Page 1
OPERATOR’S MANUAL
A Division of Snow Joe®, LLC
R
CORDLESS GO-ANYWHERE PORTABLE
PRESSURE WASHER – CORE TOOL
1160 PSI MAX | 1 GPM MAX | 40 V | PRESSURE SELECT
Model SPX6001C-CT Form No. SJ-SP6001C-CT-880E-M
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
mWARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
• Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with
the controls.
• Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
• Use the right product – Do not use this machine for any
job except that for which it is intended.
• Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
• mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
• Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are
tired, or under the inuence of alcohol or drugs.
• Do not overreach – Keep proper footing and balance at
all times.
• Avoid unintentional starting – Do not carry a machine with
power with your nger on the trigger. Make sure the switch
is o before insert the battery.
• Remove the battery – Remove the battery from the
pressure washer when it is not in use, before servicing it,
when changing accessories, and when performing any
other maintenance task.
• Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
• Check the water temperature – This pressure washer is
not meant to pump hot water. NEVER connect it to a hot
water supply or pour hot water into the bucket as it will
signicantly reduce the life of the pump.
• Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be
seriously damaged.
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the
manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
• Risk of explosion – Do not spray ammable liquids.
• Keep children away – This cordless high-pressure washer
must not be used by children or untrained personnel. Close
supervision is necessary when a product is used near
children.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the
manufacturer.
© 2018 by Snow Joe®, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
Page 2
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its
power source by removing the battery.
mWARNING! Use only approved replacement batteries;
other batteries may damage the pressure washer and cause it
to malfunction, which can lead to serious personal injury.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by the
manufacturer.
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you nd any, do not start up your machine and contact your
distributor.
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
• Check for damaged parts – Do not use the appliance if
any important parts of the appliance are damaged (e.g.
safety devices, high-pressure hoses, trigger gun).
• This cordless high-pressure power washer must not be
used at temperatures below 32ºF (0°C).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water.)
Battery & Charger
Safety Instructions
NOTE: This unit is a core tool. The battery and the charger
are not included. They must be purchased separately. Model
SPX6001C-CT is compatible with the following batteries
(models iBAT40, iBAT40XR and iBAT40XRP) and chargers
(models iCHRG40 and iCHRG40-DPC). See page 19 for more
information.
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to be able to assemble the
best possible battery packs.
Despite all the safety precautions, caution must always be
exercised when handling batteries. The following points must
be obeyed at all times to ensure safe use. Safe use can only
be guaranteed if undamaged cells are used. Incorrect handling
of the battery pack can cause cell damage.
IMPORTANT! Analyses conrm that incorrect use and poor
care of high-performance batteries are the main factors
responsible for personal and/or product damage.
mCAUTION! To reduce the risk of injury, only charge
your iONMAX 40 V System lithium-iON battery pack in the
compatible iONMAX charger (model iCHRG40). Other types of
chargers present risk of re, personal injury and damage. Do
not wire a battery pack to a power supply plug or car cigarette
lighter. Such misuse will permanently disable or damage the
battery pack.
• Avoid dangerous environments – Do not charge the
battery pack in rain, snow or in damp or wet locations.
Do not use the battery pack or charger in the presence of
explosive atmospheres (gaseous fumes, dust or ammable
materials) because sparks may be generated when inserting
or removing the battery pack, which could lead to a re.
• Charge in a well-ventilated area – Do not block the
charger vents. Keep them clear to allow for proper
ventilation. Do not allow smoking or open ames near a
charging battery pack. Vented gases may explode.
NOTE: The safe temperature range for the battery is -4°F
(-20°C) to 113°F (45°C). Do not charge the battery outside
in freezing weather; charge it at room temperature.
• Maintain charger cord – When unplugging the charger, pull
the plug, not the cord, from the receptacle to reduce the
risk of damage to the electrical plug and cord. Never carry
the charger by its cord or yank it by the cord to disconnect
it from the receptacle. Keep the cord away from heat, oil
and sharp edges. Make sure the cord will not be stepped
on, tripped over or subjected to damage or stress when the
charger is in use. Do not use the charger with a damaged
cord or plug. Replace a damaged charger immediately.
• Do not use an extension cord unless it is absolutely
necessary – Using the wrong, damaged or improperly
wired extension cord poses a risk of re and electric shock.
If an extension cord must be used, plug the charger into a
properly wired 16 gauge or larger extension cord with the
female plug matching the male plug on the charger. Make
sure that the extension cord is in good electrical condition.
• Charger iCHRG40 is rated for 120 volt AC only – The
charger must be plugged into an appropriate receptacle.
• Use only recommended attachments – Use of an
attachment not recommended or sold by the battery
charger or battery pack manufacturer may result in risk of
re, electric shock or personal injury.
• Unplug charger when not in use – Make sure to remove
battery packs from unplugged chargers.
mWARNING! To reduce the risk of electric shock,
always unplug the charger before performing any cleaning
or maintenance. Do not allow water to ow into the charger.
Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock
hazards.
2
Page 3
• Do not burn or incinerate battery packs – Battery packs
may explode, causing personal injury or damage. Toxic
fumes and materials are created when battery packs are
burned.
• Do not crush, drop or damage battery packs – Do not
use the battery pack or charger if they have sustained a
sharp blow, been dropped, run over or have been damaged
in any way (i.e. pierced with a nail, hit with a hammer,
stepped on, etc.).
• Do not disassemble – Incorrect reassembly may pose
a serious risk of electric shock, re or exposure to toxic
battery chemicals. If the battery or charger are damaged,
contact an authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563) for assistance.
• Battery chemicals cause serious burns – Never let a
damaged battery pack contact the skin, eyes or mouth.
If a damaged battery pack leaks battery chemicals, use
rubber or neoprene gloves to safely dispose of it. If skin
is exposed to battery uids, wash the aected area with
soap and water and rinse with vinegar. If eyes are exposed
to battery chemicals, immediately ush with water for 20
minutes and seek medical attention. Remove and dispose
of contaminated clothing.
• Do not short circuit – A battery pack will short circuit if
a metal object makes a connection between the positive
and negative contacts on the battery pack. Do not place a
battery pack near anything that may cause a short circuit,
such as paper clips, coins, keys, screws, nails and other
metallic objects. A short-circuited battery pack poses a risk
of re and severe personal injury.
• Store your battery pack and charger in a cool, dry
place – Do not store the battery pack or charger where
temperatures may exceed 104ºF (40ºC), such as in direct
sunlight or inside a vehicle or metal building during the
summer.
Information about the battery
NOTE: Model SPX6001-CT is compatible with the following
battery packs (sold separately): iBAT40, iBAT40XR or
iBAT40XRP.
1. The battery packs ship partially charged, and must be
charged completely before you use the tool for the rst
time.
2. For optimum battery performance, avoid low discharge
cycles by charging the battery pack frequently.
3. Store the battery pack in a cool place, ideally at 59°F
(15°C) and charged to at least 40%.
4. Lithium-ion batteries are subject to a natural aging
process. The battery pack must be replaced at the latest
when its capacity falls to just 80% of its capacity when
new. Weakened cells in an aged battery pack are no
longer capable of meeting the high power requirements
needed for the proper operation of your pressure washer,
and therefore pose a safety risk.
5. Do not throw battery packs into an open re as this poses
a risk of explosion.
6. Do not ignite the battery pack or expose it to re.
7. Do not exhaustively discharge batteries. Exhaustive
discharge will damage the battery cells. The most
common cause of exhaustive discharge is lengthy storage
or non-use of partially discharged batteries. Stop working
as soon as the performance of the battery falls noticeably
or the electronic protection system triggers. Place the
battery pack in storage only after it has been fully charged.
8. Protect batteries and the tool from overloads. Overloads
will quickly result in overheating and cell damage inside
the battery housing even if this overheating is not
apparent externally.
9. Avoid damage and shocks. Immediately replace batteries
that have been dropped from a height of more than 3 feet
(1 m) or those that have been exposed to violent shocks,
even if the housing of the battery pack appears to be
undamaged. The battery cells inside the battery may have
suered serious damage. In such instances, please read
the waste disposal information for proper battery disposal.
10. If the battery pack suers overloading and overheating,
the integrated protective cuto will switch o the
equipment for safety reasons.
IMPORTANT! Do not press the ON/OFF switch any more
if the protective cut-o has been activated. This may
damage the battery pack.
11. Use only original battery packs. The use of other batteries
poses a re risk and may result in injuries or an explosion.
Information about the charger and the
charging process
1. Please check the data marked on the rating plate of the
battery charger (sold separately). Be sure to connect the
battery charger to a power supply with the voltage marked
on the rating plate. Never connect it to a dierent mains
voltage.
2. Protect the battery charger and its cord from damage.
Keep the charger and its cord away from heat, oil and
sharp edges. Have damaged cords repaired without delay
by a qualied technician at an authorized Snow Joe® +
Sun Joe® dealer or call the Snow Joe® + Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563).
3. Electrical plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
grounded appliances. Unmodied plugs and matching
outlets will reduce the risk of electric shock.
4. Keep the battery charger, battery pack(s) and the cordless
tool out of the reach of children.
5. Do not use the supplied battery charger to charge other
cordless tools.
6. During periods of heavy use, the battery pack will become
warm. Allow the battery pack to cool to room temperature
before inserting it into the charger to recharge.
3
Page 4
7. Do not overcharge batteries. Do not exceed the maximum
charging times. These charging times only apply to
discharged batteries. Frequent insertion of a charged or
partially charged battery pack will result in overcharging
and cell damage. Do not leave batteries in the charger for
days on end.
8. Never use or charge batteries if you suspect that it has
been more than 12 months since the last time they were
charged. There is a high probability that the battery pack
has already suered dangerous damage (exhaustive
discharge).
9. Charging batteries at a temperature below 50°F (10°C) will
cause chemical damage to the cells and may cause a re.
10. Do not use batteries that have been exposed to heat
during the charging process, as the battery cells may have
suered dangerous damage.
11. Do not use batteries that have suered curvature or
deformation during the charging process or those that
exhibit other atypical symptoms (gassing, hissing,
cracking, etc.).
12. Never fully discharge the battery pack (maximum
recommended depth of discharge is 80%). A complete
discharge of the battery pack will lead to premature aging
of the battery cells.
Protectionfromenvironmentalinuences
1. Wear suitable work clothes. Wear safety goggles.
2. Protect your cordless tool and the battery charger from
moisture and rain. Moisture and rain can cause dangerous
cell damage.
3. Do not use the cordless tool or the battery charger near
vapors and ammable liquids.
4. Use the battery charger and cordless tools only in dry
conditions and at an ambient temperature of 50-104°F
(10-40°C).
5. Do not keep the battery charger in places where the
temperature is liable to reach over 104°F (40°C). In
particular, do not leave the battery charger in a car that is
parked in the sunshine.
6. Protect batteries from overheating. Overloads,
overcharging and exposure to direct sunlight will result
in overheating and cell damage. Never charge or work
with batteries that have been overheated – replace them
immediately, if possible.
7. Store the charger and your cordless tool only in dry
locations with an ambient temperature of 50-104°F
(10-40°C). Store your lithium-ion battery pack in a cool,
dry place at a temperature of 50-68°F (10-20°C). Protect
the battery pack, charger and cordless tool from humidity
and direct sunlight. Only place fully charged batteries in
storage (charged to at least 40%).
8. Prevent the lithium-ion battery pack from freezing. Battery
packs that were stored below 32°F (0°C) for more than
60 minutes must be discarded.
9. When handling batteries, be wary of electrostatic charge.
Electrostatic discharges can damage the electronic
protection system and the battery cells. Avoid electrostatic
charging and never touch the battery poles.
Risk of Explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause
physical injuries to the operator and irreversible damage to
the machine.
Additional Safety Instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
• Do not spray electrical apparatus and wiring.
• ARCING PARTS – Keep the motor at least 20 ft (6 m) away
from explosive vapors.
• mCAUTION! Gun kicks back. Hold trigger with both
hands.
Product Description
Purpose
• This cordless high-pressure power washer is intended
for residential use to clean vehicles, machines, buildings,
facades, etc.
Areas of Application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
• The machine consists of an assembly with a pump, which
is encased in a shock-absorbing housing. To provide the
operator with an optimal working position, the machine is
equipped with a spray wand and a non-slip handle grip,
whose shape and conguration comply with applicable
regulations.
• Do not cover or modify the spray wand or the spray nozzles
in any way.
• The cordless high-pressure washer is designed to be used
with cold or lukewarm water; higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as these could impair operation and
shorten the life of the machine.
4
Page 5
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
WARNING! Do not expose the unit
to rain or wet conditions. Keep dry.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
To reduce the risk of injury, user
must keep all bystanders at least
49 ft (15 m) away.
Wear safety gloves during
use to protect hands.
Store indoors. Never store the
pressure washer outdoors.
If the pump freezes, permanent
damage may result.
Sound power level is 96 dB(A).
Machine not suitable for connection
to the potable water mains.
Wear non-slip footwear that will
protect your feet and improve your
footing on slippery surfaces.
Indoor use only. Only use battery
charger indoors.
5
Page 6
Know Your Cordless Pressure Washer
Read the owner’s manual and safety instructions carefully before operating the cordless pressure washer. Compare the
illustration below to the cordless pressure washer in order to familiarize yourself with the location of the various controls and
adjustments. Save this manual for future reference.
1
2 3
4
5
6
7
8
9
10
11
FRONT BACK
19
18
20
17
21
16
22
15
12
13
14
24
25
23
32 34
31
30
282726
33
29
1. Trigger gun
2. Safety lock
3. Trigger
4. Trigger gun holder
5. Spray wand
6. Base unit
7. Front wheel (2)
8. Battery indicator
9. Push button for battery indicator
10. iONMAX 40 V System lithium-iON battery packs featuring
exclusive EcoSharp® technology – Sold separately
40 V 4.0 Ah iONMAX (model iBAT40)
40 V 5.0 Ah iONMAX PRO (model iBAT40XR)
40 V 6.0 Ah iONMAX PRO (model iBAT40XRP)
11. iONMAX iCHRG40 lithium-ion battery charger
– Sold separately
12. Push lock button
13. Quick-connect collar
14. High-pressure hose
15. Battery compartment
16. Control panel
17. Bucket handle
18. Tow handle
19. Bucket lid
20. High-pressure hose strap
21. Bucket buckle (2)
22. Water outlet/high-pressure hose connection
23. Needle clean-out tool
24. Garden hose adapter/connection
25. 40º Quick-Connect nozzle (gray)
26. 25º Quick-Connect nozzle (green)
27. 15º Quick-Connect nozzle (yellow)
28. 0º Quick-Connect nozzle (orange)
29. Soap dispenser attachment
30. All-direction wheel (2)
31. Water bucket
32. Nozzle storage board
33. High-pressure hose connection
34. Trigger lock
6
Page 7
Technical Data
Battery Voltage* 40 V D.C.
Battery Capacity 4.0 Ah (model iBAT40†)
5.0 Ah (model iBAT40XR†)
6.0 Ah (model iBAT40XRP†)
Charge Time Max 3 hours (using iBAT40 with
iCHRG40†)
3.5 hours (using iBAT40XR
with iCHRG40†)
5 hours (using iBAT40XRP
with iCHRG40†)
Battery Run Time Max 21 min (using iBAT40†)
31 min (using iBAT40XR†)
35 min (using iBAT40XRP†)
Motor 600 W brushless
Max Water Inlet Temperature 104ºF/40ºC
Removable Bucket Capacity 5.3 gal (20 l)
High Pressure Hose Length 20.3 ft (6.2 m)
Soap Dispenser 8.5 oz (250 ml)
Attachment Capacity
Max Water Inlet Pressure 0.7 MPa
Max Rated Flow 0.79 GPM
Max Flow 1 GPM
Pressure Select Technology LOW/500 PSI
MEDIUM/650 PSI
HIGH/800 PSI
Max Pressure 1160 PSI
Weight (without battery) 20 lbs (9.1 kg)
*Initial no-load voltage, when fully charged, peaks at 40 volts; nominal voltage
under typical load is 36 volts.
†
Sold separately.
• Soap dispenser attachment
• Trigger gun holder
• High-pressure hose
• Garden hose adapter (female coupler)
• Manual with registration card
1. Carefully remove the pressure washer and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new cordless
pressure washer. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
mWARNING! Do not insert the battery until assembly is
complete. Failure to comply could result in accidental starting
and possible serious personal injury.
Assembly
1. The washer must be used on a secure and stable surface
in a standing, upright position (Fig. 1).
Fig. 1
Unpacking
Carton Contents
• Water bucket assembly
• Bucket lid
• Base unit
• Trigger gun
• Spray wand
• Four (4) Quick-Connect nozzles (0º, 15º, 25º, and 40º)
• Needle clean-out tool
2. Open the box, take out the bucket lid, bucket and the
base unit (Fig. 2).
7
Page 8
Fig. 2
Fig. 4
Bucket lid
Bucket
Bucket
Base unit
3. Insert the trigger gun holder onto the bucket (Fig. 3).
Fig. 3
Trigger
gun holder
Water inlet
Bucket outlet
5. Flip up the buckles on the base unit and latch to bucket.
Press down on the buckle ends to lock the bucket to the
base unit (Fig. 5).
Fig. 5
1. Flip up
Bucket buckle
2. Press the end
Base unit
4. Align the water inlet on the base unit with the outlet on
the bottom of the bucket, and seat the bucket on the
base unit. Check alignment to ensure a proper seal and
connection (Fig. 4).
mWARNING! When the water bucket is xed on the base
unit, do not lift the pressure washer by the handle. Instead, use
the tow handle to pull the pressure washer unit along on its
wheels (Fig. 6).
Fig. 6
8
Page 9
6. Take the spray wand and align the two tabs with your
trigger gun. Once aligned, push the spray wand rmly into
the trigger gun, twist counter-clockwise to lock into place
(Fig. 7).
Fig. 7
Spray wand
Trigger gun
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and
replace if damaged. Do not attempt to mend a damaged hose.
8. Connect the high-pressure hose to the base unit by
inserting the other end into the water outlet. While pushing
rmly in on the hose, twist the outer collar clockwise until
tight to ensure a water-tight connection (Fig. 10).
Fig. 10
Water outlet
7. Unlock the lock latch by sliding it down, and insert the
high pressure hose into the high pressure hose connection
on the end of the trigger gun. Slide the latch back to lock
the hose in place (Figs. 8 – 9).
Fig. 8
Lock latch
High-pressure hose
Fig. 9
High-pressure
hose
Twist clockwise while
pressingrmly
9. Put the trigger gun with spray wand assembly on the gun
holder. Your pressure washer is ready for use (Fig. 11).
Fig. 11
High-pressure hose
Lock latch
9
Page 10
Battery Pack Operation
The equipment is powered by a lithium-ion battery. The battery
pack is completely sealed and maintenance free.
Battery Charge Level Indicator
The battery pack is equipped with a push button for checking
the charge level. Simply press the push button to read o the
battery charge level from the LEDs of the battery indicator:
• All 3 level monitoring LEDs are lit: Battery charge level
is high.
• 2 level monitoring LEDs are lit: Battery charge level is
decreasing. Stop work as soon as possible.
• 1 level monitoring LED is lit: Battery is at. Stop work
IMMEDIATELY and charge the battery. Otherwise the
battery’s service life will be greatly shortened.
Light IndicatorsLights
Charge level button
The battery is at 30% capacity
and requires charging
The battery is at 60% capacity
and requires charging soon
When to Charge the iONMAX 40 V
System Lithium-Ion Battery
NOTE: The iONMAX 40 V System lithium-ion battery packs
do not develop a "memory" when charged after only a partial
discharge. Therefore, it is not necessary to run down the
battery pack before placing it into the charger.
• Use the battery charge indicator lights to determine when to
charge your iONMAX 40 V System lithium-ion battery pack.
• You can "top-o" your battery pack's charge before starting
a big job or after a long day of use.
Charging the Battery
1. Open the battery compartment cover. Slide the push lock
button on the battery to remove the battery pack from the
base unit (Fig. 12).
Fig. 12
The battery is at full capacity
NOTE: If the charge level button does not appear to be
working, place the battery pack on the charger and charge as
needed.
NOTE: Immediately after using the battery pack, the charge
level button may display a lower charge than it will if checked
a few minutes later. The battery cells “recover” some of their
charge after resting.
Charger Operation
mWARNING! Charge only iONMAX 40 V System lithium-
ion battery packs in compatible iONMAX iCHRG40 lithium-ion
battery chargers. Other types of batteries may cause personal
injury and damage.
To reduce the risk of electric shock, do not allow water to ow
into the charger's AC/DC plug.
Push lock
button
2. Check that the mains voltage is the same as that marked
on the rating plate of the battery charger. Then, insert the
charger's plug into the electrical wall outlet. When you
plug in the charger, the top green light will illuminate and
stay green (Fig. 13).
10
Page 11
Fig. 13
NOTE: If the top light remains green while the bottom light
alternately ashes red and green, this indicates a temperature
abnormality (i.e. that the battery pack is either too hot or too
cold). If there is only a red blinking light, this indicates that
something is wrong with the battery. Contact Snow Joe® +
Sun Joe® customer service center at 1-866-SNOW-JOE
(1-866-766-9563) for assistance.
green
Power on
3. Place the battery pack into the charger by sliding the
pack as shown to lock it into position. When you insert
the battery into the charger, the bottom red light will
illuminate to indicate that the battery is charging (Fig. 13).
4. When the bottom light turns green, the battery is fully
charged (Fig. 14).
Fig. 14
Green
Flashing red/green
Temperature abnormal
5. A fully discharged iBAT40 battery pack with an internal
temperature in the normal range will fully charge in up
to 3 hours (between 32ºF/0ºC and 113ºF/45ºC). A fully
discharged iBAT40XR battery pack with an internal
temperature in the normal range will fully charge in
up to 3.5 hours (between 32ºF/0ºC and 113ºF/45ºC).
A fully discharged iBAT40XRP battery pack with an
internal temperature in the normal range will fully charge
in up to 5 hours (between 32ºF/0ºC and 113ºF/45ºC).
Heavily cycled battery packs may take longer to charge
completely.
6. If the charging light indicator alternately blinks red and
green or the light indicator does not come on at all, check
that the battery pack is fully seated into the bay. Remove
the pack and reinsert. If the problem persists, contact the
Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563) for assistance.
7. When charging is complete, remove the battery from the
charger by pulling the push lock button and sliding the
battery backward to unlock it from the charger (Fig. 15).
Fig. 15
Flashing red only
Something is wrong
Charging
green
red
green
green
Fully charged
Push lock button
8. Timely recharging of the battery will help prolong the
battery's life. You must recharge the battery pack when
you notice a drop in the equipment's power.
IMPORTANT! Never allow the battery pack to become fully
discharged as this will cause irreversible damage to the
battery.
11
Page 12
Charging a Hot or Cold Battery Pack
A red and green ashing indicator light on the charger
indicates that the battery pack temperature is outside the
charging range. Once the pack is within the acceptable
range, normal charging will take place and the red light will
be continuous. Hot or cold battery packs may take longer to
charge.
Lithium-Ion Charging Status
Fig. 17
Battery Pack
Temperature
Too hot Flashing Not charging
Normal range Continuous Normal charging
Too cold Flashing Not charging
Red Charger
Indicator Light
Charging
Status
Operation
mIMPORTANT! This pressure washer is equipped with
a micro-switch sensitive to water ow. This Total Stop System
(TSS) senses water ow in the pump. When the trigger is
released, water stops owing through the pump. The TSS then
automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
The TSS system will work only when there's water in the
bucket or the base unit is connected with a water supply.
When there's no water connected with the unit, the On/O
button has to be pressed to stop the unit.
mIMPORTANT! This system is capable of producing
8 Mpa. To avoid rupture and injury, do not operate this pump
with components rated less than 8 Mpa working pressure
(including but not limited to spray guns, hose, and hose
connections).
1. Open the battery compartment cover and slide the battery
in until it clicks to lock it into position, then close the
battery compartment cover (Fig. 16).
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC.
mCAUTION! The washer must only be used with clean
(fresh) water; use of unltered water containing corrosive
chemicals will damage the washer.
mWARNING! Do not ll the bucket with the bucket still
xed on the base unit.
3. Put the bucket back on the base unit. Make sure the
bucket is properly aligned on the base. Latch and lock
the buckles to ensure the bucket is securely connected
before using (Figs. 4 – 5).
NOTE: If you do not want to use the bucket, you can use
the base unit directly as a pressure washer. See following
instructions (step 4 – 5) to learn how to connect the base unit
with a water supply.
4. Connect the garden hose adapter (female coupler) to
the water inlet of the pressure washer on the base unit,
then thread your garden hose (male end) into the garden
hose adapter (Fig. 18). The garden hose must have an
internal diameter of at least 13 mm (1/2 in.) and must be
reinforced. The water supply must be at least equal to the
washer delivery capacity.
Fig. 16
Battery
compartment
cover
2. Remove the water bucket from the base unit and ll with
clean (fresh) water (Fig. 17).
12
Page 13
Fig. 18
PRESSURE SELECT
Fig. 20
Garden hose
Safety lock
Garden hose adapter
Water inlet
Base unit
5. Attach garden hose to water supply (Fig. 19).
mWARNING! Water that has owed through back ow
preventers is considered to be non-potable.
mWARNING! The water supply must not exceed 0.7Mpa.
Fig. 19
Trigger
8. Keeping the trigger pressed, turn on the unit by pressing
the On/O button on the control panel. Using the "Pressure
Select" feature, you can also choose from three dierent
pressure settings by pressing the + or - button on the right
side of the control panel (Fig. 21).
Fig. 21
Control panel
+
W
E
O
R
P
Connect to water supply
Garden hose
6. If only using the base unit, turn the water supply tap on
completely.
7. Push the safety lock on the spray gun handle, then press
the trigger for a few seconds until the water ow is steady.
Operating the pressure washer in this manner will allow
air to escape and discharge residual pressure in the hose
(Fig. 20).
NOTE: This machine is equipped with 3 selectable power/
pressure levels. See table below for detailed specs.
Power
Light
indication
Ratedow
pressure
– O
Low 0.66 GPM 507 PSI
– O
– On
– O
Medium 0.75 GPM 650 PSI
– On
– On
– On
High 0.79 GPM 800 PSI
– On
– On
9. When re-starting the motor, always keep the trigger
pressed.
NOTE: The motor only runs when the trigger is operated
and shuts o when the trigger is released.
13
Rated
Page 14
Using the Nozzles
Before beginning any cleaning task, determine the best nozzle
for the job. Each nozzle has a dierent spray pattern. The
nozzle patterns are 40˚ (for gentle cleaning), 25˚ (for allpurpose cleaning), 15˚ (for tough jobs), and 0˚ (for spot
cleaning or hard-to-reach areas) .
mCAUTION! NEVER change nozzles without locking the
safety lock on the trigger handle.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
This cordless pressure washer is equipped with four (4) QuickConnect nozzles that easily snap onto the Quick-Connect
collar of the spray wand.
To connect a nozzle to the spray wand:
1. Turn o the pressure washer, remove the bucket or shut
o the water supply. Pull the trigger to release water
pressure.
2. Lock the safety lock on the trigger handle by pushing on
the safety lock until it clicks into the slot.
3. Pulling the quick-connect collar backwards, at the same
time, snap the desired nozzle onto the quick-connect
collar until it clicks into place, then release the quickconnect collar (Fig. 22).
Working with Detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
mWARNING! Use only detergents specically designed
for use with pressure washers, such as Sun Joe® HOUSE +
DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO
WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER
(SPX-APC1G). DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, ammable material, or
industrial grade solutions. These could damage the pressure
washer. Many detergents may require mixing prior to use.
Prepare the cleaning solution as instructed on the solution
bottle.
1. Remove the spray wand attachment from the trigger gun.
2. Remove the soap dispenser sprayer from the bottle and
ll with mixed detergent. Put the sprayer back on when
nished (Fig. 23).
Fig. 23
Soap dispenser sprayer
Fig. 22
Spray wand
Quick-Connect collar
To disconnect a nozzle from the spray wand once the cleaning
job is complete:
4. Turn o the pressure washer and remove the water
bucket/shut o the water supply. Pull the trigger to release
water pressure.
5. Lock the safety lock on the trigger handle by pushing on
the safety lock until it clicks into the slot.
6. Remove the nozzle by placing your hand over the nozzle
while pulling back on the Quick-Connect collar.
Nozzle
“Click”
mWARNING! Do not make changes to the nozzle while
the trigger is engaged. Doing so could result in damage to the
pressure washer or injury to the user.
Pressure washer
detergent
Soap dispenser
bottle
3. Take the soap dispenser attachment and align the two
tabs with your trigger gun. Once aligned, push it into the
trigger gun, and twist counter-clockwise to lock securely
into place (Fig. 24).
14
Page 15
Fig. 24
SOAP
Spray gun
Soap dispenser attachment
4. Turn on the pressure washer. Pull the trigger to operate
the unit.
mCAUTION! Always test the detergent in an
inconspicuous area before use.
5. Apply detergent from the bottom to the top of the dry
surface to be cleaned.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
6. Allow the detergent to remain on the surface for a short
time before rinsing. Do not allow the detergent to dry on
the surface.
mCAUTION! Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse
a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
mCAUTION! Failure to follow these cleaning instructions
will cause the injection system to become clogged and
inoperable.
Rinsing with the Pressure Washer
1. Turn o the pressure washer, remove the bucket or shut
o the water supply.
2. Pull the trigger to release water pressure.
3. Lock the safety lock on the trigger handle by pushing on
the safety lock until it clicks into the slot.
4. Remove the soap dispenser attachment by pushing
rmly in while twisting it clockwise to unlock the tabs
and remove from the slots. Pull the attachment out of the
trigger gun.
5. Attach the spray wand onto the trigger gun.
6. Select the right nozzle for the job (Fig. 25).
Fig. 25
0º
15º
I) The 0º intense-jet nozzle (orange) is an extremely
powerful nozzle that delivers a high-pressure, pencilpoint jet stream. It is used to cut heavy dirt deposits
in a small, concentrated area. It is ideal for dissolving
stubborn substances, like tar and grease spots on
concrete, or for removing caked mud from equipment.
Use this nozzle to clean hard-to-reach areas including
the facades of 2-story buildings or the undersides of
lawn mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
II) Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from this
nozzle.
III) Use the 25º fan-tip nozzle (green) to clean home
siding, brick patios, wood decks, driveways, or
sidewalks. When using this nozzle, test a small area
rst to avoid surface damage.
IV) Use the 40º wide-spray tip nozzle (gray) to clean items
such as cars, trucks, boats, patio furniture, or lawn
equipment.
7. Lock the bucket with water on the base unit or connect
the base unit with a water supply. Start at the top of the
area to be rinsed and work your way down, making sure
to overlap your strokes.
25º
40º
mIMPORTANT! NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
• Liquids containing solvents (e.g. paint thinners, gasoline,
oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and will damage the
cleaning surface.
15
Page 16
Shutting Down
1. Press the On/O button on the control panel.
2. Pour the remaining water out from the bucket or turn o
the water source.
3. Hold the trigger to release water pressure.
4. If using the base unit directly, disconnect the garden hose
from the water inlet on the base unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and lock the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a Break
If you are taking a break of ve minutes or more between
cleaning tasks:
1. Lock the gun safety lock.
2. Push the On/O button to stop the machine.
Storage
• Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before
storing for the winter.
mWARNING! Before reusing, completely ush the unit
out with clear water. Anti-freeze products can damage
paintwork, so you must ensure there is no anti-freeze left in the
system before using it again.
Maintenance
mCAUTION! Before working on the pressure washer,
remove the battery from the compartment.
1. To ensure good performance, check and clean the water
inlet lter. Remove the lter and rinse with warm water to
prevent any foreign matter from clogging the pump
(Figs. 26 – 27).
Fig. 26
Garden hose adapter
Water
inletlter
Base unit
mCAUTION! Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
• Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
• It is important to store this product in a frost-free area.
• Always empty water from all hoses, the pump, the soap
dispense attachment and the bucket before storing.
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Winterizing + Long-Term Storage
If you must store your pressure washer in a location where
the temperature falls below 32ºF (0ºC), you can minimize the
chance of damage to your machine by utilizing the following
procedure:
• Disconnect all water connections.
• Turn on the machine for a few seconds until the remaining
water in the pump exits. Turn o immediately.
• Do not allow the high-pressure hose to become kinked.
• Store the machine and accessories in a room that does
not reach freezing temperatures.
• Do not store near a furnace or other sources of heat that
may dry out the pump seals.
Fig. 27
Waterinletlter
2. Clean the nozzle with the needle clean-out tool provided
(Fig. 28). Remove the spray wand from the gun; remove
any dirt from the nozzle hole and rinse.
16
Page 17
Fig. 28
Battery Caution + Disposal
Always dispose of your battery pack according to federal,
state, and local regulations. Contact a recycling agency in your
area for recycling locations.
15º
Needle clean-out tool
3. Remove additional debris by back ushing water through
the nozzle and spray wand. To do this, place the end of
your garden hose (with water running) to the tip of the
nozzle, pushing water and debris out of the back opening
of the nozzle and spray wand.
Disposal
Recycling the Washer
• Do not dispose of electrical appliances as unsorted
municipal waste. Use separate collection facilities.
• Contact your local government agency for information
regarding the collection systems available.
• If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your
health and well-being.
• When replacing old appliances with new ones, the retailer
is legally obligated to take back your old appliance for
disposal at least free of charge.
Recycling + Disposal
The product comes in a package that protects it against
damage during shipping. Keep the package until you are
sure that all parts have been delivered and the product is
functioning properly. Recycle the package afterwards or keep
it for long-term storage.
WEEE symbol. Waste electrical products should not
be disposed of with household waste. Please
recycle where facilities exist. Check with your local
authority or local store for recycling regulations.
mCAUTION! Even discharged battery packs contain
some energy. Before disposing, use electrical tape to cover
the terminals to prevent the battery pack from shorting, which
could cause a re or explosion.
mWARNING! To reduce the risk of injury or explosion,
never burn or incinerate a battery pack even if it is damaged,
dead or completely discharged. When burned, toxic fumes
and materials are emitted into the surrounding atmosphere.
1. Batteries vary according to device. Consult your manual
for specic information.
2. Install only new batteries of the same type in your product
(where applicable).
3. Failure to insert batteries in the correct polarity, as
indicated in the battery compartment or manual, may
shorten the life of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc) or
Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or
Lithium-Ion) batteries.
6. Do not dispose of batteries in re.
7. Batteries should be recycled or disposed of as per state
and local guidelines.
Service + Support
If your Sun Joe® iON SPX6001C-CT cordless pressure washer
requires service or maintenance, please call the Snow Joe® +
Sun Joe® customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Model + Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Record the following numbers from the housing or handle of your
new product:
S P X 6 0 0 1 C - C T
Model #:
Serial #:
17
Page 18
Troubleshooting
• Remove the battery from the compartment before carrying out maintenance on the machine or when checking that its parts
are in proper working order.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses
to start
Fluctuating pressure
Machine stops
Machine pulsating
• Power failure/Battery is not
inserted well
• Pump sucking air
• Valves dirty, worn out, or stuck
• Pump seals worn out
• Thermal sensor activated
• Nozzle partially blocked
• Battery is at
• Air in inlet hose
• Inadequate supply of mains water
• Nozzle partially blocked
• Water lter blocked
• Hose kinked
• Check to make sure the battery has sucient
power and is inserted well
• Check the hoses and connections are airtight
• Clean or replace valves/seals
• Please call the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563)
for assistance
• Leave the washer for 5 minutes to cool down
• Clean the nozzle
• Charge the battery.
• Allow machine to run by holding the trigger until
regular working pressure resumes
• Check that the water supply corresponds to the
specications required
• WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter)
• Clean the nozzle
• Clean the water inlet lter
• Straighten out the hose to remove any kinks/blockages
Machine often starts
and stops by itself
Machine starts, but
no water comes out
• Pump/spray gun is leaking
• Trigger mechanism is broken
• Pump/hoses or accessories frozen
• No water supply
• Water inlet lter blocked
• Nozzle blocked
• Please call Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance
• Wait for pump/hoses or accessories to thaw
• Connect inlet water
• Clean the water inlet lter
• Clean the nozzle
18
Page 19
Optional Accessories
mWARNING! ALWAYS use only authorized Snow Joe
replacement parts or accessories that are not intended for use with this cordless pressure washer. Contact Snow Joe® +
Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The
use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
®
+ Sun Joe® replacement parts and accessories. NEVER use
ModelAccessories Item
1
2
3
iONMAX 40 V 4.0 Ah Lithium-Ion Battery
Battery Charge Time Max:
iCHRG40: 3 hours
iCHRG40-DPC: 3.5 hours
Battery Run Time Max: 21 min
iONMAX 40 V 5.0 Ah PRO SERIES
Lithium-Ion Battery
Battery Charge Time Max:
iCHRG40: 3.5 hours
iCHRG40-DPC: 4 hours
Battery Run Time Max: 31 min
iONMAX 40 V 6.0 Ah PRO SERIES
Lithium-Ion Battery
Battery Charge Time Max:
iCHRG40: 5 hours
iCHRG40-DPC: 5.5 hours
Battery Run Time Max: 35 min
iBAT40
iBAT40XR
iBAT40XRP
4
iONMAX 40 V Lithium-Ion Battery Charger
iCHRG40
5
iONMAX 40 V Lithium-Ion Dual Port Battery
Charger
iCHRG40-DPC
Sun Joe’s complete line of premium pressure washer accessories and attachments
make it easy to get your dirty work done, and also help you get the most out of your model!
SHOP ONLINE now at sunjoe.com
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563).
19
Page 20
NOTES
20
Page 21
NOTES
21
Page 22
NOTES
22
Page 23
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience as pleasant
as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We
think it’s important that you know what you can expect from us. That’s why we created the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product does
not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending
you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting,
sawing, mowing, washing and…?
PRODUCT REGISTRATION:
Snow Joe®, LLC (“Snow Joe® + Sun Joe®”) strongly encourages
you to register your purchase. You can register online at
snowjoe.com/ProductRegistration, or by printing and mailing
in a registration card available online from our website, or
calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at help@snowjoe.com.
Failure to register your product purchase will not diminish your
warranty rights. However, registering your purchase will allow
Snow Joe® + Sun Joe® to better serve you with any of your
customer service needs.
WHO CAN SEEK WARRANTY COVERAGE?
This Warranty is extended by Snow Joe® + Sun Joe® to the owner
of this Machine (a “Machine” consists of a product powered by
a motor) for residential and personal household use only. This
Warranty does not apply to products used for commercial, rental
or re-sale purposes. Should ownership of this machine change
during the 2-year period, please update the Machine’s owner
information at snowjoe.com/ProductRegistration.
WHAT IS COVERED?
Snow Joe® + Sun Joe® warrants to the owner that if this Machine
fails within 2 years from the date of purchase due to a defect in
material or workmanship or as a result of normal wear and tear
from ordinary household use, Snow Joe® + Sun Joe® will send a
replacement part or product, as needed, free of charge and with
free shipping to the original purchaser.
If, in Snow Joe® + Sun Joe®’s sole discretion, the failed Machine
cannot be repaired with a part, Snow Joe® + Sun Joe® will elect to
either (A) send a new Machine at no charge and with free shipping
or (B) refund the full purchase price to the owner.
WHAT IS NOT COVERED?
This Warranty does not apply to the Machines that have been used
commercially or in non-household applications. This Warranty
does not cover cosmetic changes that do not aect performance.
This Warranty is only valid if the Machine is used and maintained
in accordance with the instructions, warnings and safeguards
contained in the owner’s manual. Snow Joe® + Sun Joe® will not
be responsible for the cost of any unauthorized warranty repairs.
This warranty does not cover any cost or expense incurred by
the purchaser in providing substitute equipment or service during
reasonable periods of malfunction or non-use of this product
while waiting for a replacement part or unit under this warranty.
Wearing parts like belts, augers, chains and tines are not covered
under this warranty, and can be purchased at snowjoe.com or
by calling 1-866-SNOWJOE (1-866-766-9563). Batteries are
covered in full for 90-days from the date of purchase.
Repair, replacement or refund of the purchase price are the
exclusive remedies of purchaser and the sole liability of Snow Joe®
+ Sun Joe® under this warranty. No employee or representative
of Snow Joe® + Sun Joe® is authorized to make any additional
warranty or any modication to this warranty which may be
binding upon Snow Joe® + Sun Joe®. Accordingly, purchaser
should not rely upon any additional statements made by any
employee or representative of Snow Joe® + Sun Joe®. In no event,
whether based on contract, indemnity, warranty, tort (including
negligence), strict liability or otherwise, shall Snow Joe® +
Sun Joe® be liable for any special, indirect, incidental, or
consequential damages, including, without limitation, loss of
prot or revenue.
Some states do not allow limits on warranties. In such states, the
above limitations may not apply to you.
Outside the USA, other warranties may apply.
23
Page 24
snowjoe.com
Loading...