AOC-STG-i4T
User's Guide
Revision 1.0
The information in this User's Guide has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this user's guide, or to
notify any person or organization of the updates. Please Note: For the most up-to-date version
of this user's guide, please see our Website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this user's guide at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
User's Guide Revision 1.0
Release Date: August 10, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
About this User's Guide
This user's guide is written for system integrators, IT technicians and
knowledgeable end users. It provides information for the installation and use of the
AOC-STG-i4T add-on card.
About this Add-on Card
The AOC-STG-i4T is the most energy-efcient and cost-effective 4-port 10GBase-
T adapter solution for data centers in today's market. Based on the Intel® XL710
and X557 chipsets with virtualization features such as VxLAN and NVGRE, the
AOC-STG-i4T addresses the demands of bandwidth-intensive applications at a
fraction of the cost of a traditional 10GbE adapter by utilizing RJ-45 connections
for a longer cabling distance. The AOC-STG-i4T 10GbE adapter is truly a best-in-
class solution for advanced data centers. This add-on card is intended to be used
with Supermicro's servers or motherboards as an integrated solution package. For
more information regarding product support or updates, please refer to our website
at http://www.supermicro.com/products/nfo/networking.cfm#adapter.
Preface
An Important Note to the User
All images and layouts shown in this user's guide are based upon the latest PCB
Revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this user's guide.
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before
any warranty service will be rendered. You can obtain service by calling your ven-
dor for a Returned Merchandise Authorization (RMA) number. When returning the
motherboard to the manufacturer, the RMA number should be prominently displayed
on the outside of the shipping carton, and the shipping package is mailed prepaid
or hand-carried. Shipping and handling charges will be applied for all orders that
must be mailed when service is complete. For faster service, you can also request
a RMA authorization online (http://www.supermicro.com/RmaForm/).
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alternation, misuse, abuse or improper
maintenance of products.
iii
AOC-STG-i4T Add-on Card User's Guide
C onf ide nt ia l
N am i ng C onvent i on f or N et w or ki ng A dapt er s
C onf ide nt ia l
7 / 2 0 1 6
S upe rm i c ro N e t w or k i ng A da pt e r L i s t
During the warranty period, contact your distributor rst for any product problems.
Conventions Used in the User's Guide
Pay special attention to the following symbols for proper system installation and to
prevent damage to the system or injury to yourself:
Warning: Important information given to ensure proper system installation
or to prevent damage to the components or injury to yourself.
Note: Additional information given to differentiate between various models
or provides information for correct system setup.
Naming Convention
A O C – S T G N – i 2 S
1 – 2 3 4 – 5 6 7
Character Representation Options
1st Product Family AOC: Add On Card
2nd Form Factor S: Standard, P: Proprietary, C: MicroLP, U: UIO
3rd Product Type/Speed G: GbE (1Gb/s), TG: 10GbE (10Gb/s), 40G: 40GbE
4th Chipset Model (Optional) N: Niantec (82599), P: Powerville (i350),
5th Chipset Manufacturer i: Intel, m: Mellanox, b: Broadcom
6th Number of Ports 1: 1 port, 2: 2 ports, 4: 4 ports
7th Connector Type (Opt ional) S: SFP+, T: 10GBase-T, Q: QSFP+
(40Gb/s), IBF: FDR IB (56Gb/s), IBQ: QDR IB (40Gb/s)
S: Sageville (X550)
SMC Networking Add-on Cards
Model T ype Form Factor Controller Connection
AOC-MGP-i2 GbE SIOM Intel® i350 AM2 2 RJ45 (1Gb/port) 3.622" (92mm) x 3.428" (87.08mm) 3.7
AOC-MGP-i4 GbE SIOM Intel® i350 AM4 4 RJ45 (1Gb/port) 3.622" (92mm) x 3.428" (87.08mm) 4.4
AOC-MTGN-i2S 10GbE SIOM Intel® 82599ES 2 SFP+ (10Gb/port ) 3.622" (92mm) x 3.428" (87.08mm) 7.2
AOC-MTG-i4S 10GbE SIOM Intel® XL710-BM1 4 SFP+ (10Gb/port ) 3.622" (92mm) x 3.428" (87.08mm) 7
AOC-MTG-i2T 10GbE SIOM Intel® X550-AT2 2 RJ45 (10GBase-T) 3.622" (92mm) x 3.428" (87.08mm ) 13
AOC-MTG-i4T 10GbE SIOM 2x Intel® X550-AT2 4 RJ45 (10GBase-T) 3.622" (92mm) x 3.428" (87.08mm ) 26
AOC-MHIBF-m1Q2G
AOC-MHIBF-m2Q2G
AOC-MH25G-b2S2G
AOC-MH25G-m2S2T 25GbE SIOM
AOC-MHFI-i1C
FRD IB
GbE
FRD IB
GbE
25GbE
GbE
Omni-
Path
SIOM
SIOM
SIOM
SIOM
Mellanox® ConnectX-3 Pro
Intel® i350
Mellanox® ConnectX-3 Pro
Intel® i350
Broadcom® BCM57414
Intel® i350
Mellanox® ConnectX-4 Lx EN
Intel® X550-AT2
Intel® OP HFI ASIC
(Wolf River WFR-B)
1 QSFP (56Gb/port)
2 RJ45 (1Gb/port)
2 QSFP (56Gb/port)
2 RJ45 (1Gb/port)
2 SFP28 (25Gb/port)
2 RJ45 (1Gb/port)
2 SFP28 (25Gb/port)
2 RJ45 (10GBase-T)
1 QSFP28 (100Gb/port) 3.622" (92mm) x 3.428" (87.08mm) 15
iv
Dimension
(w/o Brackets) (L x H)
3.622" (92mm) x 3.428" (87.08mm) 9
3.622" (92mm) x 3.428" (87.08mm) 11
3.622" (92mm) x 3.428" (87.08mm) 9
3.622" (92mm) x 3.428" (87.08mm) 25
Power
(W)
C onf ide nt ia l
7 / 2 0 1 6
S upe rm i c ro N e t w or k i ng A da pt e r L i s t
C onf ide nt ia l
7 / 2 0 1 6
S upe rm i c ro N e t w or k i ng A da pt e r L i s t
M ode l T yp e For m Fa c t or I n t er f ace C ont r ol l e r C onne c t i on
D i m e ns i on
( w / o B r acket s) ( L x H )
P o w er
(W )
Preface
Model Type Form Factor Interface Controller Connection
AOC-SGP-i2 GbE Standard LP PCI-E x4 Intel® i350 AM2 2 RJ45 (1Gb/port) 3.9” (99mm) x 2.73” (69mm) 3.5
AOC-SGP-i4 GbE Standard LP PCI-E x4 Intel® i350 AM4 4 RJ45 (1Gb/port) 3.9” (99mm) x 2.73” (69mm) 5
AOC-STG-i2T 10GbE Standard LP PCI-E x8 Intel® X540-AT2 2 RJ45 (10GBase-T) 5.9” (150m m) x 2.73” (69mm) 13
AOC-STGS-i1T 10GbE Standar d LP PCI-E x4 Intel® X550-AT 1 RJ45 (10GBase-T) 5.9” (150mm) x 2.73” (69mm) 9
AOC-STGS-i2T 10GbE Standar d LP PCI-E x4 Intel® X550-AT2 2 RJ45 (10GBase-T) 5.9” (150mm) x 2.73” (69mm) 11
AOC-STG-i4T 10GbE Standard LP PCI-E x8 Intel® XL710-BM1 4 RJ45 (10GBase-T) 5.9” (14.99cm) x 2.73”(6.9cm) 15.5
AOC-STGN-i1S 10GbE Standard LP PCI-E x8 Intel® 82598EN 1 SFP+ (10Gb/port) 4.0” (102mm) x 2.73” (69mm) 10
AOC-STGN-i2S 10GbE Standard LP PCI-E x8 Intel® 82599ES 2 SFP+ (10Gb/port) 4.0” (102mm) x 2.73” (69mm) 11.2
AOC-STGF-i2S 10GbE Standar d LP PCI-E x8 Intel® X710-BM2 2 SFP+ (10Gb/port) TBD TBD
AOC-STG-b4S 10GbE S tandard LP PCI-E x8 Broadcom® BCM57840S 4 SFP+ (10Gb/port) 5.4” (137mm) x 2.73” (69mm) 14
AOC-STG-i4S 10GbE Standard LP PCI-E x8 Intel® XL710-BM1 4 SFP+ (10Gb/p ort) 5.9” (150mm ) x 2.73” (69mm) 8
AOC-S40G-i4S 10GbE Standard LP PCI-E x8 Intel® XL710-BM1
AOC-S25G-b2S 25GbE Standard LP PCI-E x8 Broadcom® BCM57414 2 SFP28 (25Gb/port) 5.6" (142mm) x 2.713“ (69mm ) 7
AOC-S25G-m2S 25GbE St andard LP PCI-E x8 Mellanox® CX-4 LX 2 SFP28 (25Gb/port) TBD TBD
AOC-S40G-i1Q 40GbE Standar d LP PCI-E x8 Intel® XL710-BM1 1 QSFP+ (40Gb/port) 5.9” (150mm) x 2.73” (69mm) 6.5
AOC-S40G-i2Q 40GbE Standar d LP PCI-E x8 Intel® XL710-BM2 2 QSFP+ (40Gb/port) 5.9” (150mm) x 2.73” (69mm) 7
AOC-S100G-m2C 100GbE Standard LP PCI-E x16 Mellanox® CX-4 EN 2 QSFP28 (100Gb/por t) TBD TBD
AOC-PTG-i1S 10GbE Proprietary PCI-E x8 Intel® 82599EN 1 SFP+ (10G b/port) 10.04” (255mm) x .78” (20mm) 7.5
AOC-UG-i4 GbE UIO FH PCI-E x8 Intel® 82571EB 4 RJ45 (1Gb/port) 6.6” (167mm) x 3.9” (98mm) 10
AOC-CGP-i2 GbE M icroLP PCI-E x4 Intel® i350 AM2 2 RJ45 (1Gb/port) 4.45” (113mm) x 1.54” (39mm) 4
AOC-CG-i2 GbE MicroLP PCI-E x4 Intel® 82580 2 RJ45 (1Gb/port) 4.45” (113mm) x 1.3” (34mm) 4
AOC-CIBF-m1 FDR IB MicroLP PCI-E x8 Mellanox® ConnectX-3 1 QSFP (56Gb/port) 4.85" (123mm) x 1.54" (39mm) 7
AOC-CTG-i1S 10GbE MicroLP PCI-E x8 Intel® 82599EN 1 SFP+ (10Gb/port) 4.85" (123mm) x 1.54" (39mm) 10
AOC-CTG-i2S 10GbE MicroLP PCI-E x8 Intel® 82599ES 2 SFP+ (10Gb/port ) 4.85" (123mm) x 1.54" (39mm) 11
AOC-CTG-i2T 10GbE MicroLP PCI-E x8 Intel® X540-AT2 2 RJ45 (10GBase-T) 4.8” (123mm) x 2.75” (77mm) 13
AOC-CTGS-i2T 10GbE Micr oLP PCI-E x4 Intel® X550-AT2 2 RJ45 (10GBase-T) 4.45” (113mm) x 1.54” (39mm) 12
AOC-C25G-m2S
25GbE MicroLP PCI-E x8 Mellanox® CX-4 Lx EN 2 SFP28 (28Gb/por t) 4.45” (113mm) x 1.54” (39mm) 9
1 QSFP+ w/ breakout
cable to 4 x 10GbE
Dimension
(w/o Brackets) (L x H)
5.9” (150mm) x 2.73” (69mm) TBD
Power
(W)
v
AOC-STG-i4T Add-on Card User's Guide
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Email: support@supermicro.com.tw
Website: www.supermicro.com.tw
vi
Preface
Table of Contents
Preface
Chapter 1 Overview
1-1 Overview ......................................................................................................... 1-1
1-2 Product Highlights ........................................................................................... 1-1
1-3 Technical Specications .................................................................................. 1-2
General ............................................................................................................ 1-2
I/O Features .................................................................................................... 1-2
Virtualization Features..................................................................................... 1-2
Storage Interface Features ............................................................................. 1-3
Management Features .................................................................................... 1-3
Advanced Software Features .......................................................................... 1-3
OS Support ..................................................................................................... 1-3
Power Consumption ........................................................................................ 1-4
Operating Conditions ...................................................................................... 1-4
Physical Dimensions ....................................................................................... 1-4
Supported Platforms ....................................................................................... 1-4
1-4 Compliance/Operating Environment ............................................................... 1-5
Chapter 2 Hardware Components
2-1 Add-On Card Image and Layout ..................................................................... 2-1
2-2 Major Components .......................................................................................... 2-2
2-3 LAN Ports and LAN LED indicators ................................................................ 2-3
2-4 NC-SI Header & PCI-E 3.0 x8 Connector ...................................................... 2-4
2-5 Overheat LED & DIP Switch ........................................................................... 2-5
Chapter 3 Installation
3-1 Static-Sensitive Devices .................................................................................. 3-1
3-2 Before Installation ........................................................................................... 3-2
3-3 Installing the Add-on Card .............................................................................. 3-2
3-4 Installing Drivers on Windows ......................................................................... 3-3
3-5 Installing Drivers on Linux ............................................................................... 3-3
3-6 Installing Drivers on FreeBSD ........................................................................ 3-5
3-7 Asset Management Features .......................................................................... 3-8
vii
AOC-STG-i4T Add-on Card User's Guide
Notes
viii
Chapter 1: Overview
Chapter 1
Overview
1-1 Overview
Congratulations on purchasing your add-on card from an acknowledged leader in
the industry. Supermicro products are designed with the utmost attention to detail
to provide you with the highest standards in quality and performance. For product
support and updates, please refer to our website at http://www.supermicro.com/
products/nfo/networking.cfm#adapter.
1-2 Product Highlights
The product highlights of this add-on card include the following:
• Intel® Ethernet Controller XL710/X557 10GBase-T
• Low-Prole Standard Short-length Form Factor
• PCI Express 3.0 (8GT/s)
• Four (4) RJ45 Connectors
• Network Virtualization Ofoads: VxLAN and NVGRE
• Ethernet Flow Director
• Data Plane Developer Kit for Efcient Packet Processing
• Small Packet Performance
• Intelligent Ofoads
• Unied Networking Support for NAS and SAN
• Asset Management Features
• NC-SI for Remote Management (IPMI)
• RoHS compliant 6/6
• Supports Both Direct Attach Copper and Fiber Cables
1-1
AOC-STG-i4T Add-on Card User's Guide
1-3 Technical Specications
General
• Intel® Ethernet Controller XL710/X557 10GBase-T
• Half-length low-prole standard form factor
• PCI-E 3.0 x8 (8GT/s) interface
• Quad RJ45 connectors with speed up to 10Gb/s per port
• Load balancing on multiple CPUs
• Intel® PROSet Utility for Windows Device Manager
I/O Features
• Intel® Flow Director
• MSI-X support to minimize interrupt overhead and to allow load-balancing be-
tween multiple cores/CPUs
• Multiple queues: 1,536 Tx and Rx queues per port
• Tx/Rx IP, SCTP, TCP, and UDP checksum ofoading (IPv4, IPv6) capabilities
Virtualization Features
• Next-Generation VMDq with up to 256 VMDq VMs supported
• SR-IOV with up to 128 virtuals ports
• Virtual Machine Load Balancing (VMLB)
• Advanced Packet Filtering
• VLAN support for up to 4,096 VLAN tags
• VXLAN and NVGRE support
1-2
Chapter 1: Overview
Storage Interface Features
• Preboot eXecution Environment (PXE) support
• iSCSI remote boot
• iSCSI Acceleration
• Simple Network Management Protocol (SNMP) and Remote Network Monitoring
(RMON) static counters
Management Features
• Asset Management support on Supermicro® X10 generation platforms
• Controller asset tags such as part number, revision, serial number, and MAC
addresses
• Controller thermal sensor
• NC-SI for Remote Management
Advanced Software Features
• Teaming support
• IEEE 802.3ad (link aggregation control protocol)
• IEEE 802.1Q VLANs
• IEEE 802.3 2005 ow control support
• IEEE 802.1p
• TCP segmentation/large send ofoad
• Interrupt moderation
OS Support
The AOC-STG-i4T add-on card supports the following operating systems (OS):
• Windows® Server 2012 R2, 2012, 2008 R2 x86-64
1-3
AOC-STG-i4T Add-on Card User's Guide
• Linux RedHat EL 6.5 and 7.0 IA-32, X86-64, and IA-64
• Linux SuSE SLES 11 SP3 and 12 IA-32, X86-64, and IA-64
• FreeBSD 9 and 10 IA-32, X86-64, and IA-64
• UEFI 2.1 and 2.3 X86-64 and I-64
• VMware ESXi 5.1 and ESXi 5.5 X86-64
Power Consumption
• Typical power consumption: 15.5W
• Maximum power consumption: 19.8W
Operating Conditions
• Operating temperature: 0°C to 55°C (32°F to 131°F)
• Storage temperature: -40°C to 70°C (-40°F to 158°F)
• Storage humidity: 90% non-condensing relative humidity at 35°C
Physical Dimensions
• Card PCB dimensions: 5.9in (14.99cm) x 2.73in (6.90cm) (L x H)
• Height of end brackets: standard -- 4.725in (12cm), low-prole -- 3.13in (7.94cm)
Supported Platforms
• Supermicro motherboards with minimum PCI-E 3.0 x8 slot
• Supermicro server systems with low-prole or full-height PCI-E 3.0 x8 expan-
sion slots
• NC-SI is supported by Supermicro motherboards with corresponding connection
Note : This product is intended to be used with Supermicro server systems
or motherboards as an integrated solution package.
1-4
Chapter 1: Overview
1-4 Compliance/Operating Environment
The AOC-STG-i4T add-on card is compliant with the following environmental
regulations:
• RoHS Compliant 6/6, Pb Free
1-5
AOC-STG-i4T Add-on Card User's Guide
Notes
1-6
Chapter 2: Hardware Components
Chapter 2
Hardware Components
2-1 Add-On Card Image and Layout
The AOC-STG-i4T R1.00 Image
5.9"
1 2
REV: 1.00
DESIGNED IN USA
1
JNCSI
S1
7
JLAN1 JLAN2 JLAN3 JLAN4
3
Intel®
4
Coppervale
X557-AT4
Quad PHY
U1 U2
Intel® Fortville
XL710-BM1
5
6
10
AOC-STG-i4T
JGF1
The AOC-STG-i4T R1.00 Layout
1. Intel® XL710-BM1 6. RJ45 LAN Port 4
2. Intel® X557-AT4 7. JNCSI: NC-SI header
3. RJ45 LAN Port 1 8. LED1
4. RJ45 LAN Port 2 9. S1: DIP Switch
5. RJ45 LAN Port 3 10. JGF1: PCI-E 3.0 x8
2-1
C
LED1
9
2.73"
A
8
AOC-STG-i4T Add-on Card User's Guide
2-2 Major Components
The following major components are installed on the AOC-STG-i4T:
1. Intel® Ethernet Controller XL710/X557 10GBase-T
2. RJ45 LAN Ports 1~4
3. LED1: Overheat LED
4. JNCSI: NC-SI for IPMI support
5. S1: DIP Switch
2-2
Chapter 2: Hardware Components
2-3 LAN Ports and LAN LED indicators
LAN Ports
There are four LAN ports on the AOC-STG-i4T. These LAN ports support connec-
tion speeds of 10Gbps. Use a direct-attach RJ45 type LAN cable. See the layout
below for the location.
Note: Please refer to page 1-1 for recommended cables.
LAN Port LED Indicators
Each LAN port has two LEDs to indicate speed and data activity. Refer to the table
below for LED color and denition.
LAN Port Link LED (Left)
LED Color Denition
Green 10 Gbps
Amber 1 Gbps
Off 100 Mbps
JLAN1 JLAN2 JLAN3 JLAN4
1
1
1
1
LED State
Intel®
Coppervale
X557-AT4
Quad PHY
JGF1
Link LED
Intel® Fortville
XL710-BM1
AOC-STG-i4T
Activity LED
LAN Port Activity LED (Right)
LED State
LED Color Status Denition
Off Off No Connection
Green Solid Link
Green Flashing Active
DESIGNED IN USA
U1 U2
S1
1
JNCSI
REV: 1.00
C
LED1
A
1. LAN Ports
2-3
AOC-STG-i4T Add-on Card User's Guide
2-4 NC-SI Header & PCI-E 3.0 x8 Connector
NC-SI Header
A Network-Controller Sideband Interface (NC-SI) header is located at JNCSI on
the add-on card. Connect an appropriate cable from this header to a motherboard
to provide the out-of-band (sideband) connection between the onboard Baseboard
Management Controller (BMC) and a Network Interface Controller (NIC) for remote
management. For the network sideband interface to work properly, you will need
to use a motherboard that supports NC-SI and also need to have a special cable.
Please contact Supermicro at www.supermicro.com to purchase the cable for this
header. See the layout below for the location.
PCI-E 3.0 x8 Connector
A PCI-E 3.0 x8 connector is located at JGF1 on the add-on card. Insert this con-
nector into a PCI-E 3.0 x8 slot on a motherboard to use the AOC-STG-i4T add-on
card. See the layout below for the location.
JLAN1 JLAN2 JLAN3 JLAN4
Intel®
Coppervale
X557-AT4
Quad PHY
2
JGF1
Intel® Fortville
XL710-BM1
AOC-STG-i4T
DESIGNED IN USA
U1 U2
S1
1
JNCSI
REV: 1.00
1
C
LED1
A
1. NC-SI Header
2. PCI-E 3.0 x8
Connector
2-4
Chapter 2: Hardware Components
2-5 Overheat LED & DIP Switch
Overheat LED
An overheat LED at LED1 displays a warning if the add-on card is overheating.
Refer to the table below for the LED status. See the layout below for the location.
Overheat LED Status
State Denition
Solid Overheat
JLAN1 JLAN2 JLAN3 JLAN4
Intel®
Coppervale
X557-AT4
Quad PHY
JGF1
Intel® Fortville
XL710-BM1
AOC-STG-i4T
DESIGNED IN USA
U1 U2
S1
1
JNCSI
REV: 1.00
C
LED1
A
1
1. Overheat LED
2-5
AOC-STG-i4T Add-on Card User's Guide
DIP Switch
The DIP Switch at S1 provides SMBUS address selection. You can congure the
card with static SMBUS address. Refer to the tables below for address selections.
See the layout below for the location.
JLAN1 JLAN2 JLAN3 JLAN4
Intel®
Coppervale
X557-AT4
Quad PHY
JGF1
Intel® Fortville
XL710-BM1
AOC-STG-i4T
DESIGNED IN USA
U1 U2
S1
1
JNCSI
REV: 1.00
C
LED1
1
A
1. DIP Switch
2-6
Chapter 3: Installation
Chapter 3
Installation
3-1 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid dam-
aging your add-on card, it is important to handle it very carefully. The following
measures are generally sufcient to protect your equipment from ESD.
Precautions
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing the add-on card from the
antistatic bag.
• Handle the add-on card by its edges only; do not touch its components, or
peripheral chips.
• Put the add-on card back into the antistatic bags when not in use.
• For grounding purposes, make sure that your system chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the add-on card.
Unpacking
The add-on card is shipped in antistatic packaging to avoid static damage. When
unpacking your component or system, make sure that you are static protected.
Note: To avoid damaging your components and to ensure proper installa-
tion, be sure to always connect the power cord last, and always remove it
before adding, removing or changing any hardware components.
3-1
AOC-STG-i4T Add-on Card User's Guide
3-2 Before Installation
To install the add-on card properly, be sure to follow the instructions below.
1. Power down the system.
2. Unplug the power cord.
3. Use industry standard anti-static equipment (such as gloves or wrist strap)
and follow the precautions on Page 3-1 to avoid damage caused by ESD.
4. Familiarize yourself with the server, motherboard, and/or chassis documenta-
tion.
5. Conrm that your operating system includes the latest updates and hotxes.
3-3 Installing the Add-on Card
Follow the steps below to install the add-on card into your system.
1. Remove the server cover and, if any, set aside any screws for later use.
2. Remove the add-on card slot cover. If the case requires a screw, place the
screw aside for later use.
3. Position the add-on card in the slot directly over the connector, and gently
push down on both sides of the card until it slides into the PCI connector.
4. Secure the add-on card to the chassis. If required, use the screw that you
previously removed.
5. Attach any necessary external cables to the add-on card.
6. Replace the chassis cover.
7. Plug the power cord into the wall socket and power up the system.
3-2
Chapter 3: Installation
3-4 Installing Drivers on Windows
Follow the steps below to install the drivers for Windows. Download the drivers from
the Supermicro FTP site at ftp://ftp.supermicro.com/Networking_Drivers/.
1. Run the CDR-NIC.
2. When the SUPERMICRO window appears, click on the computer icon next to
the product model.
Note: If the FOUND NEW HARDWARE WIZARD screen displays on your
system, click CANCEL.
3. Click on INSTALL DRIVERS AND SOFTWARE.
4. Follow the prompts to complete the installation.
3-5 Installing Drivers on Linux
Follow the steps below to install the driver to a Linux system.
Build a Binary RPM Package
1. Run ‘rpmbuild -tb <lename.tar.gz>’
2. Replace <lename.tar.gz> with the specic lename of the driver.
Note: For the build to work properly, the current running kernel MUST
match the version and conguration of the installed kernel sources. If you
have just recompiled the kernel, reboot the system at this time.
3-3
AOC-STG-i4T Add-on Card User's Guide
Follow the instructions below to build the driver manually.
1. Move the base driver tar le to the directory of your choice. For example,
/home/username/ixgbe
or
/usr/local/src/ixgbe.
2. Untar/unzip archive:
tar zxf ixgbe-x.x.x.tar.gz
3. Change to the driver src directory:
cd ixgbe-x.x.x/src/
4. Compile the driver module:
make install
The binary will be installed as:
/lib/modules/[KERNEL_VERSION]/kernel/drivers/net/ixgbe/ixgbe.[k]o
The install locations listed above are the default locations. They might not be
correct for certain Linux distributions. For more information, see the ldistrib.txt
le included in the driver tar.
Note: IXGBE_NO_LRO is a compile time ag. The user can enable it at
compile time to remove support for LRO from the driver. The ag is used
by adding CFLAGS_EXTRA=-”DIXGBE_NO_LRO” to the make le when
it’s being compiled.
make CFLAGS_EXTRA=”-DIXGBE_NO_LRO” install
5. Load the module:
For kernel 2.6.x, use the modprobe command:
modprobe ixgbe <parameter>=<value>
For 2.6 kernels, the insmod command can be used if the full path to the driver
module is specied. For example:
insmod /lib/modules/<KERNEL VERSION>/kernel/drivers/net/ixgbe/ixgbe.ko
In addition, when using 2.6-based kernels, make sure that older ixgbe drivers
are removed from the kernel before loading the new module. To do this, use:
rmmod ixgbe; modprobe ixgbe
3-4
Chapter 3: Installation
6. Assign an IP address to the interface by entering the following, where x is the
interface number:
ifcong ethx <IP_address> netmask <netmask>
7. Verify that the interface works. Enter the following, where <IP_address> is the
IP address for another machine on the same subnet as the interface that is
being tested:
ping <IP_address>
3-6 Installing Drivers on FreeBSD
Follow the instructions below to install the drivers in FreeBSD kernel 4.8 or later.
In the instructions below, x.x.x is the driver version as indicated in the name of the
drive tar le.
Note : You must have kernel sources installed in order to compile the
driver module.
1. Move the base driver tar le to the dirctory of your choice. For example, use
/home/username/ixgb or /usr/local/src/ixgb.
2. Untar/unzip the archive:
tar xfz ixgb-x.x.x directory
3. To install man page:
cd ixgb-x.x.x
gzip -c ixgb.4 > /usr/share/man/man4/ixgb.4.gz
4. To load the driver onto a running system, perform the following steps:
cd ixgb-x.x.x
make
or
cd ixgb-x.x.x/src
make load
5. To assign an IP address to the interface, enter the following:
ifcong ixgb<interface_num> <IP_address>
3-5
AOC-STG-i4T Add-on Card User's Guide
6. Verify that the interface works. Enter the following, where <IP_address> is the
IP address for another machine on the same subnet as the interface that is
being tested:
ping <IP_address>
7. If you want the driver to load automatically when the system is booted:
cd ixgb-x.x.x/src
make load
cp if_ixgb.ko /modules
Edit /boot/loader.conf, and add the following line:
if_ixgb_load="YES"
or
compile the driver into the kernel (see item 8). Edit /etc/rc.conf, and create the
appropriate ifcong_ixgb<interface_num> entry:
ifcong_ixgb<interface_num>="<ifcong_settings>"
Example usage:
ifcong_ixgb0="inet 192.168.10.1 netmask 255.255.255.0"
8. If you want to compile the driver into the kernel, enter:
cd ixgb-x.x.x/src
mkdir /usr/src/sys/dev/ixgb
cp if_ixgb* /usr/src/sys/dev/ixgb
cp ixgb* /usr/src/sys/dev/ixgb
cp Makele.kernel /usr/src/sys/modules/ixgb/Makele
Edit the /usr/src/sys/conf/les.i386 le, and add the following line:
dev/ixgb/ixgb_hw.c optional ixgb
dev/ixgb/ixgb_ee.c optional ixgb
dev/ixgb/if_ixgb.c optional ixgb
Remove the following lines from the /usr/src/sys/conf/les.i386 le, if they exist:
/dev/ixgb/if_ixgb_fx_hw.c optional ixgb
/dev/ixgb/if_ixgb_phy.c optional ixgb
3-6
Chapter 3: Installation
Edit the kernel conguration le (i.e., GENERIC or MYKERNEL) in /usr/src/sys/
i386/conf, and ensure the following line is present:
device ixgb
Compile and install the kernel. Reboot the system for the kernel updates to
take affect.
3-7
AOC-STG-i4T Add-on Card User's Guide
3-7 Asset Management Features
Asset Management is a new feature that allows users to monitor selected
Supermicro add-on cards in selected Supermicro X10 generation server systems.
Using Supermicro's proprietary management software, users will be able to moni-
tor the following:
1. Model name
2. Revision
3. Serial number
4. Temperature
3-8
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result
in signicant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims
any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.