Electric Grass Trimmer
Electric Grass Trimmer
Model No. TRJ609E
A Division of Snow Joe, LLC
m CAUTION!
Before using this electric tool, carefully read and observe the
safety rules and instructions listed below. Before starting work,
make sure that you know how to stop the machine in case of
an emergency, The incorrect use of this machine could cause
serious injury. Keep these instructions in a safe place and on
hand so that they can be consulted when required.
m CAUTION!
The grass trimmer should only be used for cutting lawns and
along the borders of ower beds. Other uses of the trimmer,
not in these instructions, could damage the trimmer or
seriously injure the operator.
GENERAL Safety Rules
• The grass trimmer must not be used by anyone under the
age of 16.
• Always make sure the trimmer is in proper working
condition before use.
• Before connecting the trimmer to the electric outlet, make
sure that the rotating parts are not damaged.
• Do not use the trimmer if the cutting device is not secured
properly or is damaged.
• Before starting the trimmer, make sure that the blade is not
touching stones or debris.
• Always wear suitable clothing when using the trimmer to
prevent head, hand, or feet injuries. Use a helmet, safety
spectacles or goggles at all times when this tool is plugged
in. High boots (or sturdy shoes and trousers) and work
gloves are recommended.
• When the trimmer is in operation, keep the cutting section
away from all parts of the body.
• Do not start the trimmer when it is upside down or when not
in working position.
• Turn the trimmer off and disconnect the plug when: the
trimmer is not being used; it is left unattended; it is being
examined because it is not working correctly; the power
supply cable is damaged; the trimming line spool is being
removed or changed or when the trimmer is being moved
from one place to another.
• Keep children, other people, and pets away from the
trimmer; the grass which is cut and dispersed may contain
stones and debris.
• Do not let other people or animals come within 20 feet of
the trimmer when in use.
• Remain in a stable and secure position while operating
the trimmer.
© 2011 by Snow Joe, LLC
All rights reserved. Original instructions.
Form No. SJ-TRJ609E-880E
OPERATOR’S MANUAL
• Keep the area being cut free from wires, stones, and debris.
• Do not cut against hard objects. This could cause injury or
damage the trimmer.
• Use the edge of the guard to keep the trimmer away from
walls, surfaces, miscellaneous things, and delicate objects.
m CAUTION!
The guard is critical to the safety of the operator and people
near the trimmer. The guard keeps the trimmer in good working
order and must always be in place during operation. Failure to
have the guard in place during operation is dangerous and will
void the warranty.
• Be careful of the line, which can give deep cuts.
• Avoid accidentally starting – Don’t carry plugged-in tool
with nger on trigger.
• Do not force the tool – At a rate faster than the rate at
which it is able to cut effectively.
• Use the right tool – Do not use this tool for any job except
that for which it is intended.
• Don’t overreach – Keep proper footing and balance at
all times.
• Do not try to stop the cutting device with your hands.
Always let it come to a stop by itself.
m CAUTION!
The trim line spool will continue to rotate after turning the
trimmer OFF. Wait until the trim line spool has completely
stopped before making contact.
• Only use the type of line originally provided with the trimmer.
• Do not use the trimmer to cut grass which is not in contact
with the ground.
• Do not switch the grass trimmer on in enclosed or poorly
ventilated spaces or in the presence of inammable and/or
explosive substances such as liquids, gas, and powders.
• The user of the grass trimmer is responsible for any damage
sustained by third parties which has been caused by the
grass trimmer within the working area.
• Only cut during broad daylight or with corresponding
articial light.
• Do not cross roads or gravel paths with the trimmer
still running.
• When the trimmer is not in use, store it in a dry place and
out of the reach of children.
• The trimmer must be operated vertical, perpendicular to
the ground.
• Check regularly that all screws are properly secured.
SAVE THESE INSTRUCTIONS
1
Electrical Safety Rules
• The voltage must correspond to the one marked on the
technical data plate (120V~60Hz). Do not use other sources
of power.
• The power line should have a circuit-breaker no lower than
10A. Consult an electrician.
• Don’t abuse cord – Don’t yank cord from power supply.
Keep cord from heat, oil, and sharp edges.
• Never pass the grass trimmer over the extension cable
when the grass trimmer is working as this could cut the
cable. Mark sure you always know where the cable is.
• Use the special cable holder for the connection of the
extension cable.
• Never use the trimmer when it is raining, avoid moisture and
humidity. Do not leave the trimmer outside overnight or cut
damp, wet grass.
• The power supply cable should be checked regularly and
not damaged. If the cable is not in good condition, do not
use the trimmer.
• Only use an extension cable which is rated for outdoor use.
Keep the extension cable away from the cutting area, sharp
edges, heat, fuels and damp, wet, oily surfaces.
• Warning – To reduce the risk of electric shock, use only
with an extension cord intended for outdoor use, such as
an extension cord of cord type SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.
• Damage to unit – If you strike or become entangled with
a foreign object, stop tool immediately, unplug, check for
damage and have any damage repaired before further
operation is attempted. Do not operate with a broken
hub or spool.
• Damage to cord – Keep power cord away from rotating
line. If you damage the cord, unplug it from the power
supply before moving the tool or examining the damage.
A damaged cord must be replaced before further use.
• Disconnect tool – When not in use, when replacing line, or
prior to cleaning.
• Avoid dangerous environmental conditions – Do not use
electric tools in damp or wet locations. Don’t use the tool in
the rain. Follow all instructions in this Instruction Manual for
proper operation of your tool.
• Do not operate portable electric tools in gaseous or
explosive atmospheres. Motors in these tools normally
spark, and the sparks might ignite fumes.
• Store idle tools indoors – When not in use, tools should
be stored indoors in a dry, locked-up place out of reach
of children.
• Ground fault circuit interrupter (GFCI) protection should
be provided on the circuits or outlets to be used for the
gardening appliance. Receptacles are available having built
in GFCI protection and may be used for this measure of
protection.
• Secure extension cord using the cord retainer shown in
Figure 4.
• STAY ALERT – Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
• Maintain appliances with care – Follow instructions for
lubricating and changing accessories. Inspect extension
cords periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
• Check damaged parts – Before further use of the
appliance, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other condition
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorized service center unless otherwise indicated
elsewhere in this manual.
SAFETY WARNINGS:
Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. The table shows the correct size
to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord. If the extension
will be used outside, the cord must be suitable for outdoor
work. The letters “WA” on the cord jacket indicate that the
cord is suitable for outdoor use.
Minimum Gauge of Cord Sets
Volts Total Length of Cord in Feet
120V 25 26-50 51-100 101-150
220V 50 51-100 101-200 201-300
Ampere Rating
More Than Not more Than American Wire Gauge
0-6 18 16 16 14
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 Not Recommended
2
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S) Read, understand
and follow all instructions in the manual(s) before
attempting to assemble and operate.
WARNING! Keep out of rain and away from wet areas.
DANGER! Beware of thrown objects to bystanders.
Keep bystanders a safe distance away from the machine.
WARNING! Remove the plug from the mains immediately
if cable is damaged or cut.
Wear eye protection. For protection against injury, wear
safety goggles.
Wear protective gloves when using the machine and
handling debris.
Wear hearing protection. For protection against injury,
wear ear defenders.
SAFETY ALERT, indicates a precaution, a warning
or a danger.
3
Know Your Electric Grass Trimmer
C
D
B
A
Technical Data
Rated voltage – 120V~60Hz
Rated Power – 2.5A
Maximum Cutting diameter – 9.45"
E
F
Load Speed – 12,000/min
Diameter of Line – 0.05"
Line Length – 17'
A. Cable restraint
B. ON/OFF Switch
C. Auxiliary Handle
D. Upper Handle
E. Motor Housing
F. Safety Guard
4
Assembly Prior to Use
Before assembly, make sure that the tool is switched off and
unplugged.
1. Fitting the handle (Fig. 1)
Fig. 1
Fig. 3
Preparing the Trimmer
For Use
a) Insert the motor housing into the handle, and make
sure the handle is securely locked-in.
2. Fitting the guard (Fig. 2 & Fig. 3)
Fig. 2
a) Fix the safety guard to the trimmer head, making
sure the sides are located into the grooves on the
trimmer head.
Secure the safety guard onto the trimmer head with the
screw provided.
1. Mains supply cable strain relief (Fig. 4)
Fig. 4
In order to reduce strain on the cable inlet, form a loop and
hook the cable around the strain relief arm.
Operation
m CAUTION!: Always wear eye protection.
1. On/off switch (Fig. 5)
To switch on the trimmer, press and hold the trigger. Release
the trigger to stop.
5
15°
Fig. 5
2. Trimming
1) Use the trimmer at an angle of approximately 15-degrees
to the working area (Fig. 6).
Fig. 6
2) Slowly swing the trimmer from side to side (Fig. 7).
Fig. 7
3) Do not overload your trimmer, take small “bites”. This will
keep machine operating at high speed and will greatly
improve cutting efciency, (Fig. 8).
Fig. 8
3. Starting for the rst time and operation
You will need to exert a certain force to pull out the line when
the trimmer is used for the rst time. To do so, press on the
6
push button (Fig. 9) and pull out the line as far as the edge of
the guard hood.
Fig. 9
Fig. 11
1
Fan Housing
The line will be cut to the correct length the rst time the
cutting head is started. A short worn nylon line will result
in poor cutting performance.
To restore the correct line length, press the trimmer against
the ground while the cutting head is running.
The length of the line will then be adjusted automatically
(Fig. 10).
Fig. 10
2
Spool
3
Spool Cover
b) Replace the empty line spool with a full one. Thread the
end of the line through the holes inside of the spool
cover (3).
c) Place the spool cover on the fan, hold the fan housing
and, screw the spool cover clockwise until it sits
securely.
d) Press on the push button and pull out line as far as the
edge of the guard hood.
e) The line will be cut to the correct length the rst time
the cutting head is started.
4. To replace the spool or cutting line
m WARNING: Unplug the mains supply
cable before attempting to change the line.
a) Hold the fan housing (1) and screw the spool cover (3)
anticlockwise until it can be removed (Fig. 11).
m CAUTION! Catapulted pieces of nylon line may
cause injury
Note: The maximum recommended length of line in the spool
is 4m (157.5") per slot.
m WARNING: Pay attention to winding direction.
a) Always replace the spool with a new pre-wound spool.
7
b) Insert the end of the line through an eyelet in the
cutting head.
Important: Keep all areas of the cutting head cover and
cutting head clean. Place the cap back by pushing it rmly
into the cutting head. To ensure that the cutting head cover
is correctly tted, try to remove it without depressing the two
latches. If it is correctly tted it should not move.
Maintenance
Be sure the tool is unplugged.
1) Your grass trimmer requires no additional lubrication or
maintenance. There are no user serviceable parts in your
power tool.
2) Your trimmer line can dry out over time. To keep your line
in top condition, store spare pre-wound spools or bulk line
in plastic, sealable bag with a tablespoon of water.
3) Never use water or chemical cleaners to clean your grass
trimmer. Wipe clean with a dry cloth.
4) Plastic parts may be cleaned by using a mild soap and
damp rag.
5) Always store your grass trimmer in a dry place. Do not
allow any liquid to get inside it.
6) Keep the motor ventilation slots clean.
7) If you see some sparks ashing in the ventilation slots, this
is normal and will not damage your power tool.
8) There are no user serviceable parts in the trimmer. If a
fault is suspected return the trimmer to an authorized
dealer for repair.
IMPORTANT:
To assure product safety and reliability, repairs, maintenance
and adjustment should be performed by authorized service
centers or other qualied service organization, always using
identical replacement parts.
Bump line feed does not work
• Keep the tabs depressed and remove the spool cover
from the housing.
• Pull the cutting line until it reaches the trimming blade.
If insufcient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
• Align the tabs on the spool cover with the holes in
the housing.
• Push the cover onto the housing until it snaps securely
into place.
• If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade.
Service and Support
If your Electric Grass Trimmer requires service or maintenance,
please call 1-866-766-9563 for assistance.
Model and Serial Numbers
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of your product.
These are found on the decal afxed to the housing or guard
of your Electric Grass Trimmer. Copy these numbers into the
space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
T R J 6 0 9 E
Serial #:
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local dealer’s Authorised Service Centre.
• Before proceeding, unplug the tool.
Tool runs slowly
• Check that the spool housing can rotate freely. Carefully
clean it if necessary.
• Check that the cutting line does not protrude. If it does,
cut it off so that it just reaches the line trimming blade.
8
NOTES
9
A Two-Year Full Warranty
for residential use
in the United States and Canada
General Conditions:
Snow Joe, LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for
normal residential purposes. Snow Joe, LLC will repair any defect in material or workmanship, and repair or replace any defective part,
subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to the
original purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put
to any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any
product is rented or leased, the duration of the warranty is 90 days from the date of original purchase.
It is the owner’s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner’s manual.
Electric Products:
To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and
postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817.
Gasoline / Battery Products:
Limitations
• Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries
will be replaced free from charge during the rst 90 days. After the initial 90 days, batteries will be replaced at prorated cost to
the customer
• Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period
of two years
Exclusions
• Snow Joe brand engines are covered under this warranty. All other engines and engine accessories are covered only by the
engine manufacturer’s warranty and are not covered by this warranty
• Parts used that are not genuine Snow Joe parts are not covered by this warranty
• Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair
is not covered under this warranty
• Belts, augers, and tines are not covered under warranty – belts, augers, and tines wear out and can be purchased at
www.snowjoe.com or by calling 1-866-766-9563
Snow Joe, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
obligating Snow Joe, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
This warranty is intended to cover product defects only. Snow Joe, LLC is not liable for indirect, incidental, or consequential damages
in connection with the use of the Snow Joe Products covered by this warranty. This warranty does not cover any cost or expense
incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential
damages, so the above exclusions may not apply in all states. This warranty may give you specic legal rights in your state.
If you wish to contact Snow Joe, please direct inquiries to the:
Customer Service Department
Snow Joe Center
86 Executive Avenue
Edison, NJ 08817
Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe
Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satised with the
distributor’s service, or if you have difculty obtaining warranty information, contact your Snow Joe seller. If in the event your efforts
are unsatisfactory, please write to the Snow Joe Center at the above address.
If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.
10
Loading...