Summer Infant 200T, 200R Users Manual

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.

NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

FCC statement

User manual

Tips For Improving Reception:

• Position the Monitor closer to the CAMERA if necessary.

• Move Monitor away from other monitors, cordless phones,

walkie-talkies, etc.; moving even slightly could greatly improve reception.

• If you hear a feedback or squealing noise, move the CAMERA and the

Monitor further away from each other.

Battery Installation

Monitor: This step is only needed if replacing battery.

1. Locate the battery compartment door on back of monitor.

2. Slide open battery door and insert battery. Ensure correct connection.
Slide battery door back in place.

Portable Camera Battery Pack:

Set Up & Use

1. Locate the battery compartment door on bottom of camera battery
pack.

2. Use Phllips Head Screwdriver to remove battery door.

3. Insert 4’AA’ batteries (not included). Ensure correct connection.

4. Place battery door back and screw closed.

5. Place camera ontop of battery pack. Twist camera clockwise untill the
arrow from the camera are aligned with the “lock” arrow on battery
pack.

6. Turn camera to “ON” position. Note: Camera battery pack will supply
portable power for upto 10 hours. Rechargeable batteries are
recommended.

7. To remove camera from battery pack, twist camera counterclockwise
untill the arrow from the camera are aligned with the “UNLOCK” arrow
on the battery pack.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications not expressly approved by Summer Infant may void the users authority to operate this

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

CAUTION: 1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained

between the antenna of this device and all persons. 2. This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Summer Infant, Inc. Monitor Warranty Policy

Summer Infant, Inc. will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the unit is

defective in workmanship or materials. To claim your repair/replacement, the product must be returned to Summer Infant along with a

copy of the original purchase receipt. In the absence of the purchase receipt, the warranty will be 12 months from the date of

manufacture. This warranty does not apply to normal wear or damage from misuse, abuse, improper storage and handling,

installation, accident, unauthorized repair or alteration. Please contact our Customer Service Department by phone at 1-800-268-6237

or via e-mail at [e-mail] for details.

BATTER Y W ARNING:

• Use only the original rechargeable batteries
provided. Please contact Summer Infant, Inc. for
replacement batteries. Contact information can be
found on page 12 of these instructions or on the
battery itself.

• Do not mix old and new batteries.

• Do not mix alkaline, standard,
or rechargeable batteries.

• Batteries are to be inserted with correct polarity.

• Clean battery and product contacts prior to
battery installation.

• Do not short-circuit supply terminals.

• Only the recommended batteries or equivalent are
to be used, volts and size.

• Remove batteries when product is stored for long
periods of time or when batteries are exhausted.

WARNING:

THIS PRODUCT CANNOT REPLACE RESPONSIBLE
ADULT SUPERVISION.

• Prevent cord entanglement – do not place Camera in crib
or within arm’s reach of the baby. Use enclosed Security Clips to help
secure cords away from baby’s reach.
Never use extension cords with AC adapters. Only use
the AC Adapters provided.

• When an AC Adapter is plugged into an electrical outlet,
do not touch the exposed end.

• Test monitor before first use, periodically, and when changing location
of the Camera.

• Do not use monitor near water (such as bathtub, sink, etc.).

• Keep monitor away from heat sources (such as stoves, radiators, etc.).

• Make sure there is proper ventilation around all monitor components.

Do not place on sofas, cushions, beds, etc. which may block
ventilation.

• Nursery monitors use public airwaves to transmit signals. This monitor
may pick up signals from other monitors or similar devices and signals

Special Features:

•

Belt Clip: For convenience and portability, you can clip the Monitor to
your belt or waistband after a battery has been installed.

•

Footrest: The Monitor has a built-in footrest for tabletop convenience.
Simply flip out footrest and place the Monitor on a stable, level surface

• Video Sleep Mode: While operating on battery power, the video
screen will go to sleep, to conserve battery power. Audio and

sound lights will function normally. Press the Video On/Off to resume

viewing. This option is NOT available when using AC adapter.

• Sound Lights: The 4 Sound Lights will illuminate on the Monitor
depending on the level of your baby’s sounds. For example, if your
child is just cooing, only one or two lights will illuminate. If your baby
is crying, several will illuminate, depending on how loud she is
crying. This feature is particularly helpful if you are in a noisy room.

• Quick View/Video On/Off Button: This button turns the video
mode on. If you only want to hear your baby, press the Quick

View/Video On/Off Button again to shut off the video. The Quick
View/Video On/Off Button is ideal for easily turning on the video

option in the middle of the night.

• Night Vision: In a darkened room, the Monitor will automatically
use its infrared LED’s to transmit a clear image of baby, so you can
see your child at night!

• Multi-Position Camera/Microphone: The Camera/Microphone
should be positioned so it is facing baby as much as possible. This
multi-position feature is unique to Summer Infant nursery monitors. It
allows the microphone to focus on baby’s voice while filtering out
other household noises.

• A/V Cable: To view video through your TV, plug the AV cable jack
connection into monitor and connect the other ends into the

corresponding color coded parts on your TV. Scroll through A/V

inputs on your television’s menu until monitor picture is visible.

Note: The Monitor’s power button must be turned ON and CAM

pre-selected before connecting the AV cable. Once the AV cable is

connected the Monitor’s controls cannot be activated.

use on a 27” TV or smaller.

For best results

Set Up & Use

CAMERA

Table Top or Wall Mounting:

Determine a location for the
the best view of your baby in his crib. Place the
a flat surface, such as a dresser, bureau, or shelf. Or mount
the

Camera
arm’s reach of baby. Do not place the Camera near open
windows, direct sunlight or heat sources. Be sure to test

reception and Camera positioning before mounting to a wall
(see "Testing Your Initial Set Up" section).

To Wall Mount:

1) Pre-drill a hole in the wall
(3/16", 4.8mm, drill bit) (Figure A).

2) Insert the wall anchor (included)
into the hole and with a hammer,
tap gently on the end until the wall
anchor is flush with the wall.

3) Insert the screw (included) into the
wall anchor and tighten screw until
only 1/4" (6.2mm) of the screw
is exposed.

4) Insert AC Adapter into the Camera’s
AC Adapter Jack.

5) Slide the back of the
onto the screw until the

6) Plug the AC Adapter into a standard electrical outlet.

7) Secure the cord to the wall using the 6 Security Clips
included to keep cord away from baby's reach (Figure B).

8) Slide switch on side of
POWER ON LED will illuminate solid green.

MONITOR

To Use in Video and Audio Mode:

on a wall. Be sure not to place camera in crib or within

Camera

Camera

Camera

Camera

that will provide

Camera

down

is secure to the wall.

to ON and the

on

Features & Components:

Camera (Front View):

Security Clips (6):

Camera Base:

Wall Anchor (1)
and Screw (1):

Monitor:

Monitor Charging Stand:

AC Adapter: (2)

AV Jack:

FPO

Power

Power

ON

Press for three seconds
to power on. Power on
screen will appear
while software is boot­ing up.

OFF

Press for three seconds
to power off. Power off
screen will appear while
software is booting
down.

Note: Everytime you
power your monitor on
it will default to camera
one.

Pan/Scan

Pan/Scan with arrows

Pan/Scan- Use up, down,
left and right arrows to
control camera movement.

A

Add Camera

B

Note: This product can accept up to

four cameras. To order an additional
camera (#28064) please contact our
customer service department by
phone at 1-800-268-6237 or via e-mail at
[e-mail]
for details. For Europe call +44
(0)206-420-4429 or via e-mail at
[e-mail]

Talk Back

Brightness

Brightness Control

View Camera

1

Video On/Off

cam 1

Camera
Options

To control brightness press bright­ness control button from the
touch menu screen. Use up and
down arrows to control brightness.

To view a camera in use press
camera button from the touch
menu.

Use up and down arrows to
navigate to the view cam
option.

Press (select) to enter the
view cam menu.

Zoom

+ and -

Remote Camera Pan

Volume Control

Left and Right

Home Button­allows user to
escape from menu
at anytime.

Home

Tap anywhere on the
touchscreen L and
the menu bars will
appear. Menu
disapears after
10-12 seconds of
inactivity.

A blue rectangle will
appear around the
button you are press­ing- to indicate to the
user which button is
pressed.

Zoom

To zoom into picture press the
zoom button from the touch
menu screen.

The screen will zoom in one level­toward the center of the screen.
Press zoom out and the
screen will zoom out to full view.

Delete Camera

Use arrows to navigate to
the delete cam option.

Press (select) to enter the
delete cam menu.

• Dispose of exhausted batteries properly.

• Do not recharge non-rechargeable batteries.

• Rechargeable batteries are only to be charged
under adult supervision.

• Keep all batteries away from children.

broadcast by this monitor may
be picked up by other receivers.

• This product is not a toy. Do not allow children to play with it.

• This product contains small parts. Adult assembly required.
Exercise care when unpacking and assembling the product.

screwdriver (not included)

For technical support

see back page.

For use with children

from birth and up.

digital color video monitor

02000

Tools required:

Step 1: Place the Monitor in the room from which you want to monitor
your baby (ie. bedroom or living room). Plug an AC Adapter into the AC
Adapter Jack and the other end into a standard electrical outlet.
top of the unit.

Step 2: Press and hold “POWER ” button for 4 seconds to turn on
until video or Summer logo appears on screen.

Step 3: For audio and no video, press the VIDEO ON/OFF button on

top of the unit.

Step 4: To turn the monitor off completely, press and hold the
“POWER ” button for 3 seconds.

Testing Your Initial Setup:

Be sure to test your Monitor’s reception before initial use.
We also recommend testing your Monitor’s reception periodically. Please

keep in mind that the Slim & Secure™ Handheld Color Video Monitor will

not provide the same level of picture quality as your television with
cable, satellite dish, or digital service.

To test reception you will need two adults. One adult should view the
picture on the Monitor while the other is in the nursery to adjust the
Camera. Often the quality of the reception can be improved by slightly
repositioning the Camera, Monitor, or both. It may help to place a stuffed
animal or doll in the crib to simulate the position and size of your baby.
Adjust the picture quality on the Monitor as needed by using the
Brightness Adjustment on the front of the Monitor.

To test sound quality, have one adult speak in both a normal tone and a

whisper near the crib. Adjust volume on the Monitor’s Volume

Adjustment as needed.

To Use the Video Monitor in Portable Mode:

For use in portable mode, the Monitor requires 1 3.7V LITHIUM-ION

rechargeable battery (included).

To add camera press
Camera Button from the
touch menu. Use up and
down arrows to navigate to
the add cam option.

Press (select) to enter the
add cam menu.

2

Press and hoild the Code button on
back of camera head until green
LED starts blinking.

3

1 2 3 4

Once view cam is highlighted the
4 cameras will appear. Note: If

view cam was selected by acci­dent press left arrow key to exit the
numbered cam menu.

Use the up and down arrows to
highlight the camera you would
like to view and press select to

view that option.

Camera Scan

To scan all cameras in use for 8
second intervals, press camera
button from the touch menu. Use the
up and down arrows to navigate to
the scan option. Press select to
enter the scan mode.

Use the left and right arrows t
highlight the camera you would like
to delete and press select to
delete that camera. To exit hit the
home key

cam 1

The monitor will automatically scan
through all camera options every 8
seconds. To stop scan mode at anytime
press the home button. If scan mode
stops on an undesired camera selection,
press camera button from touch menu
and select view camera option. Follow
directions above listed in view camera.

INSTRUCTION MANUAL

We at Summer Infant stand behind all of our products. If you are not completely satisfied or

© 2010 Summer Infant, Inc.
Colors and styles may vary.
Please retain information for future
reference.
8/10

have any questions, please contact our customer service department at

(For Europe call [phone] or [e-mail])

MADE IN CHINA.

1-800-268-6237 or [e-mail]

Summer Infant, Inc.

1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237

Summer Infant Europe, LTD.

Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire WD23 3HP UK
[phone]

Please read the following instructions and warnings carefully.
Keep this instruction manual for future reference.

Adult assembly required. Keep small parts

away from children when assembling

WARNING:

Tips:

• Before using Monitor in portable mode (battery), be sure to

charge battery 12-16 hours.

• To charge battery, plug the larger AC Adapter into the

Monitor’s AC Adapter Jack. Plug the other end into a standard
electrical outlet.

• After initial 12-16 hour charge, to achieve optimal battery life,

charge battery overnight and unplug all day during use.

• Note: Only charge battery when low indicator light comes on.
Constant recharging of your battery before low battery indicator
light comes on will decrease the life of your batteries.

• When battery is low, the Power On LED will illuminate amber,

indicating that the battery needs to be recharged.

• To conserve battery power, use AC Adapter whenever possible.

Remove battery during long periods of non-use.

CAUTION:

.

KEEP SMALL PARTS OUT

OF CHILD’s REACH

.

• If battery is exhausted, remove immediately from the Monitor.

• Properly dispose of exhausted battery.

While syncing the camera will blink,
once fully synced the camera will
turn solid black.

4

The cameras that are not synced
will be gray and the synced cam­eras will be black. The camera will
automatically sync to the next
available channel.

Problem Solving:

No picture or sound on Monitor

• Make sure the Monitor is turned on

• Make sure the AC Adapters are plugged in

• Make sure the outlets are working

• Make sure Monitor and Camera are

SYNCHED up.

Sound but no picture on Monitor

• Press the Quick View/Video On/Off Button

once to turn on video mode

• Try adjusting the Brightness Control on the

Monitor

• Test reception by moving the Monitor and/or

CAMERA to different locations

If you experience a problem that is not noted in this manual, please do not return the product to the
store. Our Customer Service Department may have a simple solution to your problem. Please contact us
at 1-800-268-6237 or email us at [e-mail].

Picture but no sound

• Turn up the volume on the Monitor using
the Volume Control

Picture not clear

• Position the Monitor closer to the CAMERA

if necessary

•

Move Monitor away from other monitors,

cordless phones, walkie-talkies, etc.

• Try adjusting the Brightness Control on the

Monitor

• Test reception by moving the Monitor

and/or CAMERA to different locations

Squealing sound

• Move the CAMERA and the Monitor

further away from each other