SunX EQ-501, EQ-502T, EQ-502, EQ-501T, EQ-511 User guide

...

Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference.

INSTRUCTION MANUAL

Photoelectric Sensor

Adjustable Range Reflective

EQ-500 Series

SPECIFICATIONS

Type

Item With timer Adjustable range (Note 1) (Note 2) Sensing range (Setting dis-

tance maximum) (Note 2)

Hysteresis (Note 2)

Power / Current consumption

Output

Response time Operation indicator Stability indicator Distance adjuster Sensing mode Timer function Automatic interference

prevention function Protection Ambient temperature Ambient humidity Emitting element Receiving element Material Connection method Cable Cable length Weight Accessory

Notes: 1)

Model No.

Output operation Short-circuit protection

The adjustable range stands for the maximum sensing range which can be set with the adjuster.

The adjustable range, the sensing range and the hysteresis are specified for white non-glossy paper (200200mm) as the object.

When the sensors are mounted closely, use them in the interference prevented area, as shown below.

Lmm

Setting range (m)

or more

06020 8040

Note that the detection may be unstable depending on the mounting conditions or the sensing object. In the state where this product is mounted, be sure to check the operation with the actual sensing object to be used.

Mounting interval L (mm)

INFORMATION RELATING TO

EQ-501

EQ-501T

0.2 to 2.5m 0.2 to 1.0m

24 to 240V AC r 10% or 12 to 240V DC r 10% Ripple P-P 10% or less

AC: 4VA or less (With timer: 5VA or less) DC: 3W or less (With timer: 4W or less)

Relay contact 1a

࡮Switching capacity: 250V AC 3A (resistive load)

࡮Electrical life: 100,000 or more operations

࡮Mechanical life: 50,000,000 or more operations

20ms or less (Depends on the timer setting period for EQ-50غT)

Interference prevented

LOW VOLTAGE DIRECTIVE (Multi-voltage type only)

Item

Impulse withstanding voltage

Rated conditional protective device

Note: Each condition for use that the standards require is under

less than 2,000m above sea level.

CAUTIONS

This product has been developed / produced for industrial use only. Make sure that the power supply is off while wiring and adjusting.

Take care that wrong wiring will damage the sensor.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching reg-

ulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.

FUSE 5A FAST BLOWShort-circuit protective device

Multi-voltage

Short sensing range

EQ-502

EQ-502T

10% or less of operation distance

30V DC 3A (resistive load)

(switching frequency 1,200 times/hour)

(switching frequency 18,000 times/hour)

Switchable either Detection-ON or Detection-OFF

㧙

Orange LED (lights up when the output is ON)

Green LED (lights up under stable operating condition)

2-turn mechanical adjuster with pointer

㧙

EQ-5غT: Selectable from ON-delay and OFF-delay (0.1 to 5 sec. variable)

-25to+55 (No dew condensation or icing allowed), Storage: -30 to +70

Enclosure: ABS, Front cover: Polycarbonate, Display cover: Polycarbonate

Extension up to total 100m is possible with 0.3mm

100g approx. 85g approx.

Description

IEC 60947-5-2: 1998Refering standard

AC-12/DC-12Utilaization category

2.5kV 3Pollution degree

25HzFrequency of operation cycle 20msTurn off time

12%Excess gain

100A

35 to 85% RH, Storage: 35 to 85% RH

Infrared LED (modulated)

2-segment photodiode

Screw-on terminal connection

Suitable for round cable Ǿ9toǾ11mm

Adjusting screwdriver: 1 pc.

Lmm or more

٨٨Never use this product as a sensing

device for personnel protection. In case of using sensing devices for personnel pro-

WARNING

Incorporated (Note 3)

tection, use products which meet laws and standards,suchasOSHA,ANSIorIECetc.,forpersonnel protection applicable in each region or country.

DC-voltage

EQ-511

EQ-511T

0.2 to 2.5m 0.2 to 1.0m

0.1 to 2.5m 0.1 to 1.0m0.1 to 2.5m 0.1 to 1.0m

12 to 24V DCr10%˴Ripple P-P 10% or lessSupply voltage

NPN open-collector transistor ࡮Maximum sink current: 100mA

Applied voltage: 30V DC or less (between output and 0V)

࡮ ࡮

Residual voltage: 1V or less (at 100mA sink current)

PNP open-collector transistor ࡮Maximum source current: 100mA

Applied voltage: 30V DC or less (between output and +V)

࡮ ࡮

Residual voltage: 1V or less (at 100mA source current)

2ms or less (Depends on the timer setting period for EQ-51غT)

IP67 (IEC)

Lmm or more

0.4V or less (at 16mA source current)

Switch either BGS or FGS function

, or more, cabtyre cable

Lmm or more

Short sensing range

45mAorless

0.4V or less (at 16mA sink current)

Incorporated

Setting range (m)

Mounting interval L (mm)

Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction.

In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground. Take care that the sensor is not directly exposed to fluores-

cent light from a rapid-starter lamp, a high frequency lighting device or sunlight etc. as it may affect the sensing performance. If an external surge voltage exceeding 4kV (DC-voltage:

1kV) is impressed, the internal circuit will be damaged, and a surge suppressing element should be used. Do not use during the initial transient time (50ms) after

the power supply is switched on.

This sensor is suitable for indoor use only. A mechanical structure is employed for the distance ad-

juster of this product. Take care not to drop the product. Do not use this sensor in places having excessive va-

por, dust, etc., or where it may come in direct contact with water, or corrosive gas.

Take care that the sensor does not come in contact with water, oil, grease, organic solvents, such as, thinner, etc., strong acid or alkaline.

This sensor cannot be used in an environment containing inflammable or explosive gases.

Never disassemble or modify the sensor.

EQ-512

EQ-512T

Interference prevented area

150 20050250100

MOUNTING

٨ The tightening torque should be 0.8N㨯morless.

M5 PWV

M5 (length 32mm) screw with washers

Sensor mounting bracket

MS-EQ5-01

(Optional)

Care must be taken regarding the sensor mounting direction with respect to the object's direction of movement.

Good

Sensing object

Good

Sensing object

Not good

Sensing object

Do not make the sensor detect an object in this direction because it may cause unstable operation.

٨٨When detecting a specular object (aluminum or copper

foil, etc.) or an object having a glossy surface or coating, please take care that there are cases when the object may not be detected due to a small change in angle, wrinkles on the object surface, etc. When a specular body is present below the sensor, use the sensor by tiling it slightly upwards to avoid wrong operation.

Not good

Specular face

If a specular body is present in the background, wrong

Specular face

Good

Tilt

operation may be caused due to a small change in the angle of the background body. In that case, install the sensor at an inclination and confirm the operation with the actual sensing object. This product is not easily affected by the reflected light inten-

sity since this sensor is the adjustable range reflective type. When the reflected light intensity is remarkably low, the sensing range may be affected. In that case, mount the sensor, while checking light-up of the stable indicator (green). Mounting screws of the terminal cover and display

cover should certainly be tightened to maintain the water tight rating, however, the tightening torque of the screws should be of 0.3 to 0.5N㨯m.

WIRING CONNECTIONS

٨٨Check all wiring before applying power since incorrect

wiring may damage the internal circuit. Also, carefully tighten the terminal screws so that the wires of adjacent terminals do not touch. The mounting hole for screw the terminal cover fixing inclines 70 degrees to the terminal cover, as shown in the figure below. To avoid damaging this product or a screw, take care when tightening or loosening a screw.

Screw for terminal cover fixing

70q

Screwdriver

٨࡮To maintain a watertight performance, the cable should

have an outer diameter between Ǿ9toǾ11mm with a smooth covering material that allows the accessory conduit connector to be securely tightened, however, the tightening torque of the screw should be of 1.5 to 2.0N㨯m.

Composition of a conduit connector, and processing of a cable

Conduit connector

Gland packing (Note)

37mm

Power

Output

25mm

When assembling the conduit connector, take care of the

Note:

direction of the gland packing. Furthermore, in order to maintain a watertight performance, fit the gland packing such that the seating surface of the gland packing contacts the packing holder part of the terminal cover evenly.

Gland

٨࡮If pressure terminals are to be used, affix the connect-

ed pressure terminals to a terminal (M3.5 screw).

Dimensions of the suitable crimp terminals

(Unit: mm)

Round type Y-shaped type

Ǿ3.6 or more

7.5 or less

22 or less

10 or less

17 or less

(After crimping)

7 or less

Ǿ3.6 or more

7.5 or less

22 or less

10 or less

17 or less

(After crimping)

7 or less

࡮ The tightening torque of the terminal screws should be

0.3to0.5N㨯m.

I/O CIRCUIT DIAGRAMS

٨ Multi-voltage type

Multi-voltage circuit

Output relay

Sensor circuit

Internal circuit

٨ DC-voltage type

Tr2

Sensor circuit

Tr1

Internal circuit Users' circuit

Symbols...

D: Reverse supply polarity protection diode

D1,ZD2: Surge absorption zener diode

r1: NPN output transistor

r2: PNP output transistor

ZD2

ZD1

Terminal No.

Power supply 24 to 240V ACr10%

12 to 240V DCr10%

Relay contact (1a)

Terminal No.

100mA max.

Output (PNP) Output (NPN)

Load

100mA max.

12 to 24V DC

r10%

٨ Terminal position

Ԙ Ԛ

PART DESCRIPTION

Stability indicator (Green) Distance adjuster

(2-turn)

Adjuster indicator

Operation indicator (Orange)

Notes: 1)2)The operation mode switch of the DC-voltage type is the

DIP switch. Refer to ' OPERATION MODE SWITCH'for details. Incorporated on EQ-5غT only.

OPERATION MODE SWITCH

ԙ ԛ

OFF-delay timer switch (Note 2)

ON-delay timer switch (Note 2)

Operation mode switch (Note 1)

٨ Multi-voltage type (L-ON / D-ON mode only)

Operation mode switch

Detection-ON mode is obtained when the switch is turned fully clockwise.

Detection-OFF mode is obtained when the switch is turned fully counterclockwise.

Note: Turn the operation mode switch gradually and lightly with the

attached screwdriver. If the distance adjuster is over turned or pressed heavily, it may be damaged.

Description

٨ DC-voltage type

L-ON / D-ON mode BGS / FGS mode Timer mode Not used

LD BGS FGS OFF

Timer ON N.C.N.C.

BGS / FGS FUNCTION (DC-voltage type only)

٨٨This sensor incorporates BGS / FGS function. Select

either BGS or FGS function depending on the positions of the background and sensing object. BGS / FGS function is set with the operation mode switch. Depends on a selection of either BGS or FGS function, the output operation changes as follows.

Sensing range

Non-detectable area

L-ON

BGS

D-ON

L-ON

FGS

D-ON

This function is used when the sensing object is apart from the background.

٨ This function is used when the sens-

ing object contacts the background or the sensing object is glossy, etc.

DISTANCE ADJUSTMENT

For DC-voltage type, be sure to set the BGS / FGS function before distance adjustment. If the setting is done after the distance adjustment, the sensing area is changed.

٨٨Turn the distance adjuster gradually and lightly with

the attached screwdriver. If the distance adjuster is over turned or pressed heavily, it may be damaged.

Multi-voltage type, DC-voltage type࡮BGS select

Step

Turn the distance adjuster fully counterclockwise to the minimum sensing range position.

(0.2m approx.)

Please an object at the required distance from the sensor, turn the distance adjuster gradually clockwise, and find out point

where the sensor changes to the light received condition.

Remove the object, turn the distance adjuster further clockwise, and find out point where the sensor changes to the light received condition again with only the background.

When the sensor does not go to the light received condition even if the adjuster is fully turned clockwise, point is this extreme point.

The optimum position to stably detect objects

is the center point between and .

When a sensing object is approaching / moving away from the sensor.

Follow only steps Ԙ and ԙ. Since the sensing point

may change depending on the sensing object, be sure to check the operation with the actual sensing object.

٨ DC-voltage type࡮FGS select

Step

Turn the distance adjuster fully clockwise to the maximum sensing range position. (2.5m

approx., 1.0m approx. for EQ-512غ

In the state where the sensor detects the background, turn the distance adjuster gradually counterclockwise, and find out point

where the sensor changes to the undetecting condition.

Place an object at the required distance from the sensor, turn the adjuster counterclockwise further until the sensor goes into the undetecting condition again. Once it has entered, turn the adjuster backward a little until the sensor returns to the

detecting condition. That position is designated as point .

When the sensor does not go into the undetecting condition even if the adjuster is fully turned counterclockwise, the position where the adjuster was fully turned is regarded as the point .

The optimum position to stably detect objects

is the center point between and .

Adjusted distance

Description

ON OFF

Sensing object

Background

Distance adjuster

Turn fully

Distance adjuster

Turn fully

Optimum position

Optimum

position

STABILITY INDICATOR

٨ Since the EQ-500 series use a 2-segment photo-

diode as its receiving element, and sensing is done based on the difference in the incident beam angle of the reflected beam from the sensing object, the output and the operation indicator (orange) operate according to the object distance. Further, the stability indicator (green) shows the margin to the setting distance.

Setting distance

Sensing object

Output (operation indicator) (In case of Detection-ON)

Stability indicator

Background

Stable operating condition

TIMER FUNCTION (EQ-5غTonly)

An OFF-delay timer, which is useful when the re-

Stable operating condition

Unstable operating condition

sponse of the connected device is slow, etc., an ON-delay timer, which is useful when the input specifications of the connected device require a signal of a fixed width, are possible with EQ-5غT.

The OFF-delay timer and the ON-delay timer can be used at the same time.

For DC-voltage type, set the DIP switch for the timer selecting to 'Timer ON' side.

Sensing condition

Operation

Light-received normal operation

Light-received ON-delay

Light-received OFF-delay

Light-received ON/OFF-delay

Light-interrupted normal operation

Light-interrupted ON-delay

Light-interrupted OFF-delay

Light-interrupted ON/OFF-delay

Note: Turn the timer switch gradually and lightly with the attach-

ed screwdriver. If the distance adjuster is over turned or pressed heavily, it may be damaged.

INTENDED PRODUCTS FOR

TT T

Timer period: T = 0.1 to 5s (variable)

CE MARKING

The models listed under ' SPECIFI-

CATIONS' come with CE Marking. As for all other models, please contact our office.

SUNX Limited

Overseas Sales Dept. (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA Phone: +1-908-464-3550

PRINTED IN JAPAN

ON (lights up)

OFF (lights off)

Lights up

Lights off

Beamreceived Beaminterrupted

OFF ON

OFF

OFF ON

OFF

URL : sunx.jp