13-INCH 4-AMP ELECTRIC
GRASS TRIMMER + EDGER
Model TRJ13STE
A Division of Snow Joe®, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Before using this electric tool, carefully read and observe the
safety rules and instructions listed below. Before starting work,
make sure that you know how to stop the machine in case of
an emergency. The incorrect use of this machine could cause
serious injury. Keep these instructions in a safe place and on
hand so that they can be consulted when required.
mDANGER! The electric grass trimmer + edger should
only be used for cutting lawns and for trimming along the
borders of ower beds. Other uses of the trimmer + edger that
are not indicated in these instructions could damage the unit
or seriously injure the operator.
General Safety
1. Avoid dangerous environments – Do not use appliances
in damp or wet locations. Do not use in rain.
2. Keep children and bystanders away – Children and
other spectators, including pets, should be kept at least
50 feet (15 meters) away from the work area. When the
grass is cut, stones and debris contained in the grass can
be picked up by the trimmer + edger and dispersed into
the air. These ying projectiles can cause blindness or
other bodily injury.
3. Dress properly – Always wear suitable clothing when
using the trimmer + edger to prevent head, hand, or feet
injuries. Do not wear loose clothing or jewelry. They can
get caught in moving parts.
4. Use safety glasses – Also use safety footwear,
snug-tting clothing, protective gloves, hearing and head
protection.
5. Use the right tools – Do not use tools for any job except
that for which they are intended.
6. Avoid unintentional starting – Do not carry plugged-in
tool with nger on the trigger. Make sure the switch is o
before plugging in the tool.
7. Do not abuse the cord – Never carry the tool by the cord
or yank the cord to disconnect it from the receptacle.
Keep the cord away from heat, oil, and sharp edges.
8. Do not force the tool – It will do the job better and with
less likelihood of injury if it is used at the rate for which it
was designed.
Form No. SJ-TRJ13STE-880E-M
OPERATOR’S MANUAL
9. Do not overreach – Keep proper footing and balance at
all times.
10. Stay alert – Watch what you are doing. Use common
sense. Do not operate the trimmer + edger when you are
tired, or under the inuence of alcohol or drugs.
11. Disconnect the tool – Turn the trimmer + edger o and
disconnect the plug when: the unit is not in use; it is left
unattended; it is being examined because it is not working
correctly; the power supply cable is damaged; the blade is
being removed or changed; or when the trimmer is being
moved from one place to another.
12. Store idle tools indoors – When not in use, tools should
be stored indoors in a dry and high or locked-up place out
of the reach of children.
13. Maintain tools with care – Keep cutting edges sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and changing
accessories. Inspect the trimmer + edger periodically and
replace if damaged. Repair the trimmer + edger only at an
authorized service facility. Keep handles dry, clean, and
free from oil and grease.
14. Checked for damaged parts – Before continuing to
use the trimmer + edger, a guard or other part that is
damaged should be carefully checked to determine that
it will operate properly and perform its intended function.
Check for the alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other
condition that may aect the tool’s operation. A guard or
other part that is damaged should be properly repaired or
replaced by an authorized service center unless indicated
elsewhere in this manual.
mCAUTION! The safety guard is critical to the safety of
the operator and the safety of people standing within a safe
distance of the trimmer + edger. The safety guard keeps the
unit in good working order and must always be in place during
operation. Failure to have the guard in place during operation
is dangerous and will void the warranty.
15. Keep away from the cutting line – It can seriously injure
the skin.
16. Do not try to stop the cutting device with your hands –
Always let it come to a stop by itself.
17. Inspect electrical cables – The insulation of the power
cord should be perfectly intact. If the power cord is
damaged or shows any signs of cracks, do not use the
trimmer. Contact your authorized Snow Joe® + Sun Joe®
dealer or call the Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563).
© 2015 by Snow Joe®, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
mCAUTION! The trimmer line spool will continue to rotate
after turning the trimmer OFF. Wait until the trimmer line spool
has completely stopped before making contact.
• Only use the same type of line originally provided with the
tool.
• Do not use the unit to cut grass that is not in contact with
the ground.
• Do not switch the string trimmer + edger ON in enclosed or
poorly ventilated spaces or in the presence of ammable
and/or explosive substances such as liquids, gases, and
powders.
• The user of the trimmer + edger is responsible for any
damage sustained by third parties that has been caused by
the grass trimmer within the working area.
• Only cut during broad daylight or with adequate articial
light.
• Do not cross roads or gravel paths while the unit is still
running.
• When the trimmer + edger is not in use, store it in a dry
place and out of the reach of children.
• The trimmer + edger must be operated in a vertical position,
perpendicular to the ground.
• Check regularly that all screws are properly secured.
Electrical Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
this electric grass trimmer. Receptacles are available
having built-in GFCI protection and may be used for this
measure of safety.
2. Make sure that the mains voltage matches that listed on
the unit's rating label. Using the improper voltage can
damage the motor and injure the user.
3. To reduce the risk of electric shock, this appliance has a
polarized plug (i.e. one blade is wider than the other). Use
this appliance only with a polarized UL-, CSA- or ETL-
listed extension cord recommended for outdoor,
all-weather use, such as the Snow Joe® + Sun Joe®
Power Joe SJTW-A 14-gauge 50-foot extension cord with
lighted end (Model PJEXT50-B). Visit snowjoe.com to
purchase this extension cord online or, to order by phone,
call 1-866-SNOWJOE (1-866-766-9563).
The appliance plug will t into a polarized extension
cord only one way. If the appliance plug does not t
fully into the extension cord, reverse the plug. If the plug
still does not t, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. The extension cord plug will t into
the polarized wall outlet only one way. If the plug does
not t fully into the wall outlet, reverse the plug. If the plug
still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug,
extension cord receptacle, or extension cord plug
in any way.
4. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current your product
will draw. For lengths less than 50 ft (15 m), a No.16 AWG
(or greater) extension cord should be used. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating.
m WARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric grass trimmer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA-, or ETL-rated extension cord
for outdoor, all-weather use, such as the Snow Joe
Sun Joe
extension cord with lighted end (Model PJEXT50-B).
Visit snowjoe.com to purchase this extension cord
online or, to order by phone, call 1-866-SNOWJOE
(1-866-766-9563).
• Do not use an extension cord over 150 ft (46 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
Cord Length:
Min. Wire Gauge
(A.W.G.):
5. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
Cord set Appliance cord
®
Power Joe SJTW-A 14-gauge 50-foot
EXTENSION CORD CHART
50 ft (15 m) 100 ft (30 m)
16 16
Table 1. Method of Securing Extension Cord
(A) Tie cord as shown
(B) Connect plug and receptacle
150 ft (46 m)
14
®
+
2
Additional Electrical Safety Rules
• The voltage must correspond to the one marked on the
technical data plate (120 V~60 Hz). Do not use other
sources of power.
• The power line should have a circuit breaker no lower than
10 A. Consult an electrician if this is not the case.
• Never pass the grass trimmer + edger over the extension
cord when the grass trimmer + edger is in use as this could
cut the cord. Make sure you know where the cord is at all
times.
• Use the special cord restraint hook to connect the
extension cord.
• Never use the tool when it is raining or when excessively
moist and humid conditions are present. Do not
cut damp grass or leave the tool outside overnight.
• The power supply cable should be checked regularly to
make sure it is perfectly intact without any signs of wear or
damage. If the cable is not in good condition, do not use
the unit.
• Only use an extension cable that is rated for outdoor use.
Keep the extension cord away from the cutting area, sharp
edges, heat, fuels, damp areas, and oily surfaces.
• Damage to unit – If the trimmer + edger strikes a foreign
object or becomes entangled with it, stop the tool
immediately. Unplug it, check for damage, and have any
damage repaired before proceeding with operation. Do
not operate the tool with a broken hub or spool. Contact
your authorized Snow Joe® + Sun Joe® dealer or call
the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
• Damage to cord – Keep power cord away from the rotating
line. If you damage the cord, unplug it from the power
supply before moving the tool or examining the damage.
A damaged cord must be replaced before further use.
• Do not operate portable electric tools in gaseous or
explosive atmospheres – Motors in these tools normally
spark, and the sparks might ignite fumes.
• Maintain appliances with care – Follow instructions for
lubricating and changing accessories. Inspect extension
cords periodically and replace if damaged. Keep handles
dry, clean, and free from oil and grease.
Double-Insulated Appliances
In a double-insulated appliance, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a doubleinsulated appliance requires extreme care and knowledge
of the system, and should be performed only by qualied
service personnel at an authorized Snow Joe® + Sun Joe®
dealer. Replacement parts for a double-insulated appliance
must be identical to the parts they replace. A double-insulated
appliance is marked with the words “Double Insulation” or
“Double Insulated.” The symbol (square within a square)
may also be marked on the appliance.
DOUBLE-INSULATED: GROUNDING NOT
REQUIRED. WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
This electric grass trimmer + edger is double-insulated,
eliminating the need for a separate grounding system. Use
only identical replacement parts. Read the instructions before
servicing double-insulated appliances. Use this grass trimmer
+ edger only as described in this manual.
mWARNING! Some dust and debris created by the
use of the tool could contain chemicals known to the State
of California to cause cancer and birth defects or other
reproductive harm. Some examples of these chemicals are:
• Chemicals in fertilizers
• Compounds in insecticides, herbicides, and pesticides
• Arsenic and chromium from chemically treated lumber
Your risk from exposure to these chemicals varies, and
depends on how often you do this type of work. To reduce
your exposure, work in a well-ventilated area and with
approved safety equipment, such as dust masks that are
specially designed to lter out microscopic particles.
mWARNING! California Proposition 65:
This product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive
harm.
3
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
Keep bystanders and children
a safe distance away.
SAFETY ALERT – Indicates
a precaution, a warning, or
a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Wear protective gloves when
using the machine and handling
debris.
Immediately remove the plug from
the mains if the power cable is
damaged, frayed, or entangled.
Always keep the power cable away
from heat, oil and sharp edges.
WARNING! Do not expose the unit
to rain or wet conditions.
Beware of ying objects and
debris.
WARNING! Turn the machine OFF
and disconnect it from the power
supply before inspecting, cleaning,
changing accessories, or conducting
any other maintenance task.
DOUBLE INSULATION –
When servicing, use only identical
replacement parts.
DANGER! Beware of thrown objects to bystanders. Keep bystanders at least
15 m (50 ft) away from the machine.
4
Know Your Electric Grass Trimmer + Edger
Read the owner’s manual and safety instructions carefully before operating the electric grass trimmer + edger. Compare the
illustration below to your electric grass trimmer + edger in order to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
1. Rear handle
2. Safety lock button
3. ON/OFF trigger switch
4. Extension cord restraint hook
5. Power plug
6. Adjustable auxiliary handle
7. Handle knob
8. Edging coupler
9. Telescoping locking coupler
10. Telescoping tube
11. Edger guide + ower guard
12. Safety guard
13. Nylon cutting line
6
7
1
2
8
9
3
4
5
11
13
Technical Data
Rated Voltage 120 V ~ 60 Hz
Power 4 amp
Cutting Swath 13 in. (33 cm)
Spool Length 16.4 ft. (5 m)
10
12
No Load Speed 7,800 rpm
Spool Advance Auto-feed
Line Diameter 0.063 in. (1.6 mm)
Weight 5.07 lbs. (2.3 kg)
5
Unpacking
Carton Contents
• Electric grass trimmer + edger
• Safety guard
• Edger guide + ower guard
• Manual with registration card
1. Carefully remove the electric grass trimmer + edger and
check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use the electric grass
trimmer + edger. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations or save the packaging
for long-term product storage.
IMPORTANT! The equipment and packaging material are not
toys. Do not let children play with plastic bags, foils, or small
parts. These items can be swallowed and pose a suocation
risk!
2. Place the safety guard in the direction of the arrow shown
to align it with the screw hole in the motor housing
(Fig. 2).
Fig. 2
Safety guard
NOTE: Never use the tool unless the safety guard is properly
tted.
3. Firmly press the safety guard into place and secure it to
the trimmer head with the screw provided (Fig. 3).
Fig. 3
Assembly
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
Fitting the Safety Guard
mWARNING! The guard must be properly installed. The
guard provides the operator and other bystanders with some
protection from thrown objects.
1. Using a screwdriver, remove the small screw that is
secured in the small hole in the motor housing (Fig. 1).
Fig. 1
Small hole
Screw
Screw
Fitting the Edger Guide + Flower Guard
1. Lightly spread the edger guide + ower guard by hand
while approaching the motor housing (Fig. 4).
Fig. 4
Edger guide + ower guard
6
2. While lightly spreading the edger guide + ower guard, t
the curved ends into the small holes on both sides of the
motor housing, and release (Figs. 5 & 6).
Fig. 5
Operation
Auxiliary Handle Adjustment
NOTE: For maximum comfort and control, adjust the auxiliary
handle to t your height. Shorter users adjust the auxiliary
handle to a lower position (away from your body). Taller users
adjust the auxiliary handle to an upper position (towards to
your body). Make sure your forearm is straight when using the
machine.
1. Loosen the auxiliary handle by turning the handle knob
counterclockwise (Fig. 8).
Curved ends of
Small hole on the
housing
RIGHT SIDE VIEW
edger guide +
ower guard
Fig. 6
Curved ends of
edger guide +
ower guard
LEFT SIDE VIEW
3. The edger guide + ower guard can be ipped up so it
stores against the motor housing for convenient storage,
when not in use (Fig. 7).
Small hole on the
housing
Fig. 8
Handle knob
2. Adjust the auxiliary handle to a comfortable working
position (Fig. 9).
Fig. 9
Fig. 7
Auxiliary handle
7
3. Turn the handle knob clockwise to tighten and secure the
auxiliary handle in place (Fig. 10).
3. Extend the telescoping tube to a comfortable height
(Fig. 12).
Fig. 10
Auxiliary handle
Handle knob
Height Adjustment
The telescoping tube can be extended or shortened for ease of
use.
1. Disconnect the grass trimmer + edger from the power
supply.
2. Unlock the telescoping tube by turning the telescoping
locking coupler clockwise (Fig. 11).
Fig. 12
4. Lock the telescoping tube in position by turning the
telescoping locking coupler counter-clockwise.
Securing the Extension Cord
1. Make a loop with the extension cord.
2. Insert the loop through the opening in the back of the
upper handle and secure the loop onto the extension cord
restraint hook (Fig. 13).
Fig. 13
Fig. 11
Telescoping
locking
coupler
Opening
Extension cord
restraint hook
8
3. Connect the extension cord to the power plug (Fig. 14).
Fig. 14
Power plug
Starting + Stopping
Before you start the unit, make sure the trimmer is not
contacting any object.
1. To turn the grass trimmer + edger ON, press and hold the
safety lock button with your thumb, then squeeze the ON/
OFF trigger switch with your ngers. Once the machine
powers on, you can release the safety button and proceed
with operation (Fig. 15).
Fig. 15
Trimming
• Wear non-slip gloves for maximum grip and protection.
• For the best cutting action against walls, fences, and in high
grass, move the grass trimmer slowly so grass is cut with
the tip of the high speed nylon line.
• Avoid dragging the grass trimmer and string spool hub in
contact with the ground.
• Trim only when grass and weeds are dry.
NOTE: As the weather becomes cooler, the tendency for the
nylon line to break becomes greater. DO NOT USE WHEN
TEMPERATURE IS BELOW 50ºF (10ºC).
• Cut tall grass from top down. This will prevent grass from
wrapping around the shaft housing and string head which
may cause damage from overheating.
• If grass becomes wrapped around the string head:
– Stop the trimmer.
– Unplug the string trimmer.
– Remove the grass.
• Hold the grass trimmer with your right hand on the rear
handle and your left hand on the front auxiliary handle. The
trimmer + edger should be held at a comfortable position
with the rear handle about hip height.
mWARNING! Always hold the trimmer away from
body. Any contact with the grass trimmer cutting head while
operating can result in serious personal injury.
• The life of your nylon line is dependent upon following
instructions for proper use, as well as what is being cut, and
where the cutting is being done.
Safety lock
button
ON/OFF trigger
switch
2. To switch OFF, release the ON/OFF trigger switch (Fig. 15).
mWARNING! Remove stones, loose pieces of wood, and
other objects from the cutting area. The string continues to
rotate for a few seconds after switching o the trimmer. Let the
motor come to a complete stop before resuming operation. Do
not rapidly switch the trimmer o and on.
mCAUTION! Always wear eye protection.
9
1. Hold the trimmer at an angle of approximately 10 – 30
degrees to the work area (Fig. 16).
Fig. 16
10° – 30°
2. Slowly swing the trimmer from side to side (Fig. 17).
Fig. 17
Edging
1. To convert for maintenance edging, turn OFF and unplug
the tool.
2. To use the edger guide + ower guard, ip it down from its
stored position (Fig. 19).
Fig. 19
Edger guide +
ower guard
3. Do not overload your trimmer; instead, take small “bites”
of grass, working from the top to the bottom. This will
keep the machine operating at high speed and will greatly
improve its cutting eciency (Fig. 18).
Fig. 18
3. Pull up edging coupler and turn the rear handle
counterclockwise and release (Fig. 20). The tool is locked
in edger mode.
Fig. 20
Rear
handle
Pull up edging
coupler to
rotate
10
4. Rotate the whole unit 180 degrees. The tool is now ready
to be used in edger mode (Fig. 21).
Fig. 21
Advancing Strings
NOTE: Your trimmer uses 0.063 in. (1.6 mm) diameter nylon
line to cut grass and weed quickly and easily. In time, the
tip of the nylon line will become worn and the auto-feed
mechanism will automatically feed and trim a fresh length of
line. The cutting line will wear faster if the cutting is done along
sidewalks or other abrasive surfaces or heavier weeds are
being cut.
The trimmer + edger is equipped with an auto-feed head.
Bumping the head to try to advance the string will damage
trimmer.
1. With the unit running, release the ON/OFF switch trigger.
2. Wait two seconds, and press the ON/OFF switch trigger.
NOTE: The strings will extend approximately 1/4 in. with each
stop and start of the switch trigger until the strings reach the
length of the safety guard.
3. Resume the trimming + edging.
5. Use the edge of the guard as a guide when cutting near
fences and walls (Fig. 22).
Fig. 22
6. Move the edger in a backwards direction when trimming
around edges to avoid damage.
mWARNING! Do not trim near electrical wires.
mWARNING! Do not operate the grass trimmer + edger
in a tree, on a ladder, or on a scaold; this is extremely
dangerous.
mWARNING! Do not bump the unit on ground in attempt
to feed line or for any other purpose.
Maintenance
mWARNING! Make sure to unplug your electric grass
trimmer + edger before inspecting its parts.
mWARNING! Always wear protective gloves during
maintenance tasks. Do not carry out maintenance when the
motor is running or hot.
• Your trimmer line can dry out over time. To keep your line in
top condition, store spare pre-wound spools or bulk line in
a plastic resealable bag with a tablespoon of water.
• Never use water or chemical cleaners to clean your grass
trimmer + edger. Wipe it clean with a dry cloth.
• Plastic parts may be cleaned by using mild soap and a
damp rag.
• Always store your grass trimmer + edger in a dry place. Do
not allow any liquid to get inside it.
• Keep the motor ventilation slots clean.
• If you see some sparks ashing in the ventilation slots, this
is normal and will not damage your power tool.
IMPORTANT! To ensure product safety and reliability, repairs,
maintenance, and adjustments to this power tool should be
performed only with identical replacement parts. Contact your
authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe®
+ Sun Joe® customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
11
Replacing the Spool + Clearing Jams
and Tangled Lines
mWARNING! Unplug the extension cord from the main
power plug before changing the trimmer line.
1. Press together both release tabs on the line spool cover
and remove the cover by pulling it straight o (Fig. 23).
Fig. 23
Fig. 25
Sleeve
Spool
Spool cover
Tab
2. Lift and remove the sleeve and spool out of the hub
(Fig. 24) and clean out any dirt or grass residue.
Fig. 24
Spool
Sleeve
Slot
5. Insert each line end through its respective slot on each
side of the hub and gently press the spool down (Fig. 26).
Fig. 26
Hub
Slot
6. Reinstall the spool cover by depressing the release tabs
into their slots in the hub, and push down until the spool
cover clicks into place.
7. Connect the tool to a power source and turn the tool
on. In a few seconds, you will hear the line being cut
automatically to the proper length.
3. In case of jams or tangled line, unwrap about 6 inches
(15 cm) of line to ensure that it's not damaged.
4. If it appears undamaged, rewind it and insert each line end
through the two slots on each side of the sleeve. Place the
sleeve over the spool (Fig. 25).
Winding the Line
NOTE: A dual-line factory wound spool (model TRJ13STERS)
is available for easy spool replacement on the TRJ13STE
electric grass trimmer + edger. Visit snowjoe.com to purchase
this accessory online. Should you wish to wind the line
yourself, the instructions are provided below. Self-winding,
however, is NOT recommended because if the line is not
wound properly it can cause the trimmer’s auto feed system
to malfunction. For this reason, users are strongly urged to
purchase the pre-wound spool.
12
1. Unplug the grass trimmer.
2. To remove the spool from the trimmer hub, follow steps
1 and 2 from the section "Replacing the Spool + Clearing
Jams and Tangled Lines" beginning on page 12.
3. Find the middle of a new piece of 0.063 inch nylon line (up
to 16 feet total with 8 feet on both ends), and insert the
middle of the line into the groove in the center of the spool
(Fig. 27).
Fig. 27
Groove
mWARNING! Pay attention to the winding direction.
NOTE: Always replace the spool with a new pre-wound spool.
Visit snowjoe.com to purchase the pre-wound spool
(model TRJ13STERS) for this electric trimmer + edger.
IMPORTANT: Keep all areas of the cutting head and cutting
head cover clean. Place the cap back by pushing it rmly
onto the cutting head. To ensure that the cutting head cover
is correctly tted, try to remove it without depressing the two
latches. If it is correctly tted, it should not move.
Storage
Follow these recommendations for storing the trimmer.
• Clean the trimmer + edger thoroughly before storing.
• Store the trimmer + edger in a stable and safe position out
of the reach of children. Keep the trimmer in a dry place
where the temperature is not too hot or too cold.
• When storing the trimmer + edger, do not rest it against the
oor. Hang it by the upper handgrip so that the guard does
not touch anything. If the guard rests against a surface, its
shape and dimensions could be permanently altered, and
could render the machine unsafe to use.
4. Wind both ends into the grooves using slight tension and
following the direction of the arrows (Fig. 28).
Fig. 28
5. Re-install the spool as instructed in steps 4 to 7 of
"Replacing the Spool + Clearing Jams and Tangled Lines".
mCAUTION! Catapulted pieces of nylon line may cause
injury.
NOTE: The maximum recommended length of line in the spool
is 16.4 ft (5 m), with 8 ft (2.5 m) per slot.
Service and Support
If your Sun Joe® Trimmer Joe TRJ13STE electric grass trimmer
+ edger requires service or maintenance, please call the
Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
Model and Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
T R J 1 3 S T E
Serial #:
13
Troubleshooting
Problems Possible Cause Possible Solution
The motor does not
run or the tool runs
slowly.
Auto line feed does
not work.
Line fails to cut o.
• Power failure/unit not plugged
into a working receptacle.
• Spool housing cannot rotate freely.
• Cutting line does not protrude.
• Trimming blade bound with
accumulated grass.
• Auto feed out of line.
• Spool bound up.
• Auto feed is dirty.
• Spool line twisted when relled.
• Not enough line is exposed.
• Line cutter in guard is covered,
damaged, or missing.
• Line extends past guard.
• Check to make sure the unit is plugged into a working
outlet. Make sure the extension cord is not damaged.
• Remove the spool and clean the slots; carefully remove
any grass and weeds or other debris.
• Cut the spool line o so that it just reaches the line
trimming blade.
• Take the trimmer to an authorized service center if the
trimmer does not start after completing these checks.
• Stop the machine and clean the trimming blade.
• Install a new spool of cutting line.
• Clean the auto feed.
• Remove the spool cover and pull the cutting line until it
reaches the trimming blade.
• Contact your authorized Snow Joe® + Sun Joe® dealer
or call Snow Joe
1-866-SNOWJOE (1-866-766-9563).
• Rewind or trim line to line cutter.
®
+ Sun Joe® customer service center at
14
Accessories
mWARNING! ALWAYS use only authorized Snow Joe
replacement parts or accessories that are not intended for use with this electric grass trimmer + edger. Contact Snow Joe® +
Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your electric grass trimmer +
edger. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
®
+ Sun Joe® replacement parts and accessories. NEVER use
ModelAccessories Item
1
Dual-line pre-wound spool for TRJ13STE
2
Snow Joe® + Sun Joe® Power Joe SJTW-A
14-gauge 50-foot extension cord with
lighted end
TRJ13STERS
PJEXT50-B
3
Snow Joe® + Sun Joe® universal wall bracket
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563).
SJWB
15
NOTES
16
NOTES
17
NOTES
18
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience
as pleasant as possible. Unfortunately, there are times when a product does not work or breaks under normal
operating conditions. We think it’s important that you know what you can expect from us. That’s why we created
the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product
does not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or
by sending you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in
action cutting, sawing, mowing, washing and…?
GENERAL CONDITIONS:
Snow Joe® + Sun Joe® operating under Snow Joe®, LLC warrants
this new product to the original purchaser for two years against
defects in material or workmanship when used for normal
residential purposes. If a replacement part or product is needed,
it will be sent free of charge to the original purchaser except as
noted below.
The duration of this warranty applies only if the product is put
to personal use around the household. If the product is put to
any business, commercial or industrial use or is rented or leased,
then the duration of this warranty is 90 days from the date of
original purchase. It is the owner’s responsibility to correctly
perform all maintenance and minor adjustments explained in
the owner’s manual.
HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:
To obtain a replacement part or product, please visit
snowjoe.com/help or email us at help@snowjoe.com for
instructions. Please be sure to register your unit beforehand to
speed up this process. Certain products may require a serial
number, typically found on the decal axed to the housing
or guard of your product. All products require a valid proof
of purchase.
EXCLUSIONS:
• Wearing parts like belts, augers, chains and tines are
not covered under this warranty. Wearing parts can be
purchased at snowjoe.com or by calling 1-866-SNOWJOE
(1-866-766-9563).
• Batteries are covered in full for 90-days from the date of
purchase.
Snow Joe® + Sun Joe® may from time to time change the design
of its products. Nothing contained in this warranty shall be
construed as obligating Snow Joe® + Sun Joe® to incorporate
such design changes into previously manufactured products, nor
shall such changes be construed as an admission that previous
designs were defective.
This warranty is intended to cover product defects only.
Snow Joe®, LLC is not liable for indirect, incidental or
consequential damages in connection with the use or misuse of
the Snow Joe® + Sun Joe® products covered by this warranty.
This warranty does not cover any cost or expense incurred
by the purchaser in providing substitute equipment or service
during reasonable periods of malfunction or non-use of this
product while waiting for a replacement part or unit under this
warranty. Some states do not allow exclusions of incidental or
consequential damages so the above exclusions may not apply
in all states. This warranty may give you specic legal rights in
your state.
HOW TO REACH US:
We’re here to help Monday through Friday from 9AM to 6PM EST.
You can reach us at 1-866-SNOWJOE (1-866-766-9563), online
at snowjoe.com, via email at help@snowjoe.com or tweet us
@snowjoe.
EXPORTS:
Customers who have purchased Snow Joe® + Sun Joe®
products exported from the United States and Canada should
contact their Snow Joe® + Sun Joe® distributor (dealer) to obtain
information applicable to your country, province or state. If for
any reason, you are not satised with the distributor’s service,
or if you have diculty obtaining warranty information, contact
your Snow Joe® + Sun Joe® seller. If in the event your eorts are
unsatisfactory, please reach out to us directly.
19
snowjoe.com
Loading...