Subaru Tribeca Navigation-System 2010 Owner's Manual

This supplement contains a detailed description of the Navigation System and instructions for proper operation. Please read this supplement carefully before using your navigation system. Please keep this supplement with your Owner’s Manual and leave it in the vehicle at the time of resale. The next owner will need the information it contains.

FUJI HEAVY INDUSTRIES LTD., TOKYO, JAPAN

is a registered trademark of FUJI HEAVY INDUSTRIES LTD.

Contents

Safety Warnings.......................................................................3

Before Use ................................................................................4

System Components and Controls........................................8

Starting Up the Navigation System ....................................10

Volume....................................................................................12

Markers and Controls Displayed on Maps..........................13

Screens During Route Setting ......................................................13

Screens During Route Guidance ..................................................15

Menu Screen Keys and Functions........................................16

Map Operations .....................................................................18

Selecting Map Orientation ............................................................18

Changing Map Scale ......................................................................19

Setting Route .........................................................................21

Setting Destination ........................................................................21

Setting destination/waypoints by scrolling the map ........................................21

■ Selecting route ..........................................................................................23

Setting the destination from the navigation menu ..........................................24

■ “Address” method ..................................................................................26

■ “Memory Point” method ..........................................................................29

■ “Home” method or method using stored destinations ............................31

■ “Point of Interest” method ......................................................................32

■ “Previous Destination” method ................................................................34

■ “Select from Map” method ......................................................................35

■ “Freeway Entrance/Exit” method ............................................................36

■ “Emergency” method ..............................................................................38

■ “Coordinates” method ..............................................................................40

■ “Intersection” method ..............................................................................42

■ “Phone number” method..........................................................................44

■ Using “Change Search Area” function ..................................................46

Route Guidance .....................................................................47

Route Guidance Screen..................................................................47

Zoom-in Map at Intersection ........................................................48

Dual Map Display............................................................................49

Freeway Information ......................................................................50

Replaying Voice Guidance ............................................................50

Compass Mode ..............................................................................51

Route Options ........................................................................52

Setting Route Options ....................................................................52

Search condition ..............................................................................................54

Detour ..............................................................................................................55

Route preferences............................................................................................56

Destination and waypoints ..............................................................................57

■ Addition of waypoints ..............................................................................57

■ Modifying destination or waypoint positions ............................................59

■ Modifying visiting order ............................................................................61

■ Deleting destination or waypoints ............................................................63

■ Deleting destination and all waypoints......................................................64

Display route ....................................................................................................65

Route preview ..................................................................................................66

■ Setting conditions for simulation drive ......................................................67

Navigation Setup...................................................................69

Setting Your Navigation System ..................................................69

User settings ....................................................................................................71

Quick POI selection..........................................................................................74

Language Selection ..........................................................................................76

Navigation information ....................................................................................77

■ Vehicle signal ............................................................................................77

■ Version ......................................................................................................78

Calibration ........................................................................................................79

■ Adjusting current position and direction....................................................79

■ Distance ....................................................................................................81

Set clock ..........................................................................................................82

Restore system defaults ..................................................................................84

Contents

Stored Locations....................................................................86

Memory points ................................................................................................89

■ Storing new memory points ......................................................................89

■ Reviewing and modifying memory points ................................................91

■ Deleting memory points ............................................................................94

■ Deleting all memory points........................................................................95

■ Modifying category names ........................................................................96

Avoid area ........................................................................................................97

■ Storing avoid areas ....................................................................................97

■ Reviewing and modifying avoid areas ......................................................99

Home..............................................................................................................100

■ Storing home ..........................................................................................100

Previous destination (deleting stored locations) ............................................102

Preset destinations ........................................................................................104

■ Storing preset destinations......................................................................104

■ Reviewing and modifying preset destinations ........................................106

Other Functions ...................................................................108

Displaying POIs on a map ..............................................................................108

■ Local search ............................................................................................109

Displaying POI data ........................................................................................111

Deleting POI markers ....................................................................................112

Editing Quick POI categories ........................................................................113

SUBARU dealership search............................................................................116

■ SUBARU dealership search from POI ....................................................116

■ Displaying SUBARU dealership on map ..................................................118

General Information ............................................................120

■ Accuracy of vehicle position ..................................................................120

■ How the vehicle position is detected ....................................................121

■ Accuracy of the route guidance ..............................................................122

When a Problem Occurs ..............................................................123

Safety Warnings

You will find a number of WARNINGs, CAUTIONs and NOTEs in this supplement.

These safety warnings alert you to potential hazards that could result in injury to you or others.

Please read these safety warnings as well as all other portions of this supplement carefully in order to gain a better understanding of how to use your Navigation system safely.

WARNING

A WARNING indicates a situation in which serious injury or death could result if the warning is ignored.

CAUTION

A CAUTION indicates a situation in which injury or damage to your vehicle including Navigation system, or both, could result if the caution is ignored.

NOTE

A NOTE gives informaton or suggestions how to make better use of your Navigation system.

Before Use

WARNING

READ THIS MANUAL FIRST

Read this supplement carefully before using your navigation system. We are not liable for accidents or other problems resulting from failure to follow the instructions in this supplement.

OBEY LOCAL ROAD SIGNS AND REGULATIONS

Always obey local road signs and regulations while following instructions given by the navigation system. Some of the data on the DVD-ROM disc may be outdated due to changes in local road signs and regulations. Furthermore, the data on the DVD-ROM disc does not take into account variable factors such as the weather, road congestion at different times of the day, temporary road closures due to road construction, and special events. Local road signs and regulations always take precedence over directions given by the system.

Failure to obey them could place you in physical danger or in violation of the law.

DRIVE SAFELY

• Before following an instruction (for example, in the case of changing direction) given by the system, check that the action would be safe to take in the current traffic conditions. Continue to pay attention to safety while following any instruction.

• Do not be distracted by the navigation screen. Failure to keep your attention on the road could lead to an accident. When you need to look at the screen while driving, do so for the shortest time possible and avoid staring at the screen.

• You must stop the vehicle in a safe place before operating the navigation system. For safety’s sake, some of the navigation system’s controls and functions cannot be used unless the vehicle is stationary.

• Use this system only in locations where it is legal to do so. Some states/provinces may have laws prohibiting video screens within sight of the driver.

VOLUME LEVEL

Keep the system’s volume level low enough for you to be able to hear outside sounds while driving. To do otherwise may prevent you from reacting appropriately to traffic conditions and could result in an accident.

Before Use

CAUTION

FOREIGN OBJECTS

Do not allow foreign objects to enter the disc insertion slot, including your fingers.

Foreign objects inside the system’s main unit could cause an electric shock or a fire. If the main unit emits smoke or an unusual smell, stop using the system immediately and you contact the nearest SUBARU dealer.

STOP OPERATION IN THE EVENT OF A PROBLEM

In the event of a problem such as the absence of sound or video, try pressing the reset button. Should the problem persist, stop using the system and you contact the nearest SUBARU dealer.

(The reset button is also used when you need to upgrade the program. Insert an upgrade disc and press the reset button.)

NEVER DISASSEMBLE OR MODIFY THE SYSTEM

Any attempt to disassemble or modify any part of the system could lead to an electric shock or a fire, or some other type of accident.

CAUTION

The displays contain mercury. Therefore, the displays must be removed before vehicle disposal. Once the displays have been removed, please reuse, recycle or dispose of them as hazardous waste.

Before Use

■ Points to note before use

Starting the engine before using the system

The navigation system can be used with the ignition key in either the ON position or the ACC position. To preserve the battery, however, it should be used with the engine running whenever possible. Using the system for a long time with the engine off can cause the battery to run down.

Delay before display of current position

The system will not immediately display a correct indication of your vehicle’s current position after being switched on for the first time or after the battery has been disconnected for a long time. It will display a correct current position indication as soon as it receives Global Positioning System (GPS) signals.

Program reloading after battery disconnection

The navigation program will be erased from the system’s memory if the battery is disconnected. If this happens, load the provided DVD-ROM disc in the system’s main unit and turn the ignition switch to the ON or ACC position. The system will automatically reload the program and start operating normally again.

Incorrect operation on rough roads

The system may operate incorrectly or be unable to read the data on the DVD-ROM disc when subjected to severe vibration caused by driving on rough roads.

Handling the GPS antenna

Do not paint the antenna. Doing so could impair or prevent signal reception.

Disabled switches

Some switches are disabled during operation of the system. These switches are displayed in fainter colors and no messages are displayed for them.

Risk of damage to the main unit

Be mindful of the occupant compartment temperature. Using the system when the occupant compartment temperature is extremely high or low can damage it or cause it to malfunction. Also, note that the system’s main unit can be damaged by strong vibration and by any metallic object or water that gets inside.

Condensation

Condensation can form on the lens inside the main unit when there is a rapid change in occupant compartment temperature (for example, when the heater is switched on in cold weather). Such condensation can cause the system to operate abnormally. If you wait an hour or so for the condensation to disappear, the system should start working normally again. If normal operation is still not restored after several hours, we recommend that you contact the nearest SUBARU dealer.

Replacing the DVD-ROM disc

If you need to replace the DVD-ROM disc, make sure the replacement disc is compatible with your system’s main unit. Inserting an incompatible disc could damage the unit.

■ Handling precautions for DVD-ROM discs

• Handle DVD-ROM discs carefully. Any DVD-ROM disc with excessive warping or scratches on its surface can cause reading errors.

• Store DVD-ROM discs away from direct sunlight, which can cause warping and render them unusable.

• DVD-ROM discs rotate at high speeds inside the system’s main unit. Never use a cracked or badly warped disc; doing so could damage the unit.

• To clean a DVD-ROM disc, lightly wipe it with a soft cloth in straight lines from the center hole toward the outer edge.

• Never clean DVD-ROM discs with benzene, thinner, record spray, antistatic spray, or chemical swabs.

• Do not touch the DVD-ROM disc’s data surface (the surface without a printed label). A dirty data surface can cause reading errors. Always hold a DVD-ROM disc by the center hole and at one point on the outer edge, or by two points on the outer edge.

• Do not write anything on DVD-ROM discs or affix anything, such as stickers, to them.

Before Use

System Components and Controls

z Monitor

This button is used to display the destination entry screen of the navigation system.

This button is used to display the menu screen of the navigation system.

This button is used to switch to the navigation system’s current map screen from any other screen.

This button is used to zoom out or zoom in the map displayed on the screen.

This button is used to display the Audio or RSE (Rear Seat Entertainment) screen.

This button is used to display the vehicle information screen. Refer to the Owner’s Manual Supplement for Monitor System for further details.

This button is used to adjust the brightness and contrast of the screen image as well as to display a calendar. Refer to the Owner’s Manual Supplement for Monitor System for further details.

. Navigation system main unit

⁄0 Eject button

Depressing this button ejects the DVD-ROM disc.

⁄1 Disc insertion slot

Load a DVD-ROM disc into the system’s main unit through this slot. Inserting an edge of the disc in the slot causes it to be drawn in automatically.

⁄2 Reset button

You can use this button in the event of a problem. It is also used when you need to upgrade the program.

NOTE

• The navigation system main unit is located under the driver's seat.

• Before you load a DVD-ROM disc for the first time, press the reset button for more than one second. Use the tip of a pen or similar item for this purpose.

• If a malfunction occurs during operation, try pressing the reset button. The system may recover from the problem.

System Components and Controls

Starting Up the Navigation System

Use the following procedure to start up the navigation system and display the current map screen.

Start the engine.

The CAUTION screen will appear, followed by the opening screen.

Starting Up the Navigation System

Carefully read the instructions on the CAUTION screen (cited below), then select .

CAUTION

Make selections only when vehicle is stopped. Watching screen while driving can lead to a serious accident. Some map data may be incorrect. Use judgment and obey traffic rules. See Owner’s Manual for complete operating instructions.

The current map screen will appear.

NOTE

• To make a selection, touch the desired key displayed on the screen.

• The CAUTION screen remains on the display unless you select .

• When you use the navigation system for the first time, Greenwich Mean Time will be displayed. Adjust the system’s clock to the right time using the clock setting screen (“SET CLOCK”) as described on Page 82.

Volume

Use this function if you want to change the voice guidance volume setting from the default setting.

Press the button or select on the current map screen.

Select (Volume).

Select the desired key from between (minimum) and (maximum).

(off): Select this key to mute the sound.

Markers and Controls Displayed on Maps

Screens During Route Setting

Touch a point on the map. A crosshair (scroll mark) will appear on the screen. Then touch a desired point on the map. The map will scroll with the selected point at the center.

Press button to return to the current map screen.

Scroll the map

1 Time

Indicates the current time.

2 GPS marker

Shows the status of the signal from GPS satellites. When this marker appears, your navigation system is receiving GPS signals and using them to calculate the position of your vehicle.

3 Map orientation control

Used to select either a “north up” display or “heading up” display of the map. (See Page 18.)

4 Zoom-out/zoom-in control and map scale

The up-pointing or down-pointing arrow is used to zoom out or zoom in the map. The number indicates the scale of the displayed map. The button also provides the zooming function.

5 Menu control

Select this key to display the menu screen. (See Page 16.)

6 Screen configuration control

Allows you to select a preferred display type for route guidance. (See Page 47.)

7 Vehicle marker

Indicates the current position and direction of your vehicle.

Markers and Controls Displayed on Maps

8 “Store memory point” key

Stores markers on the map. This key appears just for a few seconds after a map screen is selected.

9 Point of interest (POI) key

Allows you to display the POI selection screen (see Page

108). On the screen, you can program POIs to appear on a map as markers. This key appears just for a few seconds after a map screen is selected.

0 Distance from current position

Indicates the distance from the current position to the position marked by .

- Destination/waypoint key

Used to program a destination or waypoint at the position marked by on a scroll screen.

Screens During Route Guidance

Select the screen(5 seconds)

Markers and Controls Displayed on Maps

1 Distance and time to destination

Indicates the time (either approximate time required or time of arrival) and the distance to the destination or a waypoint.

2 Route

A thick green line indicates the route you should follow.

3 Turn guidance arrow

Indicates the direction of your turn at the next intersection/junction as well as the distance to the intersection/junction.

4 “Repeat voice” key

If this key is selected, the last voice guidance will be repeated.

5 Current road name

Shows the name of the road you are currently driving on.

6 “Display whole route” key

If this key is selected, a map containing the entire route will be displayed. (See Page 65.)

7 “Change route” key

Selecting this key displays the route option menu. Selecting a new route option causes the system to calculate the selected route.

Menu Screen Keys and Functions

Press button or select to display the menu screen.

Select to return to the current map screen.

The table below shows the keys displayed on the navigation menu (NAV. MENU) screen, the functions accessible by selecting these keys, and the pages of this manual that describe the instructions you should follow when using these functions.

Menu Screen Keys and Functions

Menu screen key Function Reference

page

Destination Entry Address page 26

Point of Interest page 32

Select from Map page 35

Emergency page 38

Memory Point page 29

Previous Destination page 34

Intersection page 42

Freeway Ent/Exit page 36

Phone Number page 44

Coordinates page 40

Stored Locations Memory Points page 89

Avoid Area page 97

Dest. & Way Pt. page 57

Home page 100

Previous Dest. page 102

Preset Dests. page 104

Volume Volume page 12

Navigation Set Up User Settings page 71

Quick POI Selection page 74

Language Selection page 76

Navigation Information page 77

Calibration page 79

Set Clock page 82

Restore System Defaults page 84

Route Options Search Condition page 54

Detour page 55

Route Pref. page 56

Dest. & Way Pt. page 57

Display Route page 65

Route Preview page 66

Map Operations

Selecting Map Orientation

You can select either “heading up” or “north up” display on the current map screen by using the following procedure.

<“Heading up” display>

<“North up” display>

Select or .

If you select (“heading up” display), the system rotates the map so that the direction in which you are heading is always directly upwards on the screen (the red arrow points to the north).

If you select (“north up” display), the system rotates the map so that north is always directly upwards on the screen.

Changing Map Scale

You can increase or decrease the scale of the map using the following procedure:

Map Operations

Select or to change the map scale.

The button also allows you to change the map scale.

Selecting or (or operating the button) changes the scale as shown to the left.

Map Operations

Imperial display

128 mi (mile)

16 mi (mile)

2 mi (mile)

1/4 mi (mile)

1/32 mi (mile)

Metric display

256 km

32 km

4 km

500 m

50 m

Position

before

change

NOTE

• You can keep selecting or (or operating the button) to continually change the map scale.

• If you touch an appropriate point on the right side of the scale bar after selecting or (operating the button), you can choose directly from any of the five scales.

• The scale can be displayed in Imperial or metric units. To change the units, see Page 71.

Setting Route

Setting Destination

Setting destination/waypoints by scrolling the map

Even if you do not know the exact address of your destination or a waypoint on your route to the destination, you can set it by scrolling the map as follows:

Touch the screen and scroll the map until the crosshair reaches the destination or a waypoint.

Select the (destination or waypoint) key.

The key will separate into the destination key and the waypoint key.

Setting Route

Select for setting the destination.

The system will calculate the route and display the entire route to the destination on the map.

Select for a waypoint. The system will program the address of the waypoint on your route (see Page 86). You can set up to 5 waypoints per trip.

Select (start).

Route guidance will begin along the displayed route.

NOTE

• If the system cannot find your desired route, select (change route). This will allow you to access the ROUTE OPTIONS screen, from which you can prompt the system to calculate a new route. (See Page 52.)

• Selecting for more than ten seconds will start the demonstration mode operation. Press the button or select to cancel the demonstration mode.

Setting Route

■ Selecting route

Upon setting the destination, the system prepares to calculate three types of routes to the destination (Quick, Alt., and Short). You can select from any of the three options as follows:

Select (3 routes).

The system will be ready for calculation of any route you select from the three options, namely, Quick (the fastest route), Alt. (alternative route), and Short (the shortest route).

Select (information).

The screen will display details (required time, total distance, roads used, etc.) regarding each option.

Select , , or as you desire, and then select to confirm your selection.

Setting Route

Setting the destination from the navigation menu

You can set your destination using a variety of methods if you start setting from the navigation menu screen. Before you can use any of these methods, perform the following steps:

Press the button or select .

Press the button or select (destination entry).

Setting Route

NOTE

• If the set destination area is different from the one displayed under “Search Area” in the right part of the screen, you must select the (change) key and specify the desired area again.

• For the methods marked with an asterisk ( * ), you can use the “Change Search Area” function to narrow the area where a destination

or waypoint is located by selecting the (change) key (see Page 46).

• Depending on the method used or the status of the map displayed, the located point may differ from where the facility you want to

visit actually exists.

Select the method you want to use.

(Address)* See Page 26.

(Point of Interest)* See Page 32.

(Select from Map) See Page 35.

(Emergency) See Page 38.

(Memory Point) See Page 29.

(Previous Destination) See Page 34.

(Intersection)* See Page 42.

(Freeway Ent/Exit) See Page 36.

(Phone number) See Page 44.

(Coordinates) See Page 40.

(Home) See Page 31.

You can switch between screens by selecting (next page) or (previous page).

Setting Route

■ “Address” method

First, choose either of the two procedures below to follow the “address” method.

• Press the button or select , select (destination entry), and then select (address).

• Press the button and select (address).

Enter a house number using the keypad on the house number input screen and select .

Enter the street name.

If you enter enough letters to identify a street name and advance to Step 3, a list showing several street names will be displayed. Select the desired street name from the list.

: Use this key to delete the last character entered. Select it repeatedly if you

want to delete all the characters entered.

You can switch between keypad screens showing different characters by selecting

(others), (symbols) or (alphabet).

Setting Route

Select (list).

Select the desired street from the list.

If the same street name exists in more than one city, a list of these cities will be shown.

Select the correct city from the list.

: Use this key to input the city name from the keypad.

Setting Route

NOTE

• If your DVD-ROM disc does not contain the relevant house number data, an error message will be displayed and a street map will appear, allowing you to set the destination using the map.

• If your destination is not on a road, set a destination point on a main road nearest to your true destination.

• Selecting the will display a screen that searches the destination on a city basis.

: Search the destination from all cities. : Search the destination from the nearby five cities within 20 miles from the current

position.

: Search the destination by inputting the city name.

You can also search the destination from the five cities that you searched in the past.

Select (destination) to set the address entered in the above steps as your final destination.

The system will calculate the route and display the entire route on the map.

Select (waypoint) to set the address entered in the above steps as a waypoint on your route.

You can program up to five waypoints per trip.

Select (start).

Route guidance begins along the displayed route.

Setting Route

■ “Memory Point” method

If you have saved some locations in the system’s memory, you can make use of an appropriate one to set the destination.

First, choose either of the two procedures below to follow the “memory point” method.

• Press the button or select , select (destination entry), and then select (memory point).

• Press the button and select (memory point).

Select the category to which the address of the desired location (memory point) is classified in the memory.

Select the address of the desired location (memory point).

: Use this key to display up to five previous suggestions. : Use this key to display the previous suggestion. : Use this key to display the next suggestion. : Use this key to display up to five of the next suggestions.

+ 96 hidden pages