Sunbeam GL8200 User Manual
Gelateria
Automatic Ice-Cream Maker
Instruction Booklet
GL8200
Please read these instructions carefully
and retain for future reference.
Contents
Important instructions – retain for
future use.
Sunbeam’s Safety Precautions 1
Features of your Gelateria 2
Before using your Gelateria 5
Using your Gelateria 6
Handy Hints 9
Tips to making custard based ice-cream 10
Care and Cleaning 11
Recipes 12
SAFETY PRECAUTIONS FOR YOUR
SUNBEAM GELATERIA, AUTOMATIC
ICE-CREAM MAKER.
• Do not immerse the paddle motor in water or
any other liquid.
• Always operate on a flat surface.
• Always store the Ice-Cream Maker in an upright
position.
• Ensure that the ventilation slots on either side
of the appliance are not obstructed.
Sunbeam are very safety conscious when
designing and manufacturing consumer
products, but it is essential that the product
user also exercise care when using an
electrical appliance. Listed below are
precautions which are essential for the safe
use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug – do not pull the cord.
• Turn the power off and remove the plug
when the appliance is not in use or before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked and
tested by a qualified technician or service
person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked on
the appliance.
• Close supervision is necessary when your
appliance is being used near children or by
infirm persons.
• Never leave an appliance unattended while
in use.
• Young children should be supervised to
ensure that they do not play with the
appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place appliance on or near a hot gas
flame, electric element or on a heated oven.
Do not place on top of any other appliance.
• Do not let the power cord of an appliance
hang over the edge of a table or bench or
touch any hot surface.
• For safety reasons and to avoid maintenance
by unskilled persons, some appliances are
‘sealed’ using tamperproof screws. Such
appliances should always be returned to the
nearest Sunbeam Appointed Service Centre
for adjustment or repair if required.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been dropped or damaged in any manner. If
damage is suspected, return the appliance
to the nearest Sunbeam appointed Service
Centre for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water or
any other liquid unless recommended.
1
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Sunbeam’s Safety Precautions
Features of your Gelateria
Transparent lid with pouring hole
Enables easy pouring of ingredients during
the mixing process and its transparency
allows observation of the ice-cream making
process.
Removable cylinder
This 1 Litre metal cylinder with carry handle
is easily removed from the appliance for the
serving of frozen desserts and a quick clean
up.
Paddle
The specially designed paddle guarantees
perfect aeration throughout the ice-cream
mixture, ensuring a deliciously creamy result
every time.
2
Paddle motor On/Off
Will start the churning of mixture inside the
cylinder, when used in conjunction with the
LED timer.
Chiller On/Off
The appliance is pre-chilled for 5 minutes
to ensure freezing temperatures as low as
-30°C are reached during the churning
process. This is possible due to an internal
compressor which creates the perfect freezing
environment to make frozen desserts at a
moments notice, eliminating the need to prefreeze canisters overnight. The indicator light
shows that the chilling system is operating.
LED timer display
Release button
Pressing the Release button enables the
paddle motor with transparent lid to be
removed from the appliance.
3
4
Features of your Gelateria (continued)
LED timer display
Set time - The preselected time for churning
a mixture is displayed on the left side of the
panel in red and remains constant throughout
the churning process. This set time can be
increased with increments of 5 minutes until
a maximum of 60 minutes is reached. In the
event that additional time is required above
60 minutes, the appliance will reset to 5
minutes. Set time will flash to indicate that
the timer has not yet started.
Remaining time - the remaining time for
churning a mixture is displayed on the right
side of the panel in green and will decline
by 1 minute. When minutes is reached,
the timer will flash and beep for 5 counts,
indicating that the churning will finish in 2
minutes. When the timer has reached the
set churning time, the remaining time will
display and the timer will beep for 18
counts.
Start/Stop - Pressing the Start button will
commence the timer and rotation of the
paddle. Alternatively, whilst the appliance is
operating, pressing the Stop button will stop
the timer as well as the paddle. Additionally,
pressing the Stop button will cancel the
beeping notice of the timer, if desired.
Timer Select - Allows you to select the time
necessary to make a particular frozen dessert,
with 5 minute increments up to 60 minutes.
When this time is reached, the paddle motor
will switch off automatically and beep for 18
counts.
5
HeadingBefore using your Gelateria
Important: Place the Gelateria upright on
a flat surface for at least 12 hours before
using it for the first time, to allow the oil
contained in the compressor to settle. The
same procedure should be followed in the
event that the ice-cream maker has been
accidentally placed in a non-upright position.
1. Before use, thoroughly wash all parts
that will come into contact with the icecream. The fixed stainless steel cylinder
should be cleaned using a damp cloth and
dried thoroughly. The removable cylinder,
transparent lid with pouring hole and
paddle should be washed in warm soapy
water, rinsed and dried thoroughly.
2. When your Ice-Cream Maker is first used,
you may experience an odour and possibly
a slight wisp of smoke from the appliance.
This is released by the insulation material
of the motor when the appliance is heated,
which protects the motor and is a normal
occurrence. After the first few uses, this
will no longer occur.
HeadingUsing your Gelateria
1. Position the Ice-Cream Maker on a dry,
level surface, ensuring that the ventilation
slots on either side of the appliance are not
obstructed.
2. Ensure your Ice-Cream Maker is unplugged
from the power outlet before fitting the
connecting parts.
3. Pour a solution of salt and water into
the fixed stainless steel cylinder, using 1
tablespoon (20ml) water and a teaspoon
(5g) salt.
NOTE: The salt solution is recommended in
order to facilitate the transfer of freezing
temperatures from the fixed cylinder to
the removable cylinder and guarantee the
success of the frozen dessert.
4. Insert the removable cylinder inside the
fixed stainless steel cylinder. Be sure
to position the handle of the removable
cylinder in between the locking tab to
prevent the cylinder from moving during
the churning process. See figure 1.
5. Attach the transparent lid with pouring
hole to the base of the paddle motor, using
the round cutout in the centre of both
parts to align correctly. Connect these two
parts together by rotating the plastic screw
in an anti-clockwise direction until firm.
See figure 2.
6. Insert the paddle into the opening at the
base of the paddle motor. See figure 3.
7. Position the paddle motor with paddle over
the cylinder and rotate clockwise until the
connection plug of the paddle motor locks
into the adjacent socket. See figure 4.
Figure 2
Figure 3
6
Figure 1
Locking
Tab
Loading...