Supera MGD15-1 Instruction Manual

Page 1
MGD10-1, MGD15-1
MEAT GRINDERS
INSTRUCTION MANUAL
This manual contains importatant information regarding your Supera unit. Please read this manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular maintenance guidelines outlined in this manual may void the warranty.
Page 2
WARNINGS
• Do not immerse unit, cord or plug in liquid at any time
• Do not grind hard foods
• Unplug cord from outlet when not in use and before cleaning
• Plug only into a 3-hole grounded electrical outlet
• Do not operate unattended
• Do not use this unit for anything other than intended use
• Do not use outdoors
• Always use on a fi rm, dry and level surface at least 12” from walls or any other obstruction
• Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or has been damaged in any manner
• Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to property loss and injury. All repairs should be done by authorized professionals only.
• Ensure that the designated power supply is adequate for continual usage and the voltage is correct
• Only use food pusher to feed grinder. Do not feed by hand.
TO USE Assembling:
1. Place Head tightly onto opening of Motor Housing.
2. Holding Head with one hand tighten Locking Knob clockwise.
3. Place Feed Screw into Head, long end fi rst, by turning Feed Screw slightly until it is set into Motor Housing and cover the transmission shaft.
4. Place Cutting Blade onto Feed Screw shaft with the blade facing the front.
5. If it is not fi tting properly, the meat will not be ground
6. Place desired Cutting Plate next to Cutting Blade, gap align the pin of head.
7. Screw Cap into place until tight – do not over tighten
8. Place Hopper Plate on Head and fi x into position then set unit on a fi rm surface.
Mincing Meat:
1. Ensure the switch is o before plugging in.
2. Plug the power cord into the appropriately rated outlet.
3. Before use, wash all parts excluding those that do not touch food, in warm soapy water.
4. Cut all food into pieces so that they fi t easily into plate opening.
5. Switch the unit on.
6. Feed food product into plate using food pusher.
CLEANING – NOTE: To maintain cleanliness and increase service life, the meat grinder should be cleaned daily. Do not immerse the unit in water or any other liquid. If liquid enters the electrical compartment it may cause a short circuit or electrical shock. Disassembling:
1. Before cleaning or attempting to move make sure the switch is o and the motor has stopped completely and then disconnect the plug from power outlet.
2. Screw cap has 3 fl at sides, convenient for unscrewing. If screw cap is too tight, knock at the fl at sides with a soft handle. Cap should unscrew easily.
3. Unscrew the locking knob and take out head (with cutting plate, cutting blade and feed screw) then put head mouth downward in order to take out cutting plate, cutting blade and feed screw.
Cleaning:
1. Remove meat product.
2. Wash each part with warm soapy water. After washing and drying, lubricate the feed screw, cut­ting blade and cutting plates.
3. Do not immerse motor housing in water. Wipe with a damp cloth.
4. To avoid damage, do not use abrasive cleaners or scouring pads.
5. If soap or chemical cleaners are used, be sure they are completely rinsed away with clear water immediately after cleaning. Chemical residue could damage or corrode the surfaces of the unit.
INSTRUCTION
©SUPERA V.1.0 | August 2014
Page 3
JAMMING
When the circuit breaker automatically stops the motor, or when the motor continues to function but no meat comes out of cutting plate, bone or other materials may be jamming the unit. Perform the following steps:
1. Switch unit o .
2. Press circuit breaker to reset.
3. Turn switch to reverse to clear jamming of bone or other materials.
4. Reverse operation will continue for as long as reverse is held down.
TROUBLESHOOTING
If the minced meat is not discharged smoothly or appears to be in the form of paste, see the following:
PROBLEM: Screw cap is tightened too much thus cutting blade does not contact properly with the cutting plate
SOLUTION: Re-adjust it
PROBLEM: The cutting plate is blocked SOLUTION: Clean it
PROBLEM: Cutting blade is dull SOLUTION: Grind or replace it
INSTRUCTION
©SUPERA V.1.0 | August 2014
Page 4
Parts Diagram and Replacement Parts for the Meat Grinders
2
3
4
6
5
9
7
Reference
1
8
MGD10-1
INSTRUCTION
Number Part Number Description
1MG1-1Switch 2 MG1-2 Hopper Plate 3MG1-3Locking Knob 4MG1-4Head 5 MG1-5 Feed Screw 6 MG1-6 Grinder Knife 7 MG1-7 Grinder plate - #12 Coarse 8 MG1-8 Grinder plate - #12 Medium 9MG1-9Screw Cap
©SUPERA V.1.0 | August 2014
Page 5
Parts Diagram and Replacement Parts for the Meat Grinders
11
4
3
10
9
8
Reference
7
6
MGD15-1
5
Number Part Number Description
1 MG15-1 Switch 2 MG15-2 Locking Knob 3 MG15-3 Hopper Bracket
2
1
INSTRUCTION
4 MG15-4 Hopper Plate 5 MG15-5 Head 6 MG15-6 Feed Screw 7 MG15-7 Cutting Knife 8 MG15-8 Grinder Plate (Coarse)
9 MG15-9 Grinder Plate (Medium) 10 MG15-10 Screw Cap 11 MG15-11 Food Pusher
©SUPERA V.1.0 | August 2014
Page 6
www.SuperaCo.com
LIMITED WARRANT Y
SUPERA COUNTERTOP COOKING EQ UIPM ENT MODELS:
Meat Grinders: [MGD10-1, MGD15-1]
Claims: All claims for parts or labor must be made directly through SUPERA, LLC. All claims should include: model number of the unit,
the serial number of the unit, proof of purchase, date of installation, and all pertinent information supporting the alleged defect. Failure to comply with warranty policies will result in voiding claims. Any service provided without authorization from Supera, LLC will not be covered by Supera, LLC.
One-Year Parts & Labor Warranty: SUPERA, LLC warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subjected to normal use, is free from defects in material or workmanship for one year. Warranty includes onsite service calls within 60 miles of an author ized ser v ice compa ny . End user is responsible for all extra travel and mileage at prevailing rates and for original call to Supera expressing need for warranty service. Any service provided without authorization from Supera, LLC will not be covered by Supera, LLC.
EXCLUSIONS: Example of items not covered under warranty, but not limited to only these items:
1) Acts of God, fire, water damage, burglary, accident, theft
2) Freight damage
3) Improper installation or alteration of equipment
4) Use of generic or after market parts.
5) Repairs made by anyone other than a SUPERA designated servicer
6) Lubrication
7) Expendable wear parts, adjustable feet, blown fuses, lamps, etc
8) Cleaning of equipment
9) Misuse or abuse
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. SUPERA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. SUPERA, LLC HAS FINAL DESCRETION ON ALL WARRANTY REQUESTS.
SUPERA’S OBLIGATIONS: SUPERA’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.
All repairs pursuant to this Warranty will be performed by an Authorized Designated SUPERA Service Location during normal working hours. This warranty does not cover services performed at overtime or premium labor rates. End user is responsible for the difference between normal service rates and premium service rates. This warranty does not cover any service technician errors. IN NO EVENT SHALL SUPERA BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING, WITHOUT L IMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR OTHERWISE.
This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees. Inst allatio n in a residential application will void all warranties.
Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear, improper set up and use. Periodic maintenance is not covered. Warranty does not cover service requests for free replacement and/or recall parts.
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. SUPERA NEI THER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.
Not Covered Under This Warranty: SUPER A, LLCʼs sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty. Warranty does not cover service requests for free replacement and/or recall parts.
SUPERA, LLC HAS FINAL DESCRETION ON ALL WARRANTY REQUESTS. NO CONSEQUENTIAL DAMAGES. SUPERA, LLC IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOSSES, SERVICE TECHNICAN ERRORS, OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE REGARDLESS OF W HETHER OR NOT THEY RESULT FROM REFRIGERAT ION FAILURE. W ARRANTY IS NOT TRANSFERA BLE, This warranty is not assignabl e and applies only in favor of th e original purchaser/user to whom delivered. ANY SUCH ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANNTIES HEREIN AND SHALL VOID ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER THE WARRANTY PACKET PROVIDED WITH THE UNIT. ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANS IT OR INSTALLATION, FIRE, FOOD , A CTS OF G OD. S UPER A, LLC is n ot respo nsibl e for the repair
© Supera 2014 Version 5 | May 2014
Page 7
www.SuperaCo.com
or replacement of any parts that SUPERA, LLC determines hav e b ee n s u bjected after the da te of manufacture to alteration, n egle ct , ab use, misuse, accident, damage duri ng transit or installati on, fire, flood, or act of GOD. IMPROPER ELECTRICAL CONNECTIONS. SUPERA, LLC IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS RESULTING FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS, LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT. NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE; THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, EXCEPT THE TWO (2) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL THREE (3) YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE. THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DE SCRIPTION ON THE FACE HEREOF. Outside U.S. an d Canad a; thi s warra nty does not appl y, and SUP ERA, LLC is not responsi ble fo r, an y warr ant y claims m ade on p roduc ts sold or us ed outsi de t he continent of the United States and Canada. Installation in a residential application will void all warranties.
FOR WARRANTY AND NON-WARRANTY related issues, technic
al support, purchase replacement parts and warranty registration call 866-953-3288 for technical support. Please have your model number, serial number and proof of purchase ready.
© Supera 2014 Version 5 | May 2014
Loading...