WARMING PRODUCT
User Manual
Sleep warm. Sleep well.™
P.N. 114473-000
www.sunbeam.com
IMPORT ANT INSTRUCTIONS
DO NOT DESTROY
Warnings and Safeguards
As with all electrical products, misuse of product or failure to properly follow
the instructions may cause overheating, fire, or personal injury. Please read the
product label and all of the instructions before using your warming product.
1. Do not use this warming product with an infant, a child, an incapacitated
person, a paraplegic, a quadriplegic, a diabetic, one insensitive to heat
such as a person with poor blood circulation, or anyone who cannot clearly
understand the instructions and/or operate the controls.
2. Do not use with damaged cords. Damaged cords can lead to fire. Do not
trap, fold, cross, or pinch cords between bed slats, mattress, or springs,
or against walls, footboards, or bed frame.
3. Do not dry clean this warming product. Cleaning liquid may damage the
insulation of the heating element. Improper laundering may cause problems with the heating wire which can lead to fire.
4. Do not pinch, flex, or expose the heating wire to rubbing. A damaged
heating wire may result in possible overheating or fire.
5. Turn off the control for the warming product when not using.
6. Keep control away from an open window.
7. Do not use pins; they may damage the electric wiring.
8. Be sure this blanket/mattress pad/throw is used only on an AC supply
current circuit of 110-120 volts. Do not use with an extension cord.
9. May experience increased heat in areas where warming product is bunched
or folded while in use.
10. Keep all dogs, cats, and other pets away from this warming product.
This is an electrical appliance that they can damage or be injured by.
11. Do not use blanket/mattress pad on a waterbed, sofa, bunk bed, or
mechanically adjustable bed and do not use throw on a waterbed,
bunkbed, or mechanically adjustable bed.
12. Do not use another electronic heating device in conjunction with your
warming product.
13. Use the proper size blanket/mattress pad for your bed. For example, use a
Twin Size warming blanket on a Twin Size bed.
14. If the following Important Instructions are not followed the warming product will not operate properly.
15. If you see the warming product operating improperly, unplug it immediately
and call Sunbeam Consumer Care at 800-892-7684.
1
Control Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pre-Heat & Auto-Off features . . . . . . . . . . . . . . . . . . . 2
Warming Blanket and Mattress Pad
Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warming Throw
Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Frequently asked questions . . . . . . . . . . . . . . . . . . .7-8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
How to obtain warranty service . . . . . . . . . . . . . . . . .10
Table of contents
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions while setting up or using your product,
please visit us on the World Wide Web at: www.sunbeam.com or
contact Sunbeam Consumer Care at: (800) 892-7684.
Welcome
Thank you for choosing a Sunbeam®warming product. With your purchase
you’ve made a real investment in your comfort and can look forward to
staying warm and cozy for many cool days to come.
With over 50 years of experience and over 25 million households using a
Sunbeam®warming product, rest comfortably knowing that you can trust
the Sunbeam®brand for quality and performance.
So get ready for a more restful sleep.
2
Control chart
Style Number
Backlit Display ❂❂❂ ❂
Auto-Off 10 hour 10 hour 10 hour 10 hour 3 hour
Warming Settings 10 20 10 10 10 3 3
Silent Operation ❂❂❂❂❂❂❂
Pre-Heat ❂❂
Easy Operation ❂❂❂❂❂❂❂
Easy Grip ❂❂❂❂ ❂❂❂
Room Temp Compensation ❂
Interchangeable Top ❂
Auto Dimmer ❂
SmartSense™
ChoicePlus™ StyleSmart™ ViewEasy™ EasySet™ SlimStyle™AO SlimStyle™
Pre-Heat & Auto-Off features
Auto-Off Feature for Blanket, Mattress Pad and Throw
(selected models only):
The “Auto-Off” feature is designed for safety and conservation of
energy by automatically turning your blankets or mattress pad off
after 10 hours of continuous use (3 hours for throws).
The “Auto-Off” function engages 10 hours or 3 hours (depending on
the product) after the control is turned “On”.
For Dual Controls: Each control operates independently and will turn off 10 hours or 3 hours
(depending on the product) after the control is turned “On”.
Note: After a power outage, the “Auto-Off” feature automatically resets the timer.
T
o restart all warming products after a power failure:
Press the power button and the warming product will begin to warm.
Pre-heat:
1 To use the preheat feature, simply press the round “On/Off” button and then press the “Preheat” button.
The preheat function will heat the bed for a period of 30 minutes and the control will return to its
previous setting.
2 To reset the preheat feature, simply press the “On/Off” button OFF.
3 To turn back ON repeat step 1.
G85
(Single Control)
G85KQ
(Dual Control)
85P
(Single Control)
85KQP
(Dual Control)
H85
(Single Control)
H85KQ
(Dual Control)
D85P
(Single Control)
D85KQP
(Dual Control)
J85P/J85D
(Single Control)
J85KQP
J85KQD
(Dual Control)
A85AP
Throw
A85P
Throw
For questions or support, please visit: www.sunbeam.com
1 Place the warming blanket/mattress pad on the bed with the label at the
foot of the bed facing upward.
2 Make sure the cord is connected into the module at the bottom of the
warming blanket/mattress pad until the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could
result from a loose connection.
3 Run the control cord on the floor under the bed. Do not sandwich cord
between the mattress and box spring. Avoid any tangling or pinching.
4 Control Placement:
• Dual Control for warming blanket or mattress pad –
place primary control (label on back of control)
on the right side of the bed.
1
3
4
5
2
3
Warming Blanket and Mattress Pad Set Up
CAUTION: Do not plug main power cord into the wall outlet until you have completely
set up your warming product per the instructions.
• Disconnect power cord from wall before detaching control from warming product.
• Always make sure cords are NOT trapped or pinched between bed slats, mattress,
springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the
plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
IMPORTANT
2
1
3
4
5
2
See Control Features on page 4
for your individual control.
If there is a flashing light or
your control displays a flashing
“FF”, see page 8.
For questions or support, please visit: www.sunbeam.com
• Single Control for warming blanket or mattress pad –
the control can be placed on either side of the bed.
5 Plug power cord into a 110-120 volt wall outlet.
Secondary
Control
Power
Cord
Mattress Pad
Cord Connector
Module
run cord
under the bed
Flag Tag
Label
Left Side
Blanket Cord Connector
Module
Label
Left Side
Right Side
Right Side
Primary
Control
Power
Cord
Primary
Control
Flag Tag
run cord
under the bed
4
SmartSense
™
ChoicePlus
™
StyleSmart
™
ViewEasy
™
EasySet
™
Features:
• INTERCHANGEABLE COVERPLATES– Two colors included
• ROOM TEMPERATURE COMPENSATION – Blanket warms up when the room cools down
• DIGITAL CONTROL – with backlit LCD for night time viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS– select your personal comfort level
• SILENT OPERATION– no clicking when adjusting the temperature
• PRE-HEAT– for cozy warmth before bedtime (see page 2)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION– electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
G85
(Single Control)
G85KQ
(Dual Control)
Control Features
Features:
• DIGITAL CONTROL – with backlit LCD for night time viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 20 TEMPERATURE SETTINGS– select your personal comfort level
• SILENT OPERATION– no clicking when adjusting the temperature
• PRE-HEAT– for cozy warmth before bedtime (see page 2)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION– electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
85P
(Single Control)
85KQP
(Dual Control)
Features:
• DIGITAL CONTROL – with backlit LCD for night time viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS– select your personal comfort level
• SILENT OPERATION– no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION– electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
H85
(Single Control)
H85KQ
(Dual Control)
D85P
(Single Control)
D85KQP
(Dual Control)
Features:
• DIGITAL CONTROL – with backlit LCD for night time viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS– select your personal comfort level
• SILENT OPERATION– no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION– electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
Features:
• BACKLIT DIAL – for easy night-time viewing of the warming setting
• 10 TEMPERATURE SETTINGS– select your personal comfort level
• SOLID STATE – for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
• AUTO DIMMER – the lighted dial will automatically dim after 60 seconds
J85P/J85D
(Single Control)
J85KQP/J85KQD
(Dual Control)
Using your Control:
1 To turn the control on, simply press the “On/Off” button.
2 Adjust the warming setting to your personal comfort level.
CAUTION: ALWAYS turn the warming blanket/mattress pad “OFF” when not in use.
3 To turn the warming blanket/mattress pad OFF simply press the “On/Off” button.
For questions or support, please visit: www.sunbeam.com
Using your Control:
1 To turn the control on, simply press the “On/Off” button. The backlit display light will reset itself by flashing “88” and
then will return to the previous setting and will begin to warm.
CAUTION: ALWAYS turn the warming blanket/mattress pad “OFF” when not in use.
2 To turn the warming blanket/mattress pad OFF simply press the “On/Off” button.
5
Control Features
Features:
• 3 TEMPERATURE SETTINGS– select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION– electronic control for easy operation
• EASY GRIP – ergonomic control for easy operation
• AUTO-OFF (SlimStyle AO only) – 3 hour Auto-Off (see page 2)
Using your Warming Throw Control:
1 To turn the throw on simply press the round gray button. The indicator
light will glow, depending on which setting the warming throw is set,
and the warming throw will begin to warm.
CAUTION: ALWAYS turn the warming throw “OFF” and disconnect
the power cord from the outlet when not in use.
2 To turn the warming throw OFF simply press the round gray button
through the different settings until the temperature setting lights are
not glowing.
SlimStyle™AO (Auto-Off)
A85AP
SlimStyle
™
A85P
When setting up your warming throw, be sure to follow the steps below in order.
1 Locate the warming throw’s information label near the module.
2 Make sure the cord is connected into the module at the bottom of the
warming throw until the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result
from a loose connection.
Warming Throw Set Up
For questions or support, please visit: www.sunbeam.com
2
1
3
3 Plug the warming throw power cord into a 110-120 volt wall outlet.
CAUTION: Do not plug main power cord into the wall outlet until you have completely
set up your warming product per the instructions.
• Disconnect power cord from wall before detaching control from warming product.
• Always make sure cords are NOT trapped or pinched between bed slats, mattress,
springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If
the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
IMPORTANT
2
If there is a flashing light on
your control, see page 8.
Flag Tag
Power
Cord
Module
Throw Cord
Connector
Control
Label
Throw Cord
6
We recommend washing before initial use.
Before washing or storing your warming product:
1 Disconnect power cord from wall BEFORE detaching control cord from the warming product.
2 Ensure that no cords are still connected and none of the wires have worn through the fabric.
3 Carefully follow all washing instructions or your warming product may shrink and possibly
cause a fire hazard.
• DO NOT submerge control in water
• DO NOT dry clean your warming product. Dry cleaning solvents may damage the wires.
• DO NOT use bleach or cleaning fluids.
• DO NOT use a wringer.
• DO NOT iron your warming product.
• DO NOT use mothballs or sprays of any kind.
• DO NOT reconnect the warming product or use it until it is COMPLETELY dry.
• DO NOT wash or put into water the power cord or any of the product’s cords.
Taking care of your warming product is easy and safe as long as you follow a few simple steps.
Machine Washing
1 Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water.
2 Wash in mild soap and lukewarm water on the “delicate” or “gentle” cycle in the washer
for two minutes. Remember, do not use bleach.
3 Rinse in fresh, lukewarm water.
4 Spin dry in the washing machine. Then gently stretch to its original size.
Machine Drying
Caution: Do not use commercial dryers or the dryers at your local laundromat.
They get too hot and would damage the wiring of the warming product.
1 Preheat the dryer on the “low” temperature setting for 2 minutes.
2 Place blanket/mattress pad/throw into the dryer and tumble dry for 10 minutes at a low temperature.
3 Remove the blanket/mattress pad/throw while it is still damp and gently stretch it to its original size.
4 Drape the warming product over a clothesline or a shower rod. DO NOT use clothespins.
5 Warming product must be completely dry before reconnecting the power plug or control plug.
Hand Washing
1 Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water.
2 Gently squeeze the soap suds through a few times.
3 Rinse in fresh, lukewarm water.
Hand Drying
1 Gently stretch the blanket/mattress pad/throw back to its original size.
2 Drape the warming product over a clothesline or hang over a shower rod. DO NOT use clothespins.
3 Warming product must be completely dry before reconnecting the power plug or control plug.
Care and cleaning OF YOUR WARMING PRODUCT
For questions or support, please visit: www.sunbeam.com
Q Who should NOT use the warming blanket, warming mattress pad, or warming throw?
A The following people should NOT use the warming blanket, warming mattress pad,
or warming throw:
• An infant
• A child
• An incapacitated person
• A paraplegic
• A quadriplegic
• A diabetic
• Anyone insensitive to heat such as a person with poor blood circulation
• Anyone who cannot clearly understand the instructions and/or operate the controls
Q What do the Underwriters Laboratories (UL) or (ETL) labels mean? What do either of these
labels mean about safety of Sunbeam warming products?
A Underwriters Laboratories (UL) develops product safety standards for a large range of
products and performs independent tests based on these standards. Products tested by UL
and which have passed all the safety standards are permitted to bear the UL label. Intertek
Testing Services (ETL) is a certified, independent testing organization that tests products in
accordance with UL safety standards and issues the ETL label for those products that meet
the relevant UL standards. All Sunbeam products are tested to UL standards and bear either
the UL or ETL label to indicate that the product meets or exceeds UL/ETL safety standards for
warming products.
Q I have heard that some warming products have Electromagnetic Fields (EMFs).
What is this?
A EMF stands for Electromagnetic Field. This is an electrical field that surrounds any wire
that has current flowing along its length. Although several studies have been conducted to
evaluate the impact, EMFs have not been proven to be harmful. In any event, Sunbeam has
reduced the strength of EMFs in its blankets/mattress pads/throws to very low levels.
Q What do I do if my pet chews the cord, I lose my control, or the control does not operate
properly?
A Please stop using the warming product immediately. Call our Consumer Service number
listed under How to Obtain Warranty Service and ask for instructions on how and where to
send the warming product.
Q My control feels warm to the touch. Is this a problem?
A No. The control will feel warm to the touch when functioning properly.
7
Frequently asked questions OF YOUR WARMING PRODUCT
For questions or support, please visit: www.sunbeam.com
(FAQ’scontinued on next page)
8
For questions or support, please visit: www.sunbeam.com
Q My warming blanket/warming mattress pad/warming throw doesn’t heat properly.
A Your warming product is not a heating pad. It will not feel hot to the touch when laid out
flat in a normal manner. Try the following fold test to see if it is operating properly.
1 Fold the warming blanket, warming mattress pad, or warming throw 3 times over.
2 Make sure the control cord is connected to the module and then
plug the power cord into an outlet.
3 Turn on your warming product, then turn the control to the highest
setting and wait five to seven minutes.
4 Put your hand between the folds and you should feel the blanket/
mattress pad/throw warming.
Caution: Do not continue the test for more than seven minutes. DO NOT
attempt to make any internal adjustments to this appliance. If you have tried all of the solutions above and the warming product still doesn’t work, stop using it immediately, disconnect
the power cord and contact Sunbeam Consumer Care.
Q What does “FF” mean on my Electronic Digital Control?
A The digital controls are designed to notify you in the event that a problem has been
discovered by flashing “FF” on the display. Follow instructions on the flag tag to reset
control. First, check the blanket/mattress pad for visual damage. If no visual damage is
found, unplug the system from wall outlet. Check that the control is well
connected to the module. Plug the power cord into the wall outlet. Set the
control to “On.” If the system still does not operate after 2 or 3 times
trying to reset, disconnect the power cord and contact Sunbeam Consumer
Care.
Q What does a flashing light mean on my EasySet™, SlimStyle™ AO or
SlimStyle™ control ?
A These controls are designed to notify you in the event that a problem has
been discovered by flashing the light on the control. Follow instructions on
the flag tag to reset control. First, check the warming product for visual damage. If no
visual damage is found, unplug the system from wall outlet. Check that the control is well
connected to the module. Plug the power cord into the wall outlet and turn the control On.
If the product still does not operate after 2 or 3 times trying to reset, disconnect the power
cord and contact Sunbeam Consumer Care.
FF
Models:
ViewEasy,
ChoicePlus,
StyleSmart,
SmartSense
9
Sunbeam Products Inc. (“Sunbeam”) warrants that for a period stated below from the date of
purchase, this product will be free from defects in material and workmanship.
• All warming products branded Arlington™ will carry a ONE year limited warranty.
• All warming products branded Sunbeam®HomeChoice™, SlumberRest®Cuddler™, and
Cuddle Up®will carry a TWO year limited warranty.
• All other warming products branded Sunbeam® andSlumberRest® will carry a FIVE year limited warranty.
Sunbeam, at its option, will repair or replace this product or any component of the product
found to be defective during the warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is no longer available, replacement may
be made with a similar product of equal or greater value. This is your exclusive warranty. This
warranty is valid for the original retail purchaser from the date of initial retail purchase and
is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain
warranty performance. Sunbeam dealers, service centers, or retail stores selling Sunbeam
products do not have the right to alter, modify, or any way change the terms and conditions of
this warranty. This warranty does not cover normal wear of parts or damage resulting from
any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone
other than Sunbeam or an authorized service center. Further, the warranty does not cover Acts
of God, or Nature, such as fire, flood, hurricanes and tornadoes. Sunbeam shall not be liable
for any incidental or consequential damages caused by the breach of any express or implied
warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the
above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages or limitations on how long an implied warranty lasts,
so the above limitations or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from state to state.
Limited Warranty
10
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
How to obtain warranty service:
We’re Here to Help. For any questions you may have about your warming
product, please visit our web site at: www.sunbeam.com or contact
Sunbeam Consumer Care: 1-800-892-7684.
©2004 Sunbeam Products, Inc. All rights reserved. Sunbeam®, Cuddle Up® and
SlumberRest® are registered trademarks and Arlington™, HomeChoice™,
SmartSense™, ChoicePlus™, Style Smart™, ViewEasy™, EasySet™, SlimStyle™
and Cuddler™ are trademarks of Sunbeam Products, Inc., Boca Raton, FL 33431
Distributed by Sunbeam Products, Inc.
Printed in U.S.A.
Loading...