Supermicro CSE-M35TQB operation manual

SUPER

®

M35TQ

Mobile Rack

USER'S GUIDE

Rev. 1.0c

M35TQ Mobile Rack User's Guide

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0c
Release Date: August 5, 2010

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2010 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

ii

Safety Information and Technical Specifi cations

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Product Features ........................................................................................... 1-1

Operating Systems Supported ........................................................................ 1-1

System Monitoring .......................................................................................... 1-2

1-3 An Important Note to the User ........................................................................1-2

1-4 Contacting Supermicro ....................................................................................1-3

1-5 Returning Merchandise for Service.................................................................1-4

Chapter 2 SAS-M35TQ Backplane Specifi cations

2-1 ESD Safety Guidelines ................................................................................... 2-1

2-2 General Safety Guidelines ..............................................................................2-1

2-3 Introduction to the SAS-M35TQ Backplane .................................................... 2-2

Chapter 3 Backplane Connectors, Jumpers and LEDs

3-1 Front Connectors and Jumpers ...................................................................... 3-1

3-2 Front Connectors and Pin Defi nitions ............................................................. 3-2

3-3 Front Jumper Locations and Pin Defi nitions ...................................................3-4

Explanation of Jumpers ..................................................................................3-4

Buzzer and Chip Reset Jumper Settings ........................................................3-5

Fan Jumper Settings ....................................................................................... 3-6

2

I

C and SGPIO Modes and Jumper Settings .................................................3-7

3-4 Rear Connectors and LED Indicators ............................................................. 3-8

Chapter 4 Mobile Rack Installation Procedures

4-1 Tools Required ................................................................................................4-1

4-2 Important Safety Guidelines ............................................................................4-1

4-3 Installation Procedures ....................................................................................4-2

Installing Hard Drives into the Mobile Rack ....................................................4-2

Additional Optional Installation Information.....................................................4-8

iii

Safety Information and Technical Specifi cations

Chapter 1

Introduction

1-1 Overview

This manual is written for system integrators, PC technicians and knowledgeable PC
users who intend to integrate Supermicro's intelligent, highly expandable and cost­effective mobile rack solutions into their systems. It provides the user with detailed
information for the installation and use of the M35TQ mobile rack.

The Supermicro M35TQ mobile rack supports SAS or SATA hard drives, and can
accomodate up to fi ve 3.5" hard drives or three 5.25" hard drives. The M35TQ
showcases today's most advanced technological innovations in modular connectiv­ity and data transferability, laying the foundation for reliable, effective and scalable
solutions for tomorrow's data communications industry.

1-2 Product Features

The M35TQ mobile rack includes the following features:

Supports SAS or SATA

•

Supports fi ve 3.5" hot-swappable HDDs or three 5.25" HDDs•

Operating Systems Supported

For the most up-to-date information visit the Supermicro Web site at www.super­micro.com

Windows 2000, Windows XP, and Windows 2003

•

Linux: Red Hat and SuSE •

1-1

M35TQ Mobile Rack User's Guide

System Monitoring

Fan failure LED•

Overheat LED indicatior•

Drive activity indicatior•

1-3 An Important Note to the User

The pictures or graphics shown in this User's Guide were based upon the latest
PCB revision available at the time of the publishing of this manual. The M35TQ
mobile rack you've received may or may not look exactly the same as the graphics
shown in this manual.

1-2

Safety Information and Technical Specifi cations

1-4 Contacting Supermicro

Headquarters
Address: Super Micro Computer, Inc.

980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe
Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c
Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.

Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone]

1-3

M35TQ Mobile Rack User's Guide

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be­fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning
to the manufacturer, the RMA number should be prominently displayed on the
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service
is complete.

For faster service, RMA authorizations may be requested online (http://www.super­micro.com/support/rma/).

Whenever possible, repack the mobile rack in the original Supermicro carton, using
the original packaging material. If these are no longer available, be sure to pack the
mobile rack securely, using packaging material to surround the mobile rack so that
it does not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in­curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.

During the warranty period, contact your distributor fi rst for any product problems.

1-4

Safety Information and Technical Specifi cations

Chapter 2

SAS-M35TQ Backplane Specifi cations

To avoid personal injury and property damage, carefully follow all the safety steps
listed below when accessing your system or handling the components.

2-1 ESD Safety Guidelines

Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent dam­age to your system, it is important to handle it very carefully . The following measures
are generally suffi cient to protect your equipment from ESD.

Use a grounded wrist strap designed to prevent static discharge.

•

Touch a grounded metal object before removing a component from the antistatic •
bag.

Handle the backplane by its edges only; do not touch its components, peripheral

•

chips, memory modules or gold contacts.

When handling chips or modules, avoid touching their pins.

•

Put the backplane and peripherals back into their antistatic bags when not in •
use.

2-2 General Safety Guidelines

Always disconnect power cables before installing or removing any components •
from the computer, including the mobile rack.

Disconnect the power cable before installing or removing any cables from the

•

mobile rack.

Make sure that the mobile rack is securely and properly installed on the moth-

•

erboard to prevent damage to the system due to power shortage.

2-1

M35TQ Mobile Rack User's Guide

2-3 Introduction to the SAS-M35TQ Backplane

The M35TQ mobile rack contains a SAS-M35TQ backplane. The SAS-M35TQ
backplane has been designed to utilize the most up-to-date technology available,
providing your system with reliable, high-quality performance.

This manual refl ects SAS-M35T Revision 1.01, the most current release available at
the time of publication. Always refer to the Supermicro W eb site at www.supermicro.
com for the latest updates, compatible parts and supported confi gurations.

2-2