w
MODEL 2571
OWNER’S
MANUAL
CAUTION:
READ AND
SAVE THESE
INSTRUCTIONS.
900 AIR CLEANER
AND
OPERATING INSTRUCTIONS
IONIZER
Any questions or comments?
Call
I-800-526-2832
Mon.-Fri. 8 a.m.
4 p.m. Centrai Time
-
INTRODUCTION
LOCATION
Your Sunbeam 900 Air Cleaner has been designed to
let
you
enjoy a refreshing experience in
living.
Airborne particles are removed from air passing
through the unit by the process of electrostatic
tation and an activated charcoal
NOTE:
This
owner’s manual should be read
roughly before your air cleaner
Retain your owner’s manual for future
ence.
filter.
clean
air
precipi-
tho-
is
operated.
refer-
Remove the plastic bag covering your air cleaner.
Select the location for your air cleaner with electrical
outlet nearby.
power to your air cleaner.
must be
front grill and out of the top grill. (Figure 1) Never place
your air cleaner on soft surfaces (such as beds, sofas
or
(such as stove tops, ovens, etc.).
OPERATION
HOW THE SUNBEAM 900 AIR CLEANER
AND IONIZER WORKS
The air
of air pollution. Some of the pollutants (dust, smoke
and lint) are visible to the naked eye, but
pollutants (pollen and bacteria, to name a few) are
microscopic in size.
Polluted air enters the air cleaner through the front of
the air cleaner. (Figure 1) As shown in Figure 2, the fan
pulls in dirty air and the
cles
pollen) in the dirty air receive a positive electrical
charge as they pass through the ionizing section.
The positively charged particles then enter the
ing section
charged
ticles.
remain there through natural adhesion until removed
by the washing process. The air then passes through a
charcoal
Next, the negative ion generator (#5) freshens stale air.
Finally, electronically cleaned air passes
room through the top grill. (Figure 1)
around
(hair, lint, etc.). The smaller particles (dust, smoke,
It works Ii ke a powerful magnet and the particles
you is filled with thousands of particles
most
Pre-Filter (#l)
(#3)
which uses a series of alternately
aluminum plates to
filter
(#4) that helps remove household odors.
attract
traps large parti-
and retain the par-
back
of the
(#2)
collect-
into the
Plug the cord into
outlet. (See data label on bottom of your air cleaner for
electrical specifications and power
Turn the unit on by sliding the ON/OFF switch to the
desired speed. (DAILY USE, MEDIUM or SUPER
CLEAN, Figure 3) Until your air cleaner is adequately
broken in, the speed should be set on SUPER CLEAN
for 1 minute initially before switching to desired speed.
Your electronic air cleaner is designed for
operation
cleaner remains on constantly. For best results,
“DAILY USE” setting.
The “FAN ONLY” speed is provided to assist in the dry
cycle after cleaning the
NOTE:
Do not use an extension cord to supply
Remember, the air cleaner
placed
carpet),
You may
Sharp
This is a normal occurrence called “arcing”
and results as large particles of dust are
collected
prolonged or continuous arcing occur, the
Electronic Collecting Cell should be
ly cleaned and dried. (See “T
Collecting
SO that air
near computers or next to sources of heat
any
-- peak efficiency is obtained when the air
notice an occasional, infrequent
snapping sound coming from your unit.
in the ionizing-collecting cell. Should
Cell”.)
can
freely circulate into the
_“.
standard household electrical
consumption.)
cell.
O
Clean Electronic
-.
“_-I-._
continuous
Select
thorough-
Figure 1
Figure 2
k
Figure 3
CARE OF CABINET
The outside of the cabinet can be cleaned by using a
Never
soft, clean, damp cloth.
water.
immerse the unit in
TO REMOVE ELECTRONIC COLLECTING
CELL FOR CLEANING
The Electronic Collecting
about every four to eight weeks when your air cleaner
is in constant use.
Turn off the air cleaner and unplug it trom the electrical power source.
Remove cabinet lid by depressing tab located under
lid overhang. (See Figure 11 for exact tab placement)
Slide lid forward from base and
Push
Cell
Locking
while lifting
handles on top of the
Slide Pre-Filter upward from the front of the
ure 7) and remove.
Slide Charcoal
(Figure 6) and remove.
Cell out
Latch
of the cabinet using the two small
Cell.
Filter
upward from
Cell Will
(Figure 5) away from
(Figure 5 & Figure 6)
need cleaning
lift
off. (Figure 4)
back
of the
Cell
Cell
(Fig-
Cell
Figure 5
Figure
8
Figure 4
7
Figure
Figure
5
REPLACEMENT OF CHARCOAL FILTER
ACTIVATED CHARCOAL
HOUSEHOLD ODORS
Washing the Charcoal
destroy its ability to adsorb odor.
Odor adsorption effectiveness
rate and the Charcoal
three months. These filters are available in your
store or through a reorder form enclosed with this unit.
FILTER
Filter
with soap and water
Filter
should be
HELPS REMOVE
Will
gradually deterio-
replaced
Will
every
retail
2
TO CLEAN ELECTRONIC COLLECTING CELL
NOTE: When handling the collecting cell, care should
be taken to avoid damaging wires and metal
plates.
wash Electronic Collecting Cell in dishwasher.
Slide out Pre-Filter located on front of the Cell. Rinse
thoroughly with clean warm water. Set aside to dry.
Use dishwashing detergent and the hottest water
available to make a good soaking solution.
NOTE:
Completely immerse the Cell and soak for 20 to 30
minutes.
After the Cell has soaked sufficiently, it should be
shaken vigorously in water until clean. (Figure 9)
Thoroughly rinse both sides of the cell. If a sprayer is
available, spray with water. (Figure 10) Check to make
sure the cell plates are clean. Carefully wipe with a
Q-tip and alcohol along the ionizing wires.
Repeat the above last 3 paragraphs if necessary.
If the Cell is extremely dirty, spray the cell with
a household cleaning agent such as 409, Fantastik or Lysol. Let the cell
before proceeding to washing instructions.
Do not wash Charcoal Filter. Do not
soak five
(5) minutes
.
Shake as much water out of the cell as possible.
Replace Cell in the unit as described below and oper-
ate unit in “FAN ONLY” position for a minimum of one
hour to insure cell is thoroughly dry.
TO CLEAN NEGATIVE
ION GENERATOR NEEDLE
Make sure the air cleaner is turned off and unplugged
from the electric power source for approximately 1
minute before cleaning needle.
The negative ion generator needle is located in the
right rear of the air cleaner (Figure 11) and should be
cleaned at least every 60 days.
Simply use cotton swab dipped in alcohol and wipe off
the dirt from the needle. Using a dry cotton swab, make
sure the needle is dry.
Figure 9
Figure 10
Figure 11
TO REPLACE ELECTRONIC COLLECTING
CELL AFTER CLEANING
NOTE: Use directions on top of Cell for proper place-
ment of the filters into the Cell and for replacing
the Cell into the unit. Unit will not operate
properly if the Cell is not replaced correctly.
Slide the Pre-Filter in the slots provided in the front of
the Cell. (Figure 12)
Slide the Charcoal Filter in the slots provided in the
back of the Cell. (Figure 13)
14),
Using the cell handles (Figure
the ribs (Figure 14) on the inside cabinet wall. Gently
slide Cell into place.
3
align the Cell with
TO REPLACE CABINET TOP
s/
Figure 12
Figure 13
_ PRE-FILTER
Replace the cabinet top by positioning over the unit.
(Figure 15) Gently slide top forward until the top drops
into place. (Figure 16) Slide top backward until flush
with the back of the unit. (Figure 17)
Operate the unit in “FAN ONLY” position for a minimum of one hour to insure the cell is thoroughly dry.
NOTE: An occasional “arcing” sound is normal when
operating the unit immediately after cleaning
the Cell and should stop after a few minutes of
operation. If cleaning the Cell does not alleviate
excessive arcing, refer to the Troubleshooting
Section on
page 5.
/
ELECTRONIC
COLLECTING
CONTACTS
Figure 15
\\\\
Figure 16
Figure 14
Figure 17
TROUBLESHOOTING CHECKLIST
Many times service problems that appear to be major can be solved easily. The chart below lists potential problems
and how to correct them. Remember, check the simple things first.
WHAT TO. CHECK WHAT TO DOCONDITION
Unit arcs, sparks or pops
Machine will not operate
Interference with radio
and TV
Unit is not
removing pollutants
No longer notice
“fresh smell”
Machine still does not
operate properly
Electronic Collecting Cell
1. Is Cell cleaned thoroughly? Heavy
deposits of tar
require a stronger cleaner such as
409 or Fantastik.
2. Is Cell completely dry?
3. Is Cell positioned properly?
4. Check for broken wires or
bent plates
5. Are electrical contacts clean
and free of
buildup?
6. Are wall contacts slightly
bent upwards?
Negative Ion
Generator Needle
Power Cord
Electrical Outlet
Cabinet Top
Speed Selection Switch
Blower Wheel
Electrical Outlet
Electronic Collecting Cell
Negative ton Generator Needle
Speed Selection Switch
Unit
Electronic Collecting Cell
Negative Ion
Generator Needle
Charcoal After-Filter
Recheck the above points.
&
nicotine may
mineral
deposit
1. Clean Cell; consult cleaning instructions. Clean
2. Dry Cell; Operate unit on “FAN ONLY” speed until
3. Be sure Cell is positioned properly, not in back-
4. One complete wire may be removed without affect-
5. Remove electrical contacts from Cell, clean
6. Be sure wall contacts are slightly bent upward and
Reposition needle towards back wall of unit by
pressing front center of needle backwards.
Plug power cord into electrical outlet.
Check for power to the electrical outlet. Plug a table
lamp into the electrical outlet to ensure power
availability.
Cabinet Top must be replaced properly to activate
safety switch. Unit will not operate with top removed.
Turn Slide Switch to desired speed.
If blower wheel will not rotate, return unit to Appliance
Service Station, Hattiesburg, MS, for service. See
Warranty Information on back cover for address.
Move unit to a different location away from TV or
radio. Do not operate unit on the same electrical outlet
as TV or radio.
1. Clean Cell if dirty.
2. Be sure Cell is positioned against wall contacts and
Reposition needle towards back wall of unit by
pressing front center of needle back.
Operate unit in any position except “OFF” and
“FAN ONLY”.
1. Operate unit continuously, not occasionally.
2. Check location of unit. Be sure that intake and
1. Clean Cell; Operate unit for 1 week and clean Cell
2. Check for broken wires. If more than 1 wire is
Clean Negative Ion Generator Needle per
cleanina instructions.
Replace Charcoal Filter.
Return unit to Appliance Service Station, Purvis,
MS, for service. See Warranty Information on
back cover for address.
wires with a Q-tip and alcohol.
Cell is completely dry.
wards, and is completely in place (making
good contact).
ing operation. Straighten bent plates if possible.
thoroughly and replace. Clean wall contacts.
Cell is positioned against contacts. (Ref. Fig. 14)
not in backwards.
exhaust areas of unit are not blocked.
again. Notice the “dirt” washed away from Cell.
broken, cell will need to be replaced.
NOTES:
1. Discoloration of aluminum collector cell plates is normal with use, even after cleaning.
2. Blowing smoke directly into the front grill is not a good test for unit performance.
5
TRONIC COLLECTING
2
PRE-FILTER
0
TOP
FILTER
REPLACEMENT PARTS
,
Key Number
1
2
3
4
To order Replacement Parts,
MS, 39475.
write to
Part Number
Description
344950-001 Cabinet Top
342480-001 Pre-Filter
442415-001
6571
Appliance Service Center, P.O. Box 70,6892 Purvis,
Electronic Collecting’cell
Charcoal Filter (Set of 2)
6
1
e”
s
MODEL 2571
OWNER’S
MANUAL
900 AIR CLEANER
AND IONIZER
LIMITED ONE YEAR WARRANTY STATEMENT
This product is warranted for one year from the date of purchase
against electrical and mechanical defects in material and workmanship. If the unit fails to operate during this period, return it, prepaid, to
Appliance Service Station, 117 Central Industrial Row,Purvis,Mississippi, 39475, for repair or replacement without charge at the manu-
facturer’s option. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
Warrantor: Sunbeam-Oster
Made in America
@Sunbeam-Oster Household Products, Distributed by Sunbeam-Oster Household Products, Schaumburg. IL 60173
Committed To Our Environment . . . Printed on Recycled Paper
Household Products
Pan NO. 61801
(:)
(144958-001)
Printed in USA
Loading...