Sub Zero 7004812, 7020163, 7004810, 7020161, 7012623 Installation
...
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624
(Instructions for Dual Grille Kits Listed Above)
7010064 / Rev C / March, 2011
NOTES:
• The production grille assemblies MUST
be removed before beginning.
• The dual installation heater assembly and the center trim piece MUST be attached to the right side of the
unit that will be installed at the left side of the rough-in opening.
• The main frame shim MUST
be attached to the left side of the unit that will be installed at the right side of
the rough-in opening.
BI SERIES UNITS ARE HEAVY AND CAN BE UNSTABLE WHEN ATTEMPTING TO INSTALL THEM. WHEN
MOVING A BI SERIES UNIT KEEP THE DOORS AND DRAWERS TAPED CLOSED. THE ANTI-TIP COMPONENTS SUPPLIED WITH BI SERIES UNITS MUST BE UTILIZED AS SPECIFIED IN THE INSTALLATION
MANUAL. THE FRONT LEVELING LEGS OF A BI SERIES UNIT MUST BE EXTENDED TO THE FLOOR TO
COMPLETE THE INSTALLATION. IF A BI SERIES UNIT WERE TO TIP AND FALL IT COULD CAUSE SERIOUS INJURY OR DEATH!
Page 1 of 7
CONTAINS:
QTY
DESCRIPTION
2 Spacer, 1/8" X .204 Id
2 Bolt, #10-24 X 1/2" Roundhead
4 Bolt, Tensilock 5/16-18 X 3/4
1 Clip, Cord Plastic 5/16 X 1/2
6 Screw, #8-32 X 1/2 Pan Hd
1 Screw, #10-12 X 1-1/4 Truss Hd
9 Screw, 10-12 X 3/4, 6-Lobe Ph
1 Nut, Dual #10-24 X 1 (7001272)
4 Threaded Insert,5/16-18 Hx Opn
1 Trim, Dual Install Center Short
1 Grille, Dual Framed 60-1/4 (7004808 Kit Only)
1 Grille, Dual Framed 72-1/4 (7004809 Kit Only)
1 Grille, Dual Overlay 60-1/4 (7004810 Kit Only)
1 Grille, Dual Overlay 66-1/4 (7012623 Kit Only)
1 Grille, Dual Overlay 72-1/4 (7004811 Kit Only)
1 Grille, Dual SS 60-1/4 (7004812 Kit Only)
1 Grille, Dual SS 66-1/4 (7012624 Kit Only)
1 Grille, Dual SS 72-1/4 (7004813 Kit Only)
QTY DESCRIPTION
1 Bracket, Dual Install Bottom
1 Bracket, Dual Grill Support
1 Bracket, Dual Grill Slide
4 Screw, 5/16 X 3/4 Thread-Forming
1 Instructions,Dual Grill Kits
1 Kickplt, Blk 59.25 (7004808 & 7004810 Kits Only)
1 Kickplt, Black 65.5 (7012623 Kit Only)
1 Kickplt, Blk 71.75 (7004809 & 7004811 Kits Only)
1 Kickplate, Stainless 59.7 (7004812 Kit Only)
1 Kickplate, Stainless 65.5 (7012624 Kit Only)
1 Kickplate, Stainless 71.7 (7004813 Kit Only)
1 Bracket, Dual Install Top
3 Bracket Assy,Dual Trim
1 Threaded Insert,Install Tool
1 Heater Assy, Dual Installation
1 Shim, Assy Main Frame
1 Bracket Assy, Magnet Center
2 Bracket Assy, Magnet Side
6 Nut, 10-24 Hex Flange Lock
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624
(Instructions for Dual Grille Kits Listed Above)
7010064 / Rev C / March, 2011
A. Heater Installation Instructions
NOTE: Heater assembly MUST be attached to right side of left hand unit.
1. Clear foil from mounting holes of Heater Assembly.
2. Place heater against right side of unit with wires up and foil side in, positioning the heater 2” (51mm)
from top edge of cabinet and 1” (25mm) from back edge of cabinet (See Figure 1).
3. Using the heater as a template, mark the heater mounting holes onto the cabinet with a pencil, then
remove heater.
4. Drill a 7/64'' (3 mm) hole at each location marked in step 3.
NOTE: To avoid drilling through inner liner, use a short drill bit inserted into drill chuck so no more than
1/2” (13 mm) to 3/4” (19 mm) of bit is protruding.
5. Attach heater to unit using the #8-32 X 1/2'' Pan Head Screws at the holes just drilled.
6. Locate the panel mount 4-prong female receptacle at back side of power cord box, extract empty male
safety plug from female receptacle, then insert heater’s 4-prong male plug into female receptacle (See
Figure 1).
7. Attach the 5/16 X 1/2 Plastic Cord Clip in a convenient location by the water filter then route excess
heater wires through the clip as well as any other available wire clips.
Figure 1. Heater Installation
Rear View of
Power Cord Box
and 4-Prong
Heater Plug
Connection
Page 2 of 7
Extract safety plug, then
insert heater’s 4-prong
male plug
1”
2”
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624
(Instructions for Dual Grille Kits Listed Above)
7010064 / Rev C / March, 2011
Figure 2. Center Trim and Trim Brackets
Figure 5. Left Hand Unit Installed
Figure 3.
Main
Frame
Center
Trim
Figure 4.
Main
Frame
Center
Trim
(Top View) (Top View)
Page 3 of 7
B. Center Trim Installation Instructions
NOTE: Assemble center trim piece and
trim brackets first, then attach trim to right
side of left hand unit.
1. Attach the three L-Shaped Dual Trim
Bracket Assemblies to the Dual Install
Center Trim Piece, using nuts provided.
DO NOT tighten nuts at this time (See
Figures 2).
2. With trim brackets loosely attached,
hold center trim piece at about a 75°
angle against right side main frame
(See Figure 3). Then, rotate it toward
the unit so the trim brackets hook in
behind the main frame (See Figure 4),
now align bottom of center trim piece
with bottom of main frame and tighten
nuts.
C. Install Unit into Left Side of Rough-in
Opening
Install unit into left side of rough-in opening
as specified in installation manual (See
Figure 5).
Loading...