Superior DRC3035DEN, DRT3045 series, DRT3035 series, DRT3040 series, DRC3040DEN Installation And Operation Instructions Manual

Installation and Operation Instructions

PFS

USC

P900285-00

SuperiorTM DRT3000 and DRC3000 Series Direct-Vent Gas
Fireplaces

P/N 900285-00 Rev. E 05/2015

Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900285-02.

Report No. F13-094

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with
this appliance and shall be installed for
the protection of children and other at-risk

Models
DRT3033xxx* DRT3035xxx*

®

DRC3035DEN

DRT3040xxx*
DRC3040DEN

DRT3045xxx*

* “xxx” indicates unique model identifiers.
This manual covers all SuperiorTM DRT3000 and DRC3000 models.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.

L’écran pare-étincelles fourni avec ce foyer réduit le
risque de brûlure en cas de contact accidentel avec la
vitre chaude et doit être installé pour la protection Des
enfants et Des personnes à risques.

individuals.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements
locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque
signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

WARNING:

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result
in serious injury, death, or property damage.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other
appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any
phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh­bor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire
department.

— Installation and service must be performed by a

qualified installer, service agency or the gas sup­plier.

AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité
pourrait d’entraîner des blessures graves, la mort
ou des dommages matériels.

— Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inflammables dans le voisin­age de cet appareil ou de tout autre appareil.

— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous
servir des téléphones se trouvant dans le bâti­ment où vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service des incindies.

— L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié
ou par le fournisseur de gaz.

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

General Information
900285-00 05/2015

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass
is provided with this appliance and shall be installed for the protection of
children and other at-risk individuals.

See attached color flyer for proper color representation

DANGER

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en
cas de contact accidentel avec la vitre chaude et doit être installé pour la
protection Des enfants et Des personnes à risques.

Voir ci-joint tract pour une bonne représentation de la couleur

PELIGRO

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

Una barrera diseñada para reducir el riesgo de quemaduras desde la
mirilla (vidrio) caliente es proveida con este aparato y deberá instalarse
para la protección de los niños y otros individuos en riesgo.

2

Vea el volante adjunto para la representación de color adecuado

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

General Information
900285-00 05/2015

Safety and Your

Fireplace

All parts of your

IHP fireplace get

EXTREMELY HOT!

 To prevent severe

burns and injuries,
install a screen or
physical barrier to
prevent direct contact
with the glass.

 Follow the safety instructions

below and be sure everyone in
your household understands this
burn hazard:

• The surfaces on your fireplace get
EXTREMELY HOT!

• The glass on the front of the
fireplace reaches EXTREMELY
HIGH temperatures and can cause
severe burns if touched.

• Keep children away from an
operating fireplace. Closely
supervise children in any room
where a fireplace is operating to
prevent contact with glass.

• Keep clothing, furniture,
gasoline, and other flammable
liquids away from the fireplace.

• Even after the gas is turned
off, fireplace surfaces remain
extremely hot.

 Be sure to attach the enclosed

Safety-in-Operation Warnings where
you turn on your fireplace, to help
remind everyone of the dangers
associated with high temperatures
(Page 47).

 Read Important Safety Information

(Page 5)

3

EXTRÊMEMENT CHAUDES !

La sécurité et

votre foyer

Toutes les parties de votre

foyer IHP deviennent

 Afin d'éviter de vous

brûler gravement ou de
vous blesser, installez
une grille ou une barrière
physique pour empêcher
tout contact direct avec la vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous les
membres de votre famille soient conscients
du danger de brûlure encouru :

• Les surfaces de votre foyer deviennent
EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du
foyer atteint des températures
EXTRÊMEMENT ÉLEVÉES et peut
causer de graves blessures en
cas de contact.

• Tenez les enfants à l'écart
du foyer lorsqu'il fonctionne.
Surveillez attentivement les
enfants dans les pièces où un
foyer est utilisé afin d'éviter qu'ils
ne soient en contact avec la vitre.

• Tenez tous les vêtements, les
meubles, l'essence et tout autre liquide
inflammable à l'écart du foyer.

• Même après fermeture du gaz,
les surfaces du foyer restent
extrêmement chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité
d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous
les utilisateurs les dangers liés aux
températures élevées (Page 47).

 Lisez L’information de sûreté

importante (Page 5).

[FRENCH][ENGLISH]

Seguridad y su

chimenea

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

 Instale una malla o barrera física para evitar

el contacto directo con el vidrio y prevenir
las quemaduras y lesiones graves.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que
todos en su hogar sepan acerca de
este peligro de quemadura:

• ¡Las superficies de la chimenea
se ponen MUY CALIENTES!

• El vidrio delante de la
chimenea alcanza temperaturas
EXTREMADAMENTE ALTAS
y puede causar quemaduras
graves si se toca.

• Mantenga a los niños alejados de
la chimenea en funcionamiento.
Supervise en forma cercana a los
niños en cualquier cuarto donde haya
una chimenea funcionando para
impedir el contacto con el vidrio.

• Mantenga la ropa, mobiliario,
gasolina y otros líquidos
inflamables alejados de la
chimenea.

• Aún después de haber apagado
el gas, las superficies de
la chimenea permanecen
extremadamente calientes.

 Asegúrese de colocar las Etiquetas

de advertencia de seguridad
de operación en el lugar donde

enciende la chimenea, para que todos
recuerden los peligros asociados con
las altas temperaturas (Página 47).

 Lea Información importante de

seguridad (Página 5).

[SPANISH]

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR BUSINESS!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety
information. Following these safety, care, and operation instructions will help ensure many years of dependable and
enjoyable service from your fireplace.

General Information
900285-00 05/2015

Space Reserved

for

Contemporary Image

Please read and understand these instructions before installing,
operating, or servicing this product.

General Information

Important Safety Information ............................................................5

Fireplace Installation, Operation, and Maintenance Notices ............... 6

Packaging .......................................................................................... 8

Introduction ....................................................................................... 8

Installation

Requirements for the Commonwealth of Massachusetts ................10

Cold Climate Insulation .................................................................... 10

Manufactured Home Requirements ................................................. 11

Location ...........................................................................................11

Vent Termination Clearances ...........................................................12

Minimum Clearances to Combustibles ............................................14

Wall Finishes / Surrounds / Mantels ................................................15

Installation Preparation ....................................................................15

Installation Sequence ......................................................................16

Construct the Fireplace Framing ...................................................... 16

Route the Gas Supply Line to the Fireplace .....................................18

Install the Vent System ....................................................................25

Complete the Field Wiring ................................................................37

Install the [Optional] Blower Kit after Installation in the Framing ..... 39

We recommend that our
gas hearth products be
installed and serviced by
professionals who are
certied in the U.S. by the
National Fireplace Institute®
(NFI) as NFI Gas Specialists.

Connect the Gas Line ....................................................................... 40

Verify Proper Fireplace Operation ....................................................41

Optional: Install the Firebox Liners ..................................................42

Install the Logs, Volcanic Stone, and Glowing Embers or Glass

Media ...............................................................................................42

Install the Glass Door ......................................................................42

Adjust the Air Shutter to Ensure Proper Flame Appearance ............. 42

Install the Hood ...............................................................................43

Install the Finishing Materials .......................................................... 44

Attach the Safety-in-Operation Warnings.........................................47

Installation Accessories ................................................................... 48

Gas Conversion Kits ........................................................................49

Operation

Maintenance .................................................................................... 63

Accessory Components ................................................................... 66

Lighting Instructions .......................................................................70

Troubleshooting ...............................................................................76

Replacement Parts ..........................................................................78

Warranty ..........................................................................................81

4

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

General Information
900285-00 05/2015

GENERAL INFORMATION

IMPORTANT SAFETY INFORMATION L’information de sûreté importante Información importante de seguridad

WARNING AVERTISSEMENT ADVERTENCIA

Do not operate appliance with the
glass front removed, cracked or
broken.

Do not use this fireplace if any part has
been under water. Immediately call a
qualified service technician to inspect the
fireplace and to replace any part of the
control system and any gas control which
has been under water.

Due to high temperatures, the fireplace
should be located out of traffic and away
from furniture and draperies.

Children and adults should be alerted to
the hazards of high surface temperature
and should stay away to avoid burns or
clothing ignition.

Clothing or other flammable material
should not be placed on or near the
fireplace.

Young children should be carefully
supervised when they are in the same
room as the fireplace. Toddlers, young
children, and others may be susceptible
to accidental contact burns. A physical
barrier is recommended if there are
at-risk individuals in the house. To
restrict access to a fireplace or stove,
install an adjustable safety gate to keep
toddlers, young children, and other at­risk individuals out of the room and away
from hot surfaces.

Any safety screen or guard removed for
servicing a fireplace must be replaced
prior to operating the fireplace.

Installation and repair should be done
by a qualified service person. The
fireplace should be inspected before use
and at least annually by a professional
service person. More frequent cleaning
may be required due to excessive lint
from carpeting, bedding material, et
cetera. It is imperative that control
compartments, burners, and circulating
air passageways of the fireplace be kept
clean (Maintenance on Page 63).

[English] [French] [Spanish]

Ne pas utiliser l’appareil si le
panneau frontal en verre n’est pas
en place, est craqué ou brisé.

Ne pas utiliser cet appareil s’il a été
plongé, même partiellement, dans l’eau.
Appeler un technicien qualifié pour
inspecter l’appareil et remplacer toute
partie du système de commande et toute
commande qui a été plongée dans l’eau.

En raison des températures élevées,
l’appareil devrait être installé dans un
endroit où il y a peu de circulation et loin
du mobilier et des tentures.

Les enfants et les adultes devraient être
informés des dangers que posent les
températures de surface élevées et se
tenir à distance afin d’éviter des brûlures
ou que leurs vêtements ne s’enflamment.

On ne devrait pas placer de vêtements
ni d’autres matières inflammables sur
l’appareil ni à proximité.

Les jeunes enfants devraient être
surveillés étroitement lorsqu’ils se
trouvent dans la même pièce que
l’appareil. Les tout petits, les jeunes
enfants ou les adultes peuvent subir des
brûlures s’ils viennent en contact avec
la surface chaude. Il est recommandé
d’installer une barrière physique si des
personnes à risques habitent la maison.
Pour empêcher l’accès à un foyer ou à un
poêle, installez une barrière de sécurité
; cette mesure empêchera les tout petits,
les jeunes enfants et toute autre personne
à risque d’avoir accès à la pièce et aux
surfaces chaudes.

Tout écran ou protecteur retiré pour
permettre l’entretien de l’appareil doit
être remis en place avant de mettre
l’appareil en marche.

L’installation et la réparation devrait
être confiées à un technicien qualifié.
L’appareil devrait faire l’objet
d’une inspection par un technicien
professionnel avant d’être utilisé et au
moins une fois l’an par la suite. Des
nettoyages plus fréquents peuvent être
nécessaires si les tapis, la literie, et
cetera produisent une quantité importante
de poussière. Il est essentiel que les
compartiments abritant les commandes,
les brûleurs et les conduits de circulation
d’air de l’appareil soient tenus propres
(Page 63).

No opere el artefacto con el frente
de vidrio quitado, agrietado o roto.

No use este artefacto si alguna de sus
partes ha estado bajo agua. Llame
de inmediato a un técnico de servicio
calificado para que inspeccione el
artefacto y reemplace cualquier parte del
sistema de control y cualquier control de
gas que haya estado bajo agua.

Debido a las altas temperaturas, el
artefacto debe situarse fuera de las
áreas de tráfico y lejos del mobiliario y
cortinas.

Se debe alertar a los niños y adultos
sobre los peligros de las altas
temperaturas en la superficie y que
se mantengan alejados para evitar
quemaduras o ignición de la ropa.

No debe colocarse ropa u otros
materiales inflamables sobre y cerca del
artefacto.

Se debe supervisar de cerca a los niños
cuando estén en el mismo cuarto que
el artefacto. Los niños pequeños, los
jóvenes y otras personas pueden ser
susceptibles a quemaduras por contacto
accidental. Se recomienda instalar
una barrera física si hay personas en
riesgo en la casa. Para restringir el
acceso a una chimenea o estufa, instale
una puerta de seguridad ajustable
para mantener a los niños pequeños,
jóvenes y otras personas en riesgo fuera
del cuarto y lejos de las superficies
calientes.

Cualquier malla o resguardo de seguridad
quitado para dar servicio a un artefacto,
debe reinstalarse antes de operar
el artefacto.

Una persona de servicio competente
debe realizar la instalación y reparación.
Una persona de servicio profesional
debe inspeccionar el artefacto antes
de usar al menos una vez por año. Se
puede requerir limpieza más frecuente
debido a la pelusa excesiva del
alfombrado, del material de cobijas,
etc. Es imprescindible mantener limpios
los compartimientos de control, los
quemadores y los pasajes de circulación
del aire del artefacto (Página 63).

5

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

FIREPLACE INSTALLATION, OPERATION, AND MAINTENANCE NOTICES

DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION OF THE APPLIANCE OR ITS COMPONENTS. ANY
MODIFICATION OR ALTERATION MAY VOID THE WARRANTY, CERTIFICATION, AND LISTINGS OF THIS UNIT.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to this manual. For assistance or additional information consult a
qualified installer, service agency or the gas supplier.

AVERTISSEMENT

Une installation, un réglage,une modification, une réparation ou un entretien mal effectué
peut causer des dommages matériels ou des blessures. Voir la notice de l’utilisateur qui
accompagne l’appareil. Pour de l’aide ou des renseignements supplémentaires, consultez
un installateur, un technicien agréé ou le fournisseur de gaz.

WARNING

General Information
900285-00 05/2015

Failure to comply with these installation instructions will result in an improperly installed
and operating appliance, voiding its warranty. Any change to this appliance and/or its
operating controls is dangerous.

6

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

General Information
900285-00 05/2015

WARNING

Clothing or other flammable material should not be placed on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à proximité.

WARNING

Improper installation or use of this appliance can cause serious injury or death from fire, burns,
explosion or carbon monoxide poisoning.

CAUTION

Hot while in operation. Do not touch. Severe Burns may result. Keep children, clothing
furniture, gasoline and other liquids having flammable vapors away.

ATTENTION

L’appareil est chaud lorsqu’il fonctionne. Ne pas toucher l’appareil. Risque de brûlures
graves. Surveiller les enfants. Garder les vêtements, les meubles, l’essence ou autres
liquides produisant des vapeur inflammables loin de l’appareil.

NOTE:

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this
appliance.

• For use with barrier(s) Part No(s). F1902 (33” Models), F1839 (35” Models), F1840 (40” Models), and
F1903 (45” Models). Follow installation instructions.

• These fireplaces are designed as supplemental heaters, and are not to be used as the primary heat source
when installed.

• Provide adequate clearances around air openings and adequate accessibility clearance for service and proper
operation. Never obstruct the front or back openings of the fireplace.

• These fireplaces are designed to operate on natural or propane gas only. The use of other fuels or combination of
fuels will degrade the performance of this system and may be dangerous.

• These fireplaces must not be connected to a chimney or flue serving a separate solid fuel burning fireplace.

• Only trim kit(s) supplied by the manufacturer shall be used in the installation of this fireplace.

Remarqué :

• Seules les trousses de garniture fournies par le fabricant doivent être utilisées pour l’installation de cet appareil.

7

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

INSTALLATION

PACKAGING

All models include

INTRODUCTION

General Information
900285-00 05/2015

The assembled vented gas fireplace heater is packaged with:

• Literature Kit (envelope in bottom compartment containing Installation and Operation Instructions (this manual),
and Safety-In-Operation Warning Labels)

• U-Shaped Vent Restrictor (attached to Literature Kit envelope)

• Hood (Inside firebox, Traditional Models)

• Log Set (Traditional Fireplaces, in firebox) or Glass Media (Contemporary Fireplaces)

• Volcanic Stone—1 bag (in bottom compartment, Traditional Models)

• Glowing Embers—1 bag (in bottom compartment, Traditional Models)

These vented gas fireplace heaters are sealed combustion, air-circulating gas fireplaces designed for residential and
commercial applications.

Millivolt fireplaces have a millivolt gas control valve with piezo ignition system. If a blower will be installed, electrical
power must be provided at the time of fireplace installation.

Electronic fireplaces are designed with an electronic intermittent pilot ignition system. External electrical power is
required to operate these units. In the event of a power outage, four (4) AA batteries (in battery holder) provide
backup power for fireplace operation. Battery backup will not operate optional/standard blower. Traditional units
require an additional four (4) AA batteries to provide power to the split-flow system.

NOTE: Installation and repair should be done by a qualified service person. The fireplace should be inspected before
use and at least annually by a professional service person. More frequent cleaning may be required due to excessive
lint from carpeting, bedding material, etcetera. It is imperative that control compartments, burners and circulating air
passageways of the fireplace be kept clean.

Remarqué : L’installation et la réparation devrait être confiées à un technicien qualifié. L’appareil devrait faire
l’objet d’une inspection par un technicien professionnel avant d’être utilisé et au moins une fois l’an par la suite.
Des nettoyages plus fréquents peuvent être nécessaires si les tapis, la literie, et cetera produisent une quantité
importante de pous-sière. Il est essentiel que les compartiments abritant les commandes, les brûleurs et les
conduits de circulation d’air de l’appareil soient tenus propres.

NOTE: Diagrams and illustrations are not necessarily shown to scale.

Approved Vent Components

These fireplaces are designed, tested and listed for operation and installation with the following vent
components only:

• Secure Vent® Direct-Vent System Components,

• Secure Flex® Flexible Vent Components, and

• Z-FLEX® Model GA Venting Systems listed to UL1777 and ULCS635 manufactured by Flexmaster
Canada Limited.

Use only the correct size venting (4 1/2” inner and 7 1/2” outer).
These approved vent system components are labeled for identification. DO NOT use any other manufacturer’s vent

components with these fireplaces.

Codes and Standards

These fireplaces comply with National Safety Standards and are tested and listed by PFS Corporation
(Report No. F13-094) to ANSI Z21.88 (in Canada, CSA-2.33), and CAN/CGA-2.17-M91 in both USA and Canada, as
vented gas fireplace heaters.

These fireplaces are listed for installation in bedrooms and manufactured homes.
The installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54—latest edition (In Canada, the current CAN/CGA-B149.1 installation code).
The fireplace, when installed, must be electrically grounded and wired in accordance with local codes or, in the

absence of local codes, with the National Electrical Code, ANSI/NFPA 70—latest edition, or the Canadian Electrical
Code, CSA C22.1—latest edition.

8

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

BTU Input

General Information
900285-00 05/2015

Table 1: Input Rate (BTU/HR), Gas Valves

Models

33” Models 14,000 10,500 13,000 9,500
35” Models 16,000 11,000 15,000 11,000
40” Models 20,000 14,000 19,000 14,000†
45” Models 21,500 13,500 21,500 13,500

† 12,000 in Superior Contemporary Models

High Rate Low Rate High Rate Low Rate

Natural Gas Propane Gas

Table 2: Thermal Efficiency (%)

Model

33” Models 65 60 65 63
35” Models 66 61 66 63
40” Models 66 61 66 63
45” Models 67 61 67 63

* AFUE is a measurement of the US Department of Energy, ** P4 (EnerGuide) is a measurement of the Canadian Office of Energy Efficiency.
Efficiencies are based on Normal input operation.

AFUE * P4 ** AFUE * P4 **

Millivolt Electronic

Gas Pressure

Table 3: Inlet Gas Supply Pressure

Fuel Minimum Maximum

Natural Gas 5” WC / (1.25 kPa) 10.5” WC / (2.61 kPa)

Propane 11.0” WC / (2.74 kPa) 13.0” WC / (3.23 kPa)

Table 4: Manifold Gas Supply Pressure

Fuel Traditional Model Pressure Contemporary Model Pressure

Natural Gas 3.5” WC / (0.87 kPa) 3.8” WC/ (0.95 kPa)

Propane 10.0” WC / (2.49 kPa) 9.8” WC (2.44 kPa)

Test gauge connections are provided on the front of the millivolt and electronic gas control valve (identified IN for the
inlet and OUT for the manifold side). The control valves have a 3/8” (10 mm) NPT thread inlet and outlet side of the
valve (Figure 1 and Figure 2).

Figure 1: Millivolt Gas Valve Figure 2: Electronic Gas Valves

ContemporaryTraditional

Propane tanks are at pressures that will cause damage to valve components. Verify that the tanks have step down
regulators to reduce the pressure to safe levels.

The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve during
any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

9

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Orifice Sizes—Sea Level to High Altitude

These fireplaces are tested and approved for installation at elevations of 0–4500 ft (0–1372 m) above sea level
using the standard burner orifice sizes (Table 5). For elevations above 4500 ft, contact your gas supplier or qualified
service technician.

Table 5: Burner Orifice Sizes, Elevation 0–4500 ft ( 0–1372 m)

Model

33” Models #49 (0.073”)* #57 (0.043”)*
35” Models #48 (0.076”)* #56 (0.046”)*
40” Models #44 (0.086”)* #55 (0.052”)*
45” Models #43 (0.089”)* #54 (0.055”)*

* Standard size installed at factory

Deration

At elevations above 4500 ft, the amount of BTU fuel value delivered must be reduced by either:

• Using gas that has been derated by the gas company.

• Changing the burner orifice to a smaller size as regulated by the local authorities having jurisdiction and by the
(USA) National Fuel Gas Code NFPA 54/ANSI Z223.1—latest edition or, in Canada, the CAN/CGA-B149.1 codes—
latest edition.

NOTE: Flame breadth, height and width will diminish 4% for every 1,000 ft of altitude.

IN CANADA—CAN/CGA-2.17-M91 (HIGH ALTITUDE):
THE CONVERSION SHALL BE CARRIED OUT BY A MANUFACTURER’S AUTHORIZED REPRESENTATIVE,

IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER, PROVINCIAL OR TERRITORIAL
AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN/
CGA-B149.1 OR CAN/CGA-B149.2 INSTALLATION CODES.

Natural Gas

drill size

Installation

900285-00 05/2015

Propane
drill size

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of Massachusetts if the following additional
requirements are met:

• Install this appliance in accordance with Massachusetts Rules and Regulations 248 C.M.R. Sections 4.00
through 8.00.

• Installation and repair must be done by a plumber or gas fitter licensed in the Commonwealth of Massachusetts.

• The flexible gas line connector used shall not exceed 36 inches (92 centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations installed less than seven (7) feet above the finished
grade must comply with the following additional requirements:

• A hard wired carbon monoxide detector with an alarm and battery back-up must be installed on the floor level
where the gas fireplace is installed. The carbon monoxide detector must comply with NFPA 720, be ANSI/UL
2034 listed and be ISA certified.

• A metal or plastic identification plate must be permanently mounted to the exterior of the building at a minimum height
of eight (8) feet above grade and be directly in line with the horizontal termination. The sign must read, in print size no
less than one-half (1/2) inch in size, GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks around your fireplace with noncombustible material and wherever cold
air could enter the room. It is especially important to insulate outside chase cavity between studs and under floor on
which fireplace rests, if floor is above ground level. Gas line holes and other openings should be caulked or stuffed
with unfaced fiberglass insulation.

10

NOTE: Do not use loose, or blown-in insulation in the cavity surrounding the fireplace.

If the fireplace is being installed on a cement slab in cold climates, a sheet of plywood or other raised platform can
be placed underneath to prevent conduction of cold transferring to the fireplace and into the room. It also helps to
seal inside surfaces and tape for maximum air tightness and caulk firestops.

Innovative Hearth Products

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes.

Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements
locaux le permettent.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for
use with other gases, unless a certified kit is used.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil ne
peut être converti à d’autres gaz, sauf si une trousse de conversion est utilisée.

Ensure that the cross members are not cut or weakened during installation. The structural
integrity of the manufactured home floor, wall, and ceiling / roof must be maintained.

This appliance must be grounded to the chassis of the manufactured home in accordance
with local codes or in the absence of local codes, with the National Electrical Code ANSI /
NFPA 70—latest edition or the Canadian Electrical Code CSA C22.1—latest edition.

Installation

900285-00 05/2015

CAUTION

CAUTION

LOCATION

In selecting the location, the aesthetic and functional use of the fireplace are primary concerns. However, vent
system routing to the exterior and access to the fuel supply are also important.

Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies.

En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a peu de
circulation et loin du mobilier et des tentures.

The location should also be free of electrical, plumbing or other heating/air conditioning ducting.
These direct-vent fireplaces are uniquely suited for installations requiring a utility shelf positioned directly above the

fireplace. Utility shelves like these are commonly used for locating television sets and decorative plants.

Be aware that this is a heat producing fireplace. Objects placed above the unit are exposed to elevated temperatures.
Do not insulate the space between the fireplace and the area above it.

The minimum height from the base of the fireplace to the underside of combustible materials used to construct a
utility shelf in this fashion is shown in Table 9 and Table 10.

Figure 3: Typical Locations and Venting

Top Vent

Top Vent

Rear Vent

Top Vent

Rear Vent

Horizontal Vent

(Rear Vent with chase)

Horizontal Vent

(Rear Vent without chase)

Recessed

Installation

Top Vent

Top Vent Top Vent

Vertical Vent

(Rear Vent)

Horizontal Vent

(Top Vent)

Vertical Vent

(Top Vent)

11

Innovative Hearth Products

12

X

Roof pitch is X/12

2 ft

minimum

2 ft minimum

Lowest

discharge

opening

H*

*H = minimum height from roof to

lowest discharge opening of vent

Horizontal overhang

Vertical

wall

Vent

termination

Storm collar

Concentric

vent pipe

Flashing

1” (25.4 mm) minimum
clearance to combustibles

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

VENT TERMINATION CLEARANCES

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting
according to local codes, these instructions, the current National Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA or
the current standards of CAN/CGA-B149.1 in Canada.

Vertical Vent Termination Clearances

Terminate multiple vent terminations according to the installation codes listed above and Figure 4.

Figure 4: Multiple Terminations

Terminate single vent caps relative to building components according to Table 6 and Figure 4.

Table 6: Termination Heights for Vents above Flat or Sloped Roofs (NFPA 54 / ANSI Z223.1)—Gas Vent Rule

12”

(305 mm)

minimum

Installation

900285-00 05/2015

6”

(153 mm)

Roof Pitch Termination Height *

Flat to 6/12 1.0 ft (0.3 m)
6/12 to 7/12 1.25 ft (0.38 m)
7/12 to 8/12 1.5 ft (0.46 m)
8/12 to 9/12 2.0 ft (0.61 m)

9/12 to 10/12 2.5 ft (0.76 m)
10/12 to 11/12 3.25 ft (0.99 m)
11/12 to 12/12 4.0 ft (1.22 m)
12/12 to 14/12 5.0 ft (1.52 m)
14/12 to 16/12 6.0 ft (1.83 m)
16/12 to 18/12 7.0 ft (2.13 m)
18/12 to 20/12 7.5 ft (2.29 m)
20/12 to 21/12 8.0 ft (2.44 m)

Horizontal Vent Termination Clearances

12

The horizontal vent termination must have a minimum of 6” (152 mm) clearance to any overhead combustible
projection of 2 1/2” (64 mm) or less (Figure 5). For projections exceeding 2 1/2” (64 mm) (Figure 5). For additional
vent location restrictions refer to Table 7.

All horizontal terminations may be located as close as 6” (152mm) to any (non-combustible and combustible)
exterior sidewall. This distance may be decreased to 2” (51mm) for noncombustible exterior sidewalls with all
approved terminations (Table 21).

Figure 5: Horizontal Vent Termination Clearances

*10” to center of termination for H1968

Combustible projection

2 1/2” or less in length

Combustible projection

greater than 2 1/2” in length

Ventilated

soffit - 18”

(457 mm)

Unventilated

soffit - 12”

(305 mm)

*

Termination kit

6

(152)

6”

Termination kit**

**Use 6.5”
from center of
termination for
all horzontal
terminations
applicable

Innovative Hearth Products

(TERMINATION PROHIBITED)

Inside Corner

Balcony with No Side

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Table 7: Horizontal vent termination clearances for buildings with combustible and noncumbustible exteriors

Outside Corner Recessed Location

D

E

V

B

L

C

F

V

B

TERMINATION CAP

V

Fixed

Closed

Openable

V

Openable

V

B

A

AIR SUPPLY INLET

X

Fixed

Closed

J

B

V

B

X

G

GAS METER RESTRICTED AREA

A Clearance above grade, veranda, porch, desk, or balcony 12” (300 mm) ** 12” (300 mm) *
B Clearance to window or door that may be opened 6” (150 mm)

C Clearance to permanently closed window 9” (229 mm)

D Vertical clearance to ventilated soffit located above the

termination within a horizontal distance of 18” (458 mm)

E Clearance to unventilated soffit 12” (305 mm) 12” (305 mm)

See Table 6

H

G

V

V

F

I

G

G

M

V

K

V

G

V

X

A

WallVBalcony with Perpendicular Side Wall

M

M

V

U.S. Installation ** Canadian Installation *

6” (150 mm)

for fireplaces < 10,000 Btu/h (3 kW),
9” (230 mm)

for fireplaces > 10,000 Btu/h (3 kW), and < 50,000 Btu/h

for fireplaces < 10,000 Btu/h (3 kW),
12” (300 mm)

for fireplaces > 10,000 Btu/h (3 kW)

(15 kW),
12” (300 mm)

for fireplaces > 50,000 Btu/h (15 kW) **

12” (305 mm)

recommended to prevent window condensation

recommended to prevent
window condensation

18” (458 mm) 18” (458 mm)

Installation

900285-00 05/2015

P

N

Q

O

V

F Clearance to outside corner 5” (127 mm)

minimum

5” (127 mm)
minimum

G Clearance to inside corner 6” (152 mm) minimum 6” (152 mm) minimum
H Clearance to each inside of center line extended above

meter / regulator assembly

36” (910 mm)
within a height of 15 ft above the meter / regulator assembly **

36” (910 mm)
within a height of 15 ft above the meter /
regulator assembly *

I Clearance to service regulator vent outlet 36” (910 mm)** 36” (910 mm)*

J Clearance to nonmechanical air supply inlet to building or

the combustion air inlet to any other fireplace

6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),

9” (230 mm)
for fireplaces > 10,000 Btu/h (3 kW) and < 50,000 Btu/h (15 kW),

6” (150 mm)
for fireplaces < 10,000 Btu/h (3 kW),

12” (300 mm)
for fireplaces > 10,000 Btu/h (3 kW)

12” (300 mm)
for fireplaces > 50,000 Btu/h (15 kW)**

K Clearance to a mechanical air supply inlet 36” (910 mm) above if within 10 ft (3 m) horizontally ** 72” (1830 mm) *
L Clearance above paved sidewalk or paved diveway located

84” (2130 mm) ‡ 84” (2130 mm) ‡

on public property

M Clearance under veranda, porch, deck or balcony 12” (300 mm) *‡ 12” (300 mm) *‡

N Depth of alcove (maximum) 72” (1830 mm) ** 72” (1830 mm) *
O Clearance to termination (alcove) 6” (15.2 mm) ** 6” (15.2 mm)*
P Width of alcove (minimum) 36” (910 mm) ** 36” (910 mm) *
Q Clearance to combustible above (alcove) 18” (457 mm) ** 18” (457 mm) *

*

In accordance with the current CSA-B149.1 National Gas And Propane Installation Code

**

In accordance with the curent ANSI Z223.1/NFPA 54 National Fuel Gas Codes

‡

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

*‡

Only permitted if veranda, porch, deck, or balcony is fully-open on a minimum two sides beneath the floor

13

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

MINIMUM CLEARANCES TO COMBUSTIBLES
Fireplace And Vent Clearances

The fireplace is approved with zero clearance to combustible materials on all sides (Table 8), with the following
exception: The unit may not be recessed (allowance made for mantel legs / side trim in (Figure 6). When the unit is
installed with one side flush with a wall, the wall on the other side of the unit must not extend beyond the front edge
of the unit (Figure 6).

Table 8: Minimum Clearances *

From Bottom of Unit to Ceiling 64” (1626 mm)

clearance immediately in front of viewing area(s)

* 3” (76 mm) above any horizontal/inclined vent component.
** See Page 21 for clearance requirements to the nailing flange located at each side of the unit and any screw heads adjacent to it.

Front Service Clearance—

Back

Sides

Top Standoffs 0” (0 mm) to top standoffs

Floor 0” (0 mm)

Vent

1” (26mm) to wrapper

0” (0 mm) to Spacers

1/2” (13 mm) to wrapper
0” (0 mm) to Spacers **

3” (76 mm)—Top *

1” (25.4 mm)—Sides and Bottom

36” (914 mm)

Installation

900285-00 05/2015

The fireplace must be mounted on a fully supported base extending the full width and depth of the unit. The fireplace
may be located on or near conventional construction materials. However, if installed on combustible materials, such
as carpeting, vinyl tile or other combustible material other than wood flooring, the appliance shall be installed on a
metal or wood panel extending the full width and depth of the appliance.

Hearth Extension

A hearth extension is not required with this fireplace. If a hearth extension is used, do not block the lower control
compartment door. Any hearth extension used is for appearance only and does not have to conform to standard
hearth extension installation requirements.

Shelf Height

To provide for the lowest possible shelf surface, use the rear vent model. For top vent models, the venting attached
to the top vent should be routed in a way to minimize obstructions to the space above the fireplace. Do not insulate
the space between the fireplace and the area above it (Table 9 and Table 10). The minimum height from the base
of the fireplace to the underside of combustible materials used to construct a utility shelf in this fashion is shown in

Table 9 and Table 10.

Table 9: Combustible Shelf Height—Top Vent

Top Vent with one 90° Elbow

Model

Secure Vent

33” Models 44” (1118 mm) 46” (1168 mm) 39” (990 mm)
35” Models 47” (1194 mm) 49” (1245 mm) 41” (1042 mm)
40” Models 52” (1321 mm) 54” (1372 mm) 46” (1169 mm)
45” Models 52” (1321 mm) 54” (1372 mm) 46” (1169 mm)

®

Secure Flex®

(flex elbow)

Alternative Rear Vent

applications*

Secure Vent

®

Shelf Height

(see table)

No com­bustibles or
insulation
in the
shaded area
between the
appliance
and the
shelf
above it.

14

Innovative Hearth Products

(152 mm)

mantel legs may

At 6 in. minimu
side wall clearance,
a combustible wal
can project to an
length

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Figure 6: Combustible Side Clearances Figure 7: Mantel Height

At 6” minimum
side wall
clearance, a
combustible
wall can project
to any length.

.

6 in.

6”

45

45

m

l

y

o

o

3 1/2”

3 1/2 in.

(89 mm)*

(89 mm)

Top View of

Top View of

Fireplace

Fireplace

Combustible materials

Combustible Materials
Allowed In Shaded Area

allowed in shaded area

“Safe Zone”

“Safe Zone”.

Combustible Walls

Combustible walls

shown in dark gray

shown in dark gray

Combustible

Combustible mantel

project beyond either side

legs may project

of the fireplace opening

beyond either side of

as long as they are kept
within the shaded area

the fireplace opening

illustrated here.

as long as they are kept
within the shaded area
illustrated here.

20 (508)

18 (457)

16 (406)

14 (356)

12 (305)

10 (254)

in. (mm)

12

(305)

Mantel depth

(203)

10

(254)

8

(152)

(152 mm)

* 6” (152 mm) in 35” and 40” Contemporary units

Traditional Contemporary

Wall Finishes / Surrounds / Mantels

Installation

900285-00 05/2015

Mantel depth

25 (635)

23 (584)
21 (533)

19 (483)

17 (432)

15 (381)

4

(102)

6

Hood

2

(51)

Fireplace

12

(305)

10

(254)

8

(203)

6

(152)

4

(102)

(51)

2

Fireplace
Opening

Fireplace

NOTE: Combustible wall finish materials and/or surround materials must not be allowed to encroach the area defined
by the fireplace front face (black sheet metal). Never allow combustible materials to be positioned in front of or

overlapping the fireplace face (Figure 40).

Non-combustible materials, such as surrounds and other fireplace trim, may be installed on the fireplace face, but they
must not cover any portion of the removable glass panel or control compartment.

Vertical installation clearances to combustible mantels vary according to the depth of the mantel (Figure 7). Mantels
constructed of non-combustible materials may be installed at any height above the fireplace opening. However, do
not allow anything to hang below the fireplace hood.

Minimum clearance requirements include any projections such as shelves, window sills, mantels, etc. above
the fireplace.

NOTE: To avoid heat-related finish damage, use finish materials rated 175 °F, or higher, on the underside of the mantel.

INSTALLATION PREPARATION

The fireplace is shipped with all gas controls and components installed and pre-wired. Before installing the fireplace,
follow these steps:

1. Remove the shipping carton, and retain the front of the carton (used to protect the fireplace during construction).

2. Remove the shipping pad, exposing the front glass door.

3. Remove the glass door (Page 61).
NOTE: Place the glass door on the shipping carton to protect its surface.

15

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

INSTALLATION SEQUENCE

The typical sequence of installation is outlined below; however, each installation is unique and may result in
variations to the steps described.

See the pages referenced in the following steps for detailed instructions.

Framing

1. Construct the Fireplace Framing (Page 16).

2. Prepare the Fireplace Top Spacers (Page 18).

3. Route the Gas Supply Line to the Fireplace (Page 18).

4. Determining Vent Setup in the Combination Venting Unit (Page 19)

5. Installing Metal, Non-Combustible Front Standoff (Page 19)

6. Rough in the Electrical Supply, if Needed (Page 20).

7. Install the [Optional] Blower Kit before Installation in the Framing (Page 20).

Venting

8. Place the Fireplace in the Framing and Secure (Page 21).

9. Select a Horizontal or Vertical Vent System (Page 21).

10. Install the Vent Restrictor (if necessary) (Page 22).

11. Install the Vent System (Page 25).

Electrical Connection

12. Complete the Field Wiring (Page 37).

13. Install the [Optional] Blower Kit after Installation in the Framing (Page 39).

Gas Connection

14. Connect the Gas Line (Page 40).

15. Verify Proper Fireplace Operation (Page 41).

Finishing

16. Optional: Install the Firebox Liners (Page 58).

17. Install the Logs, Volcanic Stone, and Glowing Embers or Glass Media (Page 58).

18. Install the Glass Door (Page 62).

19. Adjust the Air Shutter to Ensure Proper Flame Appearance (Page 42).

20. Install the Hood in Traditional Fireplaces (Page 43).

21. Reinstall the Included Barrier (Page 44).

22. Install the Finishing Materials and Facade in Contemporary Fireplaces (Page 44).

23. Attach the Safety-in-Operation Warning Labels (Page 47).

24. Installing Batteries for Backup and Wall Switch (Page 44).

Installation

900285-00 05/2015

1. Construct the Fireplace Framing

1. Frame the fireplace as illustrated in Table 10. For corner framing installations, use Table 11. All framing details

must allow for a minimum clearance to combustible framing members as shown in Table 8.

2. If the fireplace is to be elevated above floor level, a solid continuous platform must be constructed below the fireplace.
NOTE: Headers may be in direct contact with the fireplace top standoff spacers when they are bent up vertically,

maintaining the 4” clearance to the fireplace top, but must not be supported by them or notched to fit around them.
All construction above the fireplace must be self-supporting. DO NOT use the fireplace for structural support.

NOTE: For contemporary models, leave a minimum of 6” clearance to any side wall for proper facade installation and
fit.

16

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Table 10: Fireplace Framing Specifications

Model A * B C D E

33” Models

35” Models

40” Models

45” Models

33 3/4

(857)

35 3/8

(899)

40 3/8

(1026)

45 3/8

(1153)

34 1/4

(845)

36 1/4

(895)

41 1/4
(1048)

41 1/4
(1048)

36 7/8

(930)

38 3/4

(984)

43 3/4

(1111)
43 3/4

(1111)

14 1/2

(368)

18

(447)

18

(447)

18

(447 )

C = Minimum height of top vent installations
E = Minimum height of rear vent installations

* Minimum opening size; additional 1/8” per side is recommended.
NOTE: Framing specifications do NOT apply for flexible venting.

When using flexible venting, refer to the kit requirements for
framing specifications.

19 5/8

(499)

23 3/8

(594)

28 1/4

(717)

28 1/4

(717)

NOTE: Dimension “D” is the
required framing depth when
the finish material (drywall)
thickness is 1/2” (13mm).

Vent Framing—Top Vent

with One 90° Elbow

B

C

1/2 A

A

Inches (millimeters)

Installation

900285-00 05/2015

Framing
construction to be

10 1/2

2 x 4, or larger.

(267)

7 (178)

5 1/8
(130)

12 1/8

(308)

E

D

Table 11: Fireplace Framing Specifications—Corner Installation with Horizontal Termination

Model A B C D E F

33”

35”

40”

45”

33 3/4

(857)

35 3/8

(899)

40 3/8
(1025)

45 3/8
(1153)

51 1/4

(1302)

59 1/2

(1511)

63 13/16

(1621)

70 3/8

(1788)

36 1/4

(921)

42 1/16

(1068)

45 11/32

(1152)
49 3/4

(1264)

25 5/8

(651)

30 1/4

(768)

33 3/16

(818)

35 1/4

(895)

12 1/8

(308)

14 1/4

(362)

15 7/8

(403)

17 1/2

(445)

5 1/2
(140)

6 5/8
(168)

8 1/2
(216)

10 1/4

(260)

C

Back wall of chase/enclosure (including finishing materials)

Table 12: Fireplace Specifications

NOTE: When finishing the area around the hood, 5/8” clearance above hood is required for hood installation.

F

G

I

K

A

E

C

D

B

Blower

access panel

A

B

E

box access

Gas line

access

Hood

Junction

7
(178)

D

Inches
(millimeters)

H

Model A B C D (door) E F G H I J K

33” Models 30 1/8 (765) 26 1/4 (667) 18 5/16 (465) 30 1/2 (775) 33 5/8 (854) 21 7/8 (556) 10 15/16 (278) 31 (787) 5 3/4 (146) 14 (356) 8 1/2 (207)

35” Models 32 1/8 (816) 28 3/4 (730) 22 1/4 (565) 32 3/8 (822) 35 1/4 (895) 25 (635) 12 1/2 (317) 32 7/8 (835) 6 7/8 (175) 17 (432) 10 1/6 (256)

40” Models 37 1/8 (943) 33 1/4 (845) 27 1/4 (692) 37 3/8 (949) 40 1/4 (1022) 30 (762) 15 (381) 37 7/8 (962) 6 7/8 (175) 17 (432) 10 1/6 (256)

45”Models 37 1/8 (943) 33 1/4 (845) 27 1/4 (692) 42 3/8 (1076) 45 1/4 (1149) 35 (889) 17 1/2 (445) 42 7/8 (1089) 6 7/8 (175) 17 (432) 10 1/6 (256)

Top View Front View

Left Side View Right Side View

17

Innovative Hearth Products

TM

Superior

2.

DRT/C3000 Series Direct-Vent Gas Fireplaces

Prepare the Fireplace Top Spacers

1. The two (2) 4” standoff spacers on top of the fireplace cabinet are shipped flat. Remove the screw adjacent to

the detached end (Figure 8).

2. Bend the standoffs as shown (Figure 9):

3. Align the hole in the standoff with the hole in the fireplace top, and secure with the screw that was removed in
Step 1 (Figure 9).

Figure 8: Unassembled standoff Figure 9: Assembled standoffs

Positioned flat as shipped from the factory

Screw

Top Standoff

Configuration for 1/2" finish materials

Top Standoff

Installation

900285-00 05/2015

Configuration for 5/8" finish materials

Top Standoff

Fireplace Front

3. Route the Gas Supply Line to the Fireplace

1. Route a 1/2” (13 mm) gas line to the left side of the fireplace (Figure 10).

NOTE: Gas lines must be routed, assembled, and made of materials that are in strict accordance with local codes

and regulations. All fireplaces are factory-equipped with a flexible gas line connector and a 1/2” shutoff valve
(Page 40).

Figure 10: Routing the gas line - 35”, 40”,

45” Models

Left side front corner of
fireplace framing

Pipe coupling
(recommended)

7 5/8”
(195 mm)

3”

(76 mm)

Proper Sizing of Gas Line

Properly size and route the gas supply line from the supply regulator to the area where the appliance is to be installed
per requirements outlined in the National Fuel Gas Code, NFPA 54—latest edition (USA) or CAN/CGA-B149.1—
latest edition (Canada).

The gas supply line should not be connected to the appliance until step 14. Connect the Gas Line (Page 40).

Fireplace

Front

Figure10a: Routing the Gas Line - 33” Model

Figure 60: Routing the gas line

Left side front corner of
fireplace framing

Pipe coupling
(recommended)

5 1/4”
(140 mm)

3”

(76 mm)

Fireplace

Front

18

NOTE:

• All fireplaces are factory-equipped with a flexible gas line connector and 1/2” shutoff valve (Figure 35).

• See Massachusetts Horizontal Vent Requirements for additional requirements for installations in the state of
Massachusetts in the USA.

• A pipe joint compound rated for gas should be used on the threaded joints. Ensure propane-resistant
compounds are used in propane applications. Be very careful that the pipe compound does not get inside
the pipe.

• A sediment trap in the supply line as close as possible to the fireplace is recommended.

• Check with the local building official for local code requirements (e.g., Are below grade penetrations of the gas
line allowed?, etc).

CAUTION

If propane is used, be aware that with a tank that is too small (i.e., under 100 lbs, if this
is the only gas appliance in the dwelling—see NPFA 58), there may be a loss of pressure.
This can result in insufficient fuel delivery that can cause sooting, delayed ignition, or other
malfunctions. Any damage resulting from an improper installation is not covered by the
limited warranty.

Innovative Hearth Products

TM

Superior

4.

DRT/C3000 Series Direct-Vent Gas Fireplaces

Determining Vent Setup in the Combination Venting Unit

900285-00 05/2015

Combination venting units are shipped with rear venting setup nearly ready for install. If this is the type of vent you require, remove
all insulation packing and flue plug block off from rear venting and proceed with fireplace installation. If you require a top-vented
unit, use the following steps to convert the fireplace before use.

Outside preparation of the fireplace for top-vent conversion

Installation

Step 1: Remove the eight (8) screws holding the top vent cover

Step 2: Remove the round flue cover from the top venting outlet.

plate and gasket. Discard cover plate and reinstall screws.

Step 3: Remove insulation from inside flue pipe. Step 4: Make sure insulation disc is still in the round cover. Re-

move the flue plug from the top flue.

Installing Metal, Non-Combustible Front Standoff

5.

A non-combustible metal standoff is provided with the fireplace to prevent overlap of drywall or other material of portions of the
fireplace that may be prone to the buildup of heat. Standoff arrives on the lower front of the unit. A field-supplied, noncombustible
board may be substituted for the metal standoff.

Use raised locating dimples
to position front standoff.

Step 1: Carefully bend up the two (2) tabs on the heat shield at a 90° angle from each opposite
joint and then the foot of the Standoff at approximately a 45° angle.

Step 2: Secure all three of the screws to the up-right posi­tioned heat shield - one (1) at both ends and one (1) in the
center.

Step 3: Top of front standoff
should be flush with top
standoffs.

Step 4: Standoff should be
flush with front of unit.

19

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

Installing Non-Combustible Fireboard Standoff in 35” and 40” Contemporary Fireplaces

A non-combustible standoff board is provided for 35” and 40” Contemporary fireplaces to prevent overlap of drywall or other material
of portions of the fireplace that may be prone to the buildup of heat. It is supported by a middle bracket and two side brackets.

Separate and note metal side
(2) and center (1) brackets.

Step 2: Remove the three screws that align with the clearance
screwholes from the top of the unit. Secure the center bracket to
the top center of the fireplace

Rough in the Electrical Supply, if Needed

6.

Step 1: Remove two screws from the top and side of the unit. Bend the side bracket securing tab
over the edge of the unit and secure. Secure bracket to the top through the clearance screwhole.

Step 3: Top of front fireboard
standoff should be flush with
top standoffs (not shown).

As necessary, rough in the fireplace electrical supply per NEC and local codes.

7. Install the [Optional] Blower Kit before Installation in the Framing

1. Remove the left side blower cover panel screw, and blower cover panel in Table 12. Retain the panel and screw

for later reinstallation.

2. Slide the blower through the opening and position it with the bracket oriented to the front of the firebox and

the blower discharge to the rear of the firebox. Bend the two tabs in the firebox floor to secure the blower to
the floor.

3. Reinstall the blower cover panel and secure with the removed screw.

4. Access the blower supply wiring through the front of the fireplace and plug it into the junction box in the right,

rear of the fireplace (Figure 32).

5. Install the blower control switch according to its included instructions.

Step 4: Fireboard standoff
can be secured to the capture
screwholes.

20

Innovative Hearth Products

TM

Superior

8.

DRT/C3000 Series Direct-Vent Gas Fireplaces

Place the Fireplace in the Framing and Secure

NOTE: Nailing flanges, combustible members, and screw heads in areas directly adjacent to the nailing flanges are

EXEMPT from the 1/2” clearance to combustible requirements for the firebox outer wrapper.
NOTE: Combustible framing may be in direct contact with the nailing flanges and may be located within 1/2” of screw

heads and the firebox wrapper in areas adjacent to the nailing flanges.
Frame the opening to the exact dimensions specified in the framing details in this manual.

1. Bend out the appropriate nailing flanges for the drywall / finish material to be used (Figure 11). Nailing flanges
are provided for:

• flush framing,

• 1/2”, and

• 5/8” framing depths.

2. Secure the fireplace to the side framing members using the unit’s nailing flanges —one top and bottom on each
side of the fireplace front (Figure 11). Use 8d nails or the equivalent.

Figure 11: Nailing Flanges

Unit nailing flange

Side

framing

(no clearance to combustible
framing is required)

Installation

900285-00 05/2015

VENT SYSTEM PREPARATION

9. Select a Horizontal or Vertical Vent System

1. With the fireplace secured in the framing, determine the vent route and identify the exterior termination location.

The following sections describe vertical (roof) and horizontal (exterior wall) vent applications. Use only approved
vent components (Page 19 and Page 48).

NOTE: This fireplace must be vented directly to the outside.

The vent system may not service multiple appliances, and must never be connected to a
flue serving a separate solid fuel burning appliance.

NOTE: The vent pipe is tested to be run inside an enclosed wall (such as a chase). There is no requirement for

inspection openings in the enclosing wall at any of the joints in the vent pipe.

WARNING

21

Innovative Hearth Products

2 1/2”

Break-Away

1

3

20

40

6

10

40

25 ft Maximum

horizontal run (flat to near level)

60 ft Maximum vertical run

60

1.9

25

Horizontal Distance (ft)

Vertical Height (ft) from top of unit

Vertical Height (ft)

2

5

Elbow**

5 10

15

3” Base + wing3” Base

6 ft Minimum
vertical run

6 ft Minimum vertical run

None

Appliance Top Vent Outlet

U-Shaped Vent

Restrictor

Inner

Fireplace

Collar

Appliance Top Vent Outlet

U-SHAPED VENT

Appliance Rear

ent

U-Shaped Vent

Restrictor

Inner

Fireplace

Collar

Appliance Top Vent Outlet

U-SHAPED VENT
RESTRICTOR

APPLIANCE REAR

VENT OUTLET

INNER FIREPLACE

COLLAR

Inner Fireplace Collar Appliance Rear

Vent Outlet

U-Shaped Vent
Restrictor

Intake Air Baffle

With break-away
raised***

U-Shaped Vent

Restrictor

Inner

Fireplace

Collar

Appliance Top Vent Outlet

U-SHAPED VENT
RESTRICTOR

APPLIANCE REAR

VENT OUTLET

INNER FIREPLACE

COLLAR

Inner Fireplace Collar Appliance Rear

Vent Outlet

U-Shaped Vent
Restrictor

Intake Air Baffle

Base Vent Restrictor

With break-away
raised***

TM

Superior

10.

DRT/C3000 Series Direct-Vent Gas Fireplaces

Install the Vent Restrictor (if necessary)

Installation

900285-00 05/2015

1. Use the vent run descriptions in Figure 12 to determine if a vent restrictor is necessary.

2. If necessary, assemble the vent restrictor and wing as detailed in Figure 12 and Figure 15.

3. If necessary, install the appropriate vent restrictor (Figure 13 and Figure 14).

NOTE: If installing the vent restrictor in a rear vent application, ensure the factory-installed intake air baffle is in place (Figure 14).
NOTE: The vent restrictor is shipped in the firebox.

Figure 12: When to use a vent restrictor Figure 13: Vent restrictor installation, Top vent

U-Shaped Vent

*

Restrictor

Inner

Fireplace

Collar

* For straight runs or runs with elbows as illustrated in Vertical Vent Figures/Tables starting on
Page 28
** No rise required.

*** On 33” Models, use the 3” base restrictor. Do not raise the break-away tab.
NOTE: When venting Rear Horizontal with slip collar and termination only, install base vent

restrictor with the breakaway portion raised.

***

*

Figure 14: Vent restrictor installation, Rear vent

Inner Fireplace Collar

Inner Fireplace Collar

INNER FIREPLACE

COLLAR

Intake Air Baffle

Appliance Rear

APPLIANCE REAR

Vent Outlet

Vent Outlet

VENT OUTLET

U-Shaped V

U-Shaped Vent

Restrictor

Restrictor

RESTRICTOR

Figure 15: Vent restrictor assembly

With
break-away
raised***

Base Vent Restrictor

Base Vent Restrictor + Wing

22

Innovative Hearth Products

SV4.5E90

(90

°

Elbow)

8 1/8 in.

(206 mm)

Swivel Joint

(360

°

swivel)

4 13/16 in.

(122 mm)

SV4.5E45

(45

°

Elbow)

Swivel Joint

(360

°

swivel)

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Vent Restrictor with Horizontal Terminations

When horizontally terminating a vent system with a vertical vent run up to 4 ft through an exterior wall, no vent
restrictor is required.

If installing more than 4 ft of vertical venting, install the restrictor (Figure 14), from inside or outside the unit, in the
inner fireplace collar. The vent restrictor is held in place by friction.

Table 13: Effective Vent Length

Model Effective Length

SV4.5L6 4 1/2”
SV4.5L12 10 1/2”
SV4.5L24 22 1/2”
SV4.5L36 34 1/2”
SV4.5L48 46 1/2”

Connecting the vent pipe

Secure Vent® SV4.5 direct-vent system components are unitized concentric pipe components featuring positive twist
lock connections (Figure 16 and Figure 17). All of the fireplaces covered in this document are fitted with collars
having locking inclined channels. The dimpled end of the vent components fit over the fireplace/vent collar to create
the positive twist lock connection.

1. Align the dimpled end over the collar, adjusting the radial alignment until the four (4) locking dimples are aligned

with the inlet of the four (4) inclined channels on the collar (Figure 16).

2. Push the vent component against the collar until it fully engages, then twist the component clockwise, running

the dimples down and along the incline channels until they seat at the end of the channels.

Installation

900285-00 05/2015

Vent elbows

NOTE: The unitized design of the Secure Vent® components will engage and seal both the inner and outer vent pipe.

3. If desired, a #6 x 1/2” screw can be used at the joint, but is not required as the pipe will securely lock

when twisted (Figure 17).

Where required, a telescopic vent section (SV4.5LA) may be used to provide the installer with an option to install
in tight and confined spaces, or where the vent run made up of fixed length pieces develops a joint in a undesirable
location, or will not build up to the required length. The SV4.5LA Telescopic Vent Section has an effective length of
from 1 1/2–7” (38–191 mm). The SV4.5LA is fitted with a locking inclined channel end (identical to a normal vent
section component) and a plain end with three (3) pilot holes. Slip the plain end over the locking channel end of a
standard SV4.5 vent component the required distance and secure with three (3) screws.

Figure 16: Connecting vent

components

Arrow

Dimple

Locking
Incline
Channel

Appliance Collar or
Vent Section

Figure 17: Connected vent

components

Dimple

Locking

Incline

Channel

Arrow

Figure 18: Elbow Dimensions

4 13/16”
(122 mm)

Swivel Joint

(360°)

SV4.5E45

(45° elbow)

Swivel Joint

(360°)

SV4.5E90

(90° elbow)

8 1/8”
(206 mm)

Vent elbows are available in 90° and 45° configurations. Refer to Figure 18 for the SV4.5E45 and SV4.5E90
elbow dimensions. The elbows feature a twist section to allow them to be routed about the center axis of their initial
collar section to align with the required direction of the next vent run element.

1. Rotate the elbow in a clockwise direction (to avoid the possiblity of unlocking any of the previously connected
vent sections) for proper alignment (Figure 18). See Connecting the vent pipe for more information.

23

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Vent section length table

Table 14: Vent Section Length

Nominal Section

Length (in.)

Net Section Length

(in.)

Height of Vent

in. ft in. ft

4.5 0.375 1 0 0 0 0 1 252 21 0 1 0 7 0 8

9 0.75 2 0 0 0 0 2 276 23 0 0 0 8 0 8

10.5 0.875 0 1 0 0 0 1 279 23.25 0 0 0 0 6 6

15 1.25 1 1 0 0 0 2 280.5 23.375 1 0 0 8 0 9

22.5 1.875 0 0 1 0 0 1 289.5 24.125 0 1 0 0 6 7

31.5 2.625 0 3 0 0 0 3 301.5 25.125 0 0 1 0 6 7

34.5 2.875 0 0 0 1 0 1 310.5 25.875 0 0 0 9 0 9

37.5 3.125 1 1 1 0 0 3 325.5 27.125 0 0 0 0 7 7

43.5 3.625 0 2 1 0 0 3 330 27.5 1 0 0 0 7 8

45 3.75 0 0 2 0 0 2 345 28.75 0 0 0 10 0 10

46.5 3.875 0 0 0 0 1 1 349.5 29.125 1 0 0 10 0 11

51 4.25 1 0 0 0 1 2 372 31 0 0 0 0 8 8

55.5 4.625 0 1 2 0 0 3 379.5 31.625 0 0 0 11 0 11

57 4.75 0 0 1 1 0 2 418.5 34.875 0 0 0 0 9 9

67.5 5.625 0 0 3 0 0 3 465 38.75 0 0 0 0 10 10

69 5.75 0 0 0 2 0 2 475.5 39.625 0 1 0 0 10 11

73.5 6.125 1 0 0 2 0 3 480 40 1 1 0 0 10 12

79.5 6.625 0 1 0 2 0 3 492 41 1 0 1 0 10 12

81 6.75 0 0 0 1 1 2 499.5 41.625 0 0 0 1 10 11

91.5 7.625 0 0 2 0 1 3 504 42 1 0 0 1 10 12

93 7.75 0 0 0 0 2 2 511.5 42.625 0 0 0 0 11 11

97.5 8.125 1 0 0 0 2 3 520.5 43.375 0 2 0 1 11 14

103.5 8.625 0 0 0 3 0 3 531

108 9 1 0 0 3 0 4 538.5 44.875 1 0 0 2 11 14

117 9.75 1 0 5 0 0 6 549 45.75 1 0 2 1 11 15

118.5 9.875 1 1 0 3 0 5 558 46.5 0 0 0 0 12 12

126 10.5 0 0 1 3 0 4 562.5 46.875 1 0 0 0 12 13

130.5 10.875 1 0 1 3 0 5 568.5 47.375 0 1 0 0 12 13

135 11.25 0 0 6 0 0 6 573 47.75 1 1 0 0 12 14

139.5 11.625 0 0 0 0 3 3 580.5 48.375 0 0 1 0 12 13

142.5 11.875 1 0 0 4 0 5 589.5 49.125 0 1 2 2 10 15

144 12 1 0 0 0 3 4 595.5 49.625 1 1 1 0 12 15

154.5 12.875 1 1 0 0 3 5 604.5 50.375 0 0 0 0 13 13

160.5 13.375 0 2 0 0 3 5 615 51.25 0 1 0 0 13 14

172.5 14.375 0 0 0 5 0 5 625.5 52.125 0 2 0 0 13 15

177 14.75 1 0 0 5 0 6 631.5 52.625 1 0 1 0 13 15

186 15.5 0 0 0 0 4 4 637.5 53.125 0 1 1 0 13 15

196.5 16.375 0 1 0 0 4 5 651 54.25 0 0 0 0 14 14

207 17.25 0 0 0 6 0 6 655.5 54.625 1 0 0 0 14 15

211.5 17.625 1 0 0 6 0 7 672 56 0 2 0 0 14 16

217.5 18.125 0 1 0 6 0 7 678 56.5 1 0 1 0 14 16

229.5 19.125 0 0 1 6 0 7 688.5 57.375 1 1 1 0 14 17

232.5 19.375 0 0 0 0 5 5 697.5 58.125 0 0 0 0 15 15

241.5 20.125 0 0 0 7 0 7 702 58.5 1 0 0 0 15 16

246 20.5 1 0 0 7 0 8 712.5 59.375 1 1 0 0 15 17

24

Installation

900285-00 05/2015

Table 15 will assist calculating how many vent sections are needed for the planned vent configuration. When a vent
section is engaged with another section, its effective length will be 1 1/2” shorter.

6 12 24 36 48

4.5 10.5 22.5 34.5 46.5 Net Section Length (in.) 4.5 10.5 22.5 34.5 46.5

Number of Vent Sections

Nominal Section Length

Total Qty

(in.)

Height of Vent

44.25 0 2 2 0 11 15

720 60 0 0 1 0 15 16

6 12 24 36 48

Number of Vent Sections

Total Qty

Innovative Hearth Products

SV4.5CGV-1

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Clearance to combustibles

Maintain the minimum clearance to combustibles (e.g., framing, attic, ceiling insulation, etc.).
For all vertical runs:

• 1” (25 mm) from all sides

NOTE: Attic insulation shield (H3907, see Page 45) must be installed when blown or loose-fill insulation is used,
and is required for all attic installations.

For all horizontal/inclined runs:

• 3” (76 mm) from the top

• 1” (25 mm) from the sides

• 1” (25 mm) from the bottom

11. Install the Vent System

Install the Vertical Termination Vent System

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting
according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the
current standards of CAN/CGA-B149.1 in Canada.

Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier.

Dégagement conforme aux codes d’installa tion locaux et aux exigences du foumisseunde gaz.

Vertical vent systems terminate through the roof. The minimum vent height above the roof and/or adjacent walls
is specified in ANSI Z223.1 (In Canada, the current CAN/CGA-B149.1 installation code) by major building codes.
Always consult your local codes for specific requirements. A general guide to follow is the gas vent rule (Table 6).

The following figures and their associated vertical vent tables illustrate the various configurations that are possible
for use with these fireplaces. Secure Vent® pipe is shown in these figures; Secure Flex® pipe may also be used.
A table summarizes each configuration’s minimum and maximum vertical and horizontal length parameters for a
variety of applications.

1. Refer to Figure 25 and Table 17–Table 20 on Page 28–29 to select the type of vertical installation desired.
Elbows are available in 90° and 45° configurations. Refer to Figure 18 on Page 23 for the SV4.5E45 and
SV4.5E90 elbow dimensional specifications.

Installation

900285-00 05/2015

Vertical (Straight) Installation

1. Determine the number of straight vent sections required—See Effective Vent Length on Page 23 for more
information. Plan the vent lengths so that a joint does not occur at the intersection of ceiling or roof joists.

Figure 19: Vertical (Straight) Installation

Termination

Max. 60 ft
(18.3 m)

SV4.5FA or
SV4.5FB Flashing
AND SV4.5SC
Storm Collar

1” (25.4 mm)
Minimum
Clearance to
Combustibles

SV4.5VF
Firestop/Spacer*

*When using Secure Flex,
use Firestop/Spacer

SF4.5VF.

SV4.5L6/12/24/36/48
Vent Sections

25

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Vertical (Offset) Installation

1. Analyze the vent route and determine the number of vent sections and elbows required—See Effective Vent
Length on Page 23 for more information. Plan the venting so that a joint does not occur in the ceiling or roof
joists. Allow for elbows (Figure 18). Maintain the minimum clearances for combustibles (Page 25).

2. Frame the ceiling opening—Use a plumb line from the ceiling above the fireplace to locate the center of the

vertical run. Cut and/or frame an opening, 10 1/2 x 10 1/2” (267 x 267 mm) inside dimensions, about this center
mark (Figure 20).

Figure 20: Framing the ceiling opening

10 1/2” (267 mm) minimum

Roof
Framing

minimum 10 1/2 in.
(267 mm)

10 1/2” (267 mm)

minimum 10 1/2 in.
(267 mm)

minimum

Installation

900285-00 05/2015

Ceiling
Framing

Plumb Bob

3. Attach the vent components to the fireplace—See Connecting the vent pipe on Page 23.

4. Attach the vent components to each other—See Connecting the vent pipe on Page 23.

5. Install firestop/spacer at ceiling—When using Secure Vent®, use SV4.5VF firestop/spacer at ceiling joists; when

using Secure Flex®, use SF4.5VF firestop/spacer. If there is living space above the ceiling level, the firestop/
spacer must be installed on the bottom side of the ceiling. If attic space is above the ceiling, the firestop/spacer
must be installed on the top side of the joist. Route the vent sections through the framed opening and secure the
firestop/spacer with 8d nails or other appropriate fasteners at each corner.

Remember to maintain 1” (25 mm) clearance to combustibles, framing members, and attic or ceiling insulation
when running vertical chimney sections.

NOTE: The gap between the vent pipe and a vertical firestop can be sealed with non-combustible caulking.
NOTE: Attic Insulation Shield (H3907) must be installed when blown or loose-fill insulation is used, and is

required for all attic installations.

6. Support the vertical vent run sections—Support the vertical portion of the venting system every 8 ft (2.4 m)
above the fireplace vent outlet. One method of support is by utilizing field provided support straps (conventional
plumber’s tape). Secure the plumber’s tape to the framing members with nails or screws. Loop the tape around
the vent, securing the ends of the tape to the framing. If desired, sheet metal screws #6 x 1/2” length may be
used to secure the support straps to the vent pipe (Figure 21).

NOTE: Proper venting support is very important.

26

Figure 21: Supporting the Vertical Vent Run

Blocking

Support straps
(plumber’s tape)

8 ft (2.4 m)

maximum

1/2” (12.7 mm)
minimum
clearance to
combustibles

7. Change vent direction of horizontal/inclined run—Install the SV4.5E45 and SV4.5E90 elbows in the same
manner as the straight vent sections. See Vent elbows on Page 23 for more information.

Innovative Hearth Products

C

D

Storm
Collar

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

8. Continue installation of horizontal/inclined sections—Continue with the installation of the straight vent
sections in horizontal/inclined run. Install support straps every 5 ft (1.52 m) along horizontal/inclined vent runs
using conventional plumber’s tape.

Rise per foot run ratios are acceptable all the way to level. For best results, maintain the horizontal/inclined run in
a straight (no dips), slightly elevated plane of approximately 1/4” per 1 ft (20 mm per 1 m).

Maintain the required clearances to combustibles (Page 25).

9. Frame the roof opening—Identify the location for the vent at the roof. Cut and/or frame opening (Table 15).

Table 15: Roof Framing Dimensions

Pitch C D

0/12 10 1/2” (267 mm) 10 1/2” (267 mm)
6/12 10 1/2” (267 mm) 12” (305 mm)

12/12 10 1/2” (267 mm) 17 3/4” (451 mm)

10. Install the roof flashing—Extend the vent sections through the roof structure. Install the roof flashing over the
vent section and position such that the vent column rises vertically (use carpenters level). Nail along perimeter
to secure flashing or adjust roofing to overlap the flashing edges at top and sides only and trim where necessary.
Seal the top and both sides of the flashing with waterproof caulking.

11. Install the storm collar—Install the storm collar, supplied with the flashing, over the vent/flashing joint
(Figure 22). Loosen the storm collar screw. Slide collar down until it meets the top of the flashing. Tighten the
adjusting screw. Apply non-combustible caulking or mastic around the circumference of the joint to provide a
water tight seal.

Figure 22: Installing the Storm Collar Figure 23: Installing the Vertical Termination

12. Install the vertical termination—The final step involves installation of the SV4.5CGV-1 vertical termination.
Extend the vent sections to the correct height (Table 6 and Figure 4). The SV4.5CGV-1 Vertical Termination
(Figure 23) installs in the exact same fashion as any other Secure Vent

®

section. Align the termination over
the end of the previously installed section, adjusting the radial alignment until the four (4) locking dimples of
the termination are aligned with the inlets of the four (4) incline channels of the last vent section. Push the
termination down until it fully engages, then twist the termination clockwise running the dimples down and along
the incline channels until they seat at the end of the channels.

If the vent system extends more than 5 ft (1.5 m) above the roof flashing, stabilizers may be necessary.
Additional screws may be used at section joints for added stability. Guide wires or roof support assemblies may
be attached to the joint for additional support on multiple joint configurations.

27

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Vertical Vent Figures/Tables

Installation

900285-00 05/2015

NOTE: Secure Vent® rigid vent pipe is shown in the figures; Secure Flex® flexible vent pipe may also be used.
NOTE: Rise per foot run ratios are acceptable all the way to level. For best results, maintain the horizontal/inclined

run in a straight (no dips), slightly elevated plane of approximately 1/4” per 1 ft (20 mm per 1 m).
NOTE: SV4.5VF (Secure Vent), SF4.5VF (Secure Flex) firestop/spacer must be used anytime vent pipe passes

through a combustible floor or ceiling. SV4.5HF (Secure Vent), SF4.5HF (Secure Flex)firestop/spacer must be used
anytime vent pipe passes through a combustible wall.

NOTE: Two (2) 45° elbows may be used in place of one (1) 90° elbow. The same rise to run ratios, as shown in the
venting figures for 90° elbows, must be followed if 45° elbows are used.

WARNING

Do NOT join separate sections of concentric flexible vent pipe.

Figure 24: Top Vent—Straight Table 16: Rear Vent—One 90° Elbow

Ceiling firestop/
spacer SV4.5VF *

When using Secure Flex®,

*

use ceiling firestop/spacer
SF4.5VF.

V

Ceiling

firestop/

spacer

SV4.5VF *

Install the U-shaped vent restrictor in any vent run with more than
6 ft of vertical rise. See Page 22 for more information.

60 ft (18.3 m)

maximum

When using

*

Secure Flex®,
use ceiling
firestop/spacer
SF4.5VF.

Minimum 6 ft and maximum of 60 ft of vertical venting.

H

H Maximum V Minimum

feet meters feet meters

2 0.610 1 0.305

4 1.219 2 0.610

6 1.829 3 0.914

8 2.438 4 1.219

V + H = 60 ft (18.3 m) maximum
H = 8 ft (2.4 m) maximum
Install the U-shaped vent restrictor in any vent run with more than

6 ft of vertical rise. See Page 22 for more information.

If 8 ft of (H) horizontal vent run is needed, then 4 ft
(straight section) minimum of (V) vertical vent will be
required.

This table shows a 1 (V) to 2 (H) ratio. For every 1 ft of
(V) vertical, you are allowed 2 ft of (H) horizontal run,
up to a maximum horizontal run of 8 ft.

Minimum 6 ft of vertical venting.

28

Innovative Hearth Products
Superior

TM

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Table 17: Top Vent—Two 90° Elbows Table 18: Rear Vent—Three Elbows Table 19: Top Vent—Three Elbows

Installation

H

Ceiling firestop/
spacer SV4.5VF *

V1

When using Secure Flex®, use

*

ceiling firestop/spacer SF4.5VF.
When using Secure Flex, use

**

wall firestop/spacer SF4.5HF.

H Maximum V Minimum

feet meters feet meters ft m ft m ft m feet meters feet meters

5 1.524 Elbow Only 5 1.524 2 0.610 1 0.305 5 1.524 Elbow Only
5 1.524 1 0.305 10 3.048 4 1.219 2 0.610 5 1.524 1 0.305

10 3.048 2 0.610 15 4.572 6 1.829 3 0.914 10 3.048 2 0.610

15 4.572 3 0.914 20 6.096 8 2.438 4 1.219 15 4.572 3 0.914

25 7.62 5 1.524 H = 8 ft (2.4 m) maximum

+ H = 60 ft (18.3 m) maximum

V + V

1

H = 25 ft (7.62 m) maximum
Install the U-shaped vent restrictor in any vent run

with more than 6 ft of vertical rise. See Page 22
for more information.

If 25 ft of (H) horizontal vent run is needed,
then 5 ft (straight section) minimum of
(V) vertical vent will be required.

This table shows a 1 (V) to 5 (H) ratio. For
every 1 ft of (V) vertical, you are allowed
5 ft of (H) horizontal run, up to a maximum
horizontal run of 25 ft.

Minimum 6 ft and maximum of 60 ft of
vertical venting.

Wall firestop/
spacer SV4.5HF **

V1

V

H + H

Maximum

H + H1 = 20 ft (6.1 m) maximum
V + V1 + H + H1 = 60 ft (18.3 m) maximum

Install the U-shaped vent restrictor in any vent run
with more than 6 ft of vertical rise. See Page 22
for more information.

If 20 ft of (H) horizontal vent run is needed,
then 4 ft (straight section) minimum of
(V) vertical vent will be required.

This table shows a 1 (V) to 5 (H) ratio. For
every 1 ft of (V) vertical, you are allowed
5 ft of (H) horizontal run, up to a maximum
horizontal run of 20 ft.

NOTE: The vent system may have a
maximum of three (3) 90° elbows.

H1

Ceiling
firestop/spacer
SV4.5VF *

Wall firestop/
spacer
SV4.5HF **

V

V

1

H Maximum V Minimum H + H1 Maximum V Minimum

Minimum 6 ft of vertical venting.

When using

*

Secure Flex®, use
ceiling firestop/
spacer SF4.5VF.
When using

**

Secure Flex, use
wall firestop/
spacer SF4.5HF.

Ceiling
firestop/spacer
SV4.5VF *

H

Ceiling

V1

When using Secure Flex®, use

*

ceiling firestop/spacer SF4.5VF.
When using Secure Flex, use

**

wall firestop/spacer SF4.5HF.

20 6.096 4 1.219

H + H1 = 20 ft (6.1 m) maximum
V + V1 + H + H1 = 60 ft (18.3 m) maximum

Install the U-shaped vent restrictor in any vent
run with more than 6 ft of vertical rise. See
Page 22 for more information.

firestop/spacer
SV4.5VF *

H

H1

Wall firestop/
spacer
SV4.5HF **

If 20 ft of (H) horizontal vent run is
needed, then 4 ft (straight section)
minimum of (V) vertical vent will be
required.

This table shows a 1 (V) to 5 (H) ratio.
For every 1 ft of (V) vertical, you are
allowed 5 ft of (H) horizontal run, up to a
maximum horizontal run of 20 ft.

NOTE: The vent system may have a
maximum of three (3) 90° elbows.

Minimum 6 ft and maximum of 60 ft of
vertical venting.

V

29

Innovative Hearth Products

Support

Building

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Install the Horizontal Termination Vent System

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting
according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the
current standards of CAN/CGA-B149.1 in Canada.

Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier.

Dégagement conforme aux codes d’installa tion locaux et aux exigences du foumisseunde gaz.

Horizontal vent systems terminate through an outside wall. Building Codes limit or prohibit terminating in
specific areas (Table 7).

The following figures and their associated horizontal vent tables illustrate the various configurations that are possible
for use with these fireplaces. Secure Vent
A table summarizes each configuration’s minimum and maximum vertical and horizontal length parameters for a
variety of applications. For more information on connecting the vent pipe, see Page 23.

Figure 25: Typical Horizontal Vent Installation

900285-00 05/2015

®

pipe is shown in these figures; Secure Flex® pipe may also be used.

Installation

30

SV4.5E90

Elbow

Rise

Brackets

Ceiling

Firestop/Spacer

Vertical Vent

Fireplace

Horizontal / Inclined Run

SV4.5L6/12/24/36/48

Vent Sections

Support bracket spacing
every 5 ft (1.52 m)

90˚ elbow only

Termination

with firestop

Exterior
Wall

Termination

with firestop

Support

Framing

ertical

V

1. Analyze the vent route and determine the number of vent sections and elbows required—See Effective Vent
Length on Page 23 for more information. Plan the venting so that a joint does not occur in the ceiling or roof
joists. Allow for elbows (Figure 18). Maintain the minimum clearances for combustibles (Page 15).

2. Frame the exterior wall opening—Locate the center of the vent outlet on the exterior wall (Table 11). Cut and/

or frame an opening, 10 1/2 x 12 1/8” (267 x 308 mm) inside dimensions, about this center.

3. Frame the ceiling opening—If the vertical route is to penetrate a ceiling, use plumb line to locate the center
above the fireplace. Cut and/or frame an opening, 10 1/2 x 10 1/2” (267 x 267 mm) inside dimensions, about
this center (Figure 20).

4. Attach the vent components to the fireplace—See Connecting the vent pipe on Page 23.

5. Attach the vent components to each other—See Connecting the vent pipe on Page 23.

6. Install the firestop/spacer at the ceiling—When using Secure Vent®, use SV4.5VF firestop/spacer at ceiling

joists; when using Secure Flex®, use SF4.5VF firestop/spacer. If there is living space above the ceiling level,
the firestop/ spacer must be installed on the bottom side of the ceiling. If attic space is above the ceiling, the
firestop/spacer must be installed on the top side of the joist. Route the vent sections through the framed opening
and secure the firestop/spacer with 8d nails or other appropriate fasteners at each corner.

Maintain 1” (25 mm) clearance to combustibles, framing members, and attic or ceiling insulation when running
vertical chimney sections.

7. Support the vertical run sections—On the vertical run, support the venting system every 8 ft (2.4 m) above the
fireplace vent outlet with field provided support straps (Plumber’s tape). Attach the straps to the vent pipe and
secure to the framing members with nails or screws (Figure 26).

8. Change vent direction—At transition from or to a horizontal/inclined run, install SV4.5E45 or SV4.5E90 elbows
in the same manner as the straight vent sections. The elbows feature a twist section to allow them to be routed
about the center axis of their initial collar section to align with the required direction of the next vent run element.
Twist elbow sections in a clockwise direction only so as to avoid the possiblity of unlocking any of the previously
connected vent sections (Figure 18).

9. Continue installation of horizontal/inclined sections—Continue with the installation of the straight vent
sections in horizontal/inclined run. Install support straps every 5 ft. (1.52 m) along horizontal/inclined vent
runs using conventional plumber’s tape (Figure 25). Maintain the horizontal/inclined run in a straight (no dips),

Innovative Hearth Products

Firestop/Spacer (SV4.5HF) shown
on the exterior side of the wall. It

may also be installed on the

interior side.

Typical

Termination

Shown

7 in.

(178)

5 1/8 in.

(130 mm)

12 1/8 in.

(308 mm)

Note: Centerline of Vent Piping is

NOT the Same as the Centerline of

the Frame Opening.

6 to 48 in. Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

Base of Appliance

3 in.

(76 mm)

1 in.

(25.4 mm)

Adapter

SV4.5RCH

10 1/2 in.
(267 mm)

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

slightly elevated plane. The recommended incline is approximately 1/4” per 1 ft (20 mm per 1 m) horizontal, in
a direction away from the fireplace. Smaller rise per foot run ratios are acceptable all the way to at or near
level. Use a carpenter’s level to measure from a constant surface and adjust the support straps as necessary.

Maintain the required clearances to combustibles (Page 15).

10. Assemble the vent run to the exterior wall—If not previously measured, locate the center of the vent at the
exterior wall. Prepare the opening. Assemble the vent system until the terminus of the last section is within
7” (178 mm) to 11 1/4” (286 mm) inboard of the exterior surface to which the SV4.5 HT termination is to be
attached (Figure 27). If the terminus of the last section is not within this distance, use the telescopic vent section
SV4.5LA, as the last vent section. Table 21 lists the additional venting components needed (in addition to the
termination and adaptor) for a range of wall thicknesses.

11. Attach the termination adaptor—Attach the adaptor (SV4.5RCH, provided with the termination) to the vent
section or telescoping vent section, elbow or fireplace collar (Figure 27).

12. Install the firestop/spacer at the exterior wall—When using the square termination, install SV4.5HF (Secure
Vent), SF4.5HF (Secure Flex) Firestop/Spacer over the opening at the exterior side of the framing, long side up,
with the 3” spacer clearance at the top (Figure 27) and nail into place.

NOTE: The firestop/spacer may also be installed over the opening at the interior side of the framing.

13. Install the termination (SV4.5HT-2 or SV4.5HTSS)—From outside the exterior wall, slide the collars of the

termination onto the adaptor (the outer over the outer and the inner inside the inner) until the termination seats
against the exterior wall surface to which it will be attached. Orient the housing of the termination with the arrow
pointed upwards. Secure the termination to the exterior wall. The horizontal termination must not be recessed
into the exterior wall or siding by more than the 1 1/4” (32 mm) (Figure 28).

NOTE: If the venting exits the building below grade, or close to grade, see Installation Accessories on
Page 48 for available snorkel terminations. The termination must be above grade and above the expected
level of snow accumulation.

NOTE: The vent termination is hot while in operation and for a period of time following the use of the fireplace.

To prevent contact with hot surfaces, use a horizontal termination guard; available for purchase at your
local dealer.

The horizontal terminations have been designed to perform in a wide range of weather conditions. Our
terminations meet or exceed industry standards.

When selecting the locations of your horizontal terminations, do not place the termination where water from
eaves and adjoining rooflines may create a heavy flow of cascading water onto the termination cap. If the cap
must be placed where the possibility of cascading water exists, it is the responsibility of the builder to direct the
water away from the termination cap by using gutters or other means.

Take care to carefully follow the installation instructions for the termination, including the use of silicone caulking
where required.

Figure 26: Installing the Horizontal Termination

*

*Recommended IHP termination kit: H1968
**With termination kit only, 6-9 1/4”

**

See Table 11 for the minimum distance

to the base of the fireplace.

31

Innovative Hearth Products

Siding

Stucco

1-1/4” Maximum Recess of
the Square Termination into
Exterior Finishing Material

Exterior Surface of

Framing

6 in. to 9 1/4”

(152 to 235 mm)**

Exterior Surface of Siding

Interior Surface of

Finished Wall

Maximum wall thickness

9 1/4” (235 mm)**

Maximum Extent of
Vent Run Sections
Relative to Exterior
Surface of Framing

Last Vent Section. Use
Telescopic Vent
Section (SV4.5LA), If
Necessary

Adapter

SV4.5RCH

*Use silicone caulking to
seal the top and sides of
the termination, up to the
underlayment, stucco, or
masonry wall surface.

*Caulk

*Caulk

SV4.5HT-2

Square Termination

Shown

SV4.5HT-2

Square Termination

Shown

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

Figure 26: Installing the Horizontal Termination

NOTE: To help minimize water infiltration install the firestop/spacer (SV4.5HF) on the exterior side of the wall. The
firestop may be caulked with mill base caulk (such as 10K81) or high-temperature silicone.

Figure 27: Venting Connection and Exterior Wall Recessing of the Horizontal Termination

32

** For thicknesses greater

than 10” (254 mm) see

Table 21.

Innovative Hearth Products

H = 28 in. (711 mm) Maximum

.

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Horizontal Vent Figures/Tables

Installation

900285-00 05/2015

Table 20: Venting Components Required for Various Exterior Wall Thicknesses, when using Typical Termination Kits

Vent Components Required Exterior Wall Thickness

Termination Kit Only 6–9 1/4” (152–235 mm)

Termination Kit and 6” Vent Section (SV4.5L6) 10 3/4–14” (273–356 mm)

Termination Kit and 12” Vent Section (SV4.5L12) 16 3/4–20” (426–508 mm)

Termination Kit and Telescopic Section (SV4.5L12) 11 3/4–20” (299–508 mm)

NOTE: Secure Vent® rigid vent pipe and terminal are shown in the figures. Secure Flex® flexible vent pipe and
terminal may also be used.

NOTE: Two (2) 45° elbows may be used in place of one (1) 90° elbow. The same rise to run ratios, as shown in the
venting figures for 90° elbows, must be followed if 45° elbows are used.

NOTE: Maintain the horizontal/inclined run in a straight (no dips), slightly elevated plane. The recommended incline
is approximately 1/4” per 1 ft (20 mm per 1 m) horizontal, in a direction away from the fireplace. Smaller rise per
foot run ratios are acceptable all the way to at or near level. Use a carpenter’s level to measure from a constant
surface and adjust the support straps as necessary.

NOTE: SV4.5VF (Secure Vent), SF4.5VF (Secure Flex) firestop/spacer must be used any time vent pipe passes
through a combustible floor or ceiling. SV4.5HF (Secure Vent), SF4.5HF (Secure Flex) firestop/spacer must be used
any time vent pipe passes through a combustible wall.

Do not join separate sections of concentric flexible vent together.

Table 21: Rear Vent—No Elbows

See Table 21 as an aid in venting component selection for a
particular range of exterior wall thicknesses.

Note: “H” is horizontal distance from rear of unit to outer wall
surface

NOTE: When venting Rear Horizontal with slip collar and
termination only, install base vent restrictor with the
breakaway portion raised.

Table 22: Top Vent—One 90° Elbow, Elbow Connection at Fireplace

Install the U-shaped vent restrictor in any vent run with
more than 4 ft of vertical rise. See Page 22 for more
information.

See Table 20 as an aid in venting component selection for a
particular range of exterior wall thicknesses.

NOTE: Only in top vent where elbow is connected at fireplace collar
is it allowed to count elbow as 1 ft. vertical (V) rise.

H Maximum V Minimum

feet meters feet meters

3 0.91 Elbow only

WARNING

H = 21” (533 mm) maximum

28”

(711 mm) to outside

of termination

When using Secure Flex®, use

*

wall firestop/spacer SF4.5HF.

H

Wall
firestop/
spacer
SV4.5HF *

**When using Secure Flex, use
Wall Firestop/Spacer SF4.5HF

V

33

Innovative Hearth Products



Wall Firestop/Spacer

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Table 23: Top Vent—One 90° Elbow, Elbow Connection NOT at Fireplace

H Maximum V Minimum

feet meters feet meters

5 1.524 1 0.305

10 3.048 2 0.610

15 4.572 3 0.914

25 7.62 5 1.524

Install the U-shaped vent restrictor in any vent run with more than 4 ft of vertical rise. See
Page 22 for more information.

See Table 20 as an aid in venting component selection for a particular range of exterior wall thicknesses.
If 25 ft of (H) horizontal vent run is needed, then 5 ft minimum of (V) vertical vent will be required.
This table shows a 1 (V) to 5 (H) ratio. For every 1 ft of (V) vertical, you are allowed 5 ft of (H)

horizontal run, up to a maximum horizontal run of 25 ft (7.62 m).

Table 24: Rear Vent—Two 90° Elbows

H + H1 Maximum H Maximum V Minimum

feet meters feet meters feet meters

5 1.524 2 0.610 1 0.305

10 3.048 4 1.219 2 0.610

15 4.572 6 1.829 3 0.914

25 7.62 10 3.048 5 1.524

V + H + H
H = 8 ft (2.438 m) maximum
H + H1 = 25 ft (7.62 m) maximum
Install the U-shaped vent restrictor in any vent run with more than 4 ft of vertical rise. See

Page 22 for more information.

See Table 20 as an aid in venting component selection for a particular range of exterior wall thicknesses.
If 25 ft of (H) horizontal vent run is needed, then 5 ft minimum of (V) vertical vent will be required.
This table shows a 1 (V) to 5 (H) ratio. For every 1 ft of (V) vertical, you are allowed 5 ft of (H)

horizontal run, up to a maximum horizontal run of 25 ft (7.62 m).

= 60 ft (18.288 m) maximum

1

Wall firestop/spacer SV4.5HF **

Wall Firestop/Spacer

(SV4.5HF)

*

When using Secure Flex®, use
ceiling firestop/spacer SF4.5VF.

**

When using Secure Flex, use wall
firestop/spacer SF4.5HF.

H1

H

1

Wall firestop/

Wall Firestop/
Spacer

spacer

SV4.5HF**

SV4.5HF **

V

V

900285-00 05/2015

H

H

Ceiling

Min. One

firestop/

Foot Vent

spacer

Section

Required

SV4.5VF *

Ceiling

Firestop/Spacer

(SV4.5VF)

H

H

Ceiling
firestop/
spacer
SV4.5VF *

Ceiling
Firestop/Spacer
SV4.5VF*

*When using Secure Flex , use

When using Secure Flex®, use

*

Ceiling Firestop/Spacer SF4.5VF.

ceiling firestop/spacer SF4.5VF.

**When using Secure Flex, use

When using Secure Flex, use

**

Wall Firestop/Spacer SF4.5HF.

wall firestop/spacer SF4.5HF.

Installation

V

V

®

Table 25: Top Vent—Two 90° Elbows

H + H1 Maximum V Minimum

feet meters feet meters

3 0.91 Elbow only

5 1.524 1 0.305

10 3.048 2 0.610

15 4.572 3 0.914

25 7.62 5 1.524

V + H + H
H + H1 = 25 ft (7.62 m) maximum

Install the U-shaped vent restrictor in any vent run with more than 4 ft of vertical rise.
See Page 22 for more information.

See Table 20 as an aid in venting component selection for a particular range of exterior wall
thicknesses.

If 25 ft of (H) horizontal vent run is needed, then 5 ft minimum of (V) vertical vent will
be required.

This table shows a 1 (V) to 5 (H) ratio. For every 1 ft of (V) vertical, you are allowed 5 ft of (H)
horizontal run, up to a maximum horizontal run of 25 ft (7.62 m).

34

= 60 ft (18.288 m) maximum

1

H1

H

1

Note - When using

When using Secure



*

Secure Flex

Flex®, use ceiling

Firestop/Spacer SF4.5VF.

firestop/spacer
SF4.5VF.

When using SecureFlex,



When using Secure

use Firestop/Spacer

**

Flex, use wall

SF4.5HF.

TM

, use

firestop/spacer
SF4.5HF.

Wall firestop/spacer

(SV4.5HF)

SV4.5HF **

Wall firestop/spacer

Wall



Firestop/Spacer

(SV4.5HF)

Ceiling



Firestop/Spacer

(SV4.5VF)

H

H

SV4.5HF **

Ceiling

firestop/spacer

Min. One Foot Vent

Section Required

SV4.5VF *

V

V

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Table 26: Rear Vent—Three 90° Elbows

H + H1 + H2 Maximum H Maximum V Minimum

feet meters feet meters feet meters

5 1.524 2 0.610 1 0.305

10 3.048 4 1.219 2 0.610

15 4.572 6 1.829 3 0.914

20 6.096 8 2.438 4 1.219

V + H + H
H = 8 ft (2.438 m) maximum
H + H1 + H2 = 25 ft (7.62 m) maximum

Install the U-shaped vent restrictor in any vent run with more than 4 ft of
vertical rise. See Page 22 for more information.

See Table 20 as an aid in venting component selection for a particular range of
exterior wall thicknesses.

If 20 ft of (H) horizontal vent run is needed, then 4 ft minimum of (V) vertical vent will
be required.

This table shows a 1 (V) to 5 (H) ratio. For every 1 ft of (V) vertical, you are allowed 5
ft of (H) horizontal run, up to a maximum horizontal run of 20 ft (6.096 m).

+ H2 = 60 ft (18.288 m) maximum

1

H2

H

2

*

When using

*When using Secure Flex , use

Secure Flex®, use

Ceiling Firestop/Spacer SF4.5VF.

ceiling firestop/spacer

**When using Secure Flex, use

SF4.5VF.

Wall Firestop/Spacer SF4.5HF.

**

When using Secure

®

Flex, use wall firestop/
spacer SF4.5HF.

Wall firestop/spacer

Wall Firestop/Spacer

SV4.5HF **

SV4.5HF**

H

H1

1

Ceiling

Ceiling

firestop/spacer

Firestop/Spacer

SV4.5VF *

SV4.5VF*

V

V

Installation

900285-00 05/2015

H

H

Table 27: Top Vent—Three 90° Elbows

H Maximum V Minimum

feet meters feet meters

5 1.524 Elbow only

5 1.524 1 0.305

10 3.048 2 0.610

15 4.572 3 0.914

20 6.096 4 1.219

H + H

= 25 ft (7.62 m) maximum

1

V + V1 + H + H1 = 60 ft (18.288 m) maximum

Install the U-shaped vent restrictor in any vent run with more than 4 ft of
vertical rise. See Page 22 for more information.

See Table 20 as an aid in venting component selection for a particular range of
exterior wall thicknesses.

If 20 ft of (H) horizontal vent run is needed, then 4 ft minimum of (V) vertical vent
will be required.

This table shows a 1 (V) to 5 (H) ratio. For every 1 ft of (V) vertical, you are allowed
5 ft of (H) horizontal run, up to a maximum horizontal run of 20 ft (6.096 m).

H1

H

1

Wall firestop/spacer

Wall Firestop/Spacer

SV4.5HF **

SV4.5HF**

V1

*When using Secure Flex, use

When using Secure Flex®, use

*

ceiling firestop/spacer SF4.5VF.

Ceiling Firestop/Spacer SF4.5VF.

When using Secure Flex, use wall

**

**When using Secure Flex, use

firestop/spacer SF4.5HF.

Wall Firestop/Spacer SF4.5HF.

Ceiling

Ceiling
Firestop/Spacer

firestop/spacer

SV4.5VF*

SV4.5VF *

H

H

V

1

Wall firestop/spacer

Wall Firestop/Spacer

SV4.5HF **

SV4.5HF**

V

V

35

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Vertical or Horizontal Venting Using Secure Flex Kits and Components

Secure Flex venting kits and components may be used in any other vent installation where rigid Secure Vent® (SV4.5)
direct-vent components can be used. All restrictions, clearances and allowances pertaining to rigid vent also apply to
flexible vent. Do NOT modify Secure Flex kits . Also, do NOT join separate sections of flex vent together. Secure Flex
kits can be installed on the end of a Secure Vent (SV4.5) rigid vent run, provided that doing so does not violate any
of the venting length, height, routing, horizontal to vertical ratio requirements, or clearance considerations detailed in
this manual. When combined, a rigid vent should not be installed between two flexible vents.

Secure Flex kits come with an included adaptor that can be installed on the fireplace collar or the inclined channel
end of the last Secure Vent (SV4.5) vent section in a rigid system in the exact same fashion as any other Secure Vent
section. Align the dimpled end of the adaptor over the previously installed section or fireplace collar, adjusting the
radial alignment until the four locking dimples of the adaptor are aligned with the inlets of the four incline channels of
the last vent section or collar. Push on the adaptor until it is fully engaged, then twist the adaptor clockwise running
the dimples down and along the incline channels until they seat at the end of the channels.

Figure 28: Flexible Vent Adaptor Figure 29: Flexible Vent

Apply ONLY MIL-PAC BLACK

HIGH TEMPERATURE

SEALANT (P/N 10K81) to

the outside surface of both

collars of the adaptor (fill the

grooves of the outer collar to

be covered by the flexible pipe)

and slide the flexible vent over

the inner and outer adaptor

collars

Installation

900285-00 05/2015

Flexible vent Flexible vent section

Securing screws
in three (3) places
through perforation
and into the pipe

5” (127 mm)
radius minimum

Gear clamps

1 3/4” (44 mm) flexible

vent and adaptor outer

collar overlap

Adaptor (SV4.5RF)

NOTE: Outer vent pipe is pulled away
to show inner vent pipe details.

Attach adaptor to vent collar or Secure Vent sections

1 3/4” (44 mm) flexible
vent and adaptor inner
collar overlap

Securing screws
in three (3) places
through perforation
and into the pipe

Shown here: 36” Flex Connector Kit

36” of flex with two adaptors for mating

two rigid sections of vent together.

(H7748)

1. Install the Inner Flex Pipe.
a. Install the small gear clamp loosely around the inner flexible vent, then push it back out of the way.

b. Apply a bead of Mill-Pac Black (700 °F) high temperature sealant (P/N 10K81) to the inner adaptor collar,

approximately 1/2” from the end.

c. Pull and extend the inner flexible vent.
d. Slide the inner flex vent over the adaptor collar at least 1 3/4”.
NOTE: Ensure the flex vent is free from damage or tears.
e. Slide the gear clamp down and tighten it fully to secure the flexible vent to the adaptor inner collar

approximately 3/4” from the end of the flex.

f. Install three (3) screws 120° apart through the flexible vent and into the adaptor collar just below the gear

clamp to provide additional security to the connection.

2. Install the outer Flex Pipe.
a. Install the large gear clamp loosely around the outer flexible vent pipe, then push it back out of the way.

36

b. Apply a bead of Mill-Pac Black (700 °F) high temperature sealant (P/N 10K81) to the outer adaptor collar.

Cover to the grooves of the collar that extend approximately 1” from the end and to the flat surface,
approximately 1 3/8” from the end.

c. Pull and extend the outer flexible vent.
d. Slide the outer flexible vent over the adaptor collar. Ensure the flexible vent completely engages the adaptor collar

1 3/4” from the end, and that it is free from damage or tears.

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

e. Slide the gear clamp down and tighten it fully to secure the flexible vent to the adaptor outer collar

approximately 3/4” from the end of the flexible vent.

f. Install three (3) screws 120° apart through the flexible vent and into the adaptor collar just below the gear

clamp to provide additional security to the connection.

3. Route the flexible vent.
NOTE: Ensure that the flexible vent is properly routed to provide the required clearance. Do NOT allow the flexible vent

to bend in a radius tighter than 5” (127 mm) (Figure 29). Place the internal flexible vent spacers evenly and avoid
kinking the inner vent. Support horizontal sections of flexible vent with metal straps at 2 ft (0.61 m) intervals.

4. Install firestop/spacers at ceiling and wall penetrations.

• SF4.5 VF firestop/spacer for ceilings

• SF4.5 HF firestop/spacer for walls
NOTE: See the appropriate sections and figures shown throughout the venting section for installation

requirements.

5. Attach the flexible vent to the termination.

®

NOTE: Secure Flex
vent cut to size at the job site. Attach the flexible vent to the Secure Flex terminations as it was attached to the
adaptor (Figure 29).

NOTE: Attach Secure Flex vent to Secure Flex terminations only. Do NOT substitute Secure Vent
or Secure Vent adaptor for Secure Flex components. Secure Flex termination and adaptor collars are a
different circumference than Secure Vent collars. Secure Flex vent has an longer center tube to improve
ease-of-installation.

components can be purchased separately and attached to bulk lengths of Secure Flex flexible

®

terminations

Installation

12. Complete the Field Wiring

The ground supply lead must be connected to the wire attached to the green ground screw
located on the outlet box (see wiring diagrams). Failure to do so will result in a potential
safety hazard. The appliance must be electrically grounded in accordance with local codes
or, in the absence of local codes, the National Electrical Code, ANSI/NFPA 70—latest
edition (in Canada, the current CSA C22-1 Canadian Electrical Code).

Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation.

Au moment de l’entretien des commandes, étiquetez tous les fils avant de les débrancher.
Des erreurs de cáblage peuvent entraîner un fonctionnement inadéquat et dangereux.

Verify proper operation after servicing.

S’assurer que l’appareil fonctionne adéquatement une fois l’entretien terminé.

The gas valve is set in place and pre-wired at the factory for both millivolt and electronic models.

CAUTION

CAUTION

ATTENTION

Millivolt Wiring

Millivolt units are not provided with factory-installed controls; therefore, one of the optional control switches is
required to operate the unit (Page 68):

• ON/OFF Wall Switch,

• Unit-Mountable ON/OFF Switch *,

• Thermostat, or

• Remote Control.

See the Operation section on Page 54 for more details.

1. If installing an ON/OFF wall switch or thermostat, mount it in a convenient location on a wall near the fireplace.

2. Wire the control switch within the millivolt control circuit using the 15 ft of 2-conductor wire supplied with

the unit (Figure 33).

37

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

NOTE: The supplied 15 ft of 2-conductor wire has one end of each conductor connected to the gas valve circuit and
the other end of each conductor placed loose inside the bottom compartment.

CAUTION

In millivolt systems, do NOT connect a wall switch to a 120 V power supply.

Figure 30: Wiring Diagram—Electronic Gas Valves (Traditional Models)

JUNCTION

BOX

120V AC

B
W

G

HOT

NEUTRAL

GROUND

AC/DC
POWER
ADAPTOR

Installation

900285-00 05/2015

B

B

BL

HI/LOW

SWITCH

2B 1B

21

2A

1A

1

2

ON/OFF WALL

SWITCH

BATTERY

R

O

B

R

B

G

HOLDER

B

R

Y
G

O

O

SPLIT
FLOW

O

PROFLAME VALV E

PILOT TUBE

SPARK WIRE CABLE

PILOT GROUND WIRE

BL

BL

G

W

W

B

ELECTRONIC PILOT ASSEMBLY

HOOD

B

Y

IGNITER ROD

Y
G

O

PROFLAME
DFC BOARD

FLAME SENSOR

B

PILOT
SENSOR
CABLE

W

WIRING COLOR CODE

B = BLACK
BR = BROWN
GY = GRAY
PU = PURPLE
R = RED

BL = BLUE
G = GREEN
O = ORANGE
W = WHITE
Y = YELLOW

BATTERY
HOLDER

R

R

B

W

R

BL

W

DFC WIRE HARNESS

BL

B

G

CPI SWITCH
OFF (O) = INTERMITTANT PILOT MODE
ON (–) = STANDING PILOT MODE

38

Electronic Wiring

One of the following optional controls must be used:

• ON/OFF Wall Switch,

• Thermostat, or

• Remote Control.

See the Operation section on Page 54 for more details.

NOTE: Electronic models must be connected to the main power supply.

1. Route a 3-wire, 120 Vac, 60 Hz, 1 ph power supply to the fireplace junction box.

2. Remove the electrical inlet cover plate from the side of the unit by removing the plate’s securing screws

(Table 8).

3. If unit is not supplied with a strain relief, remove the cover plate knockout. Then, feed the power supply wire
through the knockout opening and into the unit junction box.

4. Connect the black power supply wire to the lower outlet’s red pigtail lead (Figure 32 and Figure 33). Connect the
white power supply wire to the outlet’s common terminal.

5. Connect the ground supply wire to the pigtail lead attached to the outlet’s green ground screw. Restrain the inlet
power lead per NEC or local codes.

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

6. If a wall-mounted ON/OFF control, High/Low switch, or thermostat is to be used, mount it in a convenient location on a wall
near the fireplace.

7. If an optional control is to be used, wire it in the low voltage circuit (Figure 31).
NOTE: The supplied 15 ft of 2-conductor wire has one end of each conductor connected to the gas valve circuit

and the other end of each conductor placed loose inside the bottom compartment.

8. After the wiring is complete, replace the cover plate.

WARNING

Electronic models of these appliances are equipped with a three-prong (grounding)
plug utilized in connecting the electronic components to the junction box in the lower
compartment. This grounding plug provides protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle. DO NOT cut or remove the
grounding prong from the plug.

Figure 31: Wiring Diagram—Electronic Gas Valves (Contemporary Models)

Installation

900285-00 05/2015

Pilot Assembly

Valve

Step

Motor

/PTP Outlet

Pilot Outlet

Varable Main Outlet

Gas Valve

Optional

Fixed Outlet

Main Burner

Thermocouple Ground - Connector
to Chassis Ground or Valve Body

Thermocouple - To "S"
Terminal on Main Module

Dry -

Contact

Switches

Battery Pack

Valve Safety
Operator

Thermocouple

Inlet

Regulator

To Pilot

IPI/ Cont Pilot (yellow)

Hi/Lo (blue)

Burner On/Off (brown)

From Pilot

Igniter

Inlet

PTP Inlet

Igniter - From "I" Termi-

Battery

Switches

VCS - ECOMODBLD

(Main Module)

nal on Main Module

7.5VDC
1-Amp

Adaptor

Power

(Not Polarity
Sensitive)

Motor

13. Install the [Optional] Blower Kit after Installation in the Framing

NOTE: For steps 11 and 12, it may be helpful to remove the control compartment door (Page 56).

FBK-100, FBK-200, and FBK-250 Kits

An electrical outlet box is provided for the installation of the FBK-100, FBK-200, and FBK-300 forced air blower kits.
Electrical power must be provided to the box to operate the blower. Install the blower kit according to the installation
instructions provided with the kit.

NOTE: The tab connecting the receptacles of the outlet box must be broken in FBK-100 and FBK-200 blower kit
applications (Figure 34).

39

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Figure 32: Junction Box Wiring, 120 V, 60 hz, 1 phase Figure 33: Wiring Diagram—

Millivolt Gas Valves

Wall-mounted ON/

Ground: green

Neutral: white

120 VAC: black

Junction

box

Black

White

*

OFF blower switch
or variable speed
control switch

Tab
broken

Hot side of

Red

receptacle

APPLIANCE- MOUNTED
ON/OFF SWITCH
(OPTIONAL)

BK/W(1)

BK/W(1)

WALL-MOUNTED ON/OFF SWITCH (OPTIONAL)
THERMOSTAT (OPTIONAL)

WALL MOUNTED CONFIGURATION FOR FAN SWITCH (OPTIONAL)

THERMOPILE

TP-TH

TP
TH

GAS VALVE

Installation

900285-00 05/2015

Green

Plug blower into

this receptacle

Ground

Blower

Tab
intact

Field wired

Factory wired

Neutral side
of receptacle

Green ground screw

FAN

(OPTIONAL)

JUNCTION BOX

BLACK

BK

R

W

AC

GR

120 V

14. Connect the Gas Line

All codes require a shutoff valve mounted in the supply line. Figure 35 illustrates two methods for connecting the
gas supply. The flex-line method is acceptable in the U.S., however, Canadian requirements vary depending on
locality. Installation must be in compliance with local codes.

NOTE: Ensure the CPI/IPI switch is set to intermittent mode with the pilot in the OFF position. See control
compartment door label for more information.

NOTE: A sediment trap is recommended in the gas piping within the home to prevent moisture and debris in the line
from damaging the valve.

NOTE: Secure all joints tightly using appropriate tools and sealing compounds (ensure propane resistant compounds
are used in propane applications). Seal around the gas line to prevent cold air leakage. Gas line holes and other
openings can be caulked or stuffed with unfaced fiberglass insulation.

Figure 34: Control Compartment Figure 35: Gas Line Connection

Gas

valve

3/8 NPT x 3/8”
Flare fitting

1/2 x 3/8” Flare
shutoff valve

40

Main gas

shutoff valve

Gas valve

Optional burner ON/OFF switch (millivolt units)

CPI/IPI switch (electronic units)

These fireplaces are equipped with a gas flex line for use (where permitted) in connecting the unit to the gas line. A
gas flex line is provided to aid in attaching the direct-vent fireplace to the gas supply. The gas flex line can only be
used where local codes permit. The flex line is rated for both natural and propane gas. A manual shut off valve is also
provided with the flex line.

The gas control valve is located in the lower control compartment (Figure 34).

Access the Control Compartment

See Page 56 for instructions on Accessing the Control Compartment.
Millivolt and electronic control valves have a 3/8” (10 mm) NPT thread inlet port.

Piezo
(millivolt units)

Door latch

3/8” Nipple

3/8” Union

3/8” Flex tubing

3/8” Close nipple

3/8” Shutoff valve

(Optional) flexible gas

line connector

1/2 x 3/8”

Reducer

Gas
stub

Innovative Hearth Products

Ignitor

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Secure all joints tightly using appropriate tools and sealing compounds (ensure propane resistant compounds are
used in propane applications). Optionally, seal around the gas line to prevent cold air leakage. Gas line holes and
other openings can be caulked or stuffed with unfaced fiberglass insulation.

All codes require a shutoff valve mounted in the supply line. The orientation of the shutoff valve should face the
front. Figure 35 illustrates two methods for connecting the gas supply. A sediment trap is recommended to prevent
moisture and debris in the gas line from damaging the valve.

Test Factory and Field Connections for Gas Leaks

Never use an open flame to check for leaks.

Turn on gas supply and test for gas leaks, using a gas leak test solution—also known as bubble leak solution.
NOTE: Using a soapy water solution is an effective leak test solution but it is not recommended, because the soap

residue that is left on the pipes/fittings can result in corrosion over time.

1. Light the fireplace (refer to the lighting instructions label in the control compartment or Page 70).

2. Brush all joints and connections with the gas leak test solution to check for leaks. If bubbles are formed, or

gas odor is detected, turn the gas control knob (OFF/PILOT/ON) to the OFF position (millivolt units), or turn the
receiver or remote control to the OFF position (electronic units). Either tighten or refasten the leaking connection,
and then retest as described above.

3. When the gas lines are tested and leak free, rinse off the leak testing solution

Installation

900285-00 05/2015

WARNING

15. Verify Proper Fireplace Operation

1. With the gas line installed, inspect the system before closing the front of the unit.

2. Follow the pilot lighting instructions:

• Millvolt Systems (Page 70)

• Electronic Systems (Page 72 traditional, Page 74 contemporary)
NOTE: When lighting the fireplace for the first time, it will take a few minutes for the gas line to purge itself of air.

When purged, the pilot and burner will light and operate as indicated. Subsequent lighting of the fireplace will not
require purging. Inspect the pilot flame (carefully remove logs, if necessary).

Millivolt Fireplace Inspection

The pilot flame should be steady, not lifting or floating. Flame should be blue in color with traces of orange at the
outer edge. The top 3/8” (10 mm) at the pilot generator (thermopile) and the top 1/8” (3.175 mm) minimum (tip) of
the quick drop out thermocouple should be engulfed in the pilot flame. The flame should project 1” (25 mm) beyond
the hood at all three ports (Figure 36). Replace the logs if removed for pilot inspection.

To light the burner, turn ON the remote wall switch and rotate the gas valve control knob counterclockwise to the ON
position (the top of the valve).

Electronic Fireplace Inspection

To light the burner, turn ON the wall or remote control switch. Ensure the igniter lights the pilot. The pilot flame
should engulf the flame rod (Figure 37).

Figure 36: Millivolt Pilot Figure 37: Electronic Pilots

Hood

Igniter rod

Thermocouple

Igniter

Pilot Hood

Igniter

Pilot
Hood

Pilot Hood

Pilot

nozzels

Thermopile

3/8”

(9 mm)

min

Flame Rod

Traditional Contemporary

Sensor

Thermocouple

41

Innovative Hearth Products

TM

Superior

16.

17. Install the Logs, Volcanic Stone, and Glowing Embers or Glass Media in Contemporary Fireplaces

18. Install the Glass Door

19. Adjust the Air Shutter to Ensure Proper Flame Appearance

DRT/C3000 Series Direct-Vent Gas Fireplaces

Optional: Install the Firebox Liners

1. See Page 57 for instructions on Traditional Only: Installing the Firebox Liners.

1. See Page 57 for instructions on Installing the logs, volcanic stone, and glowing embers or glass media in

contemporary fireplaces.

1. See Page 61 for instructions on Installing and removing the glass door.

WARNING

• Air shutter adjustment should only be performed by a qualified professional service technician.

• Ensure glass door is in place and sealed during adjustment.

Installation

900285-00 05/2015

• Soot will be produced if the air shutter is closed too much. Any damage due to sooting,
resulting from improperly setting the air shutter, is not covered under the warranty.

• The air shutter rod and nearby appliance surfaces are hot. Exercise caution to avoid injury
while adjusting flame appearance.

Flame Appearance and Sooting

The flame should be blue at the base, and yellow-orange in the body of the flame.
When the fireplace is first lit, the entire flame may be blue and will gradually turn yellow-orange during the first 15

minutes of operation. If the flame remains blue, or if the flame is orange with evidence of sooting (black tip), the air
shutter opening may need to be adjusted.

If the air shutter opening is closed too far, sooting may develop. Sooting is indicated by black puffs developing at the
tips of very long orange flames. Sooting results in black deposits forming on the logs, fireplace inside surfaces, and
on exterior surfaces adjacent to the vent termination.

Sooting is caused by incomplete combustion in the flames and lack of combustion air entering the air shutter
opening. To achieve a warm yellow-orange flame with an orange body that does not soot, the shutter opening must
be adjusted between these two extremes.

Air Shutter Adjustment Guidelines

• If smoke or soot is present, first check the log set positioning to ensure that the flames are not impinging on any
of the logs. If the log set is properly positioned and a sooting condition persists, then the air shutter should be
opened more.

• The more offsets in the vent system, the wider the air shutter will need to be opened.

• An fireplace operated with the air shutter opened too far may have flames that appear blue and transparent.
These weak, blue, and transparent flames are termed anemic.

• Propane models may exhibit flames that candle or appear stringy. If this condition is present and persists, adjust
the air shutter to a more closed position, then operate the fireplace for a few more minutes to ensure that the
flame normalizes and the flames do not appear sooty.The following chart is provided to help achieve the correct
air shutter adjustment for your installation.

CAUTION

42

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

Table 28: Air Shutter Adjustment Guidelines Figure 38: Air Shutter Adjustment Rod

Amount of Primary

Air

If air shutter is

closed too far

If air shutter is

open too far

Flame Color Air Shutter Adjustment

Flame will

be orange

Flame will

be blue

Air shutter gap should be increased

Air shutter gap should be decreased

Burner

Tube

Air Shutter

Adjustment

Rod Down

(Fully-Open

Position)

Adjustment
Set-Screw

Adjustment
Rod Up
(Fully-Closed
Position)

1. Move the adjustment rod down to increase air flow and up to decrease it. The rod is located in the lower control
compartment. Position the air shutter to the factory setting (Table 29).

2. Light the fireplace. Follow the lighting procedure on the lighting label in the control compartment or Page 70.

3. Allow the burner to operate for at least fifteen (15) minutes while observing the flame continuously to ensure

that the proper flame appearance is achieved (Figure 39 and Figure 40). If the following conditions are present,
adjust accordingly.

• If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper

flame appearance is achieved.

• If flame remains blue, adjust the air shutter, incrementally, to a more closed position until the proper flame

appearance is achieved.

4. When satisfied that the burner flame appearance is normal, reinstall the lower control compartment door, then
proceed to finish the installation.

Figure 39: Fireplaces Flame Appearance

Table 29: Main Burner Shutter Opening—Factory Setting

Models Natural Gas Propane

All

1/16”

(1.6 mm)

Space Reserved

for

Contemporary Image

1/8”

(3.2 mm)

20. Install the Hood (in Traditional Models)

NOTE: Traditional models must have a hood installed prior to operation.

1. Install the hood by sliding it into the slots on the lower edge of the cabinet top.

NOTE: To install the non-combustible finish material flush with the top of the hood, the hood must be installed

before installing the finish material. If finish material is installed flush with the top edge of the hood, the hood cannot
be removed.

43

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

NOTE: To install the hood after installing the non-combustible finish material over the black surface above the
fireplace opening, the bottom edge of the finish material must be 5/8” above the top edge of the hood to allow
clearance for installation and removal of the hood.

Reinstall the Included Barrier

21.

Reinstall any barrier removed before operating the fireplace. The barrier is designed
to reduce the risk of burns from hot glass. Do not operate the fireplace without the
barrier installed.

NOTE: All models must have a barrier installed prior to operation.

1. Open the control compartment door (Page 56).

2. Hold the barrier in front of the glass door and slide it up into the slots above the glass door and under the hood.

3. Slide the barrier bottom down into the slots below the glass door, securing it in place.

22. Install the Finishing Materials

1. Complete finished interior wall.

NOTE: To install the fireplace facing flush with the finished wall, position framework to accommodate the thickness

of the finished wall.

Installation

900285-00 05/2015

WARNING

NOTE: In contemporary models only, finish wall flush to face of unit and install facade base and panel. Frame

assembly to complete the front of the fireplace (see facade installation instuctions, Page 46).

Figure 40: Combustible Wall Framing Figure 41: Face Mounting Elements

This Area
Must Remain
Clear of
Combustible
Materials

Combustible

Finished Wall

Materials

Stand Off

Must Be Bent

To Vertical

Position

Standoff

Provides

Space From

Combustible

Materials

Hood

4” Clearance
Minimum

1” Min.
(25 mm)

Top Of
Appliance

NOTE: See Cold Climate Insulation on Page 10 and Vent Termination Clearances on Page 12.

23. Attach the Safety-in-Operation Warning Labels

Top Face Brackets

3”

(76 mm)

Fireplace face foot slots

1. Attach the furnished safety instruction labels at all fireplace operation and control points (Page 47).

NOTE: The installer MUST ensure these warnings are properly attached during installation. The warning labels are a

critical means of informing consumers of safe operation practices.

24. Installing Batteries for Backup and Wall Switch

1. Locate the battery backup and place four (4) AA batteries in the backup battery holder (Page 38).

2. Locate the wall switch and secure four (4) AA batteries in the wall switch battery holder (Page 38).

NOTE: Replace batteries as a part of standard maintenance (Page 65) and as needed when troubleshooting (Page

44

76).

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

Installing Facade

Step 1. Slide top trim pieces over flange of panel until seated squarely. Step 2. Slide side trim pieces into place (top will overlap slightly). Repeat

Step 1 and Step 2 for bottom and opposite side trim for panel.

NOTE: Remove protective flim from all stainless components
before installation.

Step 3. Plug lead wires into the IPI/CPI Switch on right side of
facade base.

45

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

Step 4a. Slide the foot tabs of the facade base into the slots (see Figure

41) on both sides near the bottom of the fireplace opening.

Step 5. Slide the tabs on the back of both sides of the facade panel into
the slots on the base.

Step 4b. Tilting the facade base up on its foot tabs, secure the top by
engaging the three brackets (see Figure 41) on the face of the fireplace
with the three cut outs on the back top of the facade base.

(Black Base and Stainless Panel shown)

46

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation

900285-00 05/2015

ATTACH THE SAFETY-IN-OPERATION WARNINGS

NOTE: It is the installer’s responsibility to ensure these warnings are properly affixed during installation. These warning labels are a

critical step in informing consumers of safe operation of this fireplace.

Attaching Safety-in-Operation Warnings

It is required that the safety instruction labels
furnished with the fireplace be affixed to the
operation and control point of the fireplace. A
safety instruction label must be affixed to the wall
switch plate where the fireplace is turned on and
off (Figure A) or wall thermostat (Figure B) and if
used on the remote control handheld transmitter
(Figure C). The warnings should already have
been put in place when the fireplace initial set-up
was completed. If they are not affixed at these
spots, locate the multi-lingual adhesive labels
provided with these instructions and proceed as
follows:

1. Locate the wall switch or wall thermostat

that controls the fireplace (verify the switch
operates the fireplace by turning it on and
off). Clean the wall switch plate or wall
thermostat thoroughly to remove any dust
and oils. Affix the label to the surface of the
plate of the wall switch that controls the
fireplace (Figure A) or the wall thermostat
(Figure B). Choose the language primarily
spoken in the home. If unknown, affix the
English language label.

2. If a remote control is used to control the

fireplace, locate the transmitter and clean
it thoroughly to remove any dust and oils.
Affix the label to the surface of handheld
transmitter (Figure C). Choose the language
primarily spoken in the home. If unknown,
affix the English language label.

3. If you are unable to locate the labels, please

contact IHP or your nearest IHP dealer to
receive additional safety instruction labels
free of charge.

Cat. No. H8024 Replacement Label Kit Étiquettes de remplacement, n° cat. H8024 Juego de etiquetas de repuesto - Nº de cat. H8024
NOTE: English is red text on clear label. French

and Spanish are white text on black label.

SAFETY LABEL DIAGRAMS DIAGRAMMES DES ÉTIQUETTES DE SÉCURITÉ DIAGRAMAS DE ETIQUETAS DE SEGURIDAD

Apposition des mises en garde relatives
à la sécurité d’utilisation

Il est impératif que les étiquettes de sécurité
fournies avec le foyer soient collées à côté
des dispositifs de contrôle du foyer. Une
étiquette de sécurité doit être collée sur la
plaque de l’interrupteur contrôlant l’allumage
du foyer (Figure A) ou sur le thermostat mural
(Figure B) et, le cas échéant, sur le boîtier de
la télécommande (Figure C). Les mises en
garde auraient dû être collées au moment de
l’installation initiale du foyer. Si ce n’est pas le
cas, prenez les étiquettes adhésives multilingues
fournies avec ces instructions et procédez
comme suit:

1. Repérez l’interrupteur ou le thermostat mural

qui contrôle le foyer (vérifiez que l’interrupteur
contrôle le fonctionnement du foyer en le
faisant basculer de Marche à Arrêt, et vice­versa). Nettoyez soigneusement la plaque
murale de l’interrupteur ou le thermostat
mural pour éliminer la poussière et les traces
de graisse ou d’huile. Collez l’étiquette sur la
surface de la plaque de l’interrupteur mural qui
contrôle le foyer (Figure A) ou du thermostat
mural (Figure B) . Choisissez la langue qui
est principalement parlée dans la résidence
du propriétaire. En cas de doute, collez
l’étiquette en anglais.

2. Si une télécommande est utilisée pour

contrôler le foyer, nettoyez la soigneusement
pour éliminer la poussière et les traces de
graisse ou d’huile. Collez l’étiquette sur
le boîtier de la télécommande (Figure C).
Choisissez la langue qui est principalement
parlée dans la résidence du propriétaire. En
cas de doute, collez l’étiquette en anglais.

3. Si vous ne parvenez pas à localiser les

étiquettes, s’il vous plaît contactez IHP ou
votre revendeur le plus proche pour recevoir
IHP étiquettes d’instructions de sécurité
supplémentaires gratuitement.

Remarqué : Le texte anglais est rouge sur un
support transparent. Le texte français et espagnol
est blanc sur un support noir.

Colocación de advertencias de
seguridad en operación

Se requiere que las etiquetas de instrucciones de
seguridad incluidas con la chimenea se coloquen
en el punto de operación y control de la misma.
Se debe colocar una etiqueta de instrucciones
de seguridad en la placa del interruptor de pared
desde el cual se enciende y se apaga la chimenea
(Figura A) o en el termostato de pared (Figura B) y
en el transmisor de control remoto (Figura C) si se
usa. Las advertencias ya deben haberse colocado
cuando se completó la instalación inicial de la
chimenea. Si no están colocadas en estos lugares,
encuentre las etiquetas adhesivas multilingües
proporcionadas con estas instrucciones y prosiga
de la siguiente manera:

1. Identifique el interruptor o el termostato de

pared que controla la chimenea (verifique
que el interruptor opera la chimenea
encendiéndola y apagándola). Limpie bien
la placa del interruptor o el termostato de
pared para quitar el polvo y aceite. Pegue
la etiqueta en la superficie de la placa
del interruptor que controla la chimenea
(Figura A) o en el termostato de pared
(Figura B). Seleccione el idioma que más se
habla en la casa. Si no sabe cuál es, use la
etiqueta en inglés.

2. Si se usa un control remoto para controlar

la chimenea, encuentre el transmisor y
límpielo bien para quitar el polvo y aceite.
Pegue la etiqueta en la superficie del
transmisor (Figura C). Seleccione el idioma
que más se habla en la casa. Si no sabe cuál
es, use la etiqueta en inglés.

3. Si usted es incapaz de localizar las etiquetas,

por favor póngase en contacto con IHP,
o con su distribuidor más cercano IHP
recibir instrucción etiquetas de seguridad
adicionales sin costo.

Nota: La etiqueta en inglés es transparente con
texto rojo. Las etiquetas en francés y español son
negras con texto blanco.

Illustrations are for example only.
Your accessories may be different.

Les illustrations sont par exemple
uniquement. Vos accessoires
peuvent être différents.

Las ilustraciones son sólo ejemplos.
Tu accesorios pueden ser diferentes.

Figure A
Figura A

Innovative Hearth Products

PRG

On

Remote

Off

Figure B
Figura B

Figure C
Figura C

47

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

INSTALLATION ACCESSORIES

Table 30: Listed Secure Vent® Components

Installation

900285-00 05/2015

H1968 SV4.5HT-2

94L10 SV4.5HTSS

H5817 SV4.5-20SSWSK

H2152 SV4.5CGV-1

H8914 SV4.5TK90HT2

Horizontal Square Termination
with Firestop/Spacer (H2246),

and Adaptor (74L61)

Rigid, Horizontal, Small Square

Termination with Firestop/Spacer

(H2246), Adaptor (74L61)

(see 750204M)

Rigid, Small, Square Termination,

20” with Shield and Firestop

(see 750247M
and 750204M)

Vertical Termination Cap, High

Wind

Horizontal Termination Kit HT-2

with 90° elbow

77L78 SV4.5F Flat Roof Flashing
77L79 SV4.5FA 1/12 to 7/12 Adjustable Flashing

77L80 SV4.5FB

77L81 SV4.5SC6 Storm Collar (6 pack)

H6183 SV4.5HF5 Firestop Spacer, 5”, rigid

H6184 SF4.5HF5 Firestop Spacer, 5”, flex

H2246 SV4.5HF-10

H2247 SV4.5VF-10

7/12 to 12/12 Adjustable

Flashing

Firestop/Spacer-Horizontal, rigid

(3-1-1 spacing), 10 Pack

Firestop/Spacer-Vertical, rigid

(1-1-1 spacing), 10 Pack

H8915 SV4.5TK90SS

Vent Sections (Rigid)
77L70 SV4.5L6 6” (152 mm)
77L71 SV4.5L12 12” (305 mm)

77L72 SV4.5L24 24” (610 mm) 17M53 SV4.5HGS-12

77L73 SV4.5L36 36” (914 mm)
77L74 SV4.5L48 48” (1219 mm)

77L75 SV4.5LA

77L76 SV4.5E45 45° Elbow

77L77 SV4.5E90 90° Elbow

H5816

750,247M

SV4.5-

TWSK10

Horizontal Termination Kit Small

Square with 90° elbow

Telescopic Length Slip Section

(2–7 1/2” rigid)

Through Wall Shield Kit (to shield

direct-vent pipe from blown

insulation)(see 750247M)

96K92 SV4.5SP Support Plate

17M52 SV4.5HGS-1

87L02 SV4.5HGS

H5820 SV4.5HTSK

H3907 SV4.5ARSA

Termination Guard, Square (1

pack) (see 750109M)

Termination Guard,

Horizontal Square (12 pack)

(see 750109M)

Termination Guard for Horizontal

Square Termination (Deluxe)

(1 pack) (see 750055M)

Termination Shroud (Guard) for

Horizontal Square Termination (1

pack) (see 750246M)

Attic Insulation Shield with

adjustable height, 12–22”

48

Innovative Hearth Products

S

e

a

l

a

n
t

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Table 30: Listed Secure Vent® Components

Installation

900285-00 05/2015

96K93 SV4.5SU Support Strap

99L02 SV4.5HRK14

99L03 SV4.5HRK36

Horizontal Riser Kit, 14”(see

750146M)

Horizontal Riser Kit, 36”

(see 750146M)

Table 31: Listed Secure Flex® Components

Catalog

Number

These termination kits include firestop/spacer, gear clamps, and flex adaptor.

60L10 SF-18

98K03 SF-12

H2248 SF4.5HF-10

H2249 SF4.5VF-10

Model Description

18 ft (5.49 m)* compressed flex (see

750053M)

12 ft (3.66 m)*compressed flex (see

750052M)

Firestop/Spacer, Horizontal, flex (3-1-1

spacing), 10 Pack

Firestop/Spacer, Vertical, flex (1-1-1

spacing),10 Pack

10K81 SFMP

89L40 SFMP-12

Catalog
Number

94L04 SFKIT12SS

94L05 SFKIT18SS

94L06 SFKIT24SS

94L07 SFKIT36SS

Model Description

Mill-Pac, Black, High-

Temperature Sealant

Mill-Pac, Black, High-

Temperature Sealant

(bulk 12-pack)

Small Square Termination for flex, with

12” (305 mm) of *compressed flex vent

(see 750204M)

Small Square Termination for flex, with

18” (457 mm) of *compressed flex vent

(see 750204M)

Small Square Termination for flex, with

24” (610 mm) of *compressed flex vent

(see 750204M)

Small Square Termination for flex, with

36” (914 mm) of *compressed flex vent

(see 750204M)

H1969 SF4.5HT-2

77L87 SFKIT12S

77L88 SFKIT18S

77L89 SFKIT24S

77L90 SFKIT36S

77L91 SFKIT48S

91L66 SFGC4-6 Gear Clamp 4.5” (114 mm) for flex (6-pack)

91L67 SFGC7-6 Gear Clamp 7.5” (190.5 mm) for flex (6 pack)

Horizontal Square Termination for flex

(without flex)

Square Term. for flex with

12” (305 mm)* compressed flex

Square Term. for flex with

18” (457 mm)* compressed flex

Square Term. for flex with

24” (610 mm)* compressed flex

Square Term. for flex with

36” (914 mm)* compressed flex

Square Term. for flex with

48” (1219 mm)* compressed flex

Vertical Termination for flex (flat to 6/12) with

56L74 SFVT30

56L75 SFVT45

H7748 H7748

flex adaptor, section of rigid vent, roof support

collar assembly, roof flashing and storm collar.

(see 750052M)

Vertical Termination for flex (6/12 to 12/12)

with flex adaptor, section of rigid vent, roof
support collar assembly, roof flashing and

storm collar. (see 750052M)

36” Flex Connector Kit.

36” of flex with two adaptors for

mating two rigid sections of vent

together.

*All compressed flex vents can be expanded up to two
times the size of the compressed length.

49

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

GAS CONVERSION KITS

WARNING

This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s
instructions and all applicable codes and requirements of the authority having jurisdiction. If the
information in these instructions is not followed exactly, a fire, explosion, or the production of carbon
monoxide may result; causing property damage, personal injury, or loss of life. The qualified service agency
is responsible for the proper installation of this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified in the manufacturer’s instructions supplied with
the kit.The qualified service agency performing this installation assumes responsibility for this conversion.

AVERTISSEMENT

Cette trousse de conversion doit être installée par un technicien agréé, selon les instructions du fabricant
et selon toutes les exigences et tous les codes pertinents de l’autorité compétente. Assurez-vous de bien
suivre les instructions dans cette notice pour réduire au minimum le risque d’incendie, d’explosion ou la
production de monoxyde de carbone pouvant causer des dommages matériels, des blessures ou la mort.
Le tecnicien agréé est responsable de l’installation de cette trousse. L’installation n’est pas adéquate ni
complète tant que le bon fonctionnement de l’appareil converti n’a pas été vérifié selon les instructions du
fabricant fournies avec la trousse. Le fournisseur de service qualifié ayant réalisé l’installation assume les
responsabilités liées à la conversion.

In Canada:
The conversion shall be carried out in accordance with the requirements of the provincial authorities having

jurisdiction and in accordance with the requirements of the CAN/CGA-B149.1 Installation code.

La conversion devra être effectuée conformément aux recommandations des autorités provinciales ayant
juridiction et conformément aux exigences du code d’installation CAN/CGA-B149.1.

Gas conversion kits are available to adapt your fireplace from the use of one type of gas to the use of another. These
kits contain all the necessary components needed to complete the task including labeling that must be affixed to
ensure safe operation.

Refer to the instructions provided with the conversion kit when performing any gas conversion.

Table 32: Millivolt Systems,Natural Gas To Propane Gas Conversion Kits Table 33: Millivolt Systems, Propane Gas to Natural Gas Conversion Kits

Models Catalog Number Models Catalog Number

33” Models F2168 33” Models F2166
35” Models F2173 35” Models F2171
40” Models F2174 40” Models F2172
45” Models F2180 45” Models F2178

Table 34: Electronic Systems, Natural Gas To Propane Gas Conversion Kits Table 35: Electronic Systems, Propane Gas To Natural Gas Conversion Kits

Models Catalog Number Models Catalog Number

33” Models F2167 33” Models F2165
35” Models F2175 35” Models F2169
40” Models F2176 40” Models F2170
45” Models F2179 45” Models F2177

Table 36: Electronic Systems, Natural Gas To Propane Gas Conversion Kits
(Contemporary Fireplaces)

Models Catalog Number Models Catalog Number

35” Models F2492 35” Models F2494

40” Models F2491 40” Models F2493

50

Table 37: Electronic Systems, Propane Gas To Natural Gas Conversion Kits
(Contemporary Fireplaces)

Innovative Hearth Products

Pressure
Regulator

Remove
These
Components

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installing Gas Conversion Kits

The gas supply shall be shut OFF prior to disconnecting the electrical power, before
proceeding with the conversion.

Avant d’effecteur la conversion, coupez d’abord l’alimentation en gaz, ensuite, coupez
l’alimentation electrique.

1. TURN OFF THE GAS SUPPLY TO THE FIREPLACE and disconnect power supply at the circuit breaker. Ensure

fireplace is cold.

2. Open the lower control compartment door (Page 56).

3. Remove the front glass door/frame from the fireplace (Page 61).

4. Remove the logs. If necessary, remove the log grate.
NOTE: Exercise care so as not to break the logs (Page 64).

5. Remove the sub floor.

6. Remove the two (2) screws securing the burner assembly. Remove the burner assembly with the attached

venturi tube.

Operation

900285-00 05/2015

WARNING

AVERTISSEMENT

Millivolt and Electronic Ignition System Fireplaces

7. Refer to the instructions provided with the SIT Regulator Conversion Kit, and Figure 42. Using a Torx T20
driver (with 1/4” shank) or slotted screwdriver, remove and discard the pressure regulator mounting screws
(two screws for electronic models, three screws for millivolt models), pressure regulator tower, the diaphragm
assembly (if applicable) and the spring. Discard all removed components.

Figure 42: Valve Regulator Conversion

(millivolt shown)

Pressure

Regulator

Remove
these
components

8. Install the new pressure regulator assembly using the supplied screws. Tighten the screws to 25 in. lbs.

9. Install the enclosed identification label to the valve body where it can be easily seen.

10. Remove the pilot hood assembly to access the hex pilot orifice (Figure 43). Remove and replace the pilot

orifice with the one provided with the kit. Exercise extreme care to prevent damage to or breakage of the
igniter assembly.

11. Remove the burner orifice from the manifold and replace it with the one provided in the kit (Figure 44).

Electronic Gas Valve (Contemporary Models)
See Page 53

NOTE: See Table 5 for burner orifice sizes.

51

Innovative Hearth Products

Pilot

Orifice

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Operation

900285-00 05/2015

Figure 43: Millivolt Pilot Figure 44: Orifice

Pilot

Orifice

12. Use pipe joint compound or Teflon® tape on all pipe fittings before installing.
NOTE: Ensure propane resistant compounds are used in propane applications, do not use pipe joint compounds

on flare fittings.

13. Retrieve the burner and hold the venturi tube above the orifice. Place the shutter adjusting rod in the slot of the
shutter arm (Figure 38). Set the burner assembly into its position and secure the trapezoidal plate with the two
screws previously removed.

14. Reinstall the baffle with the two baffle securing screws.

15. Reassemble the remaining components.

16. Turn on gas supply and test for gas leaks (Page 41).

17. Relight the main burner. The lighting instructions can be found on the lighting label in the control compartment
or Page 70. Verify proper burner ignition and operation (Page 42).

18. Inspect the pilot system for proper flame. The pilot flame should engulf the flame sensor (Figure 36 and

Figure 37).

19. Using a manometer, test the inlet and manifold gas pressures (Table 3 and Table 4).

52

NOTE: Always test pressures with the valve regulator control at the highest setting.

Innovative Hearth Products
Superior

TM

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Conversion Instructions Contemporary Models

To convert contemporary fireplaces for another gas, the following components are effected - main orifice, low­rate orifice, regulator setting and pilot setting.

Operation

Step 1. Remove Burner assembly and replace the main
orifice supplied in Kit.

Step 2. Remove the low rate orifice fom the Valve and
replace with the orifice supplied in kit.

Step 3. Remove the regulator set plug. Step 3a. Change the Stem Position on Plug.

Step 3b. Stem Plug - propane positioning or... Step 3c. Stem Plug - natural gas positioning

Step 4. Pull the pilot cap straight up to remove and

expose the pilot orifice.

Step 5. For propane- Turn pilot orifice clockwise until
it stops (do not tighten). For natural gas, turn counter­clockwise until it stops (do not tighten).

Step 6. Reinstall pilot cap. Step 7. Install the the supplied label at rating plate

stating this unit has been converted.

53

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

OPERATION

WARNING

Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to a fireplace or stove, install
an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces.

AVERTISSEMENT

Les jeunes enfants devraient être surveillés étroitement lorsqu’ils se trouvent dans la même pièce que
l’appareil. Les tout petits, les jeunes enfants ou les adultes peuvent subir des brûlures s’ils viennent en
contact avec la surface chaude. Il est recommandé d’installer une barrière physique si des personnes
à risques habitent la maison. Pour empêcher l’accès à un foyer ou à un poêle, installez une barrière de
sécurité; cette mesure empêchera les tout petits, les jeunes enfants et toute autre personne à risque
d’avoir accès à la pièce et aux surfaces chaudes.

WARNING

Reinstall any barrier removed before operating the fireplace. The barrier is designed to reduce the risk of
burns from hot glass. Do not operate the fireplace without the barrier installed.

WARNING

Do not operate the fireplace if:

• The glass front is removed, cracked, or broken

• The surround trim assembly and screen are not installed

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning are similar to the flu with
headaches, dizziness and/or nausea. If you have these signs, obtain fresh air immediately. Turn off the gas
supply to the appliance and have it serviced by a qualified professional, as it may not be operating correctly.
Some people are more affected by carbon monoxide than others, including pregnant women, people with heart
or lung disease or anemia, those under the influence of alcohol, and those at high altitudes.

NOTE: Do not place furniture or other combustible materials within 36” of the front of viewing area(s).
NOTE: Children and adults should be alerted to the hazards of high surface temperature and should stay away to

avoid burns or clothing ignition.

Remarqué : Les enfants et les adultes devraient être infor-més des dangers que posent les températures de
surface élevées et se tenir à distance afin d’éviter des brûlures ou que leurs vêtements ne s’enflamment.

NOTE: Installation and repair should be done by a qualified service person. The fireplace should be inspected before
use and at least annually by a professional service person. More frequent cleaning may be required due to excessive
lint from carpeting, bedding material, etcetera. It is imperative that control compartments, burners and circulating air
passageways of the fireplace be kept clean.

54

Remarqué : L’installation et la réparation devrait être confiées à un technicien qualifié. L’appareil devrait faire

l’objet d’une inspection par un technicien professionnel avant d’être utilisé et au moins une fois l’an par la suite.
Des nettoyages plus fréquents peuvent être nécessaires si les tapis, la literie, et cetera produisent une quantité
importante de pous-sière. Il est essentiel que les compartiments abritant les commandes, les brûleurs et les
conduits de circulation d’air de l’appareil soient tenus propres.

NOTE: Do not use these fireplaces if any part has been under water. Immediately call a qualified, professional service
technician to inspect the fireplace and to replace any parts of the control system and any gas control which have
been under water.

Remarqué : Ne pas utiliser cet appareil s’il a été plongé, même partiellement, dans l’eau. Appeler un technicien qualifié pour
inspecter l’appareil et remplacer toute partie du système de commande et toute commande qui a été plongée dans l’eau.

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

ATTACH THE SAFETY-IN-OPERATION WARNINGS

NOTE: It is the installer’s responsibility to ensure these warnings are properly affixed during installation. These warning labels are a

critical step in informing consumers of safe operation of this fireplace.

Attaching Safety-in-Operation Warnings

Your fireplace has been furnished with safety
instruction labels that are to be affixed to the
operation and control point of the fireplace. A
safety instruction label should be affixed to the
wall switch plate where the fireplace is turned on
and off (Figure A) or wall thermostat (Figure B)
and if used on the remote control handheld
transmitter (Figure C). The warnings should
already have been put in place when the fireplace
initial set-up was completed. If they are not
affixed at these spots, locate the multi-lingual
adhesive labels provided with these instructions
and proceed as follows:

1. Locate the wall switch or wall thermostat

that controls the fireplace (verify the switch
operates the fireplace by turning it on and
off). Clean the wall switch plate or wall
thermostat thoroughly to remove any dust
and oils. Affix the label to the surface of the
plate of the wall switch that controls the
fireplace (Figure A) or the wall thermostat
(Figure B). Choose the language primarily
spoken in the home. If unknown, affix the
English language label.

2. If a remote control is used to control the

fireplace, locate the transmitter and clean
it thoroughly to remove any dust and oils.
Affix the label to the surface of handheld
transmitter (Figure C). Choose the language
primarily spoken in the home. If unknown,
affix the English language label.

3. If you are unable to locate the labels, please

contact IHP or your nearest IHP dealer to
receive additional safety instruction labels
free of charge.

Cat. No. H8024 Replacement Label Kit Étiquettes de remplacement, n° cat. H8024 Juego de etiquetas de repuesto - Nº de cat. H8024
NOTE: English is red text on clear label. French

and Spanish are white text on black label.

SAFETY LABEL DIAGRAMS DIAGRAMMES DES ÉTIQUETTES DE SÉCURITÉ DIAGRAMAS DE ETIQUETAS DE SEGURIDAD

Apposition des mises en garde relatives
à la sécurité d’utilisation

Votre foyer a été livré avec des étiquettes de
sécurité qui doivent être collées à côté des
dispositifs de contrôle du foyer. Une étiquette
de sécurité doit être collée sur la plaque
de l’interrupteur contrôlant l’allumage du
foyer (Figure A) ou sur le thermostat mural
(Figure B) et, le cas échéant, sur le boîtier de
la télécommande (Figure C). Les mises en
garde auraient dû être collées au moment de
l’installation initiale du foyer. Si ce n’est pas le
cas, prenez les étiquettes adhésives multilingues
fournies avec ces instructions et procédez
comme suit :

1. Repérez l’interrupteur ou le thermostat mural

qui contrôle le foyer (vérifiez que l’interrupteur
contrôle le fonctionnement du foyer en le
faisant basculer de Marche à Arrêt, et vice­versa). Nettoyez soigneusement la plaque
murale de l’interrupteur ou le thermostat
mural pour éliminer la poussière et les traces
de graisse ou d’huile. Collez l’étiquette sur la
surface de la plaque de l’interrupteur mural qui
contrôle le foyer (Figure A) ou du thermostat
mural (Figure B) . Choisissez la langue qui
est principalement parlée dans la résidence
du propriétaire. En cas de doute, collez
l’étiquette en anglais.

2. Si une télécommande est utilisée pour

contrôler le foyer, nettoyez la soigneusement
pour éliminer la poussière et les traces de
graisse ou d’huile. Collez l’étiquette sur
le boîtier de la télécommande (Figure C).
Choisissez la langue qui est principalement
parlée dans la résidence du propriétaire. En
cas de doute, collez l’étiquette en anglais.

3. Si vous ne parvenez pas à localiser les

étiquettes, s’il vous plaît contactez IHP ou
votre revendeur le plus proche pour recevoir
IHP étiquettes d’instructions de sécurité
supplémentaires gratuitement.

Remarqué : Le texte anglais est rouge sur un
support transparent. Le texte français et espagnol
est blanc sur un support noir.

Colocación de advertencias de
seguridad en operación

Su chimenea incluye etiquetas de instrucciones
de seguridad que deben colocarse en el punto
de operación y control de la chimenea. Se debe
colocar una etiqueta de instrucciones de seguridad
en la placa del interruptor de pared desde el cual
se enciende y se apaga la chimenea (Figura A)
o en el termostato de pared (Figura B) y en el
transmisor de control remoto (Figura C) si se
usa. Las advertencias ya deben haberse colocado
cuando se completó la instalación inicial de la
chimenea. Si no están colocadas en estos lugares,
encuentre las etiquetas adhesivas multilingües
proporcionadas con estas instrucciones y prosiga
de la siguiente manera:

1. Identifique el interruptor o el termostato de

pared que controla la chimenea (verifique
que el interruptor opera la chimenea
encendiéndola y apagándola). Limpie bien
la placa del interruptor o el termostato de
pared para quitar el polvo y aceite. Pegue
la etiqueta en la superficie de la placa
del interruptor que controla la chimenea
(Figura A) o en el termostato de pared
(Figura B). Seleccione el idioma que más se
habla en la casa. Si no sabe cuál es, use la
etiqueta en inglés.

2. Si se usa un control remoto para controlar

la chimenea, encuentre el transmisor y
límpielo bien para quitar el polvo y aceite.
Pegue la etiqueta en la superficie del
transmisor (Figura C). Seleccione el idioma
que más se habla en la casa. Si no sabe cuál
es, use la etiqueta en inglés.

3. Si usted es incapaz de localizar las etiquetas,

por favor póngase en contacto con IHP,
o con su distribuidor más cercano IHP
recibir instrucción etiquetas de seguridad
adicionales sin costo.

Nota: La etiqueta en inglés es transparente con
texto rojo. Las etiquetas en francés y español son
negras con texto blanco.

Illustrations are for example only.
Your accessories may be different.

Les illustrations sont par exemple
uniquement. Vos accessoires
peuvent être différents.

Las ilustraciones son sólo ejemplos.
Tu accesorios pueden ser diferentes.

Figure A
Figura A

Innovative Hearth Products

PRG

On

Remote

Off

Figure B
Figura B

Figure C
Figura C

55

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Burn-in Period

The first few times this fireplace is operated, there will be an odor from the curing of paint and the burning off of the
lubricants used in the manufacturing process. Depending on usage, the burn-in period may take a few hours or a
few days.

NOTE: Ventilate the site during the burn-in period. The resulting odor and haze may set off a smoke detector. Do not
operate the blower during the burn-in period.

A white film may develop on the glass front during the first few fires as part of the burn-in period. The glass
should be kept clean during the burn-in period to prevent the film from baking on—making it very difficult to
remove (Cleaning the glass door on Page 63).

Accessing the Control Compartment

NOTE: If the door is difficult to open/close, remove it as instructed and straighten the door tabs (Figure 46).
NOTE: In contemporary fireplaces, remove the Facade and Facade panel. (Page 46).

1. Access the control compartment (Figure 34) by holding the control compartment door by the top and gently

lifting it up, then rotating it away from the fireplace.

Closing the Control Compartment

1. Swing the door gently up and then lift and set the door so it catches in the upright, closed position.

Removing the Control Compartment Door

Operation

900285-00 05/2015

Gas Controls

1. Remove the bottom, left screw (Figure 45) inside the control compartment securing the control compartment

door. Retain the screw for later reinstallation.

2. Position the left side door tab (Figure 46) out of the tab groove and align it with the vertical slot (Figure 45).

Figure 45: Control compartment door slots Figure 46: Control compartment door tabs

Vertical

slot

Screw
hole

Tab

groove

Tab pivot

hole

Door
tabs

3. Lift the left side of the control compartment door with the tabs in the vertical slot until the tabs clear the slot,
disengaging the left side of the door from the fireplace.

4. Pull the door to the left to disengage the right side door tabs, and remove the door. Store the control
compartment door in a secure location until reinstallation.

56

The standard controls for fireplace operation are located in the control compartment, below the glass door
(Figure 34). Optional control switches are also available.

Millivolt and electronic gas control systems operate differently. Before lighting and operating the fireplace determine
if it is a millivolt or electronic system:

• Millivolt Fireplaces (Figure 1)

• Electronic Fireplaces (Figure 2)

Familiarize yourself with the gas control valve and the lighting procedure (Page 70).

Millivolt Fireplaces

Detailed lighting instructions are found on Page 70. Also, millivolt fireplace lighting instructions are found on the
pull-out lighting instructions attached to the gas control valve.

When the pilot is lit, the main burner can be turned ON/OFF using a wall switch, remote control, optional on-unit
rocker switch (FRS), or wall thermostat.

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Electronic Fireplaces

Operation

900285-00 05/2015

If the millivolt fireplace is equipped with an optional remote switch (wall switch, remote control, rocker switch, or
wall thermostat) and the pilot is lit, the fireplace main burner can be turned ON/OFF using the optional switch.

NOTE: Do NOT wire more than one valve to the burner control switch. This will help prevent excessive resistance in
the burner circuit, that can cause burner operation problems.

Detailed lighting instructions are found on Page 72. Also, electronic fireplace lighting instructions are found on the
pull-out lighting instructions attached to the gas control valve.

If the electronic fireplace is equipped with an optional remote wall switch or remote control, the fireplace main
burner can be turned ON/OFF with the wall switch or remote control.

If the electronic fireplace is not equipped with a wall switch or remote control, the main burner must be turned ON/
OFF with a gas control switch installed separately. Contact the installer for more information. Check the batteries, if
installed, at least every three (3) months to ensure they are properly charged.

To light the fireplace in a power outage:

1. Confirm that batteries are installed in the battery pack.

2. Set the unit-mounted switch, or wall switch to the ON Position.

3. The unit should spark at the pilot and light.
NOTE: If there is no spark turn unit to off position, replace

the batteries, and repeat steps 1-3 above.

4. Operate the fireplace normally.

Installing the Backup Batteries

With a battery backup, electronic fireplaces can automatically switch to battery power. In the event of a power outage, this
allows ON/OFF operation (without blower functionality). Install new batteries before every burn season.

1. Open the control compartment (Page 56), and locate the battery holder.

2. Install four (4) AA batteries in the battery holder.

3. Close the control compartment door.

Continuous Pilot Ignition Switch

Fireplaces with an electronic gas valve have a continuous pilot ignition (CPI) switch installed in the
control compartment.

This switch allows the pilot to be switched from intermittent mode to continuous mode:

• Intermittent Mode—The pilot is extinguished when the fireplace is OFF.

• Continuous Mode—The pilot stays ON when the fireplace is OFF.
In periods of extreme cold, condensation may form on the glass door when the fireplace is OFF and the pilot is in

intermittent mode. Also, with the pilot in intermittent mode, the fireplace may cycle startup (i.e., the pilot and burner ignite,
but the burner extinguishes and reignites several times until the flue reaches the temperature for proper drafting).

• To save energy—switch to intermittent mode.

• For a standing pilot that will help prevent glass door condensation and cycle startup—switch to continuous mode.

NOTE: Continuous mode is indicated by a pilot that comes ON and remains lit when the fireplace is OFF.

Installing the Firebox Liners

1. Remove the three (3) optional firebox liner panels from the packing materials if purchased.

2. Carefully position the rear panel, upper edge first, in the firebox against the rear wall.

3. While holding the rear panel, carefully position the left side panel in the firebox.

4. Carefully position the right side panel in the firebox.

NOTE: Do not force the panels. Excessive force may cause breakage. If the panels are correctly positioned, they will fit snugly in

place.

57

Innovative Hearth Products
Superior

TM

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Installing the logs, volcanic stone, and glowing embers

WARNING

• Turn OFF all gas and electricity to the appliance before installing the volcanic stone, embers, and logs.

• Do NOT install the logs until the appliance has been competely installed, the gas line connected and
tested for leaks, and the initial burner operation has been confirmed.

• Use of an unapproved log set in the fireplace will void the warranty and will result in incomplete
combustion, sooting, and poor flame quality.

• Logs get very hot and remain hot for up to one hour after the gas supply is turned OFF. Handle the logs
only when cool.

• This appliance is not designed to burn wood. Any attempt to do so could cause irreparable damage to
appliance and prove hazardous.

• If the logs are not installed according to these instructions, improper combustion could occur. This could
result in the excessive production of soot and/or the colorless, odorless, toxic gas carbon monoxide (CO).

NOTE: Install the firebox liner before placing the stone. Logs can be installed after the volcanic stone.

Installing the volcanic stone, and glowing embers

1. If necessary, remove the glass door (Page 61).

2. In contemporary fireplaces, install glass media in recessed areas between front and rear floors. In 35” fireplaces
use less than one bag. The 40” contemporary models require a full bag. Spread the glass in a thin layer

evenly over the burner. Leave the pilot area open and take care to not allow crushed glass to fall into the pilot
hole.

NOTE: Do not mound the media or pile at rear of burner blocking air holes (see Figure 49).

3. In traditional units, spread the decorative volcanic stone in a pleasing pattern on the firebox floor along the slope

and to the back right and left sides of the burner (Figure 47).

Operation

NOTE: Do not place stone on the burner.

4. In traditional units, separate and fluff the glowing embers into pieces approximately the size of a quarter

(Figure 48).

Figure 47: Installing the volcanic stone Figure 48: Separating the glowing embers

5. In traditional units, position the separated glowing embers over the small holes on the burner surface
(Figure 49). Do NOT cover the large burner slots.

Figure 49: Installing the glowing embers

NOTE: Enough glowing ember

Air

Holes

Air

Holes

material is provided for
several applications. For best
glowing effect, replace the
ember material annually.

58

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

NOTE:

Installing the 33” and 35” logs

The logs have notches/tabs to assist proper positioning. Upper logs rest on lower logs via notches/tabs. Proper log
placement is critical to prevent sooting. Place the logs in the gaps between flame peaks, so they do not impinge the
flames. Follow the log placement instructions precisely.

NOTE: Do not cover the burner ports.
NOTE: Ensure the left front log (1) and right front log (2) are correctly installed on the burner positioning pins.

Table 38: 33 and 35 Log Set

4

2

Operation

900285-00 05/2015

1

3

5

Catalog number for the entire set:
33”: F1830
35”: F1884

Log Number Description

1 Rear Log
2 Left Front Log
3 Right Front Log
4 Left Cross Log
5 Right Cross Log

1. If necessary, remove the glass door (Page 61). Locate and bend up Burner Locating Tabs (Figure 50).

2. Locate the log placement brackets (Figure 50). Place embers and other media (see Page 58).

Figure 50: Locating the log placement brackets Figure 51: Placing log 1 and 2

Left Log Bracket (front & rear)

Right Log Bracket (front & rear)

1

2

Left and Right Burner Locating Tabs

3. Align the notches in the bottom of the rear log (1) with the left rear brackets (Figure 51).

4. Position the left rear log (1) on the left rear bracket and the left front log (2) on the left front log bracket and the

left burner locating tab (Figure 51).

Figure 52: Placing log 3 Figure 53: Placing log 4 and 5

4

5

3

5. Position the right front log (3) on the right front log bracket and right burner locating tab (Figure 52).

6. Position the left cross log (4) on the left rear log (1) and right cross log (5) on the right rear log bracket

(Figure 53).

NOTE: Fireplace shown with optional brick panels.

59

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installing the 40” and 45” logs

The logs have notches/tabs to assist proper positioning. Upper logs rest on lower logs via notches/tabs.
Proper log placement is critical to prevent sooting. Place the logs in the gaps between flame peaks, so they
do not impinge the flames. Follow the log placement instructions precisely.

NOTE: Do not cover the burner ports.

Table 39: 40” Log Set

4

2

1. If necessary, remove the glass door (Page 61).

2. Locate the log placement brackets (Figure 54).

Operation

900285-00 05/2015

1

5

Catalog number for the entire set:
40”: F1830

3

45”: F1884

Log Number Description

1 Rear Log
2 Left Front Log
3 Right Front Log
4 Left Cross Log

5 Right Cross Log

Figure 54: Placing log 1 Figure 55: Placing logs 2 and 3

Right Rear Log Bracket

1

Volcanic Stone

(Do not place glowing embers over burner slots)

Glowing Embers

2

Log Rack

3

3. Position rear log (1) on the left rear log bracket (Figure 54)

4. Position the left front log (2) and the right front log (3) against the log rack (Figure 55).

5. Position the left cross log (4) over the rear log (1) and left front log (2) with the front resting on the log rack

(Figure 56).

Figure 56: Placing log 4 Figure 57: Placing log 5

4

1

5

60

2

6. Position the right cross log (5) on the right rear log bracket and over right front log (3) (Figure 57).

NOTE: Fireplace shown with optional brick panels and volcanic stone installed.

3

Innovative Hearth Products

TM

Superior

Installing and removing the glass door

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

WARNING

• Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass.

• Handle this glass with extreme care! Glass is susceptible to damage—Do not scratch or handle roughly
while reinstalling the glass door frame.

• The glass door of this appliance must only be replaced as a complete unit as provided by the
manufacturer. Do not attempt to replace broken, cracked or chipped glass separately.

• Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use.

WARNING

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and
shall be installed.

WARNING

Une barrière conçue pour réduire le risque de brûlure par le hublot chaude est fournie avec l’appareil et doit
être installé.

WARNING

Do not operate appliance with the glass front removed, cracked, or broken.

AVERTISSEMENT

Ne pas utiliser l’appareil si le panneau frontal en verre n’est pas en place, est craqué, ou brisé.

WARNING

Any safety screen or guard removed for servicing the appliance must be replaced prior to operating
the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré pour permettre l’entretien de l’appareil doit être remis en place avant de
mettre l’appareil en marche.

Only doors certified with the fireplace shall be used.

Seules des portes certifiées pour cet appareil doivent être utilisées.

CAUTION

Do NOT abuse the glass door by striking it or slamming it shut.

61

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installing the glass door

1. Visually inspect the gasket on the backside of the glass door.

2. Position the door in front of the firebox opening with the bottom of the door held away from the fireplace at a

3. Let the bottom of the glass door swing gently in towards the fireplace ensuring that the gasket seats evenly as

4. Install the barrier.

5. Close the control compartment door.

Removing the glass door

1. Open the control compartment door in traditional models (Page 56).

2. Remove the barrier. Place the barrier in a safe location for later reinstallation.

3. Detach the two (2) door latches beneath the firebox floor.

4. Swing the bottom of the glass door away from the fireplace to a 45° angle (Figure 58)

5. Carefully grip the door at the top and bottom, and remove it from the fireplace. Place the door in a safe location

Operation

900285-00 05/2015

NOTE: The gasket surface must be clean, free of irregularities, and seated firmly. Ensure it is properly located.
Make sure the bead is not rolled into the channel at the top of the door, but remains flat against the top of
the glass.

45° angle (Figure 58). Hook the top flange of the door frame over the top of the firebox frame.
NOTE: Ensure the glass door is centered—with even spacing on each side.

the door draws shut. Securely fasten the two (2) latches beneath the firebox floor to the door V-flange.

NOTE: In contemporary models, remove facade panel and base first.

NOTE: If necessary, remove the door and place it in a safe location for later reinstallation.

for later reinstallation.

Figure 58: Glass Door

Glass

Door

Control

Compartment

Door

Hood

Latch

NOTICE: All DRT/C3000 model
fireplaces include a barrier to
reduce the risk of burns from hot
viewing glass. This barrier in
the fireplace is a screen shown
below

33” Barrier F1902
35” Barrier F1839
40” Barrier F1840
45” Barrier F1903

62

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

MAINTENANCE

Operation

900285-00 05/2015

Refer to the Maintenance Schedule on Page 65 for maintenance tasks, procedures, frequency, and a listing of by
whom the tasks should be performed. Always verify proper fireplace operation after servicing.

WARNING

Turn OFF gas and electrical power to the fireplace and allow it to cool before cleaning or
servicing the appliance.

CAUTION

Wear gloves and safety glasses for protection while doing required maintenance.

Verify proper operation after servicing.

S’assurer que l’appareil fonctionne adéquatement une fois l’entretien terminé.

Always turn OFF gas before cleaning. Before relighting, refer to the lighting instructions in this manual.
Instructions are also found on a pull-out panel located in the control compartment.

Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids.
NOTE: Prior to the first use of the fireplace and each burn season and periodically during the burn season, inspect the

horizontal termination for debris such as bird nests, leaves, paper or branches. Remove any items from the surfaces of the
termination prior to use. Also be aware of shrubs and plantings that may encroach on the termination.

Inspecting the venting system

The fireplace and venting system should be thoroughly inspected before initial use and at least annually by a qualified
service technician. Inspection should include ensuring that exhaust or intake passages are unobstructed and vent
components are properly assembled and not damaged.

The homeowner must contact a qualified service technician at once if any abnormal condition is observed.

If the venting system is disassembled for any reason, a qualified service technician should follow vent installation
instructions for proper reassembly and proper sealing of the venting system components. However, more frequent
periodic inspections and cleanings should be performed by the homeowner.

NOTE: Prior to the first use of the fireplace and each burn season and periodically during the burn season,
inspect the horizontal termination for debris such as bird nests, leaves, paper or branches. Remove any items
from the surfaces of the termination prior to use. Also be aware of shrubs and plantings that may encroach on
the termination.

Inspecting the burner flame appearance

Periodically inspect the burner and pilot flame. Ensure that the burner flame appearance resembles the flame shown
in Figure 39 on Page 43 and as described in Flame Appearance and Sooting on Page 42. Any necessary
burner flame adjustments must be performed by qualified personnel only (Page 42). Refer to Page 41 for more
information about the pilot flame appearance. Contact a qualified service technician at once if any abnormal condition
is observed.

Cleaning the glass door

Do not use abrasive cleaners on glass. Never clean the glass when it is hot.

CAUTION

Clean the glass during the Burn-in Period, and then only when necessary and when the fireplace is cool. Wipe the
surface with a clean, dampened, soft cloth. Follow with a dry, soft towel as desired. Take care not to scratch the glass
surface. Periodically, remove any build-up caused by the following:

• During start-up, it is normal for condensation to form on the inside of the glass (this condensation and fog will
usually disappear in a few minutes). The moisture can cause lint, dust and other airborne particles to cling to the
glass surface.

• Initial curing of the high temperature paint and burning off of lubricants used in the manufacturing process may
result in a film on the glass.

• A white coating may form on the glass as a result of impurities and minerals in the fuel.

Clean the glass two or three times each heating season, depending on the circumstances present. The following
cleaning solutions are approved for use:

• Non-ammonia based glass cleaner

• 50/50 mixture of white vinegar / water

• Gas fireplace/stove glass cleaner

63

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Inspecting the glass gasket

Visually inspect the gasket on the backside of the glass door. The gasket surface must be clean, free of irregularities,
and seated firmly.

Cleaning the control compartment

Keep the control compartment clean by vacuuming or brushing it out at least twice a year. More frequent cleaning
may be required due to excessive lint from carpeting, bedding material, etcetera. It is imperative that control
compartments, burners and circulating air passageways of the appliance be kept clean.

Touching up paint in small areas

Only use a factory-supplied paint kit for any touch-ups. Paint is available at your local IHP dealer. Never attempt
to paint a hot fireplace. Do not attempt to repaint the fireplace until the finish is completely cured (Burn-in Period on

Page 56). If the surface becomes stained or marred, it may be lightly sanded and touched up.

Logs

Removing and cleaning the logs

The fiber logs become very fragile after curing.

Carefully remove the logs. Clean carbon from the logs using a vacuum cleaner, or a soft bristle brush (e.g., paint brush).

Reinstalling the embers and logs

Operation

900285-00 05/2015

CAUTION

Carefully follow the placement instructions (Page 58). All logs should fit onto the corresponding pins and/or log
stoppers. This will ensure proper flame and safe combustion.

NOTE: Improper positioning of logs can create carbon build-up and will alter the performance of the fireplace.

Replacing the logs

If the logs become damaged and need replacement, use only the proper replacement logs from manufacturer (Page 78).

Cleaning the burner

Carefully remove the logs/media. Vacuum out any foreign matter on the burner (e.g., lint, carbon, etc.). Ensure the
burner ports are free of debris.

NOTE: Improper positioning of logs/media can create carbon build-up and will alter the performance of the fireplace.

Inspecting the wiring

Refer to the wiring diagram (Figure 30, Figure 31, and Figure 32).

When servicing controls, label all wires prior to disconnection. Wiring errors can cause
improper and dangerous operation. Verify proper operation after servicing.

CAUTION

ATTENTION

64

Au moment de l’entretien des commandes, étiquetez tous les fils avant de les débrancher.
Des erreurs de cáblage peuvent entraîner un fonctionnement inadéquat et dangereux.

Inspect and clean all wire connections. Ensure that there is no wire melting or damage. The inspection
should include:

• Terminals at the valve

• ON/OFF switch

• Optional wall thermostat, remote control, or wall switch

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

MAINTENANCE SCHEDULE

See the tables below for detailed information about required maintenance, both regular and annual.

Table 40: Maintenance Performed Annually—Before the Burning Season

Maintenance Task Performed By Procedure

Inspecting/Cleaning Burner, Logs
and Controls

Checking Flame Patterns and
Flame Height

Inspecting/Cleaning Pilot and Burner Qualified Service Technician Remove any surface build-up on pilot and

Checking Vent System Qualified Service Technician Inspect the vent system at the top and at

Fireplace Inspection Qualified Service Technician Perform the appropriate fireplace inspection

Replacing Glowing Embers Homeowner/Qualified Services Technician Remove the old glowing embers and

Replacing Batteries Homeowner/Qualified Services Technician Replace all batteries in the battery holders.

Qualified Service Technician Inspect valve and ensure it is properly

operating. Check piping for leaks. Vacuum
the control compartment, fireplace logs and
burner area.

Qualified Service Technician Verify the flame pattern and height displayed

by the fireplace (Figure 39). Flames must not
impinge on the logs.

burner assembly. Wipe the pilot nozzles,
igniter/flame rod and hood. Ensure the pilot
flame engulfs the flame sensor as shown.

the base (within the firebox) for signs of
blockage or obstruction. Look for any signs
of dislocation of the vent components.

procedure detailed in this manual.

vacuum the area. Place new glowing embers
(Figure 48).

Table 41: Maintenance Performed Periodically—After the Burning Season

Maintenance Task Performed By Procedure

Cleaning Firebox Interior Homeowner Carefully remove logs, volcanic stone and

glowing embers / glass media. Vacuum out
interior of the firebox. Clean firebox walls and
log grate, if installed. Replace removed items
as detailed in this manual.

Check Flame Patterns and Flame Height Homeowner Verify the flame pattern and height displayed

by the fireplace (Figure 39). Flames must not
impinge on the logs.

Checking Vent System Homeowner Inspect the vent system at the top and at

the base (within the firebox) for signs of
blockage or obstruction. Look for any signs
of dislocation of the vent components.

Cleaning Glass Door Homeowner Clean as necessary following the directions

provided in this manual (Page 63). Do not
touch or attempt to clean the glass while hot.

ACCESSORY COMPONENTS
Touch-Up Paint Kits

Repair minor scratches and discoloration of the fireplace black painted surfaces with the touch-up paint kits.

Table 42: Touch-Up Paint Kit

Catalog No. Description

F1881 Firebox interior touch-up paint
F1882 Chassis touch-up paint

65

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

ACCESSORY COMPONENTS (CTD.)
Forced Air Kits

The FBK-100 blower provides constant velocity forced air circulation. The FBK-200 assembly with variable speed,
wall-mountable switch provides variable speed forced air circulation. The FBK-250 offers variable speed control and
a heat-activated switch; perfect for fireplaces controlled thermostatically.

Table 43: Forced Air Kits

Glowing Embers and Volcanic Stone

Table 44: Glowing Embers and Volcanic Stone

Brickaded Firebox Liner Kits

Operation

900285-00 05/2015

Catalog Model Description

80L84 FBK-100 Blower, Standard (single speed)
80L85 FBK-200 Blower, Variable Speed (with wall-mounted switch)
H7841 FBK-250 Blower, Variable Speed (with thermal snap switch)

Catalog Model Description

88L53 FGE Bag of Glowing Embers
80L42 FDVS Bag of Volcanic Stone

Table 45: Ceramic Fiber Liner Kits

Facade Units for Contemporary Fireplaces

Table 46: Contemporary Facade Units

Frame

Panel

Catalog Model Description Used on

F1887 MBLK33B Buff

33” ModelsF1886 ABLK33V Vintage Red
F2187 BLK33OTR-H Old Town Red Herringbone
F1827 MBLK35B Buff

35” ModelsF1825 ABLK35V Vintage Red
F2188 BLK35OTR-H Old Town Red Herringbone
F1828 MBLK40B Buff

40” ModelsF1826 ABLK40V Vintage Red
F2189 BLK40OTR-H Old Town Red Herringbone
F1889 MBLK45B Buff

45” ModelsF1888 ABLK45V Vintage Red
F2190 BLK45OTR-H Old Town Red Herringbone

35” Models 40” Models

Description Catalog No. Model No. Catalog No. Model No.

Base

Façade Base Black F2460 FBBK35CD F2462 FBBK40CD

66

Trim

Façade Base
Stainless

Façade Panel and
Trim Black

Façade Panel and
Trim Stainless

F2461 FBSS35CD F2463 FBSS40CD

F2464 FPBK35CD F2466 FPBK40CD

F2465 FPSS35CD F2467 FPSS40CD

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Termination Guard Kits

The vent termination guards may be used to minimize exposure to the hot surface of the termination.

Table 47: Termination Guard Kits

Deluxe

Termination

Shroud

(fits H1968)

Termination

Guard

(fits 94L10

and H1968)

Thermostatic Control Kits

Feature a thermostatic ON/OFF mode as well as manual ON/OFF operation.

Table 48: Thermostatic Control Kits

RC-S-STAT, Thermostatic or manual operation Catalog Number

Catalog Model Description

Square

Termination

Guard

(fits 94L10

and H1968)

H5820 4.5HTSK Termination Shroud
87L02 SV4.5HGS Termination Guard, Deluxe

17M52 SV4.5HGS-1 Termination Guard, Square

• LCD display

• Receiver wall-mounted or placed in the
valve compartment

• Up to 9-hr countdown timer

• Child lock

• Low battery indicator

• Batteries included

Operation

900285-00 05/2015

H8861

RC-S-Touch, State-of-the-art control with touch screen operation Catalog Number

• Backlit LCD display

• Transmitter wall-mounted docking station

• Receiver wall-mounted or placed in the
control compartment

• Thermostatic or manual ON/OFF operation

• Programmable weekday/
weekend modes

• Flame icon

• Low battery indicator

• Batteries included

H8865

WS-S-STAT, Wall control Catalog Number

• Large LCD display

• Shows room and set temperatures in
°F and °C

• Wall-mounted

• Thermostatic or manual
ON/OFF operation

• Connects to wall
switch wire

H8864

67

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

ON/OFF and Timer Control Kits

Feature a timed ON/OFF mode as well as manual ON/OFF operation.

Table 49: ON/OFF and Timer Control Kits

G-Fire, Cost Effective Solution Catalog Number

RC-S-1, Manual or up to 3-hour timer modes Catalog Number

WS-S-TMR, Wall Control Catalog Number

• Manual ON/OFF operation

• Works with millivolt and low voltage
electronic ignition controls

• Kit includes remote and receiver

• LCD display

• Shows room temperature in °F and °C

• Wall clip included

• Receiver wall-mounted or placed in the
control compartment

• 4-button timer with 30/60/120/OFF minutes

• Wall-mounted

• Perfect for rental and resort applications

• Connects to wall switch wire

• White face plate included

• Flame icon

• Low battery indicator

• Batteries included

Operation

900285-00 05/2015

H8840

H8860

H8863

Unit-Mountable Rocker Switch Kit

This rocker switch kit can be installed directly in the control compartment to provide ON/OFF operation in lieu of a
wall switch.

Table 50: Unit-Mountable Rocker Switch

OFF/ON Wall Switch Kit

The OFF/ON wall switch kit can be used to control the operation of the fireplace burner or blower. Install the OFF/ON
wall switch in a convenient location near the fireplace.

Table 51: OFF/ON Wall Switch Kit

Catalog Model

80L41 FRS

Catalog Model

85L87 FWSK

68

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Variable Speed Wall Switch Kit

The variable speed wall switch kit provides variable speed control if the optional FBK-100 blower kit is installed.

Table 52: Variable Speed Wall Switch Kit

Glass Media Kits

Table 53: Glass Media

NOTE: No more than one 5 lb. bag should be used in the fireplace.

Operation

900285-00 05/2015

Catalog Model

045571H VSWS

Catalog Model Description

H8412 CRSHGL-RBLK Bag of Glass Media, Reflective Black
H8424 CRSHGL-RBLU Bag of Glass Media, Reflective Blue
H8413 CRSHGL-P Bag of Glass Media, Platinum
H8538 CRSHGL-GF Bag of Glass Media, Goldfinger
H8539 CRSHGL-C Bag of Glass Media, Copper

69

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Operation

900285-00 05/2015

LIGHTING INSTRUCTIONS

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.

A. This appliance has a pilot which must be lighted by a piezo igniter. When

lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to

smell next to the floor because some gas is heavier than air and will settle
on the floor.

WHAT TO DO IF YOU SMELL GAS:

• Donottrytolightanyappliance.

• Donottouchanyelectricswitch;donotuseanyphoneinyourbuilding.

1. STOP! Read the safety information above on this label.

2. (If applicable) Set the thermostat to lowest setting. Turn wall on/off
switch, unit mounted on/off switch or remote control switch "OFF."

3. Turn OFF all electric power to the appliance.

4. Access the control compartment.

5. Push in gas control knob slightly and turn clockwise to "OFF."

NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is

pushed in slightly. Do Not force.

6. Wait five (5) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow "B" in the
safety information above on this label. If you don't smell gas, go to the
next step.

7. Find pilot - located in firebox on the same plane as the top of the burner.

8. Turn knob on gas control counterclockwise to "PILOT."

9. Push in control knob all the way and hold in. Immediately light the pilot
by triggering the piezo igniter (pushing the button) until pilot lights.
Continue to hold the control knob in for about 1-1/2 minutes after the
pilot is lit. Release knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 9.

• Ifknob does not pop up when released, stop and immediately call

your service technician or gas supplier.

1. (If applicable) Set the thermostat to lowest setting. Turn wall on/off

switch, unit mounted on/off switch or remote control switch "OFF."

2.

Turn OFF all electric power to the appliance, if service is to be
performed.

3.

Access the control compartment.

FOR YOUR SAFETY READ BEFORE LIGHTING

• Immediatelycall your gas supplier from a neighbor’sphone.Followthegas
supplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthefiredepartment.

C. Use only your hand to push in or turn the gas control knob. Never use tools.

If the knob will not push in or turn by hand, don’t try to repair it, call a

qualified service technician. Force or attempted repair may result in a fire or
explosion.

D. Do not use this appliance if any part has been under water. Immediately call

a qualified service technician to inspect the appliance and to replace any
part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

• If the pilot will not stay lit after several tries, turn the gas control

knob to "OFF" and call your service technician or gas supplier.

10. Turn gas control knob counterclockwise to "ON."

11. Close control compartment.

12. (If applicable) Turn on all electrical power to the appliance.

13. (If applicable) Set thermostat to desired setting. Turn wall on/off switch,

unit mounted on/off switch or remote control switch "ON."

Gas Control Valves

N

O

T

O

it

L

I

SIT

Robertshaw

Honeywell

P

O

F

F

OUT

IN

Gas Control Knobs

ON

PILOT

OFF

IN OUT

PILOT

H

I

O

L

TO TURN OFF GAS TO APPLIANCE

4.

Push in gas control knob slightly and turn clockwise to "OFF."
Do not force.

5. Close the main line gas shut-off valve.

6. Close control compartment.

Millivolt Gas Valve

Pilot Assemblies

T

O

L

I

P

O

W

L

H

I

HI

LO

N

O

TPTH TP TH

F

T

F

O

O

L

I

P

70

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.

P/N 900327-00 Rev. 0

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un
incendie ou une explosion entraînant des dommages, des blessures ou la mort.

A.Cet appareil est muni d’une veilleuse qui doit être allumée avec un allumeur

piézo-électrique. Respectez les instructions ci-dessous à la lettre.

B. AVANT L’ALLUMAGE: Avant d’allumer la veilleuse, reniflez tout autour de

l’appareil pour déceler une odeur de gaz. Reniflez près du plancher, car certains
gaz sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Nepastenterd’allumerd’appareil.

• Netouchez à aucun interrupteur ; ne pas vous servirdestéléphonessetrouvant

dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez

1. ARRÊTEZ ! Lisez les instructions de sécurité sur la portion supérieure de
cette étiquette.

2. (Si applicable) Réglez le thermostat à la température la plus basse. Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance à
"OFF. "

3. Coupez l’alimentation électrique de l’appareil.

4. Accédez au compartiment de contrôle.

5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans le sens des
aiguilles d’une montre jusqu’à la position d’arrêt “OFF”.

Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à

moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.

6. Attendre cinq (5) minutes pour laisser échapper tout le gaz. Reniflez tout
autour de l’appareil, y compris près du plancher, pour déceler une odeur
de gaz. Si vous sentez une odeur de gaz, ARRÊTEZ ! Passez à l’étape B des
instructions de sécurité sur la portion supérieure de cette étiquette. S’il n’y a
pas d’odeur de gaz, passez à l’étape suivante.

7. Trouver le pilote –

brûleur.

8. Tournez le bouton de contrôle sur la valve à gaz dans le sens antihoraire

vers "Pilote".

9. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé. Allumez
immédiatement la veilleuse en déclenchant l’allume-gaz à étincelle (en
poussant le bouton) jusqu’à ce que la veilleuse s’enflamme. Continuez
de tenir le bouton de réglage enfoncé pendant environ 90 secondes après
l’allumage de la veilleuse. Relâchez le bouton et il sortira subitement. La
veilleuse devrait rester allumée. Si

inclusivement.

1. (Si applicable) Réglez le thermostat à la température la plus basse. Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance à
"OFF. "

2.

Coupez l’alimentation électrique de l’appareil s’il faut procéder à l’entretien.

3.

Accédez au compartiment de contrôle.

POUR PLUS DE SÉCURITÉ, LIRE AVANT D’ALLUMER

INSTRUCTIONS D’ALLUMAGE

Situé dans l’âtre sur la même surface que le dessus du

elle s’éteint, répétez les étapes 5 à 8

COMMENT COUPER L’ADMISSION DE GAZ DE L’APPAREIL

900285-00 05/2015

les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur, appelez le service des

incendies.

C. Ne pousser ou tourner la manette d’admission du gaz qu’à la main. Ne

jamais employer d’outil à cette fin. Si la manette reste coincée, ne tentez

pas de la réparer; appelez un technicien qualifié. Quiconque tente de

forcer la manette ou de la réparer peut provoquer une explosion ou un
incendie.

D. N’utilisez pas cet appareil s’il a été plongé dans l’eau, même

partiellement. Faites inspecter l’appareil par un technicien qualifié et
remplacez toute partie du système de contrôle et toute commande qui ont
été plongés dans l’eau.

• Sila manette ne se soulève pas d’elle-même lorsqu’on la relâche,

arrêter et appeler immédiatement un technicien qualifié ou le
fournisseur de gaz.

• Si la veilleuse ne reste pas allumée après plusieurs tentatives,

réglez la manette d’admission du gaz à la position OFF et appelez un
technicien qualifié ou le fournisseur de gaz.

10. Tournez le bouton de réglage du gaz en sens inverse des aiguilles d’une
montre jusqu’à sa position de marche “ON”.

11. Fermer le compartiment de contrôle.

12. (Si applicable) Mettez l’appareil sous tension.

13. (Si applicable) Réglez le thermostat à la température désirée.

Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance
à "ON."

Robertshaw

Honeywell

Vanne Gaz Millivolt

N

O

T

O

it

L

I

P

O

F

SIT

F

OUT

IN

Bouton de réglage du gaz

ON

PILOT

OFF

PILOT

H

I

O

L

T

O

L

I

P

O

W

L

H

I

HI

LO

IN OUT

F

T

F

O

O

L

I

P

N

O

Millivolt Pilot

TPTH TP TH

4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans le
sens des aiguilles d’une montre jusqu’à la position d’arrêt “OFF”.
Ne forcez pas le bouton.

5. Fermer la valve de gaz principale.

6. Fermer le compartiment de contrôle.

Operation

DANGER

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

L'écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de contact accidentel
avec la vitre chaude et doit être installé pour la protection Des enfants et Des personnes à risques.

P/N 900328-00 Rev. 0

71

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Electronic Gas Valve

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.

Operation

900285-00 05/2015

FOR YOUR SAFETY READ BEFORE OPERATING

A. This appliance is equipped with an ignition device which automatically lights

the pilot. Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to

smell next to the floor because some gas is heavier than air and will settle
on the floor.

WHAT TO DO IF YOU SMELL GAS:

• Donottrytolightanyappliance.

• Donottouchanyelectricswitch;donotuseanyphoneinyourbuilding.

• Immediately call your gas supplier from a neighbor’sphone.Followthegas
supplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthefiredepartment.

C. If any portion of this appliance does not operate as the instructions indicate,

do not try to repair it, call a qualified service technician. Do not use tools.
Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call

a qualified service technician to inspect the appliance and to replace any
part of the control system and any gas control which has been under water.

OPERATING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Read the Care and Operation manual including the section on "Remote Control
System," (if applicable).

3. Slide the switch on the receiver, wall switch or ON/OFF switch to "OFF."

4. Turn "OFF" all electric power to the appliance. Note: The control may have a
battery backup (remove batteries, if installed).

5. This appliance is equipped with an ignition device which automatically lights the
pilot. Do not try to light the pilot by hand.

6. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B” in the safety information above on this

label.Ifyoudon’tsmellgas,gotothenextstep.

7. Turn on all electric power to the appliance. Note: The control may have a battery
backup (install batteries, if applicable).

8. Slide the switch on the receiver to REMOTE or ON/OFF switch /wall switch to ON.

9. (if applicable) Press ON/OFF button on remote control transmitter to "ON."

10. (if applicable)

11. If the appliance will not operate, follow the instructions "To Turn Off Gas To
Appliance" and call your service technician or gas supplier.

Set thermostat on remote control to desired setting.

Electronic Gas Control

Valve - SIT

Electronic Pilot Assembly

TO TURN OFF GAS TO APPLIANCE

72

1.

Slide the switch on the receiver, wall switch or ON/OFF switch to "OFF.

2. (if applicable) Press ON/OFF button on remote control transmitter to
"OFF."

DANGER

3. Turn off all electric power to the appliance if service is to be performed.
Note: The control may have a battery backup (remove batteries, if
installed).

4. Close the main line gas shut-off valve.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.

P/N 900337-00, Rev. 0

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

POUR PLUS DE SÉCURITÉ LIRE AVANT DE METTRE EN MARCHE

AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un
incendie ou une explosion entraînant des dommages, des blessures ou la mort.

Operation

900285-00 05/2015

A. Cet appareil est muni d’un dispositif d’allumage qui allume

automatiquement la veilleuse. Ne tentez pas d’allumer la veilleuse
manuellement.

B. AVANT DE FAIRE FONCTIONNER, reniflez tout autour de l’appareil pour

déceler une odeur de gaz. Reniflez près du plancher, car certains gaz sont
plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se

trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les

instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies.

C. Si un élément de cette unité ne fonctionne pas tel que décrit dans les

instructions, n’essayez pas de le réparer, appelez un technicien qualifié.
N’utilisez-pas d’outils. Le fait de forcer la manette ou de la réparer peut
déclencher une explosion ou un incendie.

D. N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement.

Faites inspecter l’appareil par un technicien qualifié et remplacez toute partie
du système de contrôle et toute commande qui ont été plongés dans l’eau.

INSTRUCTIONS DE MISE EN MARCHE

1. ARRÊTEZ ! Lisez les avertissements de sécurité à l’endos de cette étiquette.

2. Lisez le manuel d’utilisation et d’entretien incluant la section
« Système de télécommande » (si applicable).

3. Placez l’interrupteur mural ou "on/off" en position "off."

4. Coupez l’alimentation électrique de l’appareil. Note: Le contrôleur peut avoir une batterie de
secours (retirer les batteries au besoin).

5. Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse. Ne
tentez pas d’allumer la veilleuse manuellement.

6. Attendre cinq (5) minutes pour laisser échapper tout le gaz. Reniflez tout autour de l’appareil,
y compris près du plancher, pour déceler une odeur de gaz. Si vous sentez une odeur de gaz,
ARRÊTEZ ! Passez à l’étape B des instructions de sécurité sur la portion supérieure de cette
étiquette. S’il n’y a pas d’odeur de gaz, passez à l’étape suivante.

7. Mettez l’appareil sous tension. Note: Le contrôleur peut avoir une batterie de secours (installer
les batteries au besoin).

8. Placez l’interrupteur du récepteur en position “REMOTE” (ou l’interrupteur mural en position ON).

9. (Si applicable)

10. (Si applicable) Ajustez le thermostat sur la télécommande à l’ajustement désiré.

11. Si l’appareil ne se met pas en marche, suivez les instructions intitulées « Comment couper
l’admission de gaz de l’appareil » et appelez un technicien qualifié ou le fournisseur de gaz.

Appuyez sur le bouton “ON/OFF” pour sélectionner “ON”.

Valve électronique -

Module de veilleuse

SIT

électronique

COMMENT COUPER L’ADMISSION DE GAZ DE L’APPAREIL

1. Placez l’interrupteur mural ou "on/off" en position "off."

2. (Si applicable) Sélectionnez OFF sur le récepteur.

DANGER

3. Coupez l’alimentation électrique de l’appareil s’il faut procéder à l’entretien.
Note: Le contrôleur peut avoir une batterie de secours (retirer les batteries au
besoin).

4. Fermer la valve de gaz principale.

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

L'écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de contact accidentel
avec la vitre chaude et doit être installé pour la protection Des enfants et Des personnes à risques.

P/N 900334-00, Rev. 0

73

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Electronic Gas Valve (Contemporary Fireplaces)

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.

Operation

900285-00 05/2015

A. This appliance is equipped with an ignition device which automatically lights

the pilot. Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to

smell next to the floor because some gas is heavier than air and will settle
on the floor.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

• If you cannot reach your gas supplier, call the fire department.

C. If any portion of this appliance does not operate as the instructions indicate,

D. Do not use this appliance if any part has been under water. Immediately call

OPERATING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Read the operation section of the Installation and Operation manual.

3. Turn the burner ON/OFF switch to "OFF."

4. Turn "OFF" all electric power to the appliance.

5. This appliance is equipped with an ignition device which automatically
lights the pilot. Do not try to light the pilot by hand.

6. Wait five (5) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow “B” in the
safety information above
next step.

7. Turn on all electric power to the appliance.

8. Turn the burner ON/OFF switch to ON. After approximately 4 seconds
the spark ignition system will spark for 60 seconds to light the main
burner.

9. If the appliance will not operate, follow the instructions "To Turn Off
Gas To Appliance" and call your service technician or gas supplier.

on this label. If you don’t smell gas, go to the

supplier’s instructions.

Force or attempted repair may result in a fire or explosion.

a qualified service technician to inspect the appliance and to replace any
part of the control system and any gas control which has been under water.

Electronic Pilot

Assembly

Copreci Gas

Valve

Switches

Intermittent/Standing Pilot
Mode Switch (on facade)

yellow wires

Flame Height (wall switch)

blue wires

Burner ON/OFF (wall switch)

brown wires

.sloot esu ton oD .naicinhcet ecivres deifilauq a llac ,ti riaper ot yrt ton od

74

TO TURN OFF GAS TO APPLIANCE

1. Turn the burner ON/OFF switch to "OFF."

2. Turn off all electric power to the appliance if service is to be

performed.

DANGER

3. Close the main line gas shut-off valve.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.

P/N 900426-00, Rev. 0

Innovative Hearth Products

9-5/8"

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

POUR PLUS DE SÉCURITÉ LIRE AVANT DE METTRE EN MARCHE

AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un
incendie ou une explosion entraînant des dommages, des blessures ou la mort.

Operation

900285-00 05/2015

A. Cet ap p a r eil est muni d’ u n dispositif d’allumage qui allume

automatiquement la veilleuse. Ne tentez pas d’allumer la veilleuse
manuellement.

B. AVANT DE FAIRE FONCTIONNER, reniflez tout autour de l’appareil pour

déceler une odeur de gaz. Reniflez près du plancher, car certains gaz sont
plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se

trouvant dans le bâtiment.

INSTRUCTIONS DE MISE EN MARCHE

1. ARRÊTEZ ! Lisez les avertissements de sécurité à l’endos de cette
étiquette.

2. Lire la section opération du manuel d’instructions et d’opération.

3. Mettre l’interrupteur du brûleur "ON/OFF" à « OFF ».

4. Coupez l’alimentation électrique de l’appareil.

5. Cet appareil est muni d’un dispositif d’allumage qui allume
automatiquement la veilleuse. Ne tentez pas d’allumer la veilleuse
manuellement.

6. Attendre cinq (5) minutes pour laisser échapper tout le gaz. Reniflez tout
autour de l’appareil, y compris près du plancher, pour déceler une odeur
de gaz. Si vous sentez une odeur de gaz, ARRÊTEZ ! Passez à l’étape B
des instructions de sécurité sur la portion supérieure de cette étiquette.
S’il n’y a pas d’odeur de gaz, passez à l’étape suivante.

7. Mettez l’appareil sous tension.

8. Mettre l’interrupteur du brûleur "ON/OFF" à « ON ». Attendre 4 secondes.
Le système d’allumage produira des étincelles pendant 60 secondes afin
d’amorcer le brûleur principal.

9. Si l’appareil ne se met pas en marche, suivez les instructions intitulées
« Comment couper l’admission de gaz de l’appareil » et appelez un
technicien qualifié ou le fournisseur de gaz.

• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les
instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies.

C. Si un élément de cette unité ne fonctionne pas tel que décrit dans les

instructions, n’essayez pas de le réparer, appelez un technicien qualifié.
N’utilisez-pas d’outils. Le fait de forcer la manette ou de la réparer peut
déclencher une explosion ou un incendie.

D. N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement.

Faites inspecter l’appareil par un technicien qualifié et remplacez toute partie
du système de contrôle et toute commande qui ont été plongés dans l’eau.

Module de veilleuse

électronique

Valve électronique -

Copreci

Interupteurs

Mode Intermittent/Veilleuse
en attente (sur la façade)

fil jaune

Élevée/faible brûleur (interrupteur mural)

fils bleue

MARCHE/ARRÊT du brûleur
(interrupteur mural)

fil marron

COMMENT COUPER L’ADMISSION DE GAZ DE L’APPAREIL

1. Mettre l’interrupteur du brûleur "ON/OFF" à « OFF »

2. Coupez l’alimentation électrique de l’appareil s’il faut procéder à
l’entretien.

DANGER

3. Fermer la valve de gaz principale.

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

L'écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de contact accidentel
avec la vitre chaude et doit être installé pour la protection Des enfants et Des personnes à risques.

P/N 900427-00, Rev. 0

75

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Operation

TROUBLESHOOTING

Before troubleshooting, ensure that the fireplace main line gas shutoff valve and the wall switch are in the ON position. The following
troubleshoots the fireplace only to an elementary level. For detailed remote and ignition system troubleshooting, refer to the
instructions provided with the remote.

Detailed valve system troubleshooting should only be performed by a qualified service technician.

Table 54: Troubleshooting Millivolt Systems

1. Spark igniter will

not light pilot after
repeated triggering of
igniter button.

WARNING: if the
pilot will not light
after 1 minute of
attempting, wait for
at least 5 minutes for
gas to clear before
attempting again.

2. Pilot will not stay

lit after carefully
following the lighting
instructions.

3. Pilot burning, no

gas to burner, Valve
knob “ON,” and the
(standard) burner
OFF/ON switch is ON.

NOTE: If an optional*
remote switch is used
for burner operation,
if the standard burner
OFF/ON switch is still
installed on fireplace
it must be in the OFF
position.

4. Frequent pilot/burner

outage problem.

* Optional remote switch kits—wall switch, wall thermostat or remote control.

a. Defective igniter (no spark at electrode). Check for spark at electrode and pilot; if no spark and

electrode wire is properly connected, replace igniter.

b. Defective or misaligned electrode at pilot

(spark at electrode).

Using a match, light pilot. If pilot lights, turn off pilot
and trigger the igniter button again. If pilot lights, an
improper gas mixture caused the bad lighting and
a longer purge period is recommended. If pilot will
not light – check gap at electrode and pilot – should
be 1/8” to have a strong spark. If gap measures 1/8”,
replace pilot.

c. Gas supply pressure errant. Check inlet gas pressure. It should be within the limits

as marked on the rating plate.

d. Pilot orifice plugged. Clean or replace pilot orifice.
a. Defective pilot generator (thermocouple). Check pilot flame, it must impinge on thermocouple.

Clean and/or adjust pilot for maximum flame
impingement on thermocouple. Ensure that the
connection between the valve and thermocouple are
tight and secure.

a. Wall switch or wires defective. Check wall switch and wires for proper connections.

Jumper wire across terminals at wall switch, if burner
comes on, replace defective wall switch. If okay,
jumper wires across wall switch wires at valve, if
burner comes on, wires are faulty or connections
are bad.

b. Thermopile may not be generating

sufficient millivolts.

Check thermopile with millivolt meter. Take reading
at thermopile terminals of gas valve. Should read
325 millivolts minimum with optional wall switch
OFF. Replace faulty thermopile if reading is below
specified minimum.

c. Plugged burner orifice. Check burner orifice for blockage and remove.
d. OFF/ON Switch and *Remote Switch are

in the “ON” position resulting in excessive
resistance.

When turning on the burner using a *remote switch,
ensure that the standard OFF/ON switch is in the OFF
position. If both switches are in the ON position,
it may result in excessive resistance (and millivolt
drainage) and the burner may not come on.

a. Pilot flame may be too low or blowing

(high) causing the pilot/valve safety to

Clean and/or adjust pilot flame for maximum flame
impingement on thermocouple

drop out.

76

Innovative Hearth Products
Superior

TM

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

Table 55: Troubleshooting Electronic Systems

1. Nothing happens

when the fireplace is
turned ON/OFF.

a. Remote is not functioning properly. Check that the wall switch plate is set to REMOTE.

Operate the fireplace from the wall plate switch.
Replace remote and/or wall switch batteries.

b. Gas is not reaching the fireplace. Check the gas supply and gas shutoff valves. *
c. Unit is not receiving power. Check/replace backup batteries behind the wall plate.

Replace unit battery backup.
Check building circuit breakers to ensure power is ON

to the fireplace.

2. The main burner

does not light and the
igniter is sparking.

a. Gas is not reaching the fireplace. Check the gas supply and gas shutoff valves.
b. Loose wires to the valve. Check control compartment for any obviously loose

wiring (call a service technician, if necessary).

c. Loose wires to ignition module. Check control compartment for any obviously loose

wiring (call a service technician, if necessary).

d. Air in the gas line. Purge gas line of air (call a service technician if

required).

e. Unit is not receiving power. Replace unit battery backup.

3. The main Burner

comes on but then
goes out.

a. Gas is not reaching the fireplace. Check the gas supply and gas shutoff valves.
b. Loose wires to the valve or ignition

module.

Check control compartment for any obviously loose
wiring (call a service technician, if necessary).

c. Pilot flame is not engulfing the sensor. Call a service technician.
d. Obstructed vent system. Call a service technician.

4. Soot is present on the

logs and glass.

a. Excessive flame impingement on the logs. Properly position the logs as detailed on Page 58.
b. Initial fireplace operation. A white film may develop on the glass during the first

few fires as part of the burn-in process.
The first few times you use the fireplace, clean

the glass after each use (AFTER THE GLASS HAS
COMPLETELY COOLED); otherwise, the white film will
bake onto the glass and become difficult to remove.

See glass cleaning instructions in the MAINTENANCE
section of this manual.

c. Improper vent restrictor setting. Open the air shutter by adjusting the air shutter

adjustment lever according to the instructions in
this manual.

d. Improper air shutter opening. Open the air shutter by pushing in the rod.

5. Poor flame and/or

blue flame.

*The unit may have multiple gas supply shutoffs (the main gas supply valve in the house, the gas supply valve in the fireplace control compartment, and/or an
additional shutoff valve near the fireplace).

a. Door seal is not properly aligned, causing

gaps and air leaks.

Remove and realign the door so the gasket seal is
fully engaged around the door frame.

Operation

WARNING

Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards.

77

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

REPLACEMENT PARTS

Table 56: Installer Replacement Parts

33” Models 35” Models 40” Models 45” Models

Description

1 Electronic Pilot Assembly, Natural Gas H7268 1 H7268 1 H7268 1 H7268 1
2 Electronic Pilot Assembly, Liquid Propane H7269 1 H7269 1 H7269 1 H7269 1
3 Electronic DFC Wire Harness Assembly H8601 1 H8601 1 H8601 1 H8601 1
4 Electronic DFC Ignition Board H7272 1 H7272 1 H7272 1 H7272 1
5 Electronic Power Transformer H8006 1 H8006 1 H8006 1 H8006 1

Electronic Battery Holder

6

(for backup batteries)
7 Electronic Ground Wire H7278 1 H7278 1 H7278 1 H7278 1
8 Electronic ON/OFF Switch 27K30 1 27K30 1 27K30 1 27K30 1
9 Millivolt Pilot Assembly, Natural Gas 69L17 1 69L17 1 69L17 1 69L17 1

10 Millivolt Pilot Assembly, Liquid Propane 69L18 1 69L18 1 69L18 1 69L18 1
11 Millivolt Piezo Igniter 10K86 1 10K86 1 10K86 1 10K86 1
12 Millivolt Piezo Igniter Wire 56L21 1 56L21 1 56L21 1 56L21 1
13 Millivolt Pilot Generator 60J79 1 60J79 1 60J79 1 60J79 1
14 Millivolt Thermocouple 74L57 1 74L57 1 74L57 1 74L57 1
15 Millivolt Pilot Tube 74L56 1 74L56 1 74L56 1 74L56 1
16 MIllivolt Electrode and Cable H6212 1 H6212 1 H6212 1 H6212 1
17 Orifice Holder H7257 1 H7257 1 H7257 1 H7257 1
18 Gas Flex Line Connector 93L32 1 93L32 1 93L32 1 93L32 1
19 Gas Valve, Electronic, Natural Gas H6209 1 H6209 1 H6209 1 H6209 1
20 Gas Valve, Electronic, Liquid Propane 88J53 1 88J53 1 88J53 1 88J53 1
21 Gas Valve, Millivolt, Natural Gas F1833 1 F1833 1 F1833 1 F1833 1
22 Gas Valve, Millivolt, Liquid Propane F1834 1 F1834 1 F1834 1 F1834 1
23 Logset F1883 1 F1829 1 F1830 1 F1884 1
24 Vent Restrictor Base H8987 1 H8987 1 H8987 1 H8987 1
25 Vent Restrictor Wing H8988 1 H8988 1 H8988 1 H8988 1
26 Door Latch Assembly H6135 1 H6135 2 H6135 2 H6135 2
27 Split Flow Valve H8996 1 H8996 1 H8996 1 H8996 1
28 Hi-Low Switch J7359 1 J7359 1 J7359 1 J7359 1
29 On/Off Switch (Split Flow) J7360 1 J7360 1 J7360 1 J7360 1
30 Wall Switch Harness (Electronic) J7358 1 J7358 1 J7358 1 J7358 1
31 Vent Stopper Plug J7356 1 J7356 1 J7356 1 J7356 1
32 Burner Assembly J7402 1 F1843 1 F1844 1 F1844 1
33 Superior

34 Manning Glass Gasket F2116 1 F2116 1 F2116 1 F2116 1
35 Wall Plate J7401
36 Switch Jumper (Split Flow) J7369 1 J7369 1 J7369 1 J7369 1
37 25” Wall Switch Harness H8931 1 H8931 1 H8931 1 H8931 1
38 Porcelain Panel Right (Contemporary) n/a n/a J7391 1 J7394 1 n/a n/a

39 Porcelain Panel Left (Contemporary) n/a n/a J7392 1 J7395 1 n/a n/a
40 Porcelain Panel Center (Contemporary) n/a n/a J7393 1 J7396 1 n/a n/a
41 Trim Kit (Stainless) n/a n/a F2468 1 F2469 1 n/a n/a
42 Trim Kit (Black) n/a n/a F2470 1 F2471 1 n/a n/a
43 Power Adapter Skytech n/a n/a J7930 1 J7930 1 n/a n/a
44 Battery Holder Skytech n/a n/a J7931 1 J7931 1 n/a n/a

78

TM

Square Grate H7719 1 H7719 1 H7720 1 H7720 1

Catalog

Number

H8803 1 H8803 1 H8803 1 H8803 1

Qty

1 J7401 1 J7401 1 J7401 1

Catalog
Number

Qty

Catalog

Number

Qty

900285-00 05/2015

Catalog
Number

Operation

Qty

Innovative Hearth Products
Superior

TM

DRT/C3000 Series Direct-Vent Gas Fireplaces

900285-00 05/2015

45 Wire harness 15’ Skytech BLD n/a n/a J7932 1 J7932 1 n/a n/a
46 V-wire Skytech n/a n/a J7933 1 J7933 1 n/a n/a
47 Regulator maxitrol n/a n/a J7934 1 J7934 1 n/a n/a

48 Pilot Assembly Skytech n/a n/a J7935 1 J7935 1 n/a n/a
49 Valve Single outlet Copreci n/a n/a J7936 1 J7936 1 n/a n/a
50 Control module Skytech BLD n/a n/a J7937 1 J7937 1 n/a n/a
51 Non-combustible Fireboard (Contemporary) n/a n/a J7436 1 J7440 1 n/a n/a

WARNING

Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards.

Operation

79

Innovative Hearth Products

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Figure 59: Replacement Parts

23

53

Operation

900285-00 05/2015

52

31

34

19

20

21

22

47

55

54

33

48

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically
approved with this appliance may result in property damage or personal injury.

AVERTISSEMENT

Risque de dommages ou de blessures si les pièces ne sont pas installées conformément à ces schémas et
ou si des pièces autres que celles spécifiquement approuvées avec cet appareil sont utilisées.

Table 57: Homeowner Replacement Parts

33” Models 35” Models 40” Models 45” Models

Description

52 Hood F1900 1 F1837 1 F1838 1 F1901 1
53 Barrier F1902 1 F1839 1 F1840 1 F1903 1
54 Glass Door F1905 1 F1841 1 F1842 1 F1906 1
55 Control Compartment Door F1898 1 F1835 1 F1836 1 F1899 1
56 Touch-Up Paint F1881 1 F1881 1 F1881 1 F1881 1
57 Glowing Embers 88L53 1 88L53 1 88L53 1 88L53 1
58 Volcanic Stone 80L42 1 80L42 1 80L42 1 80L42 1

Tumbled River Stone

59

(Contemporary)
Driftwood Log Set – Gulf

60

80

Shores (Contemporary)

Catalog
Number

n/a n/a H7536 1 H7536 1 n/a n/a

n/a n/a H2487 1 H2487 1 n/a n/a

Catalog
Number

Catalog

Number

Qty

Catalog
Number

Qty

Catalog
Number

Qty

Innovative Hearth Products

12/02/2013

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

WARRANTY

THE WARRANTY

Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior™ Brand gas fireplace, Stove or Insert ("Product") to be free from defects in materials
and workmanship at the time of manufacture. The Product body and firebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against
thermal breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited
Warranty period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or replacement
is not commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also pay IHP prevail­ing labor rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to five years. THERE ARE EXCLUSIONS AND LIMITATIONS
to this 20 Year Limited Warranty as described herein.

COVERAGE COMMENCEMENT DATE

Warranty coverage begins on the date of installation. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six
months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following
the date of product shipment from IHP, regardless of the installation or occupancy date.

EXCLUSIONS AND LIMITATIONS

This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed
instructions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.

This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be
provided. The Product body and firebox carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components and paint are excluded from
this 20 Year Limited Warranty. The following do not carry the 20 Year Limited Warranty but are warranted as follows:

Burner – Repair or replacement for one year from the date of installation
Gas components – Repair or replacement for one year from the date of installation
Gaskets – Repair or replacement for one year from the date of installation
Logs – Replacement for one year from the date of installation against thermal breakage only
Optional blowers & remote controls – Repair or replacement for one year from the date of installation
Optional glass doors – Repair or replacement for 90 days from the date of installation

Tempered glass - Replacement for one year from the date of installation

Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component

Parts not otherwise listed carry a 90 day warranty from the date of installation.

Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.

IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, fire, flood or acts of God; (b) damages caused by abuse, negligence, misuse, or
unauthorized alteration or repair of the Product affecting its stability or performance (The Product must be subjected to normal use. The Product is designed to burn either
natural or propane gas only. Burning conventional fuels such as wood, coal or any other solid fuel will cause damage to the Product, will produce excessive temperatures
and could result in a fire hazard.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with the Product;
(d) damages, repairs or inefficiency resulting from faulty installation or application of the Product.

IHP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction condi­tions which may generate negative pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for drafting conditions caused by
venting configurations, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions that affect the operation of the unit.

This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction, which are not
manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due to
any malfunction or defect in equipment are not covered by this warranty. All replacement or repair components will be shipped F.O.B. from the nearest stocking IHP factory.

LIMITATION ON LIABILITY

It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied,
or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified herein.

In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or
after repair or replacement, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of fitness for a
particular use or purpose, and there is no implied condition of fitness for a particular use or purpose.

IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.

No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year
Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.

INVESTIGATION OF CLAIMS AGAINST WARRANTY

IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.

To receive the benefits and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.

Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a

contractor that is not approved without first obtaining IHP's prior written consent.

HOW TO REGISTER A CLAIM AGAINST WARRANTY

In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/
distributor, then you must notify IHP in writing. IHP must be notified of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the
IHP Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our website at WWW.SUPERIORFIREPLACES.US.COM.

Operation

900285-00 05/2015

Innovative Hearth Products

Superior™ Brand Gas Fireplaces, Stoves and Inserts

20 Year Limited Warranty

Printed in U.S.A. © 2013 Innovative Hearth Products LLC

P/N 900223-00, Rev. NC 12/2013

Innovative Hearth Products

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

81

Innovative Hearth Products

P900285-00

TM

Superior

DRT/C3000 Series Direct-Vent Gas Fireplaces

Installation and Operation Instructions

Contact an IHP dealer to obtain any of these parts. Please contact IHP for the phone number of your nearest IHP dealer.

SuperiorFireplaces.us.com

Record the following important information about your fireplace:

900285-00 05/2015

Fireplace model number

Fireplace serial number

Date fireplace was Installed

Type of gas fireplace uses

Dealer name

Innovative Hearth Products reserves the right to make changes at any time, without notice, in

IHP.us.com

design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.

Printed in U.S.A. © 2015 Innovative Hearth Products LLC
P/N 900285-00 Rev. E 05/2015 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210