Summer Infant 36134R, 36134T Users Manual

36134

MONITOR OWNER’S GUIDE

LOOKOUT

with No-Hole PrestoMount™

TALK

BACK

Thank you for purchasing the LookOut™ with No-Hole
PrestoMount™ Digital Color Video Monitor by Summer
Infant. Keep this instruction manual for future reference.
Please read the following instructions and warnings
carefully.

SETTING UP THE CAMERA & HANDHELD SCREEN

1

Charge the Handheld

Charge for 7 hours before first
use. After the initial charge,
recharge when necessary for
7 hours. We recommend
charging overnight.
NOTE: While powered off, you
will not see an indicator that
the handheld is charging.

7hr.

Install the Nursery Camera
on tabletop

LookOut™ comes with a camera stand for use on tabletop or dresser.
This can also be handy for travel.
NOTE: For best picture focus, place camera 6 to 8 ft. from crib.

For tabletop use:

1. Attach camera to the stand. Make
sure it securely clicks into the stand.
Plug in camera and follow
instructions in the Secure the Camera
Cord section.

2. Place camera on a flat surface,
such as a dresser or shelf.

Install the Nursery Camera
on wall

NOTE: For best picture focus, place
camera 6 to 8 ft. from crib.

For wall mount use:

1. Before mounting your wall-mount to
the wall, check to make sure that you
like the view on your handheld screen.

2. Peel the paper backing from the
back of the wall mount, discard paper,
and then push mount for 30 seconds
against wall. For best performance, let
the adhesive cure for 60 minutes
before putting the camera onto the
wall mount.

3. Slide camera onto mount until it
clcks into place.

4. Plug cord into left side of camera.
proceed to next page to the Secure the
Cord section.

To remove wall mount:

wall mount

Read all warnings prior to using this product.

WARNING

STRANGULATION HAZARD:
Children have strangled in
cords. Keep this cord out of
the reach of children (more
than 3 ft. (0.9m) away).

Secure the Camera Cord

NEVER place the camera or cords within 3-feet of the crib. Secure the cord
to your wall using the 6 security clips included to keep the cord away from
baby’s reach.

Place one clip close to the camera and at same height as camera,
approximately 3-4 inches away, going away from the camera and from the
crib. This clip will serve as an added measure to help prevent the camera
from falling. Remove and discard the paper backing from the back of the
security clip and press for 30 seconds against wall.

Table top use:

3 ft.

Wall mount use:

3 ft.

Power on the Nursery Camera
& Parent Handheld

1. Press the POWER button on the
camera and hold for 3 seconds. A
green light will appear near the lens.

2. Press and hold the POWER/VIDEO
button on the handheld unit for 3
seconds.
The handheld will automatically
sync with the camera.

NOTE: The handheld unit and the camera
are paired at the factory for privacy
reasons.
(If the handheld and camera are not
paired with each other for any reason,
see "Adding a Camera" section.)

Setting Nursery Temperature
Units (°F or °C)

1. Press the MENU/SELECT button .

2. Select TEMP UNIT from the menu
and press the MENU/SELECT button .

3. Press the UP and DOWN buttons
to select °F or °C. Temperature units
will change to selected unit in the
upper bar.

4. Navigate to EXIT in the menu, then
press the MENU/SELECT button .

Menu screen will return to camera
mode after 8 seconds of inactivity.

For most efficient use, MAKE sure to
move the temperature sensor away from
the nursery camera.

3 sec.

BRIGHTNESS
VIEW CAM
SCAN
ADD CAM
DELETE CAM

TEMP UNITS

EXIT MENU

EXIT MENU

SELECT

SELECT

2

GETTING TO KNOW YOUR HANDHELD

Screen Icons

Nursery Temperature
Display

Talk-back

Zoom

Reception

Current Viewing Camera (1-4)

Battery Life/Plugged In

Function Buttons

Power/Video

Menu/Select

Volume Up

Volume Down

Talk-back

Zoom

Flip out the
kick-stand and place
the monitor on a
stable, level surface.

3

VIEWING YOUR BABY

Adjusting the Handheld
Screen Brightness

1. Press the MENU/SELECT button .

2. Select BRIGHTNESS from the
menu and press the MENU/SELECT
button .

3. Press the UP and DOWN arrow
buttons to increase or
decrease brightness.

BRIGHTNESS

VIEW CAM
SCAN
ADD CAM
DELETE CAM
TEMP UNITS
EXIT MENU

SELECT

Video On/Off Power Save Mode
This feature helps conserve battery life
when not plugged into an A/C adapter.
The audio feature will remain activated,
allowing you to monitor sounds.

1. To activate POWER SAVE, turn off the
handheld’s video by pressing the
POWER/VIDEO button .
The screen will go dark.

2. Press the POWER/VIDEO button
again to wake up the screen.
When the handheld is not plugged in, the
screen will automatically enter power
save mode after 30 seconds.

Zoom In and Out

1. Press the ZOOM button to
zoom in.

2. Press the button again to zoom
out.

4

HEARING & SOOTHING YOUR BABY

Sound-Activated Lights

The LED light bar on top of handheld
will light up as it picks up noises,
even in power save mode.
When battery is low, the first LED
flashes red and the handheld beeps.

Talk-back to Baby

Reassure and soothe baby with the
sound of your voice and press of a
button.

1. Press and hold the TALK-BACK
button to talk to your baby.

2. Release the button to end
talk-back mode.

Volume

Press the UP/DOWN arrow buttons
to increase and decrease the
volume.

tabletop

1. Remove camera from the mount
and pull tab at bottom of mount and
remove from the wall.
Caution: keep one hand on mount
while pulling tab with other hand.

If you ever need to remove the security clips, the clips remove by pulling on
the exposed tab. Caution: keep one hand on security clip while pulling tab
with other hand.You can order more security clips or wall mounts through
our Customer Relations.

Congratulations! You are now ready to use your LookOut™
with No-Hole PrestoMount™ Digital Color Video Monitor!

Summer Infant (USA), Inc. | 1275 Park East Drive | Woonsocket, RI 02895 | 401-671-6551

3/19

36134

MONITOR OWNER’S GUIDE

5

ADDING AND VIEWING CAMERAS

Adding a Camera

Your digital video monitor accepts
up to 4 cameras total. You can
select the one you want to view OR
use the auto-scan mode to cycle
through each camera on an
8-second rotation.

1. Make sure the power is on for
the camera you want to add.

2. Press the MENU/SELECT button
to enter menu screen.

3. Using the DOWN button , scroll
to ADD CAM and press the
MENU/SELECT button to select.

4. Using the UP or DOWN buttons ,
scroll to the camera number you
would like to add and press
MENU/SELECT button to select.

5. Press the SYNC button on the
back of the camera. Three bars
will appear next to the camera
icon to indicate syncing.

If unsuccessful, repeat the above steps.
Extra Cameras:

To order an additional camera (item #36164), please contact our

Consumer Relations Team at 401-671-6551 or visit
www.summerinfant.com/contact.

BRIGHTNESS
VIEW CAM
SCAN

ADD CAM

DELETE CAM
TEMP UNITS
EXIT MENU

EXIT MENU

SELECT

SELECT

Deleting a Camera

1. Press the MENU/SELECT button .

2. Press the DOWN button , highlight
DELETE CAM and press the
MENU/SELECT button to select.

3. Use the UP or DOWN buttons
to highlight the camera you want
to delete.

4. Press the MENU/SELECT button
to delete that camera.

Selecting a Camera to View

1. Press the MENU/SELECT button .

2. Press the DOWN button , highlight
VIEW CAM and press the
MENU/SELECT button to select.

3. Press the UP and DOWN buttons
to select an available camera.
Blue color indicates paired
cameras.

4. Press MENU/SELECT button to
confirm selection.

Scanning Cameras

1. Press the MENU/SELECT button .

2. Using the DOWN button , select
SCAN and press the MENU/SELECT
button .
Scanning cameras will begin,
cycling through each active
camera every 8 seconds.

3. To stop scanning, press the
MENU/SELECT button .

BRIGHTNESS
VIEW CAM
SCAN
ADD CAM

DELETE CAM

TEMP UNITS
EXIT MENU

EXIT MENU

BRIGHTNESS

VIEW CAM

SCAN
ADD CAM
DELETE CAM
TEMP UNITS
EXIT MENU

EXIT MENU

BRIGHTNESS
VIEW CAM

SCAN

ADD CAM
DELETE CAM
TEMP UNITS
EXIT MENU

SELECT

SELECT

SELECT

SELECT

SELECT

WARNING

Adult assembly required. Keep small
parts away from children when
assembling.

WARNING

THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT
SUPERVISION.

• STRANGULATION HAZARD - Children have STRANGLED in

cords. Keep this cord out of reach of children (more than
3 feet (0.9 m) away from the crib). Use enclosed Security
Clips to help secure cord away from baby’s reach. Never
use extension cords with AC Adapters. Only use the AC
Adapters provided.

• When an AC Adapter is plugged into an electrical

outlet, do not touch the exposed end.

• Test monitor before first use, periodically, and when

changing location of the Camera.

• Do not use monitor near water (such as bathtub, sink,

etc.).

• Keep monitor away from heat sources (such as stoves,

radiators, etc.).

• Make sure there is proper ventilation around all monitor

components. Do not place on sofas, cushions, beds, etc.
which may block ventilation.

• This product is not a toy.Do not allow children to play

with it.

• This product contains small parts. Adult assembly

required. Exercise care when unpacking and assembling
the product.

WARNING

BATTERY:

• Use only the original rechargeable battery provided.

Please contact Summer Infant (USA), Inc. for
replacement battery. Contact information can be found
on the back page of these instructions or on the battery
itself.

• Do not short-circuit supply terminals.

• Only the recommended battery or equivalent are to be

used, volts and size.

• Remove battery when product is stored for long periods

of time or when battery is exhausted.

• Dispose of exhausted battery properly.

• Keep all batteries away from children.

FCC INFORMATION

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by Summer
Infant may void the users authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiver

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

CAUTION: 1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. 2. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.

This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1)This device may not cause interference.(2)This device must accept any
interference, including interference that may cause undesired operation of
the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil
est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :(1)L’appareil ne
doit pas produire de brouillage; (2)L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.

This equipment complies with IC RSS‐ 102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body

Cet équipement est conforme aux limites d'exposition aux radiations IC
CNR‐ 102 établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec une distance minimale de 20 cm entre le
radiateur et votre corps.

Summer Infant (USA), Inc. Monitor Warranty Policy

Summer Infant (USA), Inc. will repair or replace (at our option) your unit free
of charge for 12 months from the date of purchase if the unit is defective in
workmanship or materials. To claim your repair/replacement, the product
must be returned to Summer Infant along with a copy of the original
purchase receipt. In the absence of the purchase receipt, the warranty will
be 12 months from the date of manufacture. This warranty does not apply to
normal wear or damage from misuse, abuse, improper storage and
handling, installation, accident, unauthorized repair or alteration. Please
contact our Consumer Relations Team by phone at 401-671-6551 or via
e-mail at summerinfant.com/contact for details. For sale and use in the USA.
The warranty is null and void if used outside its intended territory.

IMPORTANT SAFETY INSTRUCTIONS

1) Read Instructions - All the safety and operating instructions should be
read before the product is operated.

2) Retain Instructions - The safety and operating instructions should be
retained for future reference.

3) Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.

4) Follow Instructions - All operating and use instructions should be
followed.

5) Cleaning - Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6) Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

7) Water and Moisture - Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.

8) Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory
recommended by the manufacturer.

9) Ventilation - Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surfaces. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilationis provided
or the manufacturer's instructions have been adhered to.

10) Power Sources - This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local
power company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.

11) Power-Cord Protection - Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.

12) Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.

13) Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.

14) Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.

15) Servicing - Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.

16) Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjusting only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicated a need for service.

17) Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.

18) Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.

19) Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.

20) Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.

TIPS & TROUBLESHOOTING

No picture or sound

• Make sure the camera and handheld monitor unit are paired.

• Make sure the camera and handheld monitor unit are turned on.

• Make sure the AC adapters are plugged in.

• Make sure the outlets are working.

Sound but no picture

• Press the Video On-Off Button once to turn on video mode.

• Make sure nothing is blocking the camera.

• Test reception by moving the handheld unit and/or camera to

different locations.

• Make sure the camera and handheld monitor unit are paired.

Picture but no sound

• Power the handheld completely off, then turn handheld back on.

• Turn up the volume using Volume Control.

Picture not clear

• Wipe camera lens with microfiber or clean, damp cloth.

• Position the handheld unit closer to the camera.

• Move the handheld unit away from other electronic devices, cordless

phones, etc.

• Adjust the brightness using the Brightness Control.

• Test reception by moving the handheld unit and/or camera to different

locations.

• Place camera 6 to 8 ft. from crib for optimized focus. Make sure to follow

instructions and warnings for camera placement.

TIPS & TROUBLESHOOTING (cont.)

Squealing sound coming from speaker on Handheld Unit

• Move the handheld unit and camera further away from each other.

• Turn the volume down using Volume Control.

• Power both the handheld and camera off completely. Remove and

re-insert the handheld battery, then turn both back on.

Handheld is beeping

• If no video, turn on camera.

• If battery is low, charge battery.

After the initial charge, recharge when necessary for 7 hours. We
recommend charging overnight.

Temperature listed as LL or HH

• Room temperature is outside of the thermometer limits. The thermometer

is effective in between 32°F – 100°F (0°C – 38°C).
If you receive a false error message, please contact our Consumer
Relations Team.

Camera isn’t syncing with handheld

• Delete camera and add it back.

We're here to help!

If you have issues or questions not addressed in this Owner’s Guide,
contact us at 401-671-6551 or www.summerinfant.com/contact
Do not return the product to the store.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT EXPOSE TO RAIN OR MOISTURE

ORDERING REPLACEMENT PARTS

To order replacement parts or extra cameras, contact our Consumer
Relations Team at 401-671-6551or visit www.summerinfant.com/contact

• Camera AC Adapter:...........................................................#29580-05

• Handheld AC Adapter:........................................................#29580-13

• Extra Camera:.......................................................................#36164

• Handheld Screen:................................................................#36134-02

• Wall Mount:...........................................................................#36134-21

• Cord Clips:............................................................................#36134-22

• LookOut™ Tabletop Stand:.................................................#36134-20

• Rechargeable Ni-MH AAA size 4.8V 800mAh battery:...#29580-10

CONTACT US

Summer Infant (USA), Inc.

1275 Park East Drive
Woonsocket, RI 02895
401-671-6551

Summer Canada, Ltd.

200 First Gulf Blvd., Unit C
Brampton, Ontario,
Canada L6W 4T5
905 456-8484

© 2018 Summer Infant (USA), Inc.

Colors and styles may vary.

Please retain information

for future reference.

Made in China.

732-2994000-0700

732-3613400-0700