Sunbeam 400 User Manual

Oskar 400

Continuous Flow Food Processor

LC2700

Hero of Oskar 400

INSTRUCTION AND RECIPE BOOKLET

Sunbeam’s Safety Precautions.

Sunbeam are very safety conscious when designing and manufacturing consumer products, but it is essential that the product user also exercise care when using an electrical appliance. Listed below are precautions which are essential for the safe use of an electrical appliance:

• Read carefully and save all the instructions provided with an appliance.

• Always turn the power off at the power outlet before you remove a plug. Remove by grasping the plug - do not pull on the cord.

• Turn the power off and remove the plug when the appliance is not in use and before cleaning.

• Do not use your appliance with an extension cord unless this cord has been checked and tested by your electricity supplier or qualified technician.

• Always use your appliance from a power outlet of the voltage (A.C. only) marked on the underside of the appliance.

• Close supervision is necessary when your appliance is being used near children or infirm persons.

• Never leave an appliance unattended while in use.

• Young children or infirm persons should be supervised to ensure that they do not play with the appliance.

• Do not use an appliance for any purpose other than its intended use.

• Do not place an appliance on or near a hot gas flame, electric element or in a heated oven. Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang over the edge of a table or bench top or touch any hot surface.

• Do not immerse in water.

• For safety reasons and to avoid maintenance by unskilled persons, some appliances are ‘sealed’ using tamperproof means as specified by S.A.A. (Standards Association of Australia). Such appliances should always be returned to the nearest Service Centre for adjustment or repair if required.

• Do not operate any electrical appliance with a damaged cord or after the appliance has been dropped or damaged in any manner; If damage is suspected, return the appliance to the nearest Service Centre for examination, repair or adjustment. As a service to Customers, Service Centres will carry out a free check on your appliance to ensure it is electrically safe.

• For additional protection Sunbeam recommend the use of a residual current device (RCD) with a tripping current not exceeding 30mA in the electrical circuit supplying the power outlet in use.

• Blade and Processing Disc are very sharp, handle with care when removing, replacing or cleaning.

• Ensure fingers are kept well away from the Processing Blade and the Slicing/Shredding Disc when in use.

• Use the food processor on a dry, flat level surface.

• Never place Processing Blade on the Base without first putting the Container properly in place.

• Be certain, Container Cover is securely locked in place while operating appliance.

• Never feed food by hand, always use Food Pusher.

• Never use the food processor outdoors.

• Never remove the Cover or Processor until the Blade or Disc has come to a complete stop and the unit has been unplugged from a power outlet.

If you have any concerns regarding the performance and use of your appliance, please ring our Toll Free number (Australia only) 1800 025 059. New Zealand - contact the Sunbeam Office in Auckland.

Ensure the above safety precautions are understood.

SAFETY PRECAUTIONS FOR ALL ELECTRICAL APPLIANCES

SAFETY PRECAUTIONS FOR YOUR FOOD PROCESSOR.

Features of you Sunbeam Oskar 400.

Feed pusher

Feed tube

Continuous flow attachment

Ejector disc Reversible

slicing/shredding disc

Processing blade

Processing cover

Processing bowl

Non-slip feet

Features of you Sunbeam Oskar 400 (cont).

1. Powerful 400 watt motor

The base houses a powerful 400 watt motor, ideal even under heavy loads. Perfect for performing food preparation tasks including

- chopping, mincing, pureeing, blending, mixing, shredding and slicing - quickly and efficiently.

2. Processing Bowl

The processing bowl locks into place on the motor base. The shape, in combination with the design of the blade, ensures even, efficient processing. The transparency of the processing bowl allows you to check the food during processing and for additional convenience, the processing bowl is microwave safe and dishwasher safe.

3. Processing blade

The stainless steel processing blade is contoured to fit the rounded shape of the processing bowl to provide a most efficient chopping/mixing action.

The processing blade is only to be used in the processing bowl.

4. Cover

The transparent cover is the lid for the processing bowl and activates the automatic On/Off interlock switch system. The cover also has a pouring hole, so ingredients can be added gradually during processing.

Features of you Sunbeam Oskar 400 (cont).

7. Continuous Flow attachment

This attachment locks onto the processing bowl in a similar manner to that of the processing bowl cover, and activates the automatic On/Off interlock switch system. The continuous flow attachment allows you to slice or shred unlimited amounts of food. A large bowl or suitable container is required to collect the processed food.

6. Reversible Slicing/Shredding disc

The easy clean stainless steel disc is reversible

- one side will Slice and the other side will Shred. The disc is only suitable when using the continuous flow attachment.

5. Ejector Disc

When using the Slicing/Shredding disc the ejector disc must first be placed over the drive shaft. As the food is sliced or shredded, it is thrown from the ejector disc, through the continuous flow attachment and into a waiting bowl on the side of the unit.

8. Food pusher

The food pusher is used with the continuous flow attachment. It guides food evenly down the feed tube and onto the Slicing/Shredding disc.

Before using your Oskar 400

• Wash the processing bowl, cover, continuous flow attachment and all attachments in warm to hot water using a mild detergent. Dry each part thoroughly before use.

• Before you assemble the Oskar 400, ensure that the power cord in unplugged.

Using the processing bowl and cover

1. Set up the motor base facing you on a dry, level surface.

Note: The tallest side of the motor housing to the rear.

2. Place the processing bowl over the drive shaft and rotate the container until it drops down evenly onto the base. Turn the processing bowl anti-clockwise firmly until it ‘locks’ into place (1).

3. Fit the processing blade onto the drive shaft,

rotating it slightly until it settles into place (2).

4. Place food in the food processor bowl.

5. Place the processing bowl cover on the processing bowl so that the large locking tab on the cover is to the right side of the bowl, near the horizontal slot at the back of the processing body (3).

6. Plug in the food processor and turn the power ‘ON”.

7. Turn the processing cover to the left (anticlockwise), this will engage the automatic switch and the food processor will turn on (4).

Note: Unless the locking tab on the processing bowl cover is engaged, the unit will not turn on.

Using your Sunbeam Oskar 400.

(1)

(2)

(3)

(4)

Large locking tab

Horizontal slot

+ 13 hidden pages