Structural Concepts Oasis Mobile Series, B4732D, B3632D, B5932D, B7132D Installation & Operating Manual
...
READ AND SAVE THESE INSTRUCTIONS
®
M O B I L E S E R I E S
INSTALLATION &
OPERATING MANUAL
SCC P/N
20-42840
Oasis® 32” Deep Non-Refrigerated Self-Service In-Aisle Grab-N-Go Wall Units
Model B4732 Shown With
Optional Roll-Down Security Cover
888 E. Porter Road · Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com
I:\Oper Manuals\Oasis\B4732D_In_Aisle_Ambient_Wall_Unit_20-42840.pub
Model B4732DShown Without
Optional Roll-Down Security Cover
:
:
:
:
:
*Lengths include end panels.
Rev B Date: 6.11.2016
TABLE OF CONTENTS / MODELS and DIMENSIONS
OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS ..………....
INSTALLATION: CASE REMOVAL / POSITIONING & ALIGNING CASE .……………………………..
FRONT PANEL ACCESS / MAIN POWER SWITCH ……………………………………………………….
POWER CORD / FIELD ACCESS & ELECTRICAL BOX / BALLASTS …………………………………
LIGHT FIXTURES - T8 FLUORESCENTS …………………………………………………………………...
LIGHT FIXTURES - LEDs ………..…………………………………………………………………………….
OPTIONAL ROLL-DOWN SECURITY COVER ..…………………………………………………...……….
CLEANING SCHEDULE (TO BE PERFORMED BY STORE PERSONNEL) …..……..……....………..
TROUBLESHOOTING (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY) .………
SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE ……….…..……...
TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION …...……....…….
3
4
5
6
7
8
9
10
11
12
13
2
OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS
OVERVIEW
These Structural Concepts merchandisers are
designed to merchandise packaged products at
ambient temperatures.
Cases should be installed and operated according to
this operating manual’s instructions to insure proper
performance. Improper use will void warranty.
CASE TYPE
This unit is designed for the display of products in ambient
store conditions where temperatures and humidity are
maintained within a specific range.
For Type 1 Conditions (most cases): ambient
conditions are to be at 55% maximum humidity and
maximum temperatures of 75 °F (24 °C).
For Type 2 Conditions: ambient conditions are to be
at 60% maximum humidity and maximum
temperatures of 80 °F (27 °C).
This equipment MUST be installed in compliance with
all applicable NEC, federal, state and local electrical codes.
If unsure if unit is designed for Type 1 or 2, see tag
next to serial label. See SERIAL LABEL LOCATION
& INFORMATION LISTED / TECH INFO & SERVICE
section in this manual for sample serial labels.
COMPLIANCE
Performance issues when in violation of applicable
NEC, federal, state and local electrical and plumbing
codes are not covered by warranty.
WARNINGS
This sheet contains important warnings to prevent
injury or death.
Please read carefully!
PRECAUTIONS, CORD/PLUG MAINTENANCE &
WIRING DIAGRAM INFORMATION
See next page for PRECAUTIONS, CORD/PLUG
MAINTENANCE and WIRING DIAGRAM information.
COMPLIANCE
WARNING
ELECTRICAL
HAZARD
CAUTION
WARNING
Risk of electric shock. Disconnect power before servicing unit.
CAUTION! More than one source of electrical supply is
employed with units that have separate circuits.
Disconnect ALL ELECTRICAL SOURCES before servicing.
CAUTION! LAMP REPLACEMENT GUIDELINES
LED lamps reflect specific size, shape and overall design.
Any replacements must meet factory specifications.
Hera® / Fluorescent lamps have been treated to resist breakage
and must be replaced with similarly treated lamps.
CAUTION! GFCI BREAKER USE REQUIREMENT
If N.E.C. (National Electric Code) or your local code
requires GFCI (Ground Fault Circuit Interrupter) protection,
you MUST use a GFCI breaker in lieu of a GFCI receptacle.
CAUTION! POWER CORD AND PLUG MAINTENANCE
Risk of electric shock. If cord or plug becomes damaged,
replace only with cord and plug of same type.
3
INSTALLATION: CASE REMOVAL / POSITIONING & ALIGNING CASE
1. Remove Case From Skid (Levelers)
Remove shipping brace that may be securing
case to skid.
Support case to prevent tipping.
Caution! Levelers can be damaged if case hits
floor with heavy force!
Carefully slide unit
to rear of skid and
tip backward off
skid.
Illustration may
not reflect every
feature or option
of your particular
case.
Slide Skid Out
Case can be repositioned with pallet truck when front lower
panel is removed. Blocking may be necessary to obtain
adequate height.
2. Remove Case From Skid (Casters)
Remove shipping brackets that may be securing
casters to skid
Place ramp up against skid (to allow case to
smoothly slide off from skid).
Maintain support of case at all times or center
of gravity may cause case to fall.
Unlock Casters. Roll unit to rear of skid.
Roll down ramp
and off from skid.
Note: Illustrations
shown reflect a
general outline of
sample cases and
do not reflect
features or
options of your
particular model.
Ramp
Support
while
rolling
case
down
ramp.
3. Position & Align Case Alongside Other
Cases
Before adjusting levelers, make certain that the
case is in proper position and, if required, aligned
with adjoining case(s).
This may require the repositioning of the case you
are installing or
4. Adjust Levelers
After case is in proper position, adjust case so it is
level and plumb (see illustration at right).
You may need to remove front and/or rear
Toe-Kick to access levelers.
Use adjustable wrench to adjust leveler.
Depending upon case weight it may be necessary
to use a Pry Bar to accomplish this task.
Do not use Pry Bar on Toe-Kick as it may buckle.
Do not use Pry Bar on End Panel as it may chip.
Use Pry Bar ONLY on Base Frame to avoid
damaging case.
See illustration and photos at right.
the already positioned case(s).
Pry Bar
Adjustable
Wrench
Leveler
Base
Frame
Toe-Kick
4
Loading...