4040-026
User
Manual
EURO P
RESS
™
IRON
Model 4040-026
IMPORTANT SAFEGUARDS
When using your iron, basic safety precautions should
always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USE.
• Use iron only for its intended use.
• To protect against risk of electric shock, do not
immerse the iron in water or other liquids.
• The iron should always be turned to “OFF”
before plugging or unplugging from outlet.
Never yank cord to disconnect from outlet;
instead, grasp plug and pull to disconnect.
• Do not allow cord to touch hot surfaces.
Let iron cool completely before putting away.
Loop cord loosely around iron when storing.
• Always disconnect iron from electrical outlet
when filling with water or emptying and
when not in use.
safety
• Do not operate iron with a damaged cord or
if the iron has been dropped or damaged.
To avoid the risk of electric shock, do not
disassemble the iron. Take it to an authorized
service center for examination and/or repair.
Incorrect reassembly can cause a risk of electric
shock when the iron is used.
• Close supervision is necessary for any appliance
being used by or near children. Do not leave
iron unattended while connected or on an
ironing board.
• Burns can occur from touching hot metal parts,
hot water or steam. Use caution when you
turn a steam iron upside down – there may
be hot water in the reservoir.
ii
• If the iron is not operating normally, disconnect
from the power supply and have the iron
serviced by an authorized service center.
• Your SUNBEAM®iron is designed to rest on
the heel rest. Do not leave the iron unattended.
Do not set the iron on an unprotected surface,
even if it is on its heel rest.
• This is a 1400-Watt appliance.*To avoid
a circuit overload, do not operate another
high wattage appliance on the same circuit.
• If an extension cord is absolutely necessary,
a 15-ampere cord should be used.
Cords rated for less amperage may overheat.
Care should be taken to arrange the cord
so that it cannot be pulled or tripped over.
For products purchased in the United States
and Canada only
To reduce the risk of electrical shock, this appliance
has a polarized plug (one blade is wider than the
other). This plug fits a polarized outlet only one
way; if the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat
this safety feature.
SAVE THESE
INSTRUCTIONS
safety
SPECIAL INSTRUCTIONS
iii
Table of Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Learning About Your Iron. . . . . . . . . . . . . . . . . . . . . . . . . 4
Filling the Water Reservoir . . . . . . . . . . . . . . . . . . . 5
Ironing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dry Ironing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Steam Ironing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using the Iron’s Special Features . . . . . . . . . . . . . . . . . . 7
SHOT OF STEAM
Vertical Steam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Patented MOTION SMARTTMAuto-Off. . . . . . . . . . 9
Caring for Your Iron After Use. . . . . . . . . . . . . . . . . . . . 10
Turning Off Your Iron . . . . . . . . . . . . . . . . . . . . . . . 10
contents
®
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Storing Your Iron . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintaining Your Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning the Soleplate . . . . . . . . . . . . . . . . . . . . . . 11
Using the Self-Cleaning Feature . . . . . . . . . . . . . . 11
Ironing Tips and Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ironing Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ironing Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
How to Obtain Warranty Service . . . . . . . . . . . . . 16
2
welcome
Congratulations on your purchase of a SUNBEAM
®
Iron!
Sunbeam has designed your iron to provide
the utmost in quality, ease of use and convenience.
This EURO PRESS™SUNBEAM®iron offers the following
features:
• Non-Stick Surface – Prevents starch residue and
fabrics from sticking to the bottom, making the
iron easier to clean.
• 360° Tangle-Free Cord – Keeps the power cord
off of the fabric and out of your way, whether
you are right or left handed.
• Self-Cleaning – Prevents mineral build up
that can reduce the life of your iron.
• Large Water Fill Hole – Allows you to fill the
water reservoir faster while reducing water
spills and drips.
• Accepts Tap Water – Eliminates the necessity of
keeping distilled water on hand for ironing.
• Patented MOTION SMARTTMAuto-Off – Automatically
turns the iron off if it is not moved after
15 minutes in the upright position or after
30 seconds in the ironing position.
• Power Indicator Light – Lights steadily to let you
know the iron is
plugged in; blinks to let you know
that the patented MOTION SMARTTMAuto-Off has
activated; and is unlit when the iron is unplugged.
• Vertical Steam – Functions like a garment steamer
to remove wrinkles from hung garments or drapes.
• SHOT OF STEAM®– Offers a powerful burst of
steam for removing
Welcome
3
0
your iron
0
Learning About Your E
1. Water Fill Hole
2. SHOT OF STEAM®Button
3. Steam Dial
4. Power Indicator Light
5. Patented MOTION SMARTTMAuto-Off Indicator Blinking Light
6. 360° Tangle-Free Swivel Cord
7. Fabric Select Dial
8. See-Through Water Reservoir
9. Non-Stick Soleplate
10. Cord Wrap
URO PRESS
™
Iron
4
3
2
1
5
6
7
8
10
9
4
your iron
Filling the Water Reservoir
You must fill the water reservoir with water to use
the SHOT OF STEAM®feature and to get steam
out of your iron.
Tip: SUNBEAM®tests each iron at the factory to
ensure that they function correctly. The test may
leave a small, harmless amount of water within
the water reservoir.
Before you fill the water reservoir, please consider
the following:
• While this iron was designed for use with tap
water, very hard water will reduce the performance
of the iron. If your water is very hard, SUNBEAM
®
recommends that you use tap water the first time,
then consider using demineralized or distilled water
for subsequent use. You should use tap water once
a month, however, to maintain the iron’s optimal
steam performance.
• Do not use water that has passed through a home
water softening system. This type of water contains
minerals that will decrease the performance and
shorten the life of your iron. Use demineralized
or distilled water, instead.
Important: When not ironing, always set the Steam
Dial to ZERO and the Fabric Select Dial to MIN.
To fill the water reservoir:
1. Make sure the iron is unplugged. Set the Steam
Dial to ZERO and the Fabric Select Dial to MIN.
2. Fill water cup with water. Pour water into iron
water reservoir. Do not fill water reservoir
beyond maximum fill level.
W
ARNING
:
To prevent the risk of burns, be careful
when filling a hot iron with water.
Hot metal parts, hot water and
steam can cause injuries.
5
0
0
Ironing
ironing
Dry Ironing
1. Make sure that the Steam Dial is set to ZERO.
2. Plug the cord into a 120 volt AC outlet.
The Power Indicator will light.
3. Turn the Fabric Select Dial to the dry ironing
fabric setting you desire and allow the iron to
heat for 2 minutes. While the iron is heating,
make sure it is sitting on its heel rest on a
stable, protected surface.
Tip: Refer to the Ironing Guide on Page 15
for the recommended setting for your fabric.
Steam Ironing
1. Follow the instructions for “Filling
the Water Reservoir” on Page 5.
0
2. Plug the cord into a 120 volt AC outlet.
The Power Indicator will light.
3. Turn the Fabric Select Dial to the steam ironing
fabric setting you desire
or Silk)
While the iron is heating, make sure it is sitting
on its heel rest on a stable, protected surface.
Tip: Refer to the Ironing Guide on Page 15
for the recommended setting for your fabric.
4. After the iron has heated (2 minutes), turn
the Steam Dial to desired steam setting.
6
and allow the iron to heat for 2 minutes.
(Linen, Cotton, Wool
features
Using the Iron’s Special Features
SHOT OF STEAM
®
The SHOT OF STEAM®feature provides an extra
burst of steam for deep penetration of stubborn
wrinkles. You can use this feature while Dry or
Steam ironing, but the water reservoir must be
at least 1/4 full of water.
To use the SHOT OF STEAM®feature:
Place the iron on top of the wrinkle and
press the SHOT OF STEAM®button each
time you would like an extra burst of steam.
The SHOT OF STEAM®feature may be used
continuously with just a short pause between shots.
7
Ironing
features
Vertical Steam
The vertical steam feature allows your iron
to function as a garment steamer.
Tip: When using the vertical steam on clothing,
hang the clothing on a clothes hanger for best
results. Hanging curtains and drapes may also
be steamed.
To use the Vertical Steam:
1. Make sure that the iron has heated up
(2 minutes).
2. Hold the iron in a vertical position, with the
iron close to but not touching the fabric
you want to steam.
3. With your other hand, pull the fabric tight.
4. Press the SHOT OF STEAM®button at
approximately 3-second intervals as you
move the iron across the wrinkled area.
WARNING: To prevent the risk of burns, keep
your hand away from the area being steamed.
WARNING: DO NOT steam garments while
wearing them; this may result in injuries.
8
features
Patented MOTION SMARTTMAuto-Off
When the iron is plugged in, the Power Indicator
will light steadily, indicating that there is power
to the iron.
If you leave the iron:
• in a vertical position (on its heel rest) without
moving it, the iron will automatically turn off
after 15 minutes. The Power Indicator will
blink to let you know that the iron has
stopped heating.
•in a horizontal position without moving it,
the iron will automatically stop heating after
30 seconds. The Power Indicator will blink to
let you know that the iron has stopped heating.
Important: The Power Indicator will continue
to blink until the iron is unplugged.
To restart the iron:
Move the iron back and forth and allow it to
reheat for 2 minutes. The indicator will stop
blinking and the iron will start heating again.
WARNING: The patented MOTION SMARTTMAuto-Off
is a safety feature, not a recommended means for
turning your iron off. See “Caring for Your Iron After
Use”
on Page 11, for information on turning off your
iron and storing it safely between use.
9
Caring for Your Iron After Use
after use
Turning Off Your Iron
1. Turn the Steam Dial to ZERO and Fabric Select
Dial to MIN.
2. Unplug the iron from the power source.
WARNING: NEVER yank the power cord when
unplugging the iron, this can damage the cord.
Storing Your Iron
1. Allow the iron to cool.
2. If you do not use your iron on a daily basis,
empty the water reservoir after each use for
a longer iron life. To do so, turn the iron upside
down to allow water to flow from the fill hole.
Shake the iron gently to remove trapped
water drops.
3. Loosely loop the power cord around the cord
wrap and store the iron on its heel rest.
Important: Wrapping the cord around the iron
too tightly can damage the cord.
0
Tip: When not ironing, always set the Steam Dial
to ZERO and the Fabric Select Dial to MIN.
10
0
Loading...