SUNRISE MEDICAL F16
Owner’s Manual
51 SUNRISE F16 Issue 8
SUNRISE F16
How to use this manual
We at Sunrise Medical want you to get the best out of your F16 wheelchair.
This Owner’s Manual will familiarise you with the chair and its features. It
contains hints on everyday usage and general care in addition to
information on the high quality standards which we adhere to and details
about the guarantee. There are a wide range of components and
adjustments available on the F16 for further information about these you
should contact your wheelchair prescriber/supplier.
Your wheelchair will reach you in excellent condition having been personally
inspected before leaving our factory. By following the guidelines for
maintenance and cleaning on page 38 your wheelchair will maintain its first
class condition and give you complete satisfaction.
SUNRISE F16 Issue 6
SUNRISE F16 Issue 8 50
Contents
Introduction page 1
Guarantee page 2
Features and options page 3
Safety tips page 4 - 6
Preparing your wheelchair for use page 7 - 12
Pilot control page 13 - 15
The Penny and Giles Pilot + control pod page 16 - 23
Parallel Swing-Away page 24
Batteries and charging page 25 - 33
User tips page 34 - 36
Transporting your chair page 37 - 38
Lap belt instructions page 39 - 41
Maintenance page 42 - 43
Service history page 44
Sunrise Medical page 45
1 SUNRISE F16 Issue 8
Introduction
The F16 has been designed for use by an individual on a daily basis. It is
suitable for both indoor and outdoor use. It is only intended for use as a
pavement vehicle, but may also be used when crossing between
pavements.
This vehicle has been designed for a single occupant of limited mobility up
to the weight of 118Kg, who has the cognitive, physical and visual ability to
control the vehicle safely. If you are in any doubt as to the suitability of the
powerchair, contact your local Sunrise approved dealer for clarification,
prior to commencing use.
It is very important to read the relevant section of the Owner's Manual when
making any adjustments. If you have any queries about the use,
maintenance or safety of your wheelchair, please contact your local
approved Sunrise Medical service agent. If you do not know of an approved
dealer in your area, or have any other questions please write or telephone:
SUNRISE MEDICAL LIMITED
HIGH STREET WOLLASTON
WEST MIDLANDS DY8 4PS
ENGLAND
Telephone 01384 44 66 88 Fax. 01384 44 66 99
International Telephone +44 1384 44 66 88 Fax.+44 1384 44 66 99
www.sunrisemedical.co.uk
Sunrise Medical is ISO 9001 certified, which ensures quality at all stages of
the development, and production of this wheelchair.
This product is manufactured to comply with the radio
interference requirements of EEC directive 89/336/EEC
Medical Device Directive 93/42/EEC
Sunrise is dedicated to providing products of exacting quality which conform
fully and reliably to the requirements of their intended use. Sunrise is
accredited to B.S. EN ISO 9001, which is the internationally recognised
standard for quality management systems. This approval ensures we
provide quality in all areas of our business, from development through to
final delivery.
SERIAL Number: INSPECTED BY:
SUNRISE F16 Issue 8 2
Guarantee
Please remember to fill in and post the guarantee registration card enclosed with this manual. Sunrise
Medical Limited recommend that you do not undertake maintenance tasks other than those explained in this
manual. Your local approved Sunrise Medical service agent is fully trained by Sunrise Medical to carry out
detailed maintenance as and when required. Use only genuine Sunrise Medical replacement parts.
7. The above warranty conditions apply to all
wheelchair parts, for models purchased at full retail
price.
8. Under normal circumstances, no responsibility will
be accepted where the wheelchair has required
repair or replacement as a direct result of:-
a The wheelchair or part not having been
maintained in accordance with the
manufacturer’s recommendations, where such
exist. Or failing to use only the specified original
equipment parts.
b The wheelchair or part having been damaged by
neglect, accident or improper use.
c The wheelchair or part having been altered from
the manufacturer’s specifications, or repairs
having been attempted prior to the service agent
being notified.
Please keep a note of your local service agent’s
address and telephone number in the space below. In
the event of a breakdown, contact them and try to give
all relevant details so they can help you quickly.
The wheelchairs shown and described in this manual
may not be exactly the same in every detail as your
own model. However, all instructions are still entirely
relevant, irrespective of detail differences.
The manufacturer reserves the right to alter without
notice any weights, measurements, or other technical
data shown in this manual. All figures, measurements,
and capacities shown in this manual are approximate,
and do not constitute specifications.
Your local dealer
Your local dealer
Your guarantee
The guarantee form is included in the Sunrise Pack,
please fill in the relevant details and return to us to
register your entitlement.
THIS IN NO WAY AFFECTS YOUR STATUTORY
RIGHTS.
Warranty conditions
1. The repair or replacement will be carried out by an
authorised Sunrise Medical dealer/service agent.
2. To apply the warranty conditions, should your
wheelchair require attention under these
arrangements, notify the designated Sunrise
Medical service agent immediately giving full
information about the nature of the difficulty.
Should you be operating the wheelchair away from
the locality of the designated Sunrise Medical
service agent work under the “Warranty Conditions”
will be carried out by any other service agent
designated by the manufacturer.
3. Should any part of the wheelchair require repair or
replacement, as a result of a specific manufacturing
or material defect, within twelve months from the
date on which the possession of the wheelchair
was transferred to the original purchaser, and
subject to it remaining within that ownership, the
part or parts will be repaired or replaced completely
free of charge if returned to the authorised service
agent.
Note: This guarantee is not transferable.
4. Any repaired or replaced part will benefit from these
arrangements for the balance of the warranty
period applicable to the wheelchair.
5. Parts replaced after the original warranty has
expired are covered for a further twelve months.
6. Items of a consumable nature will not generally be
covered during the normal warranty period, unless
such items have clearly suffered undue wear as a
direct result of an original manufacturing defect.
These items include amongst others upholstery,
tyres, inner tubes, and similar parts.
Sunrise Medical Limited
High Street Wollaston West Midlands DY8 4PS
England
Tel 01384 4466 88 Fax 01384 44 66 99
www.sunrisemedical.co.uk
3 SUNRISE F16 Issue 8
Footrests
page 10-11
Batteries / Charging
page 25-33
Tyres
page 38
Control box
page 13-24
Emergency Freewheel
page 12
Armrests
page 9-11
Seat Cushion
Page 12
Features and options
The F16 has been designed for use by an individual, on a daily basis. It is suitable for
both indoor and outdoor use. It is only intended for use as a pavement vehicle,
but may also be used when crossing between pavements.
This vehicle has been designed for a single occupant, of limited mobility, up to the
weight of 118Kg, who has the cognitive, physical and visual ability to control the
vehicle safely. If you are in any doubt as to the suitability of the powerchair, contact
your local Sunrise approved dealer for clarification, prior to commencing use.
Some of the options shown in this manual may not be available in your country.
For further information please consult your Sunrise supplier.
SUNRISE F16 Issue 8 4
Safety warning and user tips
Safety warnings
Safety is a very important with any
vehicle that is power driven, here
are some helpful tips to safeguard
your use.
General
Always ensure that your
wheelchair is switched off before
attempting to mount or dismount.
Always ensure that you are able to
operate all controls from a
comfortable position. Paying
attention to your posture is
essential to ensure your continued
comfort and well being.
Always make sure that you can be
seen clearly, especially if you
intend using your wheelchair in
poor light.
Kerbs
Never descend a kerb forwards.
Please read carefully the section on
kerb climbing in this manual before
attempting to mount and dismount
any kerbs in your wheelchair.
Do not attempt to climb or dismount
a series of steps. It is unsafe to do
so and could cause personal injury
or damage the chair. The F16 has
only been designed to climb a
single step or kerb.
Routine service
Like most things in life a little care
and attention goes a long way and
your chair is no exception. The
recommended service interval is
one year. (See service history on
later page).
Emergency freewheel
Please remember that you have
no braking facility when the
freewheel lever is moved from
the normal drive position to the
freewheel position.
The wheelchair must never be
left with the lever in the
freewheel position. For a fuller
description of this facility and
its limitations to use please see
later section.
Emergency braking
The simplest and safest way to
stop the wheelchair is to
release the joystick control
lever (see Control pod section).
This will bring the chair to halt
in a controlled manner.
Switching the control system
off whilst the chair is in motion
will also bring the chair to a
halt. This latter method is not
recommended as the stopping
action is very abrupt.
Sharp turns
Full speed turns should not be
attempted. If you need to turn
sharply you must reduce your
speed with the joystick or speed
setting. This is particularly
important when travelling across or
down a slope. Disregarding this
advice could lead to your wheelchair
tipping over.
5 SUNRISE F16 Issue 8
Safety warning and user tips
Batteries
Your wheelchair is supplied as
standard from Sunrise Medical with
maintenance-free batteries. These
only require regular charging.
Do not, under any circumstances,
tamper with the batteries. If in any
doubt contact your local service
agent.
Do not connect the battery charger
to the mains supply until after you
have connected the charger to the
wheelchair. Before charging, please
read the relevant section in this
manual. Take care with battery acid
which is very dangerous. It can
cause burns to the skin as well as
damage to floors, furniture and your
wheelchair. If it comes into contact
with the skin or clothing, wash
immediately with soap and water. If
it comes into contact with the eye,
immediately flood the eye with
running cold water for at least 10
minutes and seek medical attention
immediately. Acid can be
neutralised with baking soda and
water. Take care to keep batteries
upright at all times, especially when
transporting your wheelchair.
Note: Before using your vehicle
for the very first time, please
charge your batteries for a
period of 24 hours.
Tyres
Your wheelchair tyres can wear
depending on use. Check them
regularly in accordance with the
service instructions in this manual,
especially the pressure of the tyres.
NEVER inflate the tyres using a
garage forecourt airline, always
use the pump provided.
Cleaning seating
This is important should the
wheelchair be used by more than
one person to ensure there is no
cross infection.
Cleaning controls
Should the control of your
wheelchair become soiled or dirty, it
can be wiped with a damp cloth
with a dilute disinfectant until clean.
This is important should the
wheelchair be used by more than
one person to ensure there is no
cross infection.
Wheelchair motors
After prolonged use, the motors will
produce heat which is radiated
through the motors outer casing.
Do not touch the motors outer
casing for at least 30 minutes after
using the wheelchair, to allow it to
cool.
SUNRISE F16 Issue 8 6
Safety warnings
Wheelchair range
The range of your wheelchair can
be affected by many factors such
as user weight, terrain, ambient
temperature and battery condition.
The stated range in the sales
literature should be seen as the
theoretical maximum and may not
be attained by every user.
We recommend that every user
initially limit their journey to half the
stated range, until they have
confidence in the actual range their
wheelchair can attain. If your
battery indicator is showing a low
charge then do not attempt a long
journey unless you are confident in
reaching your destination and also
returning to your home without the
risk of being left stranded.
Use on a slope
Your wheelchair has been designed
and tested to allow its use on
slopes or gradients of up to 10°.
However, if you have the option of
adjusting the angle of seating with
either tilt seat or recline back, then
in certain circumstances your
wheelchair could become unstable.
Before attempting to climb or
decline a slope, we strongly
recommend that you return the
seat and back to an upright
position.
Use on a slope (continued)
Failure to do this may cause the
wheelchair to become unstable.
If you are in any doubt about the
capabilities of wheelchair on a
slope then do not attempt to drive
up or down the slope, try to find an
alternative route.
Mobile telephones and two way radios.
When operating cordless or mobile
telephones, two way radios, walkietalkies, C.B. Amateur Radio or
other transmitting devices, the
following must be noted:
Mobile telephones or two - way
radios devices must not be
used while operating the
vehicle.
Use of Mobile Phones or Two Way
Radios can cause excessively
strong electromagnetic fields. This
may interfere with the vehicles
electronic systems. If Mobile
Phones or Two Way Radios are
required to be used, the vehicle
must be brought to a halt and the
power turned off before any such
device is switched on or used.
7 SUNRISE F16 Issue 8
Preparing your wheelchair for use
Assembling the batteries
Slide in both batteries into the
motor unit as shown in Fig. 1.
Note: the batteries are shaped to
ensure that they cannot be
incorrectly fitted.
Connecting the batteries
The batteries are connected with
two plugs which are located at the
front of the motor unit (Fig. 2).
Note: Before using your vehicle
for the very first time, please
charge your batteries for a
peiod of 24 hours.
Fig. 1
Battery boxes being fitted to motor unit
Fig. 2
Battery connection plugs
SUNRISE F16 Issue 8 8
Preparing your wheelchair for use
Connecting the batteries to the
control unit
The batteries must next be
connected to the control unit which
is located at the front of the motor
unit.
Control pod/control box
connection
Connect the control pod plug into
the control box (Fig. 4).
In this state the power unit can be
driven carefully when switched on
and manoeuvred into a convenient
position to attach it to the frame,
ensuring that the control pod lead is
held safely to protect it from
damage.
Fig. 4
Fig. 3
Power lead
Control box plug
(behind plate)
9 SUNRISE F16 Issue 8
Preparing your wheelchair for use
Fig. 6
Armrests
The armrests on both sides of the
wheelchair can now be fitted.
Lower the armrests into their
receivers until they reach the
required position and push the
locking lever into the locked
position (Fig. 6).
Fig. 5
Locating pegs
Cups
Armrest receiver
Locking lever
Assembling the motor unit and
wheelchair
Remove the manual wheelchair
quick release wheels.
Connect the power unit to the
frame by locating the bottom pegs
on the frame (Fig. 5) into the cups
on the motor unit, and rotating the
motor unit towards the frame until
the locating pegs on the frame lock
into the holes in the motor unit.
Ensure the control pod lead is
protected during this process.
Note: the wheel and tyre have
been cut away in the illustration for
clarity.
Bottom pegs
SUNRISE F16 Issue 8 10
Fig. 8
Fitting footrests
Firstly, offer the footrest assembly
at right angles to the frame (Fig 8),
locate the stem into the frame tube
and swing assembly forward to lock
in position. To swing away the
footrest, simply depress the
retaining catch and turn the footrest
out. This can now be lifted out if
required.
Retaining catch
Fig. 7
Control Box
The control box is mounted on a
sliding mechanism which enables
the control to be moved forwards
and backwards (Fig 7). Slide the
extension arm into the sliding
mechanism and secure the slider
by tightening the locking lever. The
locking lever can be moved, if it is
inconveniently positioned by
pushing the centre knob and
rotating the lever to a less obtrusive
position.
Ensure the locking lever is fully
tightened prior to use and
especially when transporting
your wheelchair.
Power lead Control box
Preparing your wheelchair for use
Sliding
mechanism
Locking lever
11 SUNRISE F16 Issue 8
Adjusting footrest height
The footplate may be adjusted for
height (Fig. 9). To adjust, take out
the retaining bolt as shown with a
6mm Allen key and select a
comfortable position through one of
the adjustment holes in the angled
tube.
Refit the bolt and tighten securely
prior to use.
Footrest angled tube
Retaining bolt
Preparing your wheelchair for use
Fig. 9
Fig. 10
Adjusting armrest height/
removing
The armrest can be adjusted for
height whilst you are seated in the
wheelchair.
Move the locking lever to the
position shown in Fig. 10a and slide
the armrest pad to the desired
position, and rotate the lever to its
locked position.
To remove the armrest move the
locking lever to the position shown
in Fig. 10 and slide the complete
armrest upwards until it clears its
receiver.
Fig. 10a
Locking lever in height adjustment
position
Locking lever in 'remove'
position
SUNRISE F16 Issue 8 12
Fig. 11
Fig. 12
Preparing your wheelchair for use
Emergency freewheel
This is a mechanism which enables
the drive to be disconnected from
the motors in an emergency.
By lifting the handle upwards, the
drive becomes disconnected from
the motors (Fig. 11). This may only
be used in an emergency, or if you
need to manually push your
wheelchair.
It is not intended for permanent
use.
REMEMBER: the chairs
automatic braking system will
not work unless the handle on
the right hand side of the power
pack is pushed down.
ALWAYS RE-ENGAGE THE
EMERGENCY FREEWHEEL
AFTER USE
Seat sling tensioning
Your F16 wheelchair is fitted as
standard with a retensionable seat
(Fig. 12).
The seat sling can be re-tensioned
through the use of Velcro
®
panels
underneath the seat. Remove the
No 2 Philips screws retaining the
left side of the seat sling with a
No 2 Philips screwdriver, re-adjust
the Velcro
®
to bring the sling to its
correct tension. Replace the
screws.
Philips screws
Velcro
®
panels
Handle in 'Drive' position
Handle in 'Freewheel' position
13 SUNRISE F16 Issue 8
Pilot control
Proportional control
Your wheelchair is fitted as
standard with a side mounted
proportional control (Fig. 13). This
supplies a smooth flow of electrical
power to your motors via the
movement of the joystick. Push the
joystick gently forward to increase
forward speed.
When the joystick is at its full extent
your powerchair is travelling at full
speed as set by the speed setting
lever on the rear of the control box.
As the joystick is released the
wheelchair will automatically
engage motor brakes and stop. In
front of the joystick is a green pushbutton switch which turns the
controller on and off. Do not use
this switch to stop the wheelchair
except in an emergency.
Adjustable speed setting
The maximum power and speed of
your wheelchair can be adjusted by
turning the power setting control
lever anticlockwise to reduce
speed, and clockwise to increase
speed, this is useful when learning
or in tight situations (Fig. 14).
Fig. 13
Fig. 14
On/Off button
Battery gauge
Joystick
Adjustable speed setting
SUNRISE F16 Issue 8 14
Pilot control
Fig. 15
Operating the control joystick
When engaging the main on/off
switch, allow a few seconds prior to
moving the joystick. This allows the
system to self check. If you move
the joystick too soon, the battery
level indicator display will flash,
disabling drive to your wheelchair.
Whilst this is not harmful to your
wheelchair, you will need to switch
off and then back on to clear the
system (Fig. 15). To steer, simply
move the joystick in the direction
you wish to go. Proceed slowly at
first, i.e. do not push the joystick
too far forwards. Anticipation of the
direction of travel is soon acquired
and correction is then made
instinctively in the same way that a
car driver always turns the steering
wheel in the direction he wants to
go, even though the car and wheel
may want to go another way. Look
ahead when you are driving, and
not at the control but do remember
that only practice will enable you to
become proficient. Brakes will
operate as soon as the joystick is
released and allowed to return to its
centre position. On level ground,
this should bring you to a halt within
one chair's length. On a steep hill, it
may travel slightly further and you
will notice the brakes being
automatically applied when the
chair is nearly stationary.
Once the brakes have been
applied, switching off will make no
difference to the brakes, although it
is always safer when remaining
stationary for a period of time to
switch off.
If you need to do an emergency
stop, then switch off the on/off
switch. This will immediately apply
full braking and bring the chair to a
rapid halt.
15 SUNRISE F16 Issue 8
Pilot control
Summary
1. To steer, simply move the
joystick in the direction you wish
to go.
2. The further you move the
joystick, the faster you will go.
3. The speed setting knob
combined with the fast slow
switch adjusts the minmum and
maximum speed of the
wheelchair. Useful when learning
or in tight situations.
4. The brakes will automatically
stop the wheelchair from any
speed when the joystick is
released.
5. Switching off immediately
applies braking.
6. It is important that the chair is
stationary when changing
direction from reverse to forward.
7. Always switch to off before
getting out of the chair.
TruCharge battery gauge
(Pilot Control only)
This is a 10 segment illuminated
display which indicates if the
controller is turned on and also
gives the status of the battery, the
controller and the wheelchair
electrical system (Fig. 16).
Red, yellow and green bars lit:
Battery charged; controller and
electrical system OK.
Red and yellow bars lit:
Charge battery if possible;
controller and electrical system OK.
Red bars only lit or slow flash:
Charge battery as soon as
possible; controller and electrical
system OK.
Rapid flash of bars:
Indicates a fault in the controller or
electrical system. See inset for fault
diagnostics.
Ripple up and down of bars:
Joystick displaced at turn on.
Fig. 16
Description
high battery voltage
Solenoid brake fault
Possible controller fault
Possible joystick fault
Charger connected
Right motor wiring fault
Right motor disconnected
Left motor wiring fault
Left motor disconnected
Low battery voltage
Fault type
G
R
E
E
N
Y
E
L
L
O
W
R
E
D
The
number of
flashing
bars
indicate
the
possible
area of
fault
SUNRISE F16 Issue 8 16
The Penny and Giles Pilot + control pod
Control pod
The control pod is mounted on a
sliding mechanism, which enables
the control to be moved forward or
backwards (Fig. 17). When the
most comfortable position has been
selected, secure the slider by
tightening the locking Allen screw,
using an Allen key.
Ensure the locking screw is
fully tightened prior to use and
especially when transporting
your wheelchair.
The pod can also be swung away
at right angles to the armrest to
allow the chair to move close to
tables.
Power lead attachment
The power lead must also be
plugged into the socket as shown in
Fig. 18.
Note: When unplugging the power
lead pull off by gripping the outer
plastic cover.
Never pull the cable to
disconnect the plug.
Fig. 18
Power
supply
Outer cover
Fig. 17
Slide adjustment
screw
Sliding arm
17 SUNRISE F16 Issue 8
The Penny and Giles Pilot + control pod
Fig. 19
Fig. 20
Power supply
Ensure the power lead is connected
correctly into its socket on the rear of
the control pod (Fig.19).
The immobiliser plug
When this is activated the chair will
not function, other than the hazard
warning light system. This may be
useful if you wish to leave your
wheelchair unattended (Fig.19).
To activate the immobiliser
1. Insert the immobiliser plug into
the charger/programmer socket
located on the front of the control
pod.
2. Turn on remote.
3. Pull out immobiliser plug.
4. Your chair should now be
immobilised.
To de-activate the immobiliser
1. Turn on remote.
2. Insert the immobiliser plug.
3. Pull out after a few seconds.
4. Your chair should now be ready
to use.
Immobiliser
plug
Charger
programmer
socket
On/Off
button
SUNRISE F16 Issue 8 18
The Penny and Giles Pilot + control pod
Adjustable speed setting
Your controller has five speed
settings.
To adjust:
1. Press the mode button until the
speed settings indicator is
flashing (Fig.21)
2. Increase or decrease the speed
setting by pushing the joystick to
the left or right respectively, until
the required setting is obtained.
To activate the setting either
push the joystick forwards to
drive or press the mode button
until the flashing lights are no
longer flashing.
3. When the third or middle speed
indicator light is selected on a
10 km/h chair the vehicle is set
at 4mph. Please note that this
is the maximum speed
permitted for pavement use.
Battery level indicator
This has ten colour coded lights,
3 red, 4 orange, and 3 green, and
denotes the state of charge of the
batteries (Fig.22). Green is high,
Orange is low, and Red is
dangerously low. The most
accurate reading is attained when
the chair is stationary and on a
level surface. The lights also help
indicate the position of a fault
(should the need arise). When in
fault the light will flash quickly.
Noting the number of lights flashing
may help your service agent in
simple fault finding.
Fig. 21
Fig. 22
Adjustable speed
setting indicator
showing 4mph mode
19 SUNRISE F16 Issue 8
The Penny and Giles Pilot + control pod
Indicators
The right hand button operates the
right side, front and rear indicators,
the left button operates the left
side, front and rear indicators.
To cancel press the button again
(Fig.23).
Fig. 23
Fig. 24
The horn button
When pressed the horn buzzer will
sound, it stops when you release
the button (Fig.24).
Left indicator
button
Right indicator
button
SUNRISE F16 Issue 8 20
The Penny and Giles Pilot + control pod
Hazard lights
Depressing the button will operate
the front and rear hazard lights.
This is effective either when the
chair is switched On or Off. The two
indicators will flash intermittently
until cancelled by pressing the
button again (Fig.25).
Fig. 25
Fig. 26
Hazard lights button
Main lights
Depressing this button will operate
the lights (Fig.26) only when the
chair is switched on.
Pressing it again will switch the
lights off.
21 SUNRISE F16 Issue 8
The Penny and Giles Pilot + control pod
Actuator mode function
This will be included on your
remote control pod if you have one
or more electric options fitted to
your chair. Refer to Fig.27.
Menu select
To chose an electric option press
the mode button until the red lights
are visible on the wheelchair
diagram next to the joystick. Move
the joystick to the left or right to
indicate which function can be used
Legrest left Backrest recline
Seat tilt
Legrest right Both legrests
When the desired function has
been chosen you can activate the
electric actuator system.
If you attempt to operate the
electric functions when driving, the
chair will automatically come to a
safe stop. We recommend you only
use the electric options whilst
stationary.
Up/down movement
Once the relevant electric option
has been chosen the required
movement is achieved by moving
the joystick forwards or backwards.
Programme port
This will enable an approved
service agent to reprogramme your
chair and also gain useful
information when tracing any faults
(Fig.28).
Fig. 27
Fig. 28
Red
indicator
lights
Programme port
SUNRISE F16 Issue 8 22
The Penny and Giles Pilot + control pod
Charging socket
See section on charging.
Operation the control joystick
When engaging the main On/Off
switch, allow a few seconds prior to
moving the joystick. This allows the
system to self check. If you move
the joystick too soon, the battery
level indicator display will flash,
disabling drive to your wheelchair.
Whilst this is not harmful to your
wheelchair, you will need to switch
off and then back on to clear the
system.
To steer, simply move the joystick
in the direction you wish to go.
Proceed slowly at first, i.e. do not
push the joystick too far forward.
Brakes will operate as soon as the
joystick is released and allowed to
return to its centre position. On
level ground, this should bring you
to a halt within one chair’s length (6
km/h model). On a steep hill, it may
travel slightly further and you will
notice the brakes being
automatically applied when the
chair is nearly stationary. Once the
brakes have been applied,
switching off will make no
difference to the brakes, although it
is always safer when remaining
stationary for a period of time to
switch off.
Note: If you need to stop in
an emergency, the simplest
and safest way is to just
release the joystick. This will
being the chair to halt in a
controlled manner.
A second means of bringing
the chair to a halt is to press
the On/Off switch. This
method is not recommended
as the chair will stop very
abruptly and will cause
unnecessary wear in the
chairs braking system.
23 SUNRISE F16 Issue 8
The Penny and Giles Pilot + control pod
Summary
1. To steer, simply move the
joystick in the direction you wish
to go (Fig. 29).
2. The further you move the
joystick, the faster you will go.
3. New users should use slower
speeds until they are confident
when driving the power chair.
Adjust the speed range as
explained on the previous
pages.
4. The brakes will automatically
stop the wheelchair from any
speed when the joystick is
released.
5. Switching off immediately
applies braking and is not
recommended for normal use.
6. It is important that the chair is
stationary when changing
direction from reverse to
forward.
7. Always switch to off before
getting into or out of the chair.
Fig. 29
SUNRISE F16 Issue 8 24
Parallel Swing Away Arm
Before adjusting the swing-away
arm, switch off the controller to
avoid accidental displacement of
the joystick which would cause
unwanted movement of your
wheelchair.
Gently apply pressure to the side of
the controller nearest the user and as
close as possible to the front of the
controller .
The controller will move outward and
then backward before reaching its
fully back position.
Keep your fingers and clothing,
etc., clear while operating the
swing-away mechanism.
If required, your wheelchair can be
operated with the swing-away
mechanism in its fully back position,
but only for slow manoeuvering such
as positioning the wheelchair closer
to table tops, etc.
To revert to the normal driving
position, switch off the power and pull
the arm outwards and then forwards
before returning the arm to its ‘home’
position. Make sure the controller is
fully engaged in its home position
before switching on and operating
the wheelchair in the normal manner .
Caution
Do not hang any items on or over
the parallel swing-away remote
assembly as this could damage
the swing-away mechanism.
When transferring to and from
the wheelchair do not use the
remote as a means of support.
Fig. 30
Warning
Keep fingers, clothing, etc., clear
of the swing-away mechanism at
all times.
Ensure the power is switched off
while adjusting the parallel
swing-away arm.
Only operate the wheelchair at
low manoeuvring speed when
the parallel swing-away is in use.
25 SUNRISE F16 Issue 8
Batteries
Your Sunrise Medical wheelchair
batteries are supplied as standard
in two battery boxes, housed in the
motor unit behind the seat (Fig. 31).
They do not have to be removed for
charging.
Fig. 31
Fig. 32
Safety cut-out switches
In the event of a short circuit there
are safety systems built into your
wheelchair to safeguard your
electrical circuits. Cut-outs are
positioned on both battery boxes
(Fig. 32) and automatically cut off
the power. Inspect the cut-out
buttons and you will see which has
tripped by the extension of the
button. After a few seconds push
the button in to resume. If problems
persist contact your local Sunrise
Medical Service dealer.
Charging
point
Battery
boxes
Safety cut out push buttons
Batteries and charging
SUNRISE F16 Issue 8 26
General information
Batteries are the power source for
almost all of the modern mobility
products available today. The
design of batteries used in mobility
products is significantly different to
the batteries used to start a car for
example. Car batteries are designed
to release a large amount of power
over a short period of time, whilst
mobility batteries (commonly called
deep cycle batteries) release their
power evenly, over a long period of
time. Therefore, due to the lower
production volumes and increased
technological requirements,
mobility batteries are typically more
expensive.
Commonly two 12 volt batteries are
used together in a mobility product,
giving a total voltage of 24 volts.
The size of the battery, (e.g. its
available power) is expressed in
amps per hour e.g. 30amp/hr. The
higher the number, the bigger the
battery size, weight and, potentially,
the greater the distance you can
travel.
Sunrise Medical only fit as standard
maintenance free batteries into this
type of wheelchair.
Batteries and charging
Maintenance free batteries
This type of battery uses a method
of carrying the electrolyte
commonly referred to as ‘gel’, that
is held within the battery case. As
the name implies, no maintenance
is required other than regular
charging. You can safely transport
this type of battery without fear of
acid spilling.
Furthermore, they are approved for
transportation on aircraft.
Battery care
Below is set out a battery care plan
for maintenance free batteries. This
has been agreed between Sunrise
Medical and the battery
manufacturers, to enable you to get
the best out of your batteries. If a
different care plan is followed, this
may result in lower than expected
performance from your mobility
vehicle.
27 SUNRISE F16 Issue 8
Batteries and charging
Maintenance free battery care
plan
1 Only use an approved Sunrise
Medical charger compatible with
the vehicle to be charged.
2 Charge your batteries every
night, regardless of the amount
of use your mobility device has
had during the day.
3 Do not interrupt the charging
cycle.
4 If your mobility device is not
required for use, it should remain
connected to the charger until
required. This will not damage
your batteries, so long as the
mains socket/plug is left
switched on. Turning the mains
socket/plug off, but leaving the
mains cable plugged in will
eventually deplete your battery
charge.
5 If you leave your vehicle for an
extended period (more than 5
days) disconnect the main
battery lead.
6 Failure to allow for recharge will
damage the batteries and can
lead to shortened distances and
premature failure.
7 Do not top up the charge of your
batteries during the day. Wait
until the evening for a full
overnight charge.
8 As a general rule, maintenance
free batteries take longer to fully
charge than lead acid batteries.
9 The battery terminals need to be
checked regularly for signs of
corrosion. If any corrosion is
apparent, then clean the
terminals completely (a wire
brush is ideal) and re-grease the
terminal using Vaseline
petroleum jelly, not ordinary
grease. Ensure that the terminal
nut and bolt, cable clip and
exposed cable are completely
covered with jelly.
10Following all the points above
should result in a healthier
battery, greater range for the
vehicle user and a longer life for
your batteries.
Do not expose any part of the
battery to direct heat (i.e. naked
flame, gas fire).
When charging always place on
a hard surface in a room with
good ventilation.
You should not charge your
batteries in outdoor conditions
SUNRISE F16 Issue 8 28
Batteries and charging
Fig. 33
General
The external charger (Fig. 33) has
been designed to charge two
12 volt Sonnenschien Dryfit Gel
type batteries.
Safety features
The chargers have features which
prevent hazards or accidents
occurring as a result of connecting
batteries the wrong way round,
overheating caused by fault
conditions, or attempting to charge
wrong voltage batteries.
The majority of charger sizes are
electrically double insulated and no
earth connection is required. Some
larger sizes may be electrically
earthed and this will be clearly
stated on the label.
The 3 pin UK mains input plug
contains a replaceable fuse. The
rating of this fuse is shown on the
charger label. Always replace with
the same type and size of fuse as
specified. Fitting of different fuses
can result in damage to the charger
or failure of the charger to operate
properly.
If your charger has been specified
for use in Continental Europe it will
contain a European two pin plug
which does not have a fuse. In this
case the fuse is located in the
fascia panel of the charger.
24V 8A external
29 SUNRISE F16 Issue 8
Fault finding guide for 24V 8A
charger
DANGER! DO NOT REMOVE
THE UNIT COVER, SPECIALIST
SKILLS AND EQUIPMENT ARE
NECESSARY FOR REPAIR.
Fault: The yellow “charging”
lamp is not illuminated
Check that the 13A mains plug is
properly mated with the mains
outlet socket and that the mains
supply is switched on. If the lamp
remains off consult Sunrise Medical
or your local Sunrise Medical
dealer.
Fault: The charger is switched
on but the red “failure” lamp is
illuminated
Check that the charger connections
are correct and that the plugs are
fully mated in the sockets. If the
lamp remains illuminated it is
possible there is a fault in the
battery, consult Sunrise Medical or
your local Sunrise Medical dealer.
Fault: The red “failure” lamp
blinks
The battery voltage is too low, try
again after approximately 30
minutes. If the lamp continues to
blink consult Sunrise Medical or
your local Sunrise Medical dealer.
24V 8A charger indicator lights
The charger has 3 light indicators,
each clearly marked on the label to
show their function (Fig. 34).
Yellow - charging
This will illuminate a few seconds
after connection, indicating that
charging of the batteries is taking
place.
Green - charge complete
This will illuminate when the battery
is fully charged. This can be
anywhere from 8.5 hours to 14.5
hours after commencement of
charging, depending on how
discharged the batteries were. The
‘mains’ light will remain on.
Please note that after the charge
complete light has illuminated, the
charger will continue to charge the
batteries. However the charging and
‘bulk charge’ complete light will not
be illuminated at this point. Following
a further period of time the charger
will switch to a ‘float voltage’ setting.
It can therefore be left on indefinitely.
Red - fault light
Battery voltage too low, try again
after 30 mins.
Batteries and charging
SUNRISE F16 Issue 8 30
Fig. 34
Fig. 35
Batteries and charging
Charger socket
Control box
Yellow
‘mains on’
Orange
‘charging’
Yellow
‘bulk
charge
complete’
Green
‘charge
complete’
24V 6A external
Procedure for connecting the
charger
1 Plug into the three pin charging
point under the front of the
control box (Fig. 34).
2 Connect the charger to the
mains supply by means of the
mains plug and switch on
(Fig.34). The yellow ‘mains on’
indicator should light up
immediately (Fig. 35), followed
shortly afterwards by the orange
‘charging’ indicator.
3 The battery is fully charged
when the green ‘charge
complete’ light illuminates. if not
needed for use the battery may
be left charging indefinitely
without risk of damage.
4 If the chair is required for use
before the ‘charge complete
light’ shows, then it is possible to
obtain restricted use once the
‘bulk charge’ light has
illuminated. At that point the
battery is about 85% - 90%
charged. It is essential to provide
a full recharge at the first
opportunity.
5 Do not leave the charger
connected to the battery with the
mains disconnected or switched
off. This could result in damage
to your battery being caused by
deep discharge over a period of
time.
6 Always switch off at the mains
before disconnecting the
batteries.
31 SUNRISE F16 Issue 8
Batteries and charging
Safety and caution notes
1 The charger is designed for
indoor use. Do not use outdoors
or expose to rain, snow, spray or
moisture.
2 Use only with Sonnenschein
dryfit Gel type batteries of the
A200, A500 or A500C groups
when employed in cyclic mode.
3 The charger may be used with
other brands of Gel type
batteries, subject to written
confirmation from the Technical
Department of Sunrise Medical.
4 Do not smoke, or create sparks
or flames in the vicinity of the
batteries.
5 Avoid standing the charger on
carpets or rugs during use and
do not cover the ventilation slots
of the charger or allow objects to
rest on the case.
6 Do not attempt to recharge other
types of batteries such as car
batteries, non-rechargeable
batteries, AGM sealed batteries,
wet electrolyte batteries or
batteries of the wrong voltage.
7 Repairs should only be carried
out by Sunrise Medical.
8 The charger is designed for
mains input voltages of 220V AC
to 240V AC, for chargers to
operate with 110V AC (in
countries such as USA or North
America), a different charger will
be needed, please consult local
Sunrise Medical Dealer.
9 Use of an attachment, not
recommended or sold by
Sunrise Medical, may result in a
risk of fire, electric shock or
injury to persons. To reduce the
risk of damage to electric plug
and cord, pull by the plug rather
than the cord when disconnecting
the charger. Make sure the cord
is located so that it will not be
stepped on, tripped over, or
otherwise subjected to damage
or stress. An extension cord
should not be used unless
absolutely necessary. Use of an
improper extension cord could
result in a risk of fire and electric
shock. If any extension cord
must be used, make sure the
pins on the plug of the extension
cord are the same number, size
and shape as those of the plug
on the charger; and that the
extension cord is properly wired
and in good electrical condition.
SUNRISE F16 Issue 8 32
Never Charge a frozen battery. A
fully charged battery will rarely
freeze but the electrolyte of a
discharged battery can freeze at
16
O
Fahrenheit (-9O centigrade),
any battery that is suspected of
being frozen should be thawed
completely before charging.
Note: when buying replacement
batteries always consult your
sunrise medical service agent.
Note: Before using your vehicle
for the very first time, please
charge your batteries for a
period of 24 hours.
Battery warranty
Battery warranties are subject to
periods set by the manufacturers,
however, most of these warranties
are subject to a wear and tear
clause, and if you genuinely wear
out your batteries in 6 months, it
will not be possible to obtain a
replacement under warranty.
Batteries and charging
Important !
Do not rest a battery on top of the
charger.
Do not stand the charger on a
carpet or other soft surface. Always
place it on a hard surface.
Do not operate the charger if it has
received a sharp blow, been
dropped or otherwise damaged in
any way, take it to a qualified
technician.
Do not disassemble charger; only
have it repaired by the
manufacturers. Incorrect reassembly may result in a risk of
electric shock or fire. To reduce the
risk of an electric shock, unplug the
charger from the outlet before
attempting any maintenance or
cleaning.
Turning off the controls will not
reduce the risk.
Never place the charger directly
above the battery being charged;
gases from the battery will corrode
and damage the charger.
Never Smoke or allow a spark or
flame in the vicinity of battery or
charger. Be extra cautious to
reduce the risk of dropping a metal
tool on to the battery. It could spark
or short circuit the battery or other
electrical parts, that may cause an
explosion. Also take off all personal
metal effects and dangling objects
when working on the battery.
33 SUNRISE F16 Issue 8
Batteries and charging
7 Lots of start/stop driving.
8 Also thick pile carpets within the
home can affect range.
All this technical information may
seem complicated and a little
daunting, but please remember,
that the battery sizes available on
each Sunrise Medical product
should give sufficient range to cope
with the majority of customer’s
lifestyles.
The range of your vehicle
Most manufacturers of mobility
products state the range of their
vehicles either in the sales
literature or within the Owners
Manual. The range stated
sometimes differs from
manufacturer to manufacturer even
though the battery size is the same.
Sunrise Medical measure the range
of their vehicles in a consistent and
uniform manner, but variances still
occur due to motor efficiencies and
overall product load weight.
The range figures are calculated to
I.S.O. Standard 7176. Part 4:
Wheelchair Energy Consumption
Theoretical Range
This test is carried out in controlled
conditions with new, fully charged
batteries, on a level test surface
and a user weight of 75kg. The
range figures stated should be
seen as a theoretical maximum and
could be reduced if any single, or
combination, of the following
circumstances occur:
1 User weight heavier than 75kg.
2 Batteries whose age and
condition are less than perfect.
3 The terrain is difficult e.g. very
hilly, sloping, muddy ground,
gravel, grass, snow and ice.
4 The vehicle climbs kerbs
regularly.
5 The ambient temperature is very
hot or very cold.
6 Incorrect tyre pressures in one
or more tyres.
Myths and legends
Over the years, battery technology
has moved forward but,
unfortunately, some of the advice
given on battery care has not. This
has resulted in a number of
confused and at times contradictory
instructions on the ‘best’ way to
care for your batteries. This section
will help to dispel some of these
myths and legends.
1 Batteries can be charged
immediately after use. You do
not need to allow them to cool
prior to charging.
2 Mobility batteries do not develop
a memory from using a repetitive
charge and discharge cycle.
This only applies to nickel
cadmium batteries commonly
found in products such as
camcorders.
3 Batteries when new do not
require any special attention with
regard to their charge and
discharge cycle. Following the
relevant ‘care plan’ is the best
advice we can give.
SUNRISE F16 Issue 8 34
User tips
Fig. 36
Caution
Please show the utmost consideration
for the other traffic on the road.
Remember that the last thing a car
or lorry driver expects to see is a
wheel chair backing off the kerb
into the road. If in any doubt, do not
risk crossing the road until you are
certain that it is safe.
Always cross the road as quickly as
possible; there may be other traffic.
Adverse conditions
Please be aware that when driving
your wheelchair in adverse
conditions, e.g. on wet grass, mud,
ice, snow, or other slippery
surfaces you may experience a
reduction in the grip and traction of
your wheelchair. We recommend
you take extra precautions in these
conditions, particularly on hills and
slopes, your wheelchair could
become unstable or skid causing
possible injury. Extreme variances
in temperature may trigger the self
protect mechanism in the control
system. If this occurs the control
system will temporarily shut down
to prevent damage to the
electronics or the chair.
Ramps
When using a ramp, please ensure
that is capable of taking the
combined weight of the powerchair
and yourself. If a ramp is being
used to load a chair into a vehicle,
please ensure the ramp is properly
secured to the vehicle. Always
approach the ramp head-on and
exercise caution (Fig. 36).
35 SUNRISE F16 Issue 8
User tips
Fig. 37
Transfer to and from the chair
Sunrise Medical recommend that
you consult your healthcare
professional for assistance in
developing your personal front or
side transfer technique to best suit
your needs, and avoid any personal
injury (Fig. 37 and 38).
Fig. 38
SUNRISE F16 Issue 8 36
User tips
Gradients: ascents
When going uphill, keep the chair
moving. Keep the joystick pushed
well forward and steer by moving it
from side to side. If you have
stopped on a hill, then you should
start slowly, and if necessary lean
forward to obviate the tendency for
the front wheels to lift (Fig. 39).
Fig. 39
Fig. 40
Gradients: descents
On descents, it is important not to let
the wheelchair accelerate beyond
its
normal level of ground speed. In fact,
it is safer to proceed slowly down
steep descents and stop immediately
if any anxiety arises regarding
directional control. If the chair picks
up speed, centre the control to slow it
or to stop all forward movement, then
restart slowly and do not allow the
speed
to increase. The solid state
controller
has the benefit of a logic
system, that will help compensate
when driving along a camber or up a
hill. This is an added safety feature
on your wheelchair . In addition of
course, you may control the
wheelchair speed by using the speed
control (Fig. 40).
37 SUNRISE F16 Issue 8
T ransporting your chair
Disassembly
Your F16 can be disassembled for
transporting, this is performed in
the opposite method of assembly
and should be done in the following
sequence:
1 Remove the footrests
(see page 10).
2 Remove the control pod by
loosening the locking lever
(see page 10) and sliding the
assembly out of the sleeve.
3 Remove the motor/battery unit
by pulling the release cord
(Fig. 41) and holding the frame
and rolling the frame away from
the power unit. Allow the power
unit to slowly rock back on to the
stabiliser wheels.
Note: Do not stand too close to
the power unit when the motor
unit rocks back.
4 Fold the frame by standing to
one side and pulling the side
rails together. This may now be
stowed.
5 Disconnect the control pod from
the power unit by unplugging the
control cable from the control
box (Fig. 42).
N.B. never pull the plug using the
cable, always grip the plug body.
6 You may now stow or transport
the wheelchair.
If you wish to complete the
disassembly follow the next
instructions.
7 Disconnect both battery plugs
(Fig 42).
8 Slide out both batteries.
Release
cord
Fig. 41
Fig. 42
Control box plug
(behind plate)
Power lead
SUNRISE F16 Issue 8 38
T ransporting your chair
Transportation in vehicles
Users should not sit in the
wheelchair while riding in any
and all means of transportation.
Only permanently installed car
seats and seat belts will offer
sufficient protection in hazardous
situations. When vehicles are in
motion, unoccupied wheelchairs
should be secured using
appropriate means.
39 SUNRISE F16 Issue 8
Lap belt instructions
Before using your wheel-
chair ensure the seat belt is
worn and correctly adjusted
before use.
The lap belt is fitted to the wheelchair
as shown in the illustrations. The lap
belt is fitted between the armrest
support and the backrest tube. The
belt should then be run across the
outside of the back upholstery.
It is important that the belt
is routed around the back of
the wheelchair. The buckle end
can be fed between the armrest and backrest.
Adjust the lap belt to suit the user’s needs as follows:
To increase the belt length:
Feed the belt through slide adjusters and male buckle to provide
more belt length.
To reduce the belt length:
Feed the belt back through male
buckle and slide adjusters.
Ensure the belt is not looped at the
male buckle
SUNRISE F16 Issue 8 40
Lap belt instructions
When fastened check space
between the lap belt and the user,
when correctly adjusted it should be
possible to insert the flat of the hand
between the lap belt and the user.
Generally the Lap Belt should be
fixed so that the straps sit at an angle
of approximately 45°, and when
correctly adjusted should not allow
user to slip down in the seat.
To fasten buckle: -
Firmly push the male buckle into
female buckle
To release belt: -
Press the exposed sides of the
male buckle and push towards the
centre whilst gently pulling apart.
Do not rely on the lap belt
only when the wheelchair and
occupant are transported in a
vehicle, use the separate occupant lap and diagonal restraints
provided in the vehicle.
Advice to Client
The lap belt must be checked on a
daily basis to ensure it is adjusted
correctly and it is free from any
obstruction or adverse wear.
Failure to make sure that
the lap belt is secure and
adjusted prior to use could
cause serious injury to the
user. E.g. too loose a strap may
allow the user to slip down in
the chair and risk suffocation.
Maintenance
Check lap belt, and securing
components; at regular intervals
for any sign of fraying or damage.
Replace if necessary.
Clean the lap belt with warm soapy
water and allow to dry.
41 SUNRISE F16 Issue 8
Lap belt instructions
Note
The lap belt should be adjusted
to suit the end user as detailed
above
Sunrise Medical also
recommend that the length and
fit of the belt is checked on a
regular basis to reduce the risk
of the end user inadvertently
re-adjusting the belt to an
excessive length
If in doubt about the use
and operation of the seat belt
then ask your healthcare professional, wheelchair dealer,
carer or attendant for assistance.
SUNRISE F16 Issue 8 42
Maintenance
Cleaning
The wheelchair should be wiped
over once per week with a slightly
damp, not wet, cloth and any fluff or
dust that has accumulated around
the motors should be blown or
dusted away.
Tyre pressures
If pneumatic tyres are fitted to your
wheelchair it is important to
regularly check the air pressure
and for signs of wear.
The correct pressures are between
the minimum of 137 kiloPascals
(20 psi, 1.37bar) and the maximum
241 kiloPascals (35 psi,2.41bar) for
rear wheels, and 102 kiloPascals
(15psi, 1.02 bar).
The pressure will need to vary,
depending on the weight of the
user. IT IS IMPORTANT that front
wheels are inflated to the same
pressure as a pair, and likewise the
rear. The inflator pump provides the
safest method of inflating your
wheelchair tyres and the pressure
can be checked with a standard
motor vehicle pressure gauge.
Do not inflate beyond the
maximum tyre pressure.
Electrical connections
When inspecting electrical
connections, pay attention to the
battery connections, the connection
of batteries to power loom and plug
in sockets for the joystick, control
box and lights and indicators.
Tyre wear
When inspecting the tyres for signs
of wear, look for significant scuff
marks, cuts and a diminished tyre
tread. Tyres will need to be
changed when the tread cannot be
seen over the complete surface of
the tyre.
Upholstery/seating
Tears, dents, wearing or slackening
of upholstery particularly near to
metal could result in poor posture
or lower levels of comfort and
pressure relief.
Authorised Sunrise Medical
service agents
The annual full service must be
performed by an approved Sunrise
Medical Service Agent. For a list of
approved service agents in your
area please contact Sunrise Medical
on this telephone number:
01384 44 66 88
Storage
When storing your powerchair for
long periods of time (in excess of
one week), first fully charge, and
then disconnect the batteries, to
minimise battery discharge.
PLEASE NOTE - NEVER
INFLATE THE TYRES
USING A GARAGE
FORECOURT AIRLINE,
ALWAYS USE THE
PUMP PROVIDED.
43 SUNRISE F16 Issue 8
To order spare parts.
PLEASE QUOTE THE
FOLLOWING:
1. Model of chair
2. Serial number of chair
3. Left hand or right hand control
4. Part number and description
and quantity of items required
5. State colour when ordering
upholstery or frame parts.
Charge batteries
Check battery level indicator
Ensure all removable parts are securely fastened
Electrolyte level check (wet batteries only)
SAFETY MUST BE OBSERVED!
Ensure all electrical connections are made, and firm
Wipe vehicle with a damp cloth
Check tyre pressures
Ensure lights and indicators
are operational and clean
Check tyres for wear
Battery terminals inspection. Clean and protect
with petroleum jelly. SAFETY MUST BE OBSERVED!
Check condition of upholstery and seating
Complete inspection, safety check and service
should be made by an authorised Sunrise Medical
agent.
F16 maintenance and rouitine
inspection
Maintenance
DAIL Y
WEEKL Y
MONTHL Y
QUARTERL Y
SIX MONTHL Y
ANNUALL Y
SUNRISE F16 Issue 8 44
YEAR 1 2 3 4
Service dates
Upholstery
Seat
Back
Armpads
Electrics
Condition
of loom
Connections
Lights (where
fitted)
T est run
Forwards
Reverse
Emergency
stop
Left turn
Right turn
Up/down slope
Over obstacles
Parking brake
(where fitted)
List items repaired/adjusted
YEAR 1 2 3 4
Service dates
Controller
On/off switch
Output plug
Operation
Dynamic braking
Programmable
settings
Batteries
Levels
Connections
Discharge test
Wheels/tyres
Wear
Pressure
Bearings
Wheel nuts
Motors
Wiring
Noise
Connections
Brake
Brushes
Chassis
Condition
Steering
Customer Name.
Address
Postcode
Service history
Date chair purchased
Model
Colour
Serial No.
Dealer stamp
Date: Signed:
Dealer stamp
Date: Signed:
Dealer stamp
Date: Signed:
Dealer stamp
Date: Signed:
This section is designed to assist you in keeping a record of any service and repairs to your Wheelchair. Should you
decide to sell or exchange your vehicle in the future, this will prove most helpful to you. Your Service Agent will also
benefit from a documented record and this manual should accompany the Wheelchair when service or repair work is
carried out. The Service Agent will complete this section and return the manual to you.
45 SUNRISE F16 Issue 8
Sunrise Medical
Your new F16 wheelchair is manufactured in the West Midlands by Sunrise
Medical. With over 30 years experience, we are one of the longest
established mobility equipment manufacturers in the UK. All our Scootas,
Wheelchairs, Powerchairs and Stairlifts undergo rigorous tests to ensure
that they meet our requirements of comfort, safety and durability. Our
success is based on the strong traditions of quality, value for money and
genuinely caring for our customers.
We pride ourselves not only on designing and building the most innovative
products, but also on our commitment to offer an excellent standard of
customer service both during and after sale.
In addition to your new F16 wheelchair, Sunrise also manufactures oxygen
concentrators, nebulizers and hoists. We have a vast range of aids to daily
living which include the Merlin Bath Lifter, bed accessories and walking
sticks.
Should you require any information on our full range of products please call
us on 01384 44 66 88 or contact us at:
Sunrise Medical Limited
High Street Wollaston
West Midlands DY8 4PS
www.sunrisemedical.co.uk
Sunrise Medical Limited
High Street Wollaston West Midlands DY8 4PS
England
Tel 01384 4466 88 Fax 01384 44 66 99
www.sunrisemedical.co.uk
Loading...