Page 1
AOC-STG-i4S
User's Guide
Revision 1.0a
Page 2
The information in this User's Guide has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this user's guide, or to
notify any person or organization of the updates. Please Note: For the most up-to-date version
of this user's guide, please see our Website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this user's guide at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
User's Guide Revision 1.0a
Release Date: February 10, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Page 3
Preface
About this User's Guide
This user's guide is written for system integrators, IT technicians and
knowledgeable end users. It provides information for the installation and use of the
AOC-STG-i4S add-on card.
About this Add-on Card
The STG-i4S is an advanced, market-leading 10GbE SFP+ controller. The four LAN
ports on the card provide a connection speed of 10 Gbps. The card features the
Intel® XL170-AM1 controller and is supported on the Windows and Linux operating
systems. It expands virtualization beyond the server level to the network level, and
combines with hardware optimizations and ofoads. It provides unmatched features
for virtualization, exibility for LAN and SAN networks, and reliable performance.
This is the best choice for rapid provisioning of networks in an agile data center.
This product is sold only as part of an integrated solution with Supermicro® server
systems.
Preface
An Important Note to the User
All images and layouts shown in this user's guide are based upon the latest PCB
revision available at the time of publishing. The card you have received may or may
not look exactly the same as the graphics shown in this user's guide.
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before
any warranty service will be rendered. You can obtain service by calling your ven-
dor for a Returned Merchandise Authorization (RMA) number. When returning the
motherboard to the manufacturer, the RMA number should be prominently displayed
on the outside of the shipping carton, and the shipping package is mailed prepaid
or hand-carried. Shipping and handling charges will be applied for all orders that
must be mailed when service is complete. For faster service, you can also request
a RMA authorization online http://www.supermicro.com/RmaForm/.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alternation, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor rst for any product problems.
iii
Page 4
AOC-STG-i4S Add-on Card User's Guide
Conventions Used in the User's Guide
Pay special attention to the following symbols for proper system installation and for
safety instructions to prevent damage to the system or injury to yourself:
Warning: Important information given to ensure proper system installation
or to prevent damage to the components or injury to yourself.
Note: Additional information given for proper system setup.
Naming Convention for Standard Network Adaptors
A O C – S T G N – i 2 S
1 – 2 3 4 – 5 6 7
Character Representation Options
1st Product Family AOC: Add On Card
2nd Form Factor U: UIO, S: Standard, P: Proprietary, C: MicroLP
3rd Product Type/Speed G: GbE (1Gb/s), TG: 10GbE (10Gb/s), 40G: 40GbE
4th Chipset Model (Optional) N: Niantec (82599), P: Powerville (i350),
5th Chipset Manufacturer i: Intel, m: Mellanox, b: Broadcom
6th Number of Ports 1: 1 port, 2: 2 ports, 4: 4 ports
7th Connector Type (Optional) S: SFP+, T:
(40Gb/s), 100G: 100GbE (100Gb/s), IBF: IB FDR
(56Gb/s), IBQ: IB QDR (40Gb/s), INF: InfiniBand DDR
(20Gb/s)
10GBase-T, Q: QSFP+, C: QSFP28
Networking Adapter List
Model Type Form Factor Interface Controller Connection
SGP-i2 GbE Standard LP PCI-E x4 Intel® i350AM2 2 RJ45 (1Gb/port) 3.9” (9.9cm) x 2.73” (6.9cm) 3.5
SGP-i4 GbE Standard LP PCI-E x4 Intel® i350 4 RJ45 (1Gb/port) 3.9” (9.9cm) x 2.73” (6.9cm) 5
STG-b4S 10GbE Standard LP PCI-E x8 Broadcom® BCM57840S 4 SFP+ (10Gb/port) 5.4” (13.7cm) x 2.73” (6.9cm) 14
STG-i2T 10GbE Standard LP PCI-E x8 Intel®
STGN-i2S 10GbE Standard LP PCI-E x8 Intel® 82599ES 2 SFP+ (10Gb/port) 4.0” (10.2cm) x 2.73” (6.9cm) 11.2
STGN-i1S 10GbE Standard LP PCI-E x8 Intel® 82598EN 1 SFP+ (10Gb/port) 4.0” (10.2cm) x 2.73” (6.9cm) 10
STG-i2 10GbE Standard LP PCI-E x8 Intel® 82598EB 2 CX4 (10Gb/port) 5.56” (14.1cm) x 2.19” (5.6cm) 6.5
STG-i4S 10GbE Standard LP PCI-E x8 Intel® XL710-AM1 4 SFP+ (10G
S40G-i2Q 40GbE Standard LP PCI-E x8 Intel® XL710-AM2 2 QSFP+ (40Gb/port) 5.9” (14.9cm) x 2.73” (6.9cm) 7
PTG-i1S 10GbE Proprietary PCI-E x8 Intel® 82599EN 1 SFP+ (10Gb/port) 10.04” (25.5cm) x .78” (2.0cm) 7.5
UG-i4 GbE UIO FH PCI-E x8 Intel® 82571EB 4 RJ45 (1Gb/port) 6.6” (16.7cm) x 3.9” (9.8cm) 10
UIBF-m1 FDR IB UIO LP PCI-E x8 Mellanox® ConnectX-3 1 QSFP (56Gb/port) 5.63” (14.3cm) x 2.73”
UIBQ-m1 QDR IB UIO LP PCI-E x8 Mellanox® ConnectX-2 1 QSFP (40Gb/port) 5.63” (14.3cm) x 2.73” (6.9cm) 7
UIBQ-m2 QDR IB UIO LP PCI-E x8 Mellanox® ConnectX-2 2 QSFP (40Gb/port) 5.63” (14.3cm) x 2.73” (6.9cm) 8
CGP-i2 GbE MicroLP PCI-E x4 Intel® i350 2 RJ45 (1Gb/port) 4.45” (11.3cm) x 1.54” (3.9cm) 4
CG-i2 GbE MicroLP PCI-E x4 Intel® 82580 2 RJ45 (1Gb/port) 4.45” (11.3cm) x 1.3” (3.4cm) 4
CIBF-m1 FDR IB MicroLP PCI-E x8 Mella
CIBQ-m1 QDR IB MicroLP PCI-E x8 Mellanox® ConnectX-3 1 QSFP (40Gb/port) 4.85" (12.3cm) x 1.54" (3.9cm) 7
CTG-i1S 10GbE MicroLP PCI-E x8 Intel® 82599EN 1 SFP+ (10Gb/port) 4.85" (12.3cm) x 1.54" (3.9cm) 10
CTG-i2S 10GbE MicroLP PCI-E x8 Intel® 82599ES 2 SFP+ (10Gb/port) 4.85" (12.3cm) x 1.54" (3.9cm) 11
CTG-i2T 10GbE MicroLP PCI-E x8 Intel® X540 2 RJ45 (10Gb/p ort) 4
X540 2 RJ45 (10Gb/port) 5.9” (14.99cm) x 2.73” (6.9cm) 13
b/port) 5.9” (14.9cm) x 2.73” (6.9cm) 8
nox® ConnectX-3 1 QSFP (56Gb/port) 4.85" (12.3cm) x 1.54" (3.9cm) 7
iv
Dimension
(w/o Brackets) (L x H)
(6.9cm) 7
.8” (12.3cm) x 2.75” (7.7cm) 13
Power
(W)
Page 5
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Website: www.supermicro.nl
Preface
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Email: support@supermicro.com.tw
Website: www.supermicro.com.tw
v
Page 6
AOC-STG-i4S Add-on Card User's Guide
Table of Contents
Preface
Chapter 1 Overview
1-1 Overview ......................................................................................................... 1-1
1-2 Product Highlights ........................................................................................... 1-1
1-3 Technical Specications .................................................................................. 1-2
General ............................................................................................................ 1-2
I/O Features .................................................................................................... 1-2
Virtualization Features..................................................................................... 1-2
Storage Interface Features ............................................................................. 1-3
Management Features .................................................................................... 1-3
Advanced Software Features .......................................................................... 1-3
OS Support ..................................................................................................... 1-4
Cable Support ................................................................................................. 1-4
Power Consumption ........................................................................................ 1-4
Physical Dimensions ....................................................................................... 1-4
Optional Accessories ..................................................................................... 1-4
Operating Conditions ...................................................................................... 1-5
Compliance Platforms ..................................................................................... 1-5
Supported Platforms ....................................................................................... 1-5
Chapter 2 Hardware Components
2-1 Add-On Card Image and Layout ..................................................................... 2-1
2-2 Major Components .......................................................................................... 2-1
2-3 LAN Ports and LAN LED Indicators ................................................................ 2-2
2-4 Connectors and Switches ............................................................................... 2-3
Chapter 3 Installation
3-1 Static-Sensitive Devices .................................................................................. 3-1
3-2 Before Installation ........................................................................................... 3-1
3-3 Installing the Add-on Card .............................................................................. 3-2
3-4 Installing the Drivers in Windows .................................................................... 3-3
3-5 Installing the Drivers in Linux .......................................................................... 3-4
3-6 Building the Driver Manually ........................................................................... 3-4
vi
Page 7
Chapter 1: Overview
Chapter 1
Overview
1-1 Overview
Congratulations on purchasing your add-on card from an acknowledged leader in
the industry. Supermicro products are designed with the utmost attention to detail
to provide you with the highest standards in quality and performance. For product
support and updates, please refer to our website at http://www.supermicro.com/
products/nfo/networking.cfm#adapter.
1-2 Product Highlights
The product highlights of this add-on card include the following:
• Quad SFP+ Ports
• Standard Low-Prole Form Factor
• PCI Express 3.0 (8GT/s)
• Network Virtualization Ofoads including VXLAN and NVGRE
• Small Packet Performance
• Data Plane Developer Kit for efcient packet processing
• Low Power Consumption
• Intel® Flow Director
• Intelligent Ofoads
• Unied networking providing a single wire support for LAN and storage
• Asset Management Features
• RoHS compliant 6/6
• Supports Both Direct Attach Copper and Fiber Cables
1-1
Page 8
AOC-STG-i4S Add-on Card User's Guide
1-3 Technical Specications
General
• Intel® XL710-AM1 controller
• Low Prole Standard form factor
• PCI-E 3.0 x8 (8GT/s) interface
• Quad SFP+ connectors with speed up to 10Gbps per port
• Load balancing on multiple CPUs
• Intel® PROSet Utility for Windows Device Manager
• Time Sync (IEEE 1588)
• Energy Efcient Ethernet (EEE)
I/O Features
• Intel® Flow Director
• MSI-X support
• Multiple Queues: 1,536 TX and RX queues per port
• Tx/Rx IP, SCTP, TCP, and UDP checksum ofoading (IPv4, IPv6) capabilities
• Jumbo Frame (9.5KB)
Virtualization Features
• Next-Generation VMDq with up to 256 VMDq VMs supported
• PCI-SIG SR-IOV with up to 128 virtual ports
• Virtual Machine Load Balancing (VMLB)
• Advanced Packet Filtering
• VLAN support for up to 4096 VLAN tags
1-2
Page 9
Chapter 1: Overview
• VXLAN and NVGRE support
Storage Interface Features
• Preboot eXecution Environment (PXE) support
• iSCSI remote boot
• Simple Network Management Protocol (SNMP) and Remote Network Monitoring
(RMON) static counters
Management Features
• Asset Management support on Supermicro® X10 generation platforms
• Controller asset tags such as part number, revision, serial number, and MAC
addresses
• Controller thermal sensor
Advanced Software Features
• Teaming support
• IEEE 802.3ad (link aggregation control protocol)
• IEEE 802.1Q VLANs
• IEEE 802.3 2005 ow control support
• IEEE 802.1p
• TCP segmentation/large send ofoad
• Interrupt moderation
1-3
Page 10
AOC-STG-i4S Add-on Card User's Guide
OS Support
The AOC-STG-i4S add-on card supports the following operating systems:
• Windows® Server 2012 R2, 2012, 2008 R2 X86-64
• Linux RedHat EL 6.5 and 7.0 IA-32, X86-64, and IA-64
• Linux SuSE SLES 11 SP3 and 12 IA-32, X86-64, and IA-64
• FreeBSD 9 and 10 IA-32, X86-64, and IA-64
• UEFI 2.1 and 2.3 X86-64 and I-64
• VMware ESXi 5.1 and ESXi 5.5 X86-64
Cable Support
• SFP+ direct-attach twinaxial copper cables up to 7m
• Fiber-optic cables (with required optional SFP+ transceivers)
Power Consumption
• Typical power consumption: 4W
• Maximum power consumption: 8W
Physical Dimensions
• Card PCB dimensions: 14.99cm (5.9in) x 6.90cm (2.73in) (L x H)
• Height of end brackets: Standard 12cm (4.725in), low-prole 7.94cm (3.13in)
Optional Accessories
• AOC-E10GSFPSR: SFP+ transceiver module for short range ber cables (up
to 300m)
• AOC-E10GSFPLR: SFP+ transceiver module for long range ber cables (up to
3000m)
• AOC-TSR-FS: SFP+ transceiver module for short range ber cables (up to 300m)
1-4
Page 11
Chapter 1: Overview
• CBL-0347L: 39.37” (100cm) 10GbE SFP+ to SFP+, Twinaxial copper cable
• CBL-0348L: 118.11” (300cm) 10GbE SFP+ to SFP+, Twinaxial copper cable
• CBL-0349L: 196.85” (500cm) 10GbE SFP+ to SFP+, Twinaxial copper cable
Operating Conditions
• Operating temperature: 0°C to 55°C (32°F to 131°F)
• Storage temperature: -40°C to 70°C (-40°F to 158°F)
• Storage humidity: 90% non-condensing relative humidity at 35°C
Compliance Platforms
• RoHS Compliant 6/6, Pb Free
Supported Platforms
• Supermicro® motherboards with minimum one PCI-E x8 slot
• Supermicro® server systems with minimum one low-prole or full-height PCI-E
x8 expansion slot
1-5
Page 12
AOC-STG-i4S Add-on Card User's Guide
Notes
1-6
Page 13
Chapter 2: Hardware Components
Chapter 2
Hardware Components
2-1 Add-On Card Image and Layout
1
1
1
2
1
3
1
4
1
5
The AOC-STG-i4S Image
1
8
1
7
1
6
J1_SFP
1
2
1
3
1
4
1
5
P0
D3
P1
D5
P2
D7
P3
D9
1
1
DESIGNED IN USA
JGF1
The AOC-STG-i4S Layout
2-2 Major Components
The following major components are on the AOC-STG-i4S
1. Intel XL710-AM1 5. SFP+ Port 3
2. SFP+ Port 0 6. Thermal Alert
3. SFP+ Port 1 7. DIP Switch
4. SFP+ Port 2 8. Thermal Alert LED
2-1
AOC-STG-i4S
REV: 1.01
JNCSI1
1
LED3
8
JP1
1
7
S1
JP2
1
6
Page 14
AOC-STG-i4S Add-on Card User's Guide
J1_SFP
2-3 LAN Ports and LAN LED Indicators
LAN Ports
There are four SFP+ LAN ports on the add-on card. These LAN ports support con-
nection speeds of 10Gbps and 1Gbps. Use a direct-attach twinaxial copper cable.
Note: Please refer to "Optional Accessories" on page 1-4 for recommended
cables.
The AOC-STG-i4S Layout
1
1
1
2
1
3
1
4
P0
D3
P1
D5
P2
D7
P3
D9
DESIGNED IN USA
AOC-STG-i4S
REV: 1.01
JNCSI1
JGF1
LED3
JP1
S1
JP2
LAN Port LED Indicators
Each LAN port has two LEDs to indicate speed and data activity. Refer to the table
below for LED color and denition.
Link LED
Activity LED
LED Color Denition
LNK Green 10 Gb Link Speed
Yellow 1 Gb Link Speed
ACT Blinking Green Activity
LAN Ports
1. SFP+ Port 0
2. SFP+ Port 1
3. SFP+ Port 2
4. SFP+ Port 3
2-2
Page 15
2-4 Connectors and Switches
Chapter 2: Hardware Components
Thermal Alert Connector
Connect an external cable (not included) from
the motherboard to the thermal alert connector at
JP2 to monitor the chipset die temperature. Refer
to the table on the right for the pin denition.
Refer to page 2-1 for the location of the jumper.
Thermal Alert LED
A thermal alert LED is located at LED3. The yel-
low LED indicates there is a thermal alert. Refer
to the table on the right for the LED status. Refer
to page 2-1 for the location of the LED.
Thermal Alert
Pin Denition
Pin Denition
1 GND
2 Thermal_Alert_N
3 GND
Thermal Alert
LED Status
Color Status
Yellow Thermal Alert
2-3
Page 16
AOC-STG-i4S Add-on Card User's Guide
DIP Switch
The DIP Switch at S1 provides SMBUS address selection. You can congure the
card with static SMBUS address. Refer to the tables below for address selections.
Refer to page 2-1 for the location of the switch.
2-4
Page 17
Chapter 3: Installation
Chapter 3
Installation
3-1 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid dam-
aging your add-on card, it is important to handle it very carefully. The following
measures are generally sufcient to protect your equipment from ESD.
Precautions
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing the add-on card from the
antistatic bag.
• Handle the add-on card by its edges only; do not touch its components or
peripheral chips.
• Put the add-on card back into the antistatic bags when not in use.
• For grounding purposes, make sure that your system chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the add-on card.
Unpacking
The add-on card is shipped in antistatic packaging to avoid static damage. When
unpacking your component or your system, make sure that the person handling it
is static protected.
Note: To avoid damaging your components and to ensure proper installa-
tion, be sure to always connect the power cord last, and always remove it
before adding, removing or changing any hardware components.
3-2 Before Installation
To install the add-on card properly, be sure to follow the instructions below.
1. Power down the system.
3-1
Page 18
AOC-STG-i4S Add-on Card User's Guide
2. Unplug the power cord.
3. Use industry-standard anti-static equipment (such as gloves or wrist strap)
and follow the instructions listed on page 3-1 to avoid damage caused by
ESD.
4. Familiarize yourself with the server, motherboard, and/or chassis documenta-
tion.
5. Conrm that your operating system includes the latest updates and hotxes.
3-3 Installing the Add-on Card
Follow the steps below to install the add-on card into your system.
1. Remove the server cover and, if necessary, set aside any screws for later
use.
2. Remove the add-on card slot cover and its screw.
3. Position the add-on card in the slot directly over the connector and gently
push down on both sides of the card until it slides into the PCI connector.
4. Secure the add-on card to the chassis. If required, use the screw that you
previously removed.
5. Attach any necessary external cables to the add-on card.
6. Replace the server cover.
7. Plug in the power cord and power up the system.
3-2
Page 19
Chapter 3: Installation
3-4 Installing the Drivers in Windows
Follow the steps below to install the drivers for Windows. Download the latest CDR-
NIC drivers from ftp://ftp.supermicro.com/Networking_Drivers/.
1. Run the CDR-NIC drivers installation.
2. When the SUPERMICRO window appears, click on the computer icon next to
the product model.
Note: If the FOUND NEW HARDWARE WIZARD screen displays on your
system, click CANCEL.
3. Click on INSTALL DRIVERS AND SOFTWARE.
4. Follow the prompts to complete the installation.
3-3
Page 20
AOC-STG-i4S Add-on Card User's Guide
3-5 Installing the Drivers in Linux
Follow the steps below to install the driver to a Linux system.
Build a Binary RPM Package
1. Run ‘rpmbuild -tb <lename.tar.gz>’
2. Replace <lename.tar.gz> with the specic lename of the driver.
Note: For the build to work properly, the current running kernel MUST
match the version and conguration of the installed kernel sources. If you
have just recompiled the kernel, reboot the system at this time.
3-6 Building the Driver Manually
Follow the instructions below to build the driver manually.
1. Move the base driver tar le to the directory of your choice. For example, use
'/home/username/e1000' or '/usr/local/src/e1000'.
2. Untar/unzip the archive, where <x.x.x> is the version number for the driver
tar le:
tar zxf e1000-<x.x.x>.tar.gz
3. Change to the driver src directory, where <x.x.x> is the version number for
the driver tar:
cd e1000-<x.x.x>/src/
4. Compile the driver module:
# make install
The binary will be installed as:
/lib/modules/<KERNEL VERSION>/kernel/drivers/net/e1000/e1000.[k]o
The install location listed above is the default location. This may differ for various
Linux distributions.
5. Load the module using either the insmod or modprobe command:
modprobe e1000
insmod e1000
Note that for 2.6 kernels the insmod command can be used if the full path to the
driver module is specied. For example:
insmod /lib/modules/<KERNEL VERSION>/kernel/drivers/net/e1000/e1000.ko
3-4
Page 21
Chapter 3: Installation
With 2.6 based kernels also make sure that older e1000 drivers are removed from
the kernel, before loading the new module:
rmmod e1000; modprobe e1000
6. Assign an IP address to the interface by entering the following, where <x> is
the interface number:
ifcong eth<x> <IP_address>
7. Verify that the interface works. Enter the following, where <IP_address> is the
IP address for another machine on the same subnet as the interface that is being
tested:
ping <IP_address>
3-5
Page 22
AOC-STG-i4S Add-on Card User's Guide
3-6
Page 23
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result
in signicant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims
any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Loading...