'est pas supérieur à :250 V, 20 A.

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-

250 V, 20 A

4-6

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components.

電源切断の警告システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다.

Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische

installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A.

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-7

Chapter 4: Warning Statements for AC Systems

Warnung Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen.

¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema.

Attention Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou enlever des composants de systéme.

ילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에 반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야 합니다.

Waarschuwing Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

4-8

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Equipment Installation

Warning!

Only trained and qualiﬁ ed personnel should be allowed to install, replace, or service this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualiﬁ ziertem Personal gestattet werden.

¡Advertencia! Solamente el personal caliﬁ cado debe instalar, reemplazar o utilizar este equipo.

Attention Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualiﬁ és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수 있습니다.

4-9

Chapter 4: Warning Statements for AC Systems

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. (This warning does not apply to workstations).

アクセス制限区域

このユニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いてのみ出入りが可能です。

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥匙或其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或其他安全方式才能進入的區域。

Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia! Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una herramienta especial, cerradura con llave u otro medio de seguridad.

Attention Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout autre moyen de sécurité.

Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwaliﬁ ceerd personeel.

4-10

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

4-11

Chapter 4: Warning Statements for AC Systems

Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia! Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing Er is ontplofﬁ ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden.

4-12

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告

此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia! Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las conexiones.

Attention Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées.

דחא קפסמ רתוי םייק םא

!הרהזא

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-13

Chapter 4: Warning Statements for AC Systems

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing.

バックプレーンの電圧システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。修理する際には注意ください。

警告

当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia! Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

4-14

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠

機器の取り付けはその地方および国の電気規格に準拠する必要があります。

警告

设备安装必须符合本地与本国电气法规。

警告

設備安裝必須符合本地與本國電氣法規。

Warnung

Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생 합니다. 서비스 작업 시 주의하십시오.

Waarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het

systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

ירוחאה לנפב חתמ

זא!הרה

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

.הדובעה

Attention Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

4-15

Chapter 4: Warning Statements for AC Systems

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

あります。

警告

本产品的废弃处理应根据所有国家的法律和规章进行。

警告

本產品的廢棄處理應根據所有國家的法律和規章進行。

יצראה למשחה יקוח םואית

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

¡Advertencia! La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales.Attention L'équipement doit être installé conformément aux normes électriques nationales

et locales.

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

4-16

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

Hot Swap Fan Warning

Warning!

The fans might still be turning when you remove the fan assembly from the chassis. Keep ﬁ ngers, screwdrivers, and other objects away from the openings in the fan assembly's housing.

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性があり

ます。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

4-17

Chapter 4: Warning Statements for AC Systems

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬 조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이 가까이 하지 않도록 배치해 주십시오.

当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他物品太靠近风扇

警告

當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他物品太靠近風扇。

Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis

genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador

del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de las aberturas del ventilador

Attention Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez

le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres objets soient éloignés du logement du bloc ventilateur.

4-18

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Power Cable and AC Adapter

Warning!

When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a ﬁ re. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certiﬁ ed cables (that have UL/CSA shown on the code) for any other electrical devices than products designated by Supermicro only.

電源コードとACアダプター製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター

を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあります。 電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

警告

安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告

安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Warnung Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und Material Safety Law verbietet die Verwendung von UL-oder CSA-zertiﬁ zierte Kabel, UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von Supermicro nur bezeichnet gezeigt haben.

Waarschuwing Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het

ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing.

4-19

Chapter 4: Warning Statements for AC Systems

¡Advertencia! Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de Seguridad del Material prohíbe el uso de UL o CSA cables certiﬁ cados que tienen UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos designados por Supermicro solamente.

Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.

L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certiﬁ és qui ont UL ou CSA indiqué sur le code pour tous les autres appareils électriques que les produits désignés par Supermicro seulement.

אתמו םיילמשחמ י

!הרהזא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ

AC רשא

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

ב םיכמסומה םילבכב שמתשהל-

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를 사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이 될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을 위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을 금지합니다.

4-20

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Waarschuwing Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,

stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet verbiedt het gebruik van UL of CSA gecertiﬁ ceerde kabels die UL of CSA die op de code voor andere elektrische apparaten dan de producten die door Supermicro alleen.

Chapter 5: Advanced Motherboard Setup

5-1

Chapter 5

Advanced Motherboard Setup

This chapter covers the steps required to install the X9DRFF-7G+/7TG+ motherboard into the chassis, connect the data and power cables and install add-on cards. All motherboard jumpers and connections are also described. A layout and quick reference chart are included in this chapter for your reference. Remember to completely close the chassis when you have ﬁ nished working with the motherboard to better cool and protect the system.

5-1 Handling the Motherboard

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully (see previous chapter). To prevent the motherboard from bending, keep one hand under the center of the board to support it when handling. The following measures are generally sufﬁ cient to protect your equipment from electric static discharge.

Precautions

• Use a grounded wrist strap designed to prevent Electrostatic Discharge (ESD).

• Touch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid electrical static discharge. When unpacking the board, make sure the person handling it is static protected.

5-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Back Panel I/O Port Locations and Deﬁ nitions

1. Front Panel USB Port 1

2. Front Panel USB Port 2

3. IPMI LAN

4. Gigabit (for F617H6-FTL+) or 10-Gigabit (for F617H6-FTPTL+) LAN 1

5. Gigabit (for F617H6-FTL+) or 10-Gigabit (for F617H6-FTPTL+) LAN 2

6. VGA Port 7 Power Switch/LED

5-2 Connecting Cables

The FatTwin F617H6-FTL+/FTPTL+ server needs to have both power and data cables connected to the X9DRFF-7G+/7TG+ serverboard.

Connecting SATA Power Cables

Various cables used to power each node's SATA drives are connected between the serverboard/power distribution board (PDB) and the drives backplane board.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully routed in preconﬁ gured systems to prevent them from blocking the ﬂ ow of cooling air that moves through the system from front to back. If you need to disconnect any of these cables, you should take care to reroute them as they were originally after reconnecting them (make sure the red wires connect to the pin 1 locations). If you are conﬁ guring the system, keep the airﬂ ow in mind when routing the cables.

5-3 Control Panel Connectors and I/O Ports

The front I/O ports are color coded in conformance with the PC 99 speciﬁ cation. See Figure 5-1 below for the colors and locations of the various I/O ports.

Figure 5-1. Front I/O Ports

21 53 4 6 7

Chapter 5: Advanced Motherboard Setup

5-3

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover, ﬁ rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

WARNING!

Press down on Load Lever labeled 'Open 1st'.

OPEN 1st

WARNING!

5-4 Processor and Heatsink Installation

Warning! When handling the processor package, avoid placing direct pressure on

the label area. Warning! If you buy a CPU separately, make sure that you use an Intel-certiﬁ ed multi-

directional heatsink only. Note: Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the CPU heatsink.

Note: Make sure to install the system board into the chassis before you install the CPU heatsink.

Note: When receiving a server board without a processor pre-installed, make sure that the plastic CPU socket cap is in place and none of the socket pins are bent; otherwise, contact your retailer immediately.

Note: Refer to the Supermicro website for updates on CPU support. Note: When one CPU is installed, be sure to installed on CPU Socket 1 ﬁ rst.

Note: Graphics and drawings shown in this manual are for illustration only. Your

components may or may not look the same as the graphics shown in the manual.

5-4

FatTwin F617H6-FTL+/FTPTL+ User's Manual

2. Press the second load lever labeled 'Close 1st' to release the load plate that covers the CPU socket from its locking position.

OPEN 1st

OPEN

WARNING!

OPEN 1st

WARNING!

Press down on Load the

Lever labeled 'Close 1st'

Pull lever away

from the socket

3. With the lever labeled 'Close 1st' fully retracted, gently push down on the 'Open 1st' lever to open the load plate. Lift the load plate to open it completely.

Gently push down to

pop the load plate open.

OPEN 1st

WARNING!

4. Using your thumb and the index ﬁ nger, remove the 'WARNING' plastic cap from the socket.

WARNING!

Chapter 5: Advanced Motherboard Setup

5-5

5. Use your thumb and index ﬁ nger to hold the CPU on its edges. Align the CPU keys, which are semi-circle cutouts, against the socket keys.

Socket Keys

CPU Keys

6. Once they are aligned, carefully lower the CPU straight down into the socket. (Do not drop the CPU on the socket. Do not move the CPU horizontally or vertically. Do not rub the CPU against the surface or against any pins of the socket to avoid damaging the CPU or the socket.)

Caution: You can only install the CPU inside the socket in one direction. Make sure that it is properly inserted into the CPU socket before closing the load plate. If it doesn't close properly, do not force it as it may damage your CPU. Instead, open the load plate again and double-check that the CPU is aligned properly.

5-6

FatTwin F617H6-FTL+/FTPTL+ User's Manual

7. With the CPU inside the socket, inspect the four corners of the CPU to make sure that the CPU is properly installed.

8. Close the load plate with the CPU inside the socket. Lock the lever labeled 'Close 1st' ﬁ rst, then lock the lever labeled 'Open 1st' second. Use your thumb to gently push the load levers down to the lever locks.

OPEN 1st

OPEN

1st

Push down and lock the level labeled 'Close 1st'.

Gently close

the load plate.

OPEN 1st

OPEN

1st

OPEN 1st

Lever Lock

Push down and

lock the lever

labeled 'Open 1st'

Chapter 5: Advanced Motherboard Setup

5-7

Removing the Heatsink

1. Unplug the power cord from the power supply.

2. Unscrew and remove the heatsink screws in the sequence shown in the picture below.

3. Hold the heatsink and gently wiggle it to loosen it from the CPU. (Do not use excessive force when doing this!)

4. Once the heatsink is loosened, remove it from the CPU.

5. Clean the surface of the CPU and the heatsink to get rid of the old thermal grease. Reapply the proper amount of thermal grease before you re-install the heatsink.

Warning: We do not recommend removing the CPU or the heatsink. If you do need to remove the heatsink, please follow the instructions below to prevent damage to the CPU or other components.

Installing a CPU Heatsink

1. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the retention mechanism.

2. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until just snug (do not over-tighten the screws, which may damage the CPU.)

3. Finish the installation by fully tightening all four screws.

Note: Make sure the heatsink is placed so that the ﬁ ns of the heatsink are in the direction of the airﬂ ow in your system.

5-8

FatTwin F617H6-FTL+/FTPTL+ User's Manual

5-5 Installing Memory

Caution: exercise extreme care when installing or removing DIMM modules to prevent

any possible damage.

Installing Memory

1. Insert the desired number of DIMMs into the memory slots, starting with P1-DIMM #1A. (For best performance, please use the memory modules of the same type and speed in the same bank.)

2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.

3. Align the key of the DIMM module with the receptive point on the memory slot.

4. Align the notches on both ends of the module against the receptive points on the ends of the slot.

5. Use two thumbs together to press the notches on both ends of the module straight down into the slot until the module snaps into place.

6. Press the release tabs to the locking positions to secure the DIMM module into the slot.

Reverse the steps above to remove the DIMM modules from the motherboard. Note: 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules are

supported. It is highly recommended that you remove the power cord from the system before installing or changing memory modules. Please refer to our web site for memory that has been tested on the X9DRFF-7G+/7TG+ serverboard.

To Install: Insert module vertically and press down until it snaps into place. Pay attention to the alignment notch at the bottom.

To Remove: Use your thumbs to gently push the release tabs near both ends of the module. This should release it from the slot.

Top View of DDR3 Slot

Release Tab Release Tab

Note: Notch should align with

the receptive key point on the slot.

Notch

Front View

Figure 5-2. Installing DIMM into Slot

Chapter 5: Advanced Motherboard Setup

5-9

Removing Memory Modules

Press both notches on the ends of the DIMM module to unlock it. Once the DIMM module is loosened, remove it from the memory slot.

Memory Support

The X9DRFF-7G+/7TG+ motherboard supports up to 512 GB of 240-pin Registered (RDIMM)/Load Reduced (LRDIMM) ECC or up to 128 GB of Unbuffered (UDIMM) ECC/Non-ECC DDR3-1600/1333/1066/800 MHz speed 4-channel memory in sixteen (16) DIMM slots.

Note: For the latest CPU/memory updates, please refer to our website at

http://www.supermicro.com/products/motherboard.

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules CPU 1

P1DIMMA1

P1DIMMB1

P1DIMMC1

P1DIMMD1

P1DIMMA2

P1DIMMB2

P1DIMMC2

P1DIMMD2

CPU2

P2DIMME1

P2DIMMF1

P2DIMMG1

P2DIMMH1

P2DIMME2

P2DIMM F2

P2DIMMG2

P2DIMMH2

Processor and Memory Module Population for Optimal Performance

Number of CPUs+DIMMs

CPU and Memory Population Conﬁ guration Table (For memory to work properly, please follow the tables below.)

1 CPU & 2 DIMMs

CPU1 P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

CPU1 P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

1 CPU & 5~8 DIMMs

CPU1 P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1-DIMMA2/ P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots

2 CPUs & 4 DIMMs

CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs & 6 DIMMs

CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

CPU1 + CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1

2 CPUs & 10~16 DIMMs

CPU1/CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots

2 CPUs & 16 DIMMs

CPU1/CPU2 P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/ P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

5-10

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Populating UDIMM (ECC/Non-ECC) Memory Modules

Intel E5-2600(v2) Series Processor UDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

SRx8

Non-ECC

1GB 2GB 4GB NA 1066, 1333,

1600, 1866

NA 1066, 1333,

1600

DRx8

Non-ECC

2GB 4GB 8GB NA 1066, 1333,

1600, 1866

NA 1066, 1333,

1600

SRx16

Non-ECC

512 MB 1GB 2GB NA 1066, 1333,

1600, 1866

NA 1066, 1333,

1600

SRx8

ECC

1GB 2GB 4GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

DRx8

ECC

2GB 4GB 8GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Intel E5-2600(v2) Series Processor UDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5v

SRx8

Non-ECC

1GB 2GB 4GB N/A 1066, 1333,

1600, 1866

N/A 1066, 1333,

1600

DRx8

Non-ECC

2GB 4GB 8GB N/A 1066, 1333,

1600, 1866

N/A 1066, 1333,

1600

SRx16

Non-ECC

512 MB 1GB 2GB N/A 1066, 1333,

1600, 1866

N/A 1066, 1333,

1600

SRx8

ECC

1GB 2GB 4GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

DRx8

ECC

2GB 4GB 8GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Chapter 5: Advanced Motherboard Setup

5-11

Populating UDIMM (ECC/Non-ECC) Memory Modules

Intel E5-2600 Series Processor UDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

SRx8

Non-ECC

1GB 2GB 4GB NA 1066, 1333 NA 1066, 1333

DRx8

Non-ECC

2GB 4GB 8GB NA 1066, 1333 NA 1066, 1333

SRx16

Non-ECC

512 MB 1GB 2GB NA 1066, 1333 NA 1066, 1333

SRx8

ECC

1GB 2GB 4GB 1066, 1333 1066, 1333 1066 1066, 1333

DRx8 ECC

2GB 4GB 8GB 1066, 1333 1066, 1333 1066 1066, 1333

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm..

Intel E5-2600 Series Processor UDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(See the Note below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5v

SRx8

Non-ECC

1GB 2GB 4GB N/A 1066, 1333, N/A 1066, 1333

DRx8

Non-ECC

2GB 4GB 8GB N/A 1066, 1333, N/A 1066, 1333

SRx16

Non-ECC

512 MB 1GB 2GB N/A 1066, 1333 N/A 1066, 1333

SRx8

ECC

1GB 2GB 4GB 1066 1066, 1333, 1066, 1333 1066, 1333

DRx8 ECC

2GB 4GB 8GB 1066 1066, 1333, 1066, 1333 1066, 1333

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm..

5-12

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Populating RDIMM (ECC) Memory Modules

Intel E5-2600(v2) Series Processor RDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(in GB)

(See the Note Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

SRx8 1GB 2GB 4GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

DRx8 2GB 4GB 8GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

SRx4 2GB 4GB 8GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

DRx4 4GB 8GB 16GB 1066, 1333 1066, 1333,

1600, 1866

1066, 1333 1066, 1333,

1600

QRx4 8GB 16GB 32GB 800 800, 1066 800 800 QRx8 4GB 8GB 16GB 800 800, 1066 800 800

Note: For detailed information on memory support and updates, please refer to the SMC Recommended

Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Intel E5-2600(v2) Series Processor RDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(in GB)

(See the Note Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1 DPC 2DPC 3DPC

1.35V 1.5V 1.35V 1.5V 1.35V 1.5v

SRx8 1GB 2GB 4GB 1066,

1333

1066, 1333, 1600, 1866

1066,

1333

1066, 1333,

1600

800 800,

1066

DRx8 2GB 4GB 8GB 1066,

1333

1066, 1333, 1600, 1866

1066,

1333

1066, 1333,

1600

800 800,

1066

SRx4 2GB 4GB 8GB 1066,

1333

1066, 1333, 1600, 1866

1066,

1333

1066, 1333,

1600

800 800,

1066

DRx4 4GB 8GB 16GB 1066,

1333

1066, 1333, 1600, 1866

1066,

1333

1066, 1333,

1600

800 800,

1066

QRx4 8GB 16GB 32GB 800 800,

1066

800 800 N/A N/A

QRx8 4GB 8GB 16GB 800 800,

1066

800 800 N/A N/A

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm.

Chapter 5: Advanced Motherboard Setup

5-13

Populating RDIMM (ECC) Memory Modules

Intel E5-2600 Series Processor RDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(in GB)

(See the Note Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

SRx8

1GB 2GB 4GB

1066, 1333 1066, 1333,

1600

1066, 1333 1066, 1333,

1600

DRx8

2GB 4GB 8GB

1066, 1333 1066, 1333,

1600

1066, 1333 1066, 1333,

1600

SRx4

2GB 4GB 8GB

1066, 1333 1066, 1333,

1600

1066, 1333 1066, 1333,

1600

DRx4

4GB 8GB 16GB

1066, 1333 1066, 1333,

1600

1066, 1333 1066, 1333,

1600

QRx4

8GB 16GB 32GB

800 1066 800 800

QRx8

4GB 8GB 16GB

800 1066 800 800

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm..

Intel E5-2600 Series Processor RDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory Capacity

Per DIMM

(in GB)

(See the Note Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1 DPC 2DPC 3DPC

1.35V 1.5V 1.35V 1.5V 1.35V 1.5v

SRx8

1GB 2GB 4GB

1066,

1333

1066, 1333,

1600

1066,

1333

1066, 1333,

1600

N/A 800,

1066

DRx8

2GB 4GB 8GB

1066,

1333

1066, 1333,

1600

1066,

1333

1066, 1333,

1600

N/A 800,

1066

SRx4

2GB 4GB 8GB

1066,

1333

1066, 1333,

1600

1066,

1333

1066, 1333,

1600

N/A 800,

1066

DRx4

4GB 8GB 16GB

1066,

1333

1066, 1333,

1600

1066,

1333

1066, 1333,

1600

N/A 800,

1066

QRx4

8GB 16GB 32GB

800 1066 800 800 N/A N/A

QRx8

4GB 8GB 16GB

800 1066 800 800 N/A N/A

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/mem.cfm..

5-14

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Populating LRDIMM (ECC) Memory Modules

Intel E5-2600(v2) Series Processor LRDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory

Capacity

Per DIMM

(in GB)

(See the Note

Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

QRx4 (DDP)

16GB 32GB 1066, 1333,

1600

1066, 1333,

1600, 1866

1066, 1333,

1600

1066, 1333,

1600

8Rx4

(QDP)

32GB 64GB 1066 1066 1066 1066

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/

mem.cfm.

Intel E5-2600(v2) Series Processor LRDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory

Capacity

Per DIMM

(in GB)

(See the Note

Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1DPC 2DPC 3DPC

1.35V 1.5V 1.35V 1.5V 1.35V 1.5V

QRx4 (DDP)

16GB 32GB 1066,

1333,

1600

1066, 1333, 1600,

1866

1066, 1333,

1600

1066, 1333,

1600

1066 1066

8Rx4

(QDP)

32GB 64GB 1066 1066 1066 1066 1066 1066

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/

mem.cfm.

Chapter 5: Advanced Motherboard Setup

5-15

Intel E5-2600 Series Processor LRDIMM Memory Support (2 SPC)

Ranks

Per

DIMM

& Data

Width

Memory

Capacity

Per DIMM

(in GB)

(See the Note

Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

2 Slots Per Channel

1DPC 2DPC

1.35V 1.5V 1.35V 1.5V

QRx4 (DDP)

16GB 32GB 1066 1066, 1333 1066 1066, 1333

QRx8 (QDP)

8GB 16GB 1066 1066, 1333 1066 1066, 1333

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/

mem.cfm.

Intel E5-2600 Series Processor LRDIMM Memory Support (3 SPC)

Ranks

Per

DIMM

& Data

Width

Memory

Capacity

Per DIMM

(in GB)

(See the Note

Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

3 Slots Per Channel

1DPC 2DPC 3DPC

1.35V 1.5V 1.35V 1.5V 1.35V 1.5V

QRx4 (DDP)

16GB 32GB 1066 1066,

1333

1066 1066,

1333

1066 1066

QRx8 (QDP)

8GB 16GB 1066 1066 1066 1066 1066 1066

Note: For detailed information on memory support and updates, please refer to the SMC Recommended Memory List posted on our website at

http://www.supermicro.com/support/resources/

mem.cfm.

Other Important Notes and Restrictions

• For the memory modules to work properly, please install DIMM modules of the

same type, same speed and same operating frequency on the motherboard. Mixing of RDIMMs, UDIMMs or LRDIMMs is not allowed. Do not install both ECC and Non-ECC memory modules on the same motherboard.

• Using DDR3 DIMMs with different operating frequencies is not allowed. All

channels in a system will run at the lowest common frequency.

5-16

FatTwin F617H6-FTL+/FTPTL+ User's Manual

5-6 Serverboard Details

Figure 5-3. X9DRFF-7G+/7TG+ Serverboard Layout

LEDS2

HDD_PWR2

T-SGPIO1

T-SGPIO2

6-SGPIO1

6-SGPIO2

VGA1

JPW3

JPW1

FAN8

FAN7

FAN6

FAN5

FAN4

FAN3

FAN2

FAN1

JPI2C1

PWR_SW1

LAN1

I-SATA0

I-SATA1

L-SAS0

L-SAS2

L-SAS4

L-SAS6

L-SAS1

L-SAS3

L-SAS7

L-SAS5

UID_LED1

FAILURE_LED1

USB1

I-SATA2

I-SATA3

I-SATA4

I-SATA5

JIPMB1

JPB1

JPL1

JPME1

JPME2

JWD1

JPG1

JBR1

JP6

JP7

CPLD1

JBT1

HDD_ACT_LED1

JI2C2

JI2C1

JBAT1

CPU2

BIOS

PCH SLOT4 PCIE-E 2.0X4

CPU1 SLOT3 PCI-E 3.0X8

CPU1 SLOT2 PCI-E 3.0X8

CPU1 SLOT1 PCI-E X16 PROPRIETARY SLOT

P2-DIMMH2

P2-DIMMH1

P2-DIMMG2

P2-DIMMG1

P1-DIMMA1

P1-DIMMD1

P1-DIMMA2

P1-DIMMD2

P1-DIMMB1

P2-DIMME1

P1-DIMMB2

P2-DIMME2

P1-DIMMC1

P2-DIMMF1

P1-DIMMC2

P2-DIMMF2

JSD1

SXB1:CPU2 PCI-E X32

PROPRIENTAR SLOT

PS_ON_N

HDD

UID_SW1

USB0

LAN2

IPMI_ LAN

USB2

JPW2

PWR1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

CPU1

Rev. 1.01

X9DRFF-iG+

BMC_HB_LED1

BMC

Intel LAN CTRL

LSI SAS CTRL

Intel PCH

Rear_FAN

IPMI CODE

MAC CODE

SAS CODE

MEGERAC LICENSE

JPS1

Chapter 5: Advanced Motherboard Setup

5-17

Notes:

1. For the latest CPU/Memory updates, please refer to our website at http://

www.supermicro.com/products/motherboard/ for details.

2. Use only the correct type of onboard CMOS battery as speciﬁ ed by the manufacturer. Do not install the onboard battery upside down to avoid possible explosion.

3. The X9DRFF-7TG+ includes 10-GB Ethernet ports.

4. Jumpers not indicated are for test purposes only.

5. All graphics shown in this manual were based upon the latest PCB Revision available at the time of publishing of the manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.

5-18

FatTwin F617H6-FTL+/FTPTL+ User's Manual

X9DRFF-7G+/7TG+ Quick Reference

Jumper Description Default Setting

JBT1 Clear CMOS See Section 5-9 JI2C1/JI2C2 SMB to PCI-E Slots Open (Disabled) JPB1 BMC Enable Pins 1-2 (Enabled) JPG1 VGA Enable Pins 1-2 (Enabled) JPL1 LAN1/LAN2 Enable Pins 1-2 (Enabled) JPS1 SAS Enable Pins 1-2 (Enabled) JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)

Connector Description

FAN1-FAN8, Rear_FAN1 CPU/System/Cooling Fan Headers HDD_PWR1/HDD_PWR2 8-pin Power Supply Connectors for HDD Device Use I-SATA 0/1 SATA 3.0 Connectors 0/1 from Intel AHCI I-SATA 2-7 SATA 2.0 Connectors 2/3/4/5 from Intel AHCI JIPMB1 4-pin External BMC I

C Header (for IPMI Card) JPI2C1 Power Supply SMBbus I2C Header JPW1/JPW2 8-pin Power Connectors JPW3 4-pin Power Connector JSD1 SATA Device Power Connector JTPM1 TPM (Trusted Platform Module)/Port 80 Connector (J) USB2 Internal USB 2 Port L-SAS 0-7 SAS Ports 0-7 from LSI 2308 SAS Controller 6-SGPIO 1/2 Serial Link General Purpose I/O Headers for SAS T-SGPIO 1/2 Serial Link General Purpose I/O Headers for SATA PWR_SW1 Power Switch (Button) UID_SW1 UID (Unit Identiﬁ er) Switch (SW1) USB0/USB1 Front Panel USB 0/ USB1 Ports

LED Description State: Status

BMC_HB_LED1 BMC Heartbeat LED Blinking Green: BMC Normal HDD_ACT LED1 HDD Activity LED Blinking Green: HDD Active

Failure_LED1 Failure LED

Blinking On: Power Failure; Blinking:

Fan Failure LEDS2 SAS Heartbeat LED On (Green): SAS Normal UID_LED1 UID LED On (Blue): Unit Identiﬁ ed

Chapter 5: Advanced Motherboard Setup

5-19

5-7 Connector Deﬁ nitions

ATX Power Connector

Two 8-pin power connectors (JPW1/ JPW2) and a 4-pin power connector (JPW3) are used to provide power to the serverboard. In addition, two 8-pin power connectors (HDD_PWR1/2) are also located onboard to provide power from the serverboard to the HDD backplane for HDD device use. Do not use these connectors for other purposes. All power connectors mentioned above meet the SSI EPS 12V specification. See the tables on the right for pin deﬁ nitions.

12V 8-pin PWR (JPW1/2)

Pin Deﬁ nitions

Pins Deﬁ nition 1- 4 Ground 5-8 +12V

12V 4-pin PWR (JPW3)

Pin Deﬁ nitions

Pins Deﬁ nition 1 Ground 2 Ground 3 5V SB 4 PS_ON_N

HDD PWR Pin Deﬁ nitions

Pins Deﬁ nition 1- 4 Ground 5-6 +12V 7-8 +5V

Video Connection

A Video (VGA) port is located next to the LAN Port 2 on the I/O backplane. Refer to the layout below for the location.

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB0, USB1), located on the I/O front panel, provide front-accessible USB support. In addition, a Type A USB connector (JUSB2), located next to the 4-pin JIPMB1 connector, also provides frontaccessible USB support.

Front Panel USB 0/1

& Type-A USB 2

Pin Deﬁ nitions

Pin# Deﬁ nition 1 +5V 2 PO3 PO+ 4 Ground 5NA

5-20

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Ethernet Ports

Two Ethernet ports (LAN1, LAN2) are located on the I/O front panel. These Ethernet ports support 10G LAN connections on the and X9DRFF-7TG+, or the 1G LAN connections on the and X9DRFF-7G+.

In addition, an IPMI LAN port is also located on the front panel. All these ports accept RJ45 cables. Please refer to the LED Indicator Section for LAN LED information.

Power Button/Unit Identiﬁ er Switch

A Unit Identifier switch (SW1) and a UID LED Indicator are located on the serverboard. In addition, a power button (PWR_SW1) is located next to the UID switch on the front panel. When you press the UID switch, the UID LED Indicator will be turned on. Press the UID switch again to turn off the UID LED. The UID Indicator provides easy identiﬁ cation of a system unit that may be in need of service.

Note: UID can also be triggered via IPMI on the serverboard. For more information on IPMI, please refer to the IPMI User's Guide posted on our website @

http://

www.supermicro.com.

UID Switch (SW1)

Pin Deﬁ nitions

Pin# Deﬁ nition 1 Ground 2 Ground 3 Button In 4 Ground

UID LED (UID_LED1)

Status

Color/State OS Status Blue: On Windows OS Unit Identiﬁ ed Blue:

Blinking

Linux OS Unit Identiﬁ ed

Power Switch

A power switch (PWR_SW1) is located next to the VGA port on the motherboard. Refer to the layout below for the location.

Chapter 5: Advanced Motherboard Setup

5-21

SATA DOM Power Connector

A power connector for SATA DOM (Disk_On_Module) devices is located at JSD1. Connect an appropriate cable here to provide power support for your SATA DOM devices.

DOM PWR (JSD1)

Pin Deﬁ nitions

Pin# Deﬁ nition 1 +5V 2 Ground 3 Ground

T-SGPIO 1/2 & 6-SGPIO 1/2 Headers

Four SGPIO (Serial-Link General Purpose Input/Output) headers (T-SGPIO 1/2 & 6-SGPIO 1/2) are located on the motherboard. These headers support onboard Serial_Link interface connections.

Note: T-SGPIO 1/2 support onboard SA TA connections. 6-SGPIO 1/2 supports the serverboard's SAS connections.

T-SGPIO 1/2

S-SGPIO 1/2

Pin Deﬁ nitions

Pin# Deﬁ nition Pin Deﬁ nition 1NC 2NC 3 Ground 4 Data 5 Load 6 Ground 7 Clock 8 NC

NC indicates no connection.

Fan Headers

This serverboard has eight 4-pin (Fan1~Fan8), and one 3-pin (Rear_Fan1) system/CPU/cooling fan headers on the serverboard. The 4-pin fan headers are backward compatible with traditional 3-pin fans. However, fan speed control is only available on 4-pin fans via IPMI ﬁ rmware management. See the table on the right for pin deﬁ nitions.

Fan Header

(Fan 1~8, Fan 9)

Pin Deﬁ nitions

Pin# Deﬁ nition 1 Ground 2 +12V 3 Tachometer 4 PWR Modulation

(Available for 4-pin fans only)

IPMB

A System Management Bus header for IPMI 2.0 is located at JIPMB1. Connect the appropriate cable here to use the IPMB I2C connection on your system.

IPMB Header

Pin Deﬁ nitions

Pin# Deﬁ nition 1 Data 2 Ground 3 Clock 4 No Connection

5-22

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Power SMB (I

C) Connector

Power System Management Bus (I2C) Connector (JPI2C1) monitors power supply, fan and system temperatures. See the table on the right for pin deﬁ nitions.

PWR SMB (JPI2C1)

Pin Deﬁ nitions

Pin# Deﬁ nition 1 Clock 2 Data 3 PWR Fail 4 Ground 5 +3.3V

Unit Identiﬁ cation Switch/LED

A Unit Identiﬁ er switch (UID) and a UID LED indicator (UID_LED1) are located next to the power switch on the front panel. When the user pushes the UID switch, the UID LED (UID_LED1) will be turned on. Push the UID switch again to turn off the LED indicator. The UID switch provides easy identification of a system unit that may be in need of service. See the tables on the right for more information.

UID Switch (UID) Pin Deﬁ nitions

Pin# Deﬁ nition 1 Ground 2 Ground 3 Button In 4 Ground

TPM Header/Port 80

A Trusted Platform Module/Port 80 header, located at JTPM1, provides TPM support and Port 80 connection. Use this header to enhance system performance and data security. See the table on the right for pin deﬁ nitions.

TPM/Port 80 Header (JTPM1)

Pin Deﬁ nitions

Pin# Deﬁ nition Pin# Deﬁ nition 1 LCLK 2 GND 3 LFRAME# 4 <(KEY)> 5 LRESET# 6 +5V (X) 7 LAD 3 8 LAD 2 9 +3.3V 10 LAD1 11 LAD0 12 GND 13 SMB_CLK4 14 SMB_DAT4 15 +3V_DUAL 16 SERIRQ 17 GND 18 CLKRUN# (X) 19 LPCPD# 20 LDRQ# (X)

Chapter 5: Advanced Motherboard Setup

5-23

5-8 Jumper Settings

Explanation of Jumpers

To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identiﬁ ed with a square solder pad on the printed circuit board. See the diagram at right for an example of jumping pins 1 and 2. Refer to the motherboard layout page for jumper locations.

Note: On two-pin jumpers, "Closed" means the jumper is on and "Open" means the jumper is off the pins.

Connector

Pins

Jumper

Setting

3 2 1

JBT1 contact pads

CMOS Clear

JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins, this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS.

To Clear CMOS

1. First power down the system and unplug the power cord(s). It is also recommended that you remove the onboard battery from the serverboard.

2. With the power disconnected, short the CMOS pads with a metal object such as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note 1. For an ATX power supply, you must completely shut down the system, remove the AC power cord, and then short JBT1 to clear CMOS.

Note 2. Be sure to remove the onboard CMOS Battery before you short JBT1 to clear CMOS.

Note 3. Clearing CMOS will also clear all passwords. Note 4: Do not use the PW_ON connector to clear CMOS.

5-24

FatTwin F617H6-FTL+/FTPTL+ User's Manual

GLAN Enable/Disable

JPL1 enables or disables LAN Port1/ LAN Port2 on the motherboard. See the table on the right for jumper settings. The defau lt sett ing is Ena bled.

Watch Dog Enable/Disable

Watch Dog (JWD1) is a system monitor that will reboot the system when a soft ware applicat ion hangs. Close Pin s 1-2 to reset the system if an application han gs. Close Pins 2-3 t o generate a non- maskable inter rupt signal fo r the applic at i o n th at h an gs . Se e t he table on the ri gh t for jumpe r se tting s. Watc h Dog must also be enabled in the BIOS.

VGA Enable

Jumper JPG1 allows the user to enable onboard VGA support. The default setting is on Pins 1-2 to enable VGA support. See the table on the right for jumper settings.

BMC Enable

Jumper JPB1 allows you to enable the embedded BMC (Baseboard Management) Controller to provide IPMI

2.0 support on the motherboard. See the table on the right for jumper settings.

I2C Bus to PCI-Exp. Slots

Jumpers JI2C1 and JI2C2 allow you to connect the System Management Bus (I2C) to PCI-Express slots. The default setting is Open to disable the connection.

Watch Dog (JWD1)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 Reset (default) Pins 2-3 NMI Open Disabled

VGA Enable (JPG1)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 Enabled (Default) Pins 2-3 Disabled

BMC Enable (JPB1)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 BMC Enable (Default) Pins 2-3 Normal

I2C to PCI-Exp (JI2C1/JI2C2)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 Enabled Pins 2-3 Disabled (Default)

GLAN Enable (JPL1)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 Enabled (default) Pins 2-3 Disabled

Chapter 5: Advanced Motherboard Setup

5-25

SAS Enable

The X9DRFF-7G+/7TG+ serverboards use Jumper JPS1 to enable onboard SAS support to enhance system performance. The default setting is enabled.

SAS Support Enable (JPS1)

Jumper Settings

Jumper Setting Deﬁ nition Pins 1-2 SAS Enabled (Default) Pins 2-3 SAS Disabled

5-9 Onboard Indicators

IPMI Dedicated LAN LEDs

In addition to LAN Ports 1/2, an IPMI Dedicated LAN is also located on the I/O Backplane. The amber LED on the right indicates connection and activity; while t he green LED on the left indicates the speed of the conne c t i o n. S e e t he table s at r i g ht fo r more information.

IPMI LAN

Link/Speed LED (Left)

& Activity LED (Right)

Color Status Deﬁ nition Off Off No Connection Green:

Solid

Link/ Speed (Left)

100 Mb/s

Amber Blinking

Activity (Right)

Active

IPMI LAN

Activity LEDLink LED

GLAN LEDs

There are two LAN ports (LAN1/2) on the motherboard. Each Ethernet LAN port has two LEDs. The Yellow LED on the right indicates connection and activity. The Link LED on the left side may be green, amber or off to indicate the speed of the connection. See the tables at right for more information.

Activity LED

Link Speed

LED

GLAN LED

GLAN Activity Indicator

(Right) LED Settings

Color Status Deﬁ nition Off No Connections Yellow Flashing Active

LAN Connection Speed

Indicator (Left) LED Settings

LED Color Deﬁ nition Off 10 MHz Green 100 MHz Amber 1 GHz

5-26

FatTwin F617H6-FTL+/FTPTL+ User's Manual

BMC Heartbeat (BMC_HB_LED1)

LED Status

Color/State Deﬁ nition Green: Blinking BMC: Normal Steady On BMC Disabled, or

Failed

BMC Heartbeat LED

A BMC Heartbeat LED is located at BMC_HB_LED1 on the motherboard. When this LED indicator is blinking, BMC is normal. See the table at right for more in format ion.

HDD Activity LED

An HDD Activity LED is located at HDD_ACT_LED1 on the motherboard. When the HDD LED is blinking, an HDD device is active. See the table at right for more information.

HDD Activity LED

(HDD_ACT_LED1)

Status

Color or State Deﬁ nition Green: Blinking HDD: Active Off HDD Disabled, or Failed

SAS Heartbeat LED

A SAS Heartbeat LED is located at SAS_HB_LED1 on the motherboard. When LEDS2 is blinking, SAS is working properly.

SAS Heartbeat LED

(SAS_HB_LED1)

Status

Color/State Deﬁ nition Green: Blinking SAS: Normal Off or Red SAS: Disabled or Failed

Failure LED

A BMC Failure LED is located at Failure_LED1 on the motherboard. When th is LED indicato r is on, BMC is not working properly. See the table at right fo r more info rmat ion.

Failure LED

(Failure_LED1)

Status

State Deﬁ nition On BMC: Failed

UID LED

The Unit Identiﬁ er (UID) LED is loc ated at UID_LED1 on the motherboard. When th i s LE D i s o n, t h e u ni t t h at m i gh t be in need of service is identiﬁ ed. See the tab le at right f or more i nform ation.

Rear UID LED

(UID_LED1)

Status

Color/State Deﬁ nition Blue: On Unit Identiﬁ ed

Chapter 5: Advanced Motherboard Setup

5-27

5-10 Serial ATA Connections

SATA/SAS Ports

Eight Serial_ ATA ports are located on the motherboard. I -SATA Ports 0/1 support SATA 3.0. I-SATA Ports 2-8 and S-SAT A 0 support SAT A 2.0. In addition, eight SAS p o rts ( L-SAS 0-7), supp o rted by the LSI SAS 2208 Controller are also located on the serverboards. See the table o n the ri ght for p in deﬁ nitions.

Note: For more information on SATA HostRAID conﬁ guration, please refer to the Intel SATA and LSI SAS HostRAID User's Guides posted on our Website @

http://www.supermicro.com..

5-28

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Figure 5-4. Driver/Tool Installation Display Screen

5-11 Installing Drivers

The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.

supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the ftp site, go into the CDR_Images directory and locate the ISO ﬁ le for your motherboard. Download this ﬁ le to create a CD/DVD of the drivers and utilities it contains. (You may also use a utility to extract the ISO ﬁ le if preferred.)

Another option is to go to the Supermicro Website at

http://www.supermicro.com/ products/. Find the product page for your motherboard here, where you may

download individual drivers and utilities. After creating a CD/DVD with the ISO ﬁ les, insert the disk into the CD/DVD drive

on your system and the display shown in Figure 5-4 should appear.

Chapter 5: Advanced Motherboard Setup

5-29

Note: Click the icons showing a hand writing on paper to view the readme ﬁ les for each item. Click the computer icons to the right of these items to install each item (from top to the bottom) one at a time. After installing each item, you must re-boot the system before moving on to the next item on the list. The bottom icon with a CD on it allows you to view the entire contents.

SuperDoctor III

The SuperDoctor® III program is a web-based management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The SuperDoctor III program allows you to monitor the environment and operations of your system. SuperDoctor III displays crucial system information such as CPU temperature, system voltages and fan status. See the ﬁ gures below for examples of the SuperDoctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN. Note: When SuperDoctor III is ﬁ rst installed, it adopts the temperature threshold

settings that have been set in BIOS. Any subsequent changes to these thresholds must be made within SuperDoctor III, as the SuperDoctor III settings override the BIOS settings. To set the BIOS temperature threshold settings again, you would ﬁ rst need to uninstall SuperDoctor III.

Figure 5-7. Supero Doctor III Interface Display Screen (Health Information)

5-30

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Note: The SuperDoctor III program and User’s Manual can be downloaded from the Supermicro web site at http://www.supermicro.com/products/accessories/software/

SuperDoctorIII.cfm. For Linux, we recommend that you use the SuperoDoctor II

application instead.

Figure 5-8. Supero Doctor III Interface Display Screen (Remote Control)

Chapter 5: Advanced Motherboard Setup

5-31

5-12 Serverboard Battery

Caution: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarites (see Figure 5-7). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries according to the manufacturer's instructions.

Figure 5-7. Installing the Onboard Battery

LITHIUM BATTERY

BATTERY HOLDER

Please handle used batteries carefully. Do not damage the battery in any way; a damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landﬁ ll. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly.

5-32

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Notes

Chapter 6: Advanced Chassis Setup

6-1

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform maintenance on the F414IS-R1K62B chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If some steps are unnecessary, skip ahead to the step that follows.

Tools Required: The only tool you will need to install components and perform maintenance is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electrostatic discharge (ESD) can damage electronic com ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully. The following measures are generally sufﬁ cient to protect your equipment from ESD damage.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the serverboard.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When unpacking the board, make sure the person handling it is static protected.

6-2

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Figure 6-1. Front and Rear Chassis Views

6-2 Control Panel

The control panel for each node is located on the front of the chassis. The LEDs inform you of system status.

See Chapter 3 for details on the LEDs and the control panel buttons.

Ethernet Ports

USB Ports VGA Port

IPMI LAN Port

Control Panel

Power Supply Chassis Fan

Chapter 6: Advanced Chassis Setup

6-3

6-3 Removing the Power Cord

Before performing any setup or maintenance on the chassis, use the following procedure to ensure that power has been removed disconnected from the system.

Removing the Power Cord

1. Use the operating system to power down the system, following the on-screen prompts.

2. After the system has completely shut-down, carefully grasp the head of the power cord and gently pull it out of the back of the power supply.

3. If your system has dual redundant power supplies, remove the cords from both power supplies.

4. Disconnect the cord from the power strip or wall outlet.

6-4 Removing Nodes from the Chassis

Each of the four individual motherboard nodes may be removed from the chassis. Note that any time a node is removed from the chassis, the hard drives located in the node twill shut-down.

Removing a Motherboard Node

1. Power down the system and remove the power cords from the rear of the node as described on the previous page.

2. Grasp the node by the handles on either side of the front of the node.

3. Carefully pull the node forward and out of the chassis.

6-4

FatTwin F617H6-FTL+/FTPTL+ User's Manual

6-5 Removing the Node Cover

Each node has a removable cover which will permit access to the nodes components.

Removing the Node Cover

1. Remove the power cord from the rear of the node as described in Section 6-3 and remove the node from the chassis as described in Section 6-4. Place the node on a ﬂ at, stable surface.

2. Remove the six screws securing the cover to the node, as illustrated above.

3. Lift the cover up and off the node.

Figure 6-2: Removing the Node Cover

Chapter 6: Advanced Chassis Setup

6-5

6-6 Installing and Removing Hard Drives

The F414IS chassis contains individual motherboards in separate 1U nodes. Each motherboard node controls the hard drives contained within that node. Note that if a node is pulled out of the chassis, the hard drives associated with that node will power down as well. Refer to the charts below and on the following pages for your speciﬁ c chassis conﬁ guration. These instructions apply to ﬁ xed 3.5" hard drives.

Only enterprise level hard drives are recommended for use in Supermicro chassis.

F414IS-R1K62B Chassis Nodes and Their Hard Drives

Node 4

Controls twelve (12) 3.5" HDDs, optional two (2) 2.5" HDDs, D1-D15

Node 3

Controls twelve (12) 3.5" HDDs, optional two (2) 2.5" HDDs, C1-C15

Node 2

Controls twelve (12) 3.5" HDDs, optional two (2) 2.5" HDDs, B1-B15

Node 1

Controls twelve (12) 3.5" HDDs, optional two (2) 2.5" HDDs, A1-A15

Figure 6-3: Chassis Nodes and their Corresponding Motherboards

(Your chassis and drives may differ from those shown in this illustration)

Node 2

Node 4

Node 1

Node 3

6-6

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Figure 6-4: Installing 3.5" Hard Drives in the Node

Replacing Fixed 3.5" Hard Drives

Replacing a Fixed 3.5" Hard Drive

1. Power down the node with the operating system and remove the cord from the rear of the power supply as described in Section 6-3. Remove the node from the chassis as described in Section 6-4. Remove the node cover as described in Section 6-5.

2. Remove the screw securing the hard drive tray to the ﬂ oor of the node and set it aside for later use.

3. Press the latch on the HDD tray.

4. Shift the tray toward the dirction of the latch.

5. Lift the hard drive up and out of the node.

6. Remove the four screws securing the hard drive to the hard drive tray and set them aside for later use.

7. Remove the hard drive from the tray and replace it with a new hard drive.

8. Align the mounting holes in the hard drive with those in the the hard drive tray and secure the hard drive using the screws previously set aside.

9. Place the hard drive and tray in the node and secure the tray to the ﬂ oor of the node with the mounting screw previously set aside.

Caution: Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers. For information on recommended HDDs, visit the Supermicro Web site at

http://www.supermicro.com/products/nfo/ﬁ les/

storage/SAS-CompList.pdf

3.5" HDD

Chapter 6: Advanced Chassis Setup

6-7

6-7 Node Conﬁ guration

The four F414IS chassis nodes are conﬁ gured as illustrated above. In addition to the node components shown, there are eight exhaust fans and two power supplies located in the rear of the chassis body.

Figure 6-5: Conﬁ guration of the Node

Four 3.5" HDDs

Seven 3.5" HDDs

Backplane

Located

Below HDDs

Two Low-Proﬁ le

PCIE Slots

HDD Backplane Board Located Below HDDs

One 3.5" HDD

MB Location

Power Adapter Board

6-8

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Figure 6-6: Removing the Backplane

(Note: HDD trays shown empty for clarity, most will have HDDs installed)

6-8 Removing and Installing the Backplane

The F414IS backplane is located under the hard drives on the front left side of each node as shown in Figure 6-5. Although backplane failure rarely occurs, in the event of a backplane failure, follow the instructions below.

Removing the Backplane

Removing the Backplane from the Node

2. Remove the screws securing the 3.5" hard drive trays and release the trays as described on page 6-6.

3. Remove the screws securing the protection cover and set them aside for later use.

4. Lift the protection cover with the attached backplane, up and out of the node.

Chapter 6: Advanced Chassis Setup

6-9

Figure 6-7: Removing the Backplane from the Protection Cover

5. Remove the three screws securing the backplane to the protection cover.

Figure 6-8: Installing the Backplane

(Note: HDD trays shown empty for clarity, most will have HDDs installed)

6. Install a replacement backplane onto the protection cover and secure with the screws previously set aside.

7. Place the protection cover in the node and secure it to the ﬂ oor of the node with the screws previously set aside.

8. Secure the ﬁ xed 3.5" hard drives and their trays over the protection cover as described on page 5-5.

9. Replace the node cover, return the node to its bay in the chassis, plug the power cord into the rear of the power supply and power up the node.

6-10

FatTwin F617H6-FTL+/FTPTL+ User's Manual

6-9 Power Adapter Board Replacement

Each of the nodes includes a power adapter board, which connects it to the chassis. In the unlikely event of a failure of the power adapter board, replacement is simple and requires only a Phillips head screwdriver.

Changing the Power Adapter Board

2. Remove the screws securing the power adapter board to the ﬂ oor of the node and set them aside for later use.

3. Lift the power adapter board up and out of the node.

4. Place the power adapter board into the same position on the ﬂ oor of the node, aligning the mounting holes of the board with those in the node. Secure the board with the screws previously set aside. Do not exceed eight pound of torque when tightening the power distributor board.

5. Place the cover back on the node, return the node to the chassis, plug the power cord into the rear of the power supply and power up the node.

Figure 6-9: Removing the Power Adapter Board

Chapter 6: Advanced Chassis Setup

6-11

6-10 Installing the Motherboard

Compatible Motherboards

For the most up-to-date information on compatible motherboards and other parts, visit the Supermicro Web site at www.supermicro.com.

Permanent and Optional Standoffs

Standoffs prevent short circuits by creating space between the motherboard and the ﬂ oor of the node. The F414IS chassis includes permanent standoffs in locations used by most motherboards. These standoffs use the rounded Phillips head screws included in the F414IS accessories packaging.

Some motherboards require additional screws for heatsinks, general components and/or non-standard security. Optional standoffs are used for these motherboards.

To use an optional standoff, compare the mounting holes in the motherboard with those in the ﬂ oor of the motherboard node. Then place a screw through the bottom the node and secure the screw with a hexagonal nut (rounded side up).

Depending upon the conﬁ guration of the motherboard being used, it is also possible that some of the optional standoffs which are pre-installed in the chassis, may need to be removed. Add or remove standoffs as needed.

Figure 6-10: Installing the Motherboard in the Node

6-12

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Installing the Motherboard

1. Review the documentation that came with your motherboard. Become familiar with component placement, requirements, cautions, and cable connections.

2. Compare the mounting holes in the node with those in the motherboard. Add or remove standoffs as needed.

3. Secure the motherboard to the ﬂ oor of the node tray using the rounded, Phillips head screws included for this purpose. Do not exceed eight pounds of torque when tightening down the motherboard.

4. Refer to the next section of this for instructions on installing the expansion card

5. After installing the expansion card, ecure the CPU(s), heatsinks, and other components to the motherboard as described in the motherboard documentation.

6. Connect the cables between the motherboard, backplane, front panel, and power supply, as needed.

7. Return the node ot the chassis and power up the node.

Chapter 6: Advanced Chassis Setup

6-13

6-11 Installing Expansion Cards

PCIE Slot Setup

The nodes of some F414IS chassis models support two low-proﬁ le expansion cards. To install the low-proﬁ le expansion cards follow the instructions on the following pages.

Figure 6-11: PCIE Slot Shield Conﬁ guration

Low-Proﬁ le PCIE Slot Cover

6-14

FatTwin F617H6-FTL+/FTPTL+ User's Manual

Installing a Low-Proﬁ le Expansion Card

The F414IS chassis supports two low-proﬁ le expansion cards in each of the four nodes for a total of eight expansion cards in the chassis, Each expansion card connects to the motherboard with a riser card.

Installing a Low-Proﬁ le Expansion Card into a Node

2. Remove the three screws securing the riser card bracket to the node and set them aside for later use.

3. Remove the mounting screw which secures the PCIE slot cover in the riser card bracket and set this aside for later use.

4. Remove the PCIE slot cover by sliding it sideways and out of the PCIE slot and set this screw aside for later use.

5. Lift the riser card bracket up and out of the chassis.

6. Assemble the riser card as illustrated below, by simultaneously connecting the expansion card to the riser card, while sliding the PCIE slot cover into the PCIE slot.

7. Secure the PCIE slot cover into the PCIE slot with the screw previously set aside.

8. Insert the riser card into the motherboard and secure the riser card bracket to the node with the screws previously set aside.

9. Place the node cover on top of the node and secure it with the eight screws previously used for this purpose.

10. Return the node to the chassis, plug the power cord into the rear of the power supply and power up the node.

Supermicro FatTwin F617H6-FTL+, FatTwin F617H6-FTPTL+, FatTwin F627G2-FTPT+, FatTwin F627G2-FT+, FatTwin F627G2-F73+ User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual