sunjoe SBJ603E Operator's Manual

© 2017 by Snow Joe®, LLC All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
A Division of Snow Joe®, LLC
OPERATOR’S MANUAL
Model SBJ603E Form No. SJ-SBJ603E-880E-MR4
R
ELECTRIC BLOWER / VACUUM / MULCHER
13-AMP | 17:1 REDUCTION RATIO
IMPORTANT!
Safety Instructions
All Operators Must Read These Instructions Before Use
Any electrical appliance can be dangerous if used incorrectly. Some of the safety precautions given in this manual apply
generally to many appliances. Other warnings are specic to
the use of this electric blower vac.
Always follow these safety guidelines. Failure to do so may result in serious bodily injury or death.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
General Safety
FOR HOUSEHOLD USE ONLY
Before using, be sure that everyone using this tool reads and understands all safety instructions and other information contained in this manual. Save this manual and review it frequently prior to using this tool and when instructing others on the proper operating procedures.
mCAUTION! Wear appropriate hearing protection during
use. After long periods of extended use, the noise generated from this appliance may cause hearing loss if your ears are not properly protected.
mWARNING! When using electric yard tools, basic safety
precautions should always be followed to reduce the risk of
re, electric shock and personal injury, including the following:
1. Keep work area clean and well-lit – Cluttered, dark areas invite accidents.
2. Replacement parts – When servicing this unit, use only identical replacement parts. Replace or repair damaged cords immediately.
3. Keep children, bystanders and pets away – All spectators, including pets, should be kept a safe distance away from the work area.
4. Dress properly – Do not wear loose clothing or jewelry as such articles can become caught in moving parts. Wear a protective covering to contain long hair. Wearing rubber gloves and substantial non-slip footwear is recommended when working outdoors.
5. Extension cords – To prevent electric shock, use only with an extension cord suitable for outdoor use.
6. Avoid accidental starting – Do not carry the blower vac
with your nger on the switch. Make sure the switch is o
before plugging in the unit.
mDANGER! Do not manually place objects into the
vacuum tube while operating the unit as this can seriously damage the unit and/or harm the operator. Keep both hands on the handles while the power is on.
DO NOT ATTEMPT to remove material or hold material to be
vacuumed when the blower vac is on. Make sure the blower vac is o when clearing jammed material from the vacuum
tube. Do not pick up the blower vac by the tube or attempt to carry the unit by the tube.
mCAUTION! Moving parts will continue to run for several
seconds after turning o the machine.
7. Do not abuse the cord – Never carry the blower vac by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges.
8. Moving parts – Keep hands and feet away from moving parts. Keep guards in place and in proper working order.
9. Do not force the tool – It will perform better with less likelihood of personal or mechanical injury if it is used at the rate for which it was designed.
10. Wear personal protective equipment – When using this tool, wear safety glasses with side shields or goggles to provide necessary eye protection. Wear ear defenders to prevent hearing damage. Use a face or dust mask if the work environment is dusty.
11. Disconnect the tool – Disconnect the blower vac from the power supply when it is not in use, before servicing it, when changing accessories and when performing any other maintenance task.
12. Store idle tool indoors – When not in use, the blower vac should be stored indoors in a dry and high or locked-up place out of the reach of children.
1
2
13. Maintain the blower vac with care – Keep the blower tube and the fan area clear and clean for optimal performance and to reduce the risk of injury. Inspect the extension cord periodically and immediately replace it if damaged. Keep the handles dry, clean and free from oil and grease. Follow the additional recommendations described in the maintenance section of this manual.
14. Ground fault circuit interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) that are to be used for the blower vac. Receptacles are available having built­in GFCI protection and may be used for this measure of safety.
15. Use the right tool – Do not use the tool for any job except that for which it is intended.
16. Double insulation – Double insulation eliminates the use of the usual three-wire grounded power cords, thereby providing a measure of safety during the operation of electric power tools. In a double insulated appliance, all exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulation tools do not need to be grounded.
NOTE: The double insulated system is intended to protect
the user from shock resulting from a break in the tool's internal insulation. Observe all normal safety precautions to avoid electrical shock.
17. Avoid dangerous environments – Do not use the blower vac in rain, damp or wet locations. Do not operate the blower vac in gaseous or explosive atmospheres or use
the blower vac to pick up ammable or combustible liquids. Motors in these tools normally spark, and the
sparks might ignite fumes.
18. Stay alert – Watch what you are doing. Use common sense. Do not operate the blower vac when you are tired or under the inuence of drugs, alcohol or other medication.
Additional Safety Instructions
• Use extra care when cleaning on stairs.
• Keep rm footing and maintain good balance at all times.
Do not overreach. Overreaching can result in loss of balance.
• Turn o all controls before unplugging the tool.
• Do not use the tool if the power switch does not turn it ON
or OFF. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
• Do not use the tool with a damaged plug. If the tool is not
working as it should or has been dropped, damaged, left outdoors or dropped into water, return it to an authorized Snow Joe
®
+ Sun Joe® dealer or contact the Snow Joe® +
Sun Joe
®
customer service department at 1-866-SNOWJOE
(1-866-766-9563).
• Do not pick up anything that is burning or smoking, such as
cigarettes, matches or hot ashes.
• Do not use without the dust bag and/or lters in place.
• Carefully inspect your appliance prior to use and follow all
label and marking instructions.
• Keep the end of the blower tube away from your face and
body.
• Always unplug this appliance before connecting or
disconnecting the vacuum hose.
• Do not use for wet material.
• Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
• Do not put any object into the tool's openings. Do not use
the tool with any opening blocked; keep openings free of
dust, lint, hair or any other object that may reduce air ow.
• Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire or string which can be thrown or become entangled in the machine.
• Service on the product must be performed by qualied
repair personnel only. Service or maintenance performed
by unqualied personnel could result in injury to the user or
damage to the product.
• This blower vac is intended for residential use only.
Commercial use of this product is prohibited and will void the manufacturer's warranty.
• Never run the unit without the proper equipment attached.
Always ensure the blower tubes are properly installed.
Specic Safety Rules For Blower Vacs
• This tool has been designed for blowing/collecting as well
as vacuuming/shredding dry leaves and other dry garden rubbish, such as grass and twigs.
• When operating the unit as a blower, never point the blower
nozzle in the direction of people or pets or in the direction of windows. Use extra caution when blowing debris near solid objects, such as trees, automobiles and walls.
• Be sure to secure the unit when transporting it.
• Never douse or squirt the unit with water or any other liquid.
Clean the unit after each use as described in the cleaning and storage section.
Electrical Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for this electric blower vac. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
2. Make sure that the mains voltage matches that listed on
the unit's rating label. Using the improper voltage can damage the motor and injure the user.
3. To prevent electric shock, use only with an extension cord suitable for outdoor use, such as SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
3
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to use one heavy enough to carry the current your product will draw. For lengths less than 50 ft (15 m), a No.14 AWG (or greater) extension cord should be used. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
4. To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other). Use this appliance only with a polarized UL-, CSA- or ETL­listed extension cord recommended for outdoor, all-weather use, such as the Snow Joe
®
+ Sun Joe®
SJTW-A 14-gauge 50-foot extension cord with lighted
end (Model PJEXT50-B). Visit snowjoe.com to purchase
this extension cord online or, to order by phone, call 1-866-SNOWJOE (1-866-766-9563).
The appliance plug will t into a polarized extension
cord only one way. If the appliance plug does not t
fully into the extension cord, reverse the plug. If the plug
still does not t, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. The extension cord plug will t into
the polarized wall outlet only one way. If the plug does
not t fully into the wall outlet, reverse the plug. If the plug still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug, extension cord receptacle or extension cord plug in any way.
5. To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.
6. Do not abuse the cord. Never pull the blower vac by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges.
Extension Cord
Length
Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
+50 ft - 100 ft
(+15 m - 30 m)
14 12
m WARNING m
Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:
• Do not allow any part of the electric blower vac to
make contact with water while it is in operation. If the
appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA- or ETL-rated extension cord
for outdoor, all-weather use, such as the Snow Joe
®
+
Sun Joe
®
SJTW-A 14-gauge 50-foot extension cord
with lighted end (Model PJEXT50-B). Visit snowjoe.
com to purchase this extension cord online or, to order by phone, call 1-866-SNOWJOE (1-866-766-9563).
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
4
Double-Insulated Appliances
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double­insulated appliance requires extreme care and knowledge
of the system, and should be performed only by qualied
service personnel at an authorized Snow Joe
®
+ Sun Joe® dealer. Replacement parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “Double Insulation” or “Double Insulated.” The symbol
(square within a square)
may also be marked on the appliance.
DOUBLE-INSULATED: GROUNDING NOT
REQUIRED. WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS.
This electric blower vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacement parts. Read the instructions before servicing double-insulated appliances. Use this blower vac only as described in this manual.
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand and follow all instructions on the machine before attempting to assemble and operate.
READ THE OPERATOR'S MANUAL(S) – Read,
understand and follow all instructions in the user manual(s) before attempting to assemble and operate.
SAFETY ALERT – Indicates a precaution, a warning or a danger.
Immediately remove the plug from the mains if the power cable is damaged, frayed or entangled. Always keep the power cable away from heat, oil and sharp edges.
DOUBLE INSULATION – When servicing, use only identical replacement parts.
WARNING! Do not expose the
unit to rain or wet conditions.
Wear hearing protection. Wear eye protection. Wear breathing protection.
Keep bystanders and children a safe distance away.
Symbols SymbolsDescriptions Descriptions
DANGER! Rotating blades
pose a serious risk of injury. Keep hands and feet away from openings while the machine is running.
The rotating part will continuously run for several seconds after you
turn o the machine.
Beware of ying objects
and debris.
WARNING! Turn the machine OFF and disconnect it from the power supply before inspecting, cleaning, changing accessories or conducting any other maintenance task.
5
6
Know Your Electric Blower/Vacuum/Mulcher
Read the owner’s manual and safety instructions carefully before operating the electric blower vac. Compare the illustration below to the electric blower vac in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
1. Variable blower speed control (speed settings 1 to 6)
2. Cord retainer
3. Appliance cord
4. Vacuum/mulcher inlet cover
5. Vacuum/mulcher inlet cover lock button
6. Rear vacuum/mulcher tube
7. Front vacuum/mulcher tube
8. Strap holder
9. Collection bag
10. Handle
11. ON/OFF switch
12. Auxiliary handle
13. Tube release button
14. Blower tube
15. Blower concentrator nozzle
Technical Data
Rated Voltage 120 V ~ 60 Hz
Power 13 A
No Load Speed 10000 – 16000 rpm
Impeller Heavy-duty nylon
Air Speed (max) 240 MPH
Blower Air Flow (max) 300 CFM
Vacuum Air Flow (max) 421 CFM
Variable Speed Settings 6
Mulch Reduction Ratio 17:1
Mode Conversion Blower to mulching vacuum
Bag Capacity 12 gal (45 l)
Blower Weight 6.4 lbs (2.9 kg)
Vacuum/mulcher Weight 8.8 lbs (4 kg)
R
1110 12
13
14
15
4
6
7
2
3
5
1
8
9
7
Unpacking
Carton Contents
• Electric blower/vacuum/mulcher
• Blower tube
• Blower concentrator nozzle
Front vacuum/mulcher tube
Rear vacuum/mulcher tube
Collection bag
• Manuals with registration card
1. Carefully remove the electric blower/vacuum/mulcher and check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or missing parts, DO NOT return the unit to the store. Please
call the Snow Joe
®
+ Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use the electric blower/ vacuum/mulcher. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small
parts. These items can be swallowed and pose a suocation
risk!
Assembly
m
WARNING! To avoid serious personal injury, read and
understand all safety instructions provided.
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
mWARNING! Before performing any maintenance, make
sure the tool is unplugged from the power supply. Failure to heed this warning could result in serious personal injury.
mWARNING! To prevent serious personal injury, make
sure the switch is in the OFF (O) position, the unit is unplugged and the impeller has come to a complete stop before attaching or removing tubes.
Assemble as a Blower
1. Slide the blower tube forward until the notched area on
the blower housing clicks into the slot on the blower tube (Fig. 1).
2. Insert the concentrator nozzle onto the end of the blower tube until it locks into position (Fig. 1).
NOTE: The concentrator nozzle is used to increase
air ow in tight areas (i.e around ower beds, under decks, etc.).
3. Before using the blower function, securely fasten the inlet cover over the air inlet by closing the inlet cover until the lock button snaps into the locked position (Fig. 2).
4. To remove the blower tube, turn the ON/OFF power switch to the OFF (O) position and disconnect the tool from the power supply.
5. Press the tube release button and remove the blower tube
(Fig. 3).
Fig. 1
Notched area
Slot
Blower tube
Air outlet
Concentrator nozzle
Fig. 2
Inlet cover lock button
Inlet cover
Fig. 3
Tube release button
Blower tube
ON/OFF switch
8
Assemble as a Vacuum/Mulcher
1. Slide the front and rear vacuum/mulcher tubes together
until the lock button engages (Fig. 4).
2. Slide the inlet cover lock button forward to disengage the inlet cover. Hold the cover open (Fig. 5).
3. With the blower tube removed, insert the "hooked" side end of the mulcher tube into the rear clip on the unit. Securely fasten the mulcher tube by pushing the "wedged" side end of the mulcher tube up until the lock button snaps into the locked position (Fig. 6).
4. Insert the collection bag adaptor into the blower air outlet until the collection bag is securely fastened (Fig. 7), then clip the bag to the strap holder. Simply press the tube release button to remove the bag (Fig. 8).
5. To remove the vacuum/mulcher tube assembly, slide the inlet cover lock button to unlock, then remove the tube assembly from its housing (Fig. 9).
NOTE: It may be necessary to remove the blower tube or
vacuum/mulcher tubes to clear a blocked tube or impeller.
Make sure to disconnect the unit from the power supply
before attempting to clear any obstructions.
Fig. 4
Rear tube Front tube
Fig. 5
Inlet cover lock button
Inlet cover
Fig. 6
Rear clip + Hook side
Wedged side
R
Fig. 7
Collection bag
Air outlet
Collection bag adaptor
R
Fig. 8
Tube release button
Fig. 9
Inlet cover
lock button
9
Operation
Connecting to a Power Source
1. Secure the extension cord to the motor housing using the
cord retainer located at the rear of the blower. Securing the extension cord in this manner prevents accidental removal of the electrical cord during operation (Fig. 10).
2. Plug the female end of the electrical cord into the
receptacle at the back of the unit.
Starting and Stopping
1. To start the electric blower/vacuum/mulcher, slide the
ON/OFF switch to position (I) (Fig. 11).
2. To stop the unit, slide the ON/OFF switch to position (O) (Fig. 11).
Speed Control
This unit is equipped with six variable speed settings (1 to 6) (Fig. 12).
• Turn the speed dial to position “1” or “2” for LOW speeds.
• Turn the speed dial to position “3” or “4” for MEDIUM speeds.
• Turn the speed dial to position “5” or “6” for
HIGH speeds.
Operating Tips
mWARNING! Use the blower/vacuum/mulcher only in
daylight or good articial light.
• When using the blower vac, plant your feet rmly on the
ground and place one hand on the unit handle and the other hand on the auxiliary handle.
Wear personal protective equipment during your work session. This includes boots, safety glasses/goggles, ear defenders, long pants and a long-sleeve shirt.
• When using the unit as mulcher, make sure the bag is
properly installed and zipped closed.
• Make sure the blower tube nozzle is not directed at
anybody or any loose debris before starting the unit.
• Verify that the unit is in good working condition. Make sure
the tubes and guards are in place and secure.
• Ensure that the vacuum/mulch inlet cover is completely
closed and locked.
• Keep a rm grip on both the front and rear handle or grips.
• To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
• Use the shoulder strap when using the unit as a mulcher.
• Operate power equipment only at reasonable hours—not
early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances.
Usual recommendations are 9:00 am to 5:00 pm, Monday
through Saturday.
• To reduce noise levels, limit the number of pieces of
power equipment used at any one time and operate power blowers at the lowest possible speed setting necessary to do the job.
• Use rakes and brooms to loosen debris before blowing.
• In dusty conditions, slightly dampen surfaces.
Fig. 10
Cord retainer
Extension cord
Fig. 11
ON (I)
OFF (O)
Fig. 12
6 5 4 3 2 1
Variable blower speed control
10
• Conserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches and gardens.
• Blow debris into a safe, open area away from children,
pets, open windows or freshly washed cars.
• Clean up after using leaf blowers and other lawn
equipment. Dispose of debris appropriately.
mWARNING! To avoid serious personal injury, wear
ear defenders, goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations.
mWARNING! To prevent serious personal injury or
damage to the unit, make sure the blower tube or the mulcher tubes and the bag are in place before operating the unit.
Air Vents
Never cover air vents. Keep them free from obstructions and debris. They must always remain clear for proper motor cooling.
mWARNING! To avoid serious personal injury, do not
wear loose tting clothing or articles such as scarves, strings,
chains, ties, etc., that could get drawn into the air vents. To make sure long hair does not get drawn into the air vents, tie back long hair.
Blower Mode
• Hold the blower rmly with one hand on the main handle
and the other hand on the auxiliary handle. Sweep from side to side with the nozzle several inches above the
ground or oor (Fig. 13).
• Slowly advance the unit, keeping the accumulated pile of debris in front of you. Most dry blowing operations are
better suited to low speeds rather than high speeds. High speed blowing is best for moving heavier items like large debris or gravel.
Vacuum/Mulcher Mode
• Once you have blown the debris/leaves into a pile, you
can convert to vacuum mode to collect the debris.
• With a rm hold on the vac, tilt the mulcher tubes 2 – 4 in. (5 – 10 cm) from the ground and use a sweeping
action to collect light debris. The debris will ow into the
bag. Items such as small leaves and twigs will be mulched as they pass through the fan housing. For longer bag life and increased performance, empty the bag frequently (Fig. 14).
• As the bag lls, suction power will decrease. When this
happens, turn the power switch to the OFF (O) position and unplug the unit from the power supply. Remove the bag and empty the debris.
• To remove the bag, press the tube release button (Fig. 8). To empty, hold the plastic handle and grab the nylon handle on the underside of the bag. Turn the bag upside down and shake out any debris and leaves.
mWARNING! Never remove the collection bag without
rst turning the power switch to the OFF (O) position and
unplugging the unit from the main power source.
mWARNING! Do not use in vacuum/mulcher mode
without the vacuum tubes and collection bag in place.
Clearing a Blocked Tube/Impeller
mWARNING! To avoid serious personal injury, be sure
the unit is OFF and unplugged before clearing the impeller.
mWARNING! To avoid serious personal injury, always
wear gloves to protect yourself from the impeller blades or other sharp objects.
Fig. 13
R
Fig. 14
11
During the vacuuming process, certain objects such as cloth, rope or large diameter sticks may obstruct the fan and block the motor. A thermal protection device, which is built into the
blower vac, will cut o the electricity to the motor to prevent
damage from overheating.
In the event an obstruction occurs and power is curtailed:
1. Slide the ON/OFF switch down to the OFF (O) position until the unit comes to a complete stop.
2. Unplug the unit.
3. Remove the blower tube or vacuum/mulcher tubes and
the bag.
4. Using protective gloves, carefully remove the material blocking the tube or impeller. Inspect the blades to ensure no damage has occurred. Rotate the impeller blades by hand to ensure the blockage is completely cleared.
5. Reinstall the blower tube or vacuum/mulcher tubes and the bag.
6. Wait 3 minutes for the motor to cool.
7. Plug the unit back into the power supply and turn the ON/
OFF switch to ON (I). The blower vac will resume normal function.
Maintenance
To order genuine replacement parts or accessories for the Sun Joe
®
SBJ603E electric blower / vacuum / mulcher, please
visit snowjoe.com or contact the Snow Joe
®
+ Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).
mWARNING! Disconnect the extension cord before
performing any maintenance task.
If the extension cord is plugged into the appliance, someone could accidentally turn on the unit while you are performing maintenance on it, which could result in serious personal injury.
Cleaning the Unit
mWARNING! To avoid serious personal injury, always
turn the unit o and unplug it before cleaning or servicing.
Use a small brush to clean the outside of the unit. Do not use strong detergents, household cleaners that contain aromatic oils (e.g. pine and lemon) or harsh solvents such as kerosene as these substances can damage the plastic housing or the
handles. Wipe o any moisture with a soft, dry cloth.
1. Empty the bag after each use to avoid deterioration and
obstructing air ow, which will reduce the performance of
the mulcher.
2. Wear eye protection and a dust mask. Clean the bag as needed. Turn the bag inside out after initial emptying and vigorously shake out dust and debris.
3. Wash the bag once a year, or more often if needed. Follow
the steps below:
i. Remove the bag.
ii. Turn the bag inside out.
iii. Hang it up.
iv. Hose it down thoroughly.
v. Leave it hanging to dry.
vi. Turn the bag right-side up and reinstall.
Storage
1. Examine the electric blower/vacuum/mulcher thoroughly
for worn, loose or damaged parts. Should you need to repair or replace a part, contact an authorized Snow Joe
®
+ Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.
2. Examine the extension cord thoroughly for signs of excess wear or damage. If it is worn or damaged, replace it immediately.
3. Disconnect the extension cord from the electric blower/ vacuum/mulcher before storing.
4. Store the cord with the electric blower/vacuum/mulcher indoors in a clean, dry and locked location out of the reach of children and animals.
NOTE: Devices for retaining extension cords are
commercially available should you wish to purchase one.
Service and Support
If your Sun Joe® SBJ603E 3-in-1 electric blower/vacuum/ mulcher requires service or maintenance, please call the Snow Joe
®
+ Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
Model and Serial Numbers
When contacting the company, reordering parts or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.
Record the following numbers from the housing or handle of your new product:
Model #:
Serial #:
S B J 6 0 3 E
12
Troubleshooting
m
WARNING! Always unplug the power cord before performing any adjustments, maintenance or repairs to your
electric blower vac.
Unit will not blow or mulch
Unit will not start
1. Bag full
2. Blocked tube
3. Blocked impeller
4. Dirty bag
5. Torn bag
6. Bag unzipped
7. Unit unplugged
1. Unit is unplugged.
2. Power/speed switch is in the OFF (O) position.
3. Defective power switch.
4. Vac tubes are not correctly installed.
5. Intake gate/cover is not closed.
6. House circuit may have tripped.
1. Empty the bag.
2. Clear the blockage.
3. Clear the blockage.
4. Clean the bag.
5. Replace the bag.
6. Zip up the bag.
7. Plug into an outlet or an extension cord.
1. Check cord to make sure it is plugged into an electrical
outlet.
2. Slide the power switch to the ON (I) position and select your desired speed setting with the speed control switch.
3. Call the Snow Joe
®
+ Sun Joe® customer service center
at 1-866-SNOWJOE (1-866-766-9563).
4. Check vac tubes and ensure that they are correctly installed to allow the switch to be engaged.
5. Ensure that gate/cover is fully closed and locked.
6. Check wall circuit breaker panel and reset if necessary.
Problem
Possible Cause
Solution
13
Optional Accessories
m
WARNING! ALWAYS use only authorized Snow Joe
®
+ Sun Joe® replacement parts and accessories. NEVER use
replacement parts or accessories that are not intended for use with this electric blower vac. Contact Snow Joe
®
+ Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your electric blower vac. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe
®
+ Sun Joe® to provide notice of such
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe
®
+ Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563).
12-Gallon (45 l) collection bag
18-Gallon (68 l) collection bag
Gutter cleaning blower attachment
Universal wall bracket with mounting hardware
Snow Joe
®
+ Sun Joe® Power Joe SJTW-A 14-gauge 50-foot extension cord with lighted end
SBJ603E-BAG (For use with blower vac
models SBJ601E + SBJ603E + SBJ605E)
SBJ605E-BAG18 (For use with blower vac
models SBJ601E + SBJ603E + SBJ605E)
SBJ6-GA (For use with blower vac models SBJ601E + SBJ603E +
SBJ605E + iONBV)
SJWB (Fits most Snow Joe
®
+ Sun Joe® tools, including blower vac models SBJ601E +
SBJ603E + SBJ605E + iONBV)
PJEXT50-B
ModelAccessories Item
1
2
3
4
5
R
R
14
NOTES
15
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
PRODUCT REGISTRATION:
Snow Joe
®
, LLC (“Snow Joe® + Sun Joe®”) strongly encourages you to register your purchase. You can register online at snowjoe.com/ProductRegistration, or by printing and mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE (1-866-766-9563), or by e-mailing us at help@snowjoe.com. Failure to register your product purchase will not diminish your warranty rights. However, registering your purchase will allow Snow Joe
®
+ Sun Joe® to better serve you with any of your
customer service needs.
WHO CAN SEEK WARRANTY COVERAGE?
This Warranty is extended by Snow Joe
®
+ Sun Joe® to the owner
of this Machine (a “Machine” consists of a product powered by
a motor) for residential and personal household use only. This Warranty does not apply to products used for commercial, rental or re-sale purposes. Should ownership of this machine change
during the 2-year period, please update the Machine’s owner
information at snowjoe.com/ProductRegistration.
WHAT IS COVERED?
Snow Joe
®
+ Sun Joe® warrants to the owner that if this Machine fails within 2 years from the date of purchase due to a defect in material or workmanship or as a result of normal wear and tear from ordinary household use, Snow Joe
®
+ Sun Joe® will send a replacement part or product, as needed, free of charge and with free shipping to the original purchaser.
If, in Snow Joe
®
+ Sun Joe®’s sole discretion, the failed Machine
cannot be repaired with a part, Snow Joe
®
+ Sun Joe® will elect to
either (A) send a new Machine at no charge and with free shipping
or (B) refund the full purchase price to the owner.
WHAT IS NOT COVERED?
This Warranty does not apply to the Machines that have been used
commercially or in non-household applications. This Warranty
does not cover cosmetic changes that do not aect performance. This Warranty is only valid if the Machine is used and maintained
in accordance with the instructions, warnings and safeguards contained in the owner’s manual. Snow Joe
®
+ Sun Joe® will not be responsible for the cost of any unauthorized warranty repairs. This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or unit under this warranty.
Wearing parts like belts, augers, chains and tines are not covered under this warranty, and can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563). Batteries are covered in full for 90-days from the date of purchase.
Repair, replacement or refund of the purchase price are the exclusive remedies of purchaser and the sole liability of Snow Joe
®
+ Sun Joe
®
under this warranty. No employee or representative
of Snow Joe
®
+ Sun Joe® is authorized to make any additional
warranty or any modication to this warranty which may be
binding upon Snow Joe
®
+ Sun Joe®. Accordingly, purchaser should not rely upon any additional statements made by any employee or representative of Snow Joe
®
+ Sun Joe®. In no event, whether based on contract, indemnity, warranty, tort (including negligence), strict liability or otherwise, shall Snow Joe
®
+
Sun Joe
®
be liable for any special, indirect, incidental, or
consequential damages, including, without limitation, loss of
prot or revenue.
Some states do not allow limits on warranties. In such states, the above limitations may not apply to you.
Outside the USA, other warranties may apply.
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience as pleasant as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we created the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product does
not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending
you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting, sawing, mowing, washing and…?
snowjoe.com
mWARNING! This product or its power cord contains chemicals, including lead, known to the State
of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
For more information go to www.P65Warnings.ca.gov.
mWARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities contains chemicals known [to the State of California] to cause cancer, birth defects, or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specically designed to lter out microscopic particles. For more information go to www.P65Warnings.ca.gov.
Loading...