STMicroelectronics NUCLEO-F756ZG, NUCLEO-L4R5ZI-P User Manual

Page 1

UM2179

User manual

STM32 Nucleo-144 boards (MB1312)

Introduction

The STM32 Nucleo-144 boards based on the MB1312 reference board (NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI, NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG) provide an affordable and flexible way for users to try out new concepts and build prototypes with STM32 microcontrollers, choosing from the various combinations of performance, power consumption and features. The ST Zio connector, which extends the ARDUINO Uno V3 connectivity, and the ST morpho headers make it easy to expand the functionality of the Nucleo open development platform with a wide choice of specialized shields. The STM32 Nucleo-144 boards do not require any separate probe as they integrate the STLINK/V2-1 debugger/programmer. The STM32 Nucleo-144 boards come with the STM32 comprehensive free software libraries and examples available with the STM32Cube MCU Package.

Figure 1. Nucleo-144 board (top view) Figure 2. Nucleo-144 board (bottom view)

Pictures are not contractual..

September 2019 UM2179 Rev 8 1/55

www.st.com

Page 2

Contents UM2179

Contents

1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Product marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Codification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 Development toolchains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.1 STM32 Nucleo-144 board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5.2 STM32 Nucleo-144 board mechanical drawing . . . . . . . . . . . . . . . . . . . . 14

5.3 Cuttable PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.4 Embedded ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.4.1 Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.4.2 ST-LINK/V2-1 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.4.3 Using the ST-LINK/V2-1 to program and debug the on-board STM32 . 17

5.4.4 Using ST-LINK/V2-1 to program and debug an external STM32

application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.5 Power supply and power selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.5.1 Power supply input from ST-LINK/V2-1 USB connector . . . . . . . . . . . . 21

5.5.2 External power supply inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.5.3 External power supply output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.5.4 SMPS power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.6 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.7 Push-buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.8 JP5 (IDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.9 OSC clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2/55 UM2179 Rev 8

Page 3

UM2179 Contents

5.9.1 OSC clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.10 OSC 32 KHz clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.11 LPUART1 communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.12 USB FS OTG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.13 Solder bridges and jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.14 Expansion connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.15 ST Zio connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.16 ST morpho connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.17 Bootloader limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5.17.1 Bootloader operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5.17.2 Bootloader identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.17.3 Bootloader limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.17.4 Affected parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.17.5 Workarounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Appendix A Electrical schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Appendix B Board revision history and limitations . . . . . . . . . . . . . . . . . . . . . . 51

Appendix C Federal Communications Commission (FCC)

and Industry Canada (IC) Compliance . . . . . . . . . . . . . . . . . . . . . . . 52

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

UM2179 Rev 8 3/55

Page 4

List of tables UM2179

List of tables

Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2. Codification explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 3. ON/OFF conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 4. CN4 states of the jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 5. Debug connector CN5 (SWD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 6. External power sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 7. Power related jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 8. LPUART1 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 9. USB pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 10. Configuration of the solder bridges and jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 11. NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI,

NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments . . . . . . . . . . . . . . . . . . . . . . 38

Table 12. ST morpho connector pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 13. Board revision history and limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 14. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4/55 UM2179 Rev 8

Page 5

UM2179 List of figures

List of figures

Figure 1. Nucleo-144 board (top view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2. Nucleo-144 board (bottom view). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 3. Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 4. STM32 Nucleo-144 board top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 5. STM32 Nucleo-144 board bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 6. STM32 Nucleo-144 board mechanical drawing in millimeter . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 7. Nucleo-144 board mechanical drawing in mils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 8. USB composite device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 9. Connecting the STM32 Nucleo-144 board to program the on-board STM32. . . . . . . . . . . 18

Figure 10. Using ST-LINK/V2-1 to program an external STM32 application . . . . . . . . . . . . . . . . . . . . 20

Figure 11. NUCLEO-L496ZG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 12. NUCLEO-L496ZG-P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 13. NUCLEO-L4A6ZG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 14. NUCLEO-L4R5ZI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 15. NUCLEO-L4R5ZI-P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 16. Top and power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 17. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 18. ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 19. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 20. Extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 21. SMPS power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

UM2179 Rev 8 5/55

Page 6

Features UM2179

1 Features

The STM32 Nucleo-144 boards offer the following common features:

• STM32 Arm®-based microcontroller in LQFP144 package

• USB OTG FS

• 3 user LEDs

• 2 user and reset push-buttons

• 32.768 kHz crystal oscillator

• Board connectors:

– USB with Micro-AB

–SWD

– ST Zio expansion connector including ARDUINO

– ST morpho expansion connector

• Flexible power-supply options: ST-LINK, USB V

• On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability:

mass storage, Virtual COM port and debug port

• Comprehensive free software libraries and examples available with the STM32Cube MCU Package

• Support of a wide choice of Integrated Development Environments (IDEs) including

™

IAR

, Keil®, GCC-based IDEs

Uno V3

or external sources

BUS

Additionally, some STM32 Nucleo-144 boards offer the following specific features:

• External SMPS to generate V

• Arm® Mbed Enabled™

a. SMPS significantly reduces power consumption in Run mode, by generating V

DC/DC converter.

b. Arm and Mbed are registered trademarks or trademarks of Arm Limited (or its subsidiaries) in the US and or

elsewhere.

(b)

compliant

logic supply

core

(a)

logic supply from an external

core

6/55 UM2179 Rev 8

Page 7

UM2179 Ordering information

2 Ordering information

To order an STM32 Nucleo-144 board, refer to Tab le 1. Additional information is available from the datasheet and reference manual of the target STM32.

Order code Board reference Target STM32 Differentiating features

NUCLEO-L496ZG

NUCLEO-L496ZG-P STM32L496ZGT6PU – External SMPS

Table 1. Ordering information

STM32L496ZGT6U – Arm

Mbed Enabled™

NUCLEO-L4A6ZG STM32L4A6ZGT6U – Cryptography

NUCLEO-L4R5ZI STM32L4R5ZIT6U – Arm

NUCLEO-L4R5ZI-P STM32L4R5ZIT6PU

2.1 Product marking

Evaluation tools marked as “ES” or “E” are not yet qualified and therefore not ready to be used as reference design or in production. Any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering sample tools as reference design or in production.

“E” or “ES” marking examples of location:

• On the targeted STM32 that is soldered on the board (for illustration of STM32 marking, refer to the STM32 datasheet “Package information” paragraph at the www.st.com website).

• Next to the evaluation tool ordering part number that is stuck or silk-screen printed on the board.

The boards feature a specific STM32 device version, which allows the operation of any bundled commercial stack/library available. This STM32 device shows a "U" marking option at the end of the standard part number and is not available for sales.

In order to use the same commercial stack in his application, a developer may need to purchase a part number specific to this stack/library. The price of those part numbers includes the stack/library royalties.

MB1312

Mbed Enabled™

–Arm – External SMPS

Mbed Enabled™

UM2179 Rev 8 7/55

Page 8

Ordering information UM2179

2.2 Codification

The meaning of the codification is explained in Tabl e 2.

NUCLEO-XXYYZT(-P) Description Example: NUCLEO-L496ZG-P

XX MCU series in STM32 Arm Cortex MCUs STM32L4 Series

YY MCU product line in the series STM32L496

Z STM32 package pin count 144 pins

-P STM32 has external SMPS function External SMPS

The order code is mentioned on a sticker placed on the top side of the board.

Table 2. Codification explanation

STM32 Flash memory size: – G for 1 Mbyte – I for 2 Mbytes

1 Mbyte

8/55 UM2179 Rev 8

Page 9

UM2179 Quick start

3 Quick start

This section describes how to start a development quickly using the STM32 Nucleo-144 board.

Before installing and using the product, accept the Evaluation Product License Agreement from the www.st.com/epla webpage. For more information on the STM32 Nucleo-144 board and for demonstration software, visit the www.st.com/stm32nucleo webpage.

3.1 Getting started

Follow the sequence below to configure the Nucleo-144 board and launch the demonstration application (for components location refer to

1. Check the jumper position on the board: JP1 (PWR-EXT) OFF (see Section 5.5.1: Power supply input from ST-LINK/V2-1 USB

connector for more details)

JP6 (Power source) on STLK side (for more details see Table 7: Power related jumper) JP5 (IDD) ON (for more details see Section 5.8: JP5 (IDD)) CN4 ON selected (for more details see Table 4: CN4 states of the jumpers).

2. For the correct identification of the device interfaces from the host PC and before connecting the board, install the Nucleo USB driver available on the www.st.com/stm32nucleo website.

3. To power the board connect the STM32 Nucleo-144 board to a PC with a USB ‘Type-A to Micro-B’ cable through the USB connector CN1 on the ST-LINK. As a result, the green LED LD6 (PWR) and LD4 (COM) light up and the red LED LD3 blinks.

4. Press button B1 (left button).

5. Observe that the blinking frequency of the three LEDs LD1 to LD3 changes, by clicking on

the button B1.

6. The software demonstration and the several software examples, that allow the user to use the Nucleo features, are available at the www.st.com/stm32nucleo webpage.

7. Develop an application, using the available examples.

Figure 4: STM32 Nucleo-144 board top layout).

3.2 System requirements

• Windows® OS (7, 8 and 10), Linux® 64-bit or macOS

• USB Type-A to Micro-B cable

3.3 Development toolchains

• Keil® MDK-ARM

• IAR™ EWARM

• GCC-based IDEs

• Arm

a. macOS® is a trademark of Apple Inc., registered in the U.S. and other countries

b. On Windows® only.

Mbed™ online (see https://mbed.org)

(b)

UM2179 Rev 8 9/55

®(a)

Page 10

Conventions UM2179

3.4 Demonstration software

The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board MCU, is preloaded in the STM32 Flash memory for easy demonstration of the device peripherals in standalone mode. The latest versions of the demonstration source code and associated documentation can be downloaded from the www.st.com/stm32nucleo webpage.

4 Conventions

Tab le 3 provides the conventions used for the ON and OFF settings in the present

document.

Convention Definition

Jumper JPx ON Jumper fitted

Jumper JPx OFF Jumper not fitted

Solder bridge SBx ON SBx connections closed by solder or 0 ohm resistor

Table 3. ON/OFF conventions

Solder bridge SBx OFF SBx connections left open

In this document the references for all information that is common to all sale types, are “STM32 Nucleo-144 board” and “STM32 Nucleo-144 boards”.

10/55 UM2179 Rev 8

Page 11

UM2179 Hardware layout and configuration

Embedded

ST-LINK/V2-1

STM32

Microcontroller

RESET

SWD

ST ŵorpho extension Header

Micro-B

USB

Đonnector

USB

RST

USER

Zio Đonnector

LED

LD1

ST-LINK Part

MCU Part

LED

LD2/3

Micro-AB or

Micro-B USB

Đonnector

Zio Đonnector

Ext

SMPS

5 Hardware layout and configuration

The STM32 Nucleo-144 board is designed around the STM32 microcontrollers in a 144-pin LQFP package.

Figure 3 shows the connections between the STM32 microcontroller and its peripherals (ST-

LINK/V2-1, push-buttons, LEDs, USB, ST Zio connectors and ST morpho headers).

Figure 4 and Figure 5 show the location of these features on the STM32 Nucleo-144 board. Figure 6 and Figure 7 show the mechanical dimensions of the STM32 Nucleo-144 board.

Figure 3. Hardware block diagram

1. Ext SMPS function is only available on '-P' suffixed boards.

UM2179 Rev 8 11/55

Page 12

Hardware layout and configuration UM2179

CN1 ST

LINK Micro

USB connector

CN4 ST

-LINK/

NUCLEO selector

LD1-LD3 User LEDs

B1 User button

CN11

ST Porpho

pin header

CN13 SMPS signal connector

JP1 PWR

EXT

CN5 SWD connector

JP5 IDD measurement

U11 STM32 Microcontroller

LD7

USB over

CN7, CN10 Zio connectors

SB6

3.3V regulator output

JP6 Power Source selection

LD6 Power (Green LED)

LD5

(Red LED) ST-/,1.9 Power Over

FXUUHQWDODUP

LD4 (Red/Green LED) COM

LD8

USB VBUS

CN14 User USB connector

B2 Reset button

CN8, CN9 Zio connectors

CN12

ST Porpho

pin header

5.1 STM32 Nucleo-144 board layout

Figure 4. STM32 Nucleo-144 board top layout

12/55 UM2179 Rev 8

Page 13

UM2179 Hardware layout and configuration

SB101, SB103, SB105, SB107 (RESERVED)

SB100, SB102, SB104, SB106 (DEFAULT)

Figure 5. STM32 Nucleo-144 board bottom layout

UM2179 Rev 8 13/55

Page 14

Hardware layout and configuration UM2179

5.2 STM32 Nucleo-144 board mechanical drawing

Figure 6. STM32 Nucleo-144 board mechanical drawing in millimeter

14/55 UM2179 Rev 8

Page 15

UM2179 Hardware layout and configuration

Figure 7. Nucleo-144 board mechanical drawing in mils

UM2179 Rev 8 15/55

Page 16

Hardware layout and configuration UM2179

5.3 Cuttable PCB

The STM32 Nucleo-144 board is divided into two parts: ST-LINK and target STM32. The ST-LINK part of the PCB can be cut out to reduce the board size. In this case the remaining target STM32 part can only be powered by V CN11, or by V

and 3.3 V on the ST Zio connector CN8. It is still possible to use the ST-

, E5V and 3.3 V on the ST morpho connector

LINK part to program the STM32, using wires between the CN5 and SWD available signals on the ST morpho connector (SWCLK CN11 pin 15, SWDIO CN11 pin 13 and NRST CN11 pin 14, same I/O level as VDD_MCU).

5.4 Embedded ST-LINK/V2-1

The ST-LINK/V2-1 programming and debugging tool is integrated in the STM32 Nucleo-144 board.

The embedded ST-LINK/V2-1 supports only SWD for STM32 devices. For information about debugging and programming features refer to the ST-LINK/V2 in-circuit

debugger/programmer

for STM8 and STM32 user manual (UM1075), which describes in

details all the ST-LINK/V2 features.

The changes versus ST-LINK/V2 version are listed below. New features supported on STLINK/V2-1:

• USB software re-enumeration

• Virtual COM port interface on USB

• Mass storage interface on USB

• USB power management request for more than 100 mA power on USB

Features not supported on ST-LINK/V2-1:

• SWIM interface

• Minimum supported application voltage limited to 3 V

There are two different ways to use the embedded ST-LINK/V2-1, depending on the jumper state (see Table 4):

• Program/debug the STM32 on board

• Program/debug the STM32 in an external application board, using a cable connected

SWD connector CN5

Jumper state Description

Table 4. CN4 states of the jumpers

Both CN4 jumpers ON

Both CN4 jumpers OFF

16/55 UM2179 Rev 8

ST-LINK/V2-1 functions enabled for on-board programming (default). See Section 5.4.3.

ST-LINK/V2-1 functions enabled for external CN5 connector (SWD supported). See Section 5.4.4.

Page 17

UM2179 Hardware layout and configuration

5.4.1 Drivers

Before connecting the Nucleo-144 board to a Windows® (XP, 7, 8 and 10) PC via USB, install the driver for ST-LINK/V2-1 that can be downloaded from the www.st.com website.

If the STM32 Nucleo-144 board is connected to the PC before installing the driver, the PC device manager may report some Nucleo interfaces as “Unknown”.

To recover from this situation, after installing the dedicated driver, the association of “Unknown” USB devices found on the STM32 Nucleo-144 board to this dedicated driver, must be updated in the device manager manually.

Note: It is recommended to proceed by using USB Composite Device, as shown in Figure 8.

Figure 8. USB composite device

5.4.2 ST-LINK/V2-1 firmware upgrade

The ST-LINK/V2-1 embeds a firmware upgrade mechanism for in-situ upgrade through the USB port. As the firmware may evolve during the lifetime of the ST-LINK/V2-1 product (for example new functionalities, bug fixes, support for new microcontroller families), it is recommended to keep the ST-LINK/V2-1 firmware up to date before starting to use the STM32 Nucleo-144 board. The latest version of this firmware is available from the

www.st.com website.

5.4.3 Using the ST-LINK/V2-1 to program and debug the on-board STM32

To program the on-board STM32, place the two jumpers marked in red on the connector CN4, as shown in Figure 9. The CN5 connector must not be used, since it could disturb the communication with the STM32 microcontroller of the Nucleo-144 board.

UM2179 Rev 8 17/55

Page 18

Hardware layout and configuration UM2179

06Y9

&1MXPSHUV21

&16:'

FRQQHFWRU

Figure 9. Connecting the STM32 Nucleo-144 board to program the on-board STM32

5.4.4 Using ST-LINK/V2-1 to program and debug an external STM32 application

It is very easy to use the ST-LINK/V2-1 to program the STM32 on an external application.

Simply remove the two jumpers from CN4, as shown in Figure 10 and connect the application to the SWD debug connector according to Table 5.

Note: JP4 NRST (target STM32 RESET) must be open when CN3 pin 5 is used in an external

application.

18/55 UM2179 Rev 8

Page 19

UM2179 Hardware layout and configuration

Table 5. Debug connector CN5 (SWD)

Pin CN5 Description

1 VDD_TARGET V

from application

2 SWCLK SWD clock

3 GND ground

4 SWDIO SWD data input/output

5 NRST RESET of target STM32

6SWOReserved

UM2179 Rev 8 19/55

Page 20

Hardware layout and configuration UM2179

06Y9

&1MXPSHUV2))

&16:'

FRQQHFWRU

Figure 10. Using ST-LINK/V2-1 to program an external STM32 application

20/55 UM2179 Rev 8

Page 21

UM2179 Hardware layout and configuration

5.5 Power supply and power selection

The power supply is provided either by the host PC through the USB cable or by an external source: VIN (7 V-12 V), E5V (5 V) or +3.3 V power supply pins on CN8 or CN11. If VIN, E5V or +3.3 standard EN-60950-1: 2006+A11/2009 and must be Safety Extra Low Voltage (SELV) with limited power capability.

If the power supply is +3.3 V, the ST-LINK is not powered and cannot be used.

V is used to power a Nucleo-144 board, this power source must comply with the

5.5.1 Power supply input from ST-LINK/V2-1 USB connector

The STM32 Nucleo-144 board and shield can be powered from the ST-LINK USB connector CN1 (U5V), by placing a jumper between the pins 3 and 4 of JP6, as shown in

Power related jumper. Note that only the ST-LINK part is power supplied before the USB

enumeration, as the host PC only provides 100 mA to the board at that time. During the USB enumeration, the STM32 Nucleo-144 board requires 300 If the host is able to provide the required power, the targeted STM32 microcontroller is powered and the green LED LD6 is turned ON, thus the STM32 Nucleo-144 board and its shield can consume a maximum current of 300 provide the required current, the targeted STM32 microcontroller and the extension boards are not power supplied. As a consequence the green LED LD6 stays turned OFF. In such case it is mandatory to use an external power supply as explained in the next section.

After the USB enumeration succeeds, the ST-LINK U5V power is enabled, by asserting the PWR_EN pin. This pin is connected to a power switch (ST890), which powers the board.

This power switch also features a current limitation to protect the PC if a short-circuit happens on the board. If an overcurrent (more than 500 lits up.

mA, not more. If the host is not able to

mA) happens on the board, the red LED LD5

mA of current to the host PC.

Table 7:

Warning: If the maximum current consumption of the STM32 Nucleo-

144 board and its shield boards exceed 300 mA, it is mandatory to power the STM32 Nucleo-144 board, using an external power supply connected to E5V, VIN or +3.3 V.

Note: If the board is powered by a USB charger, there is no USB enumeration, so the green LED

LD6 stays in OFF state permanently and the target STM32 is not powered. In this specific case a jumper must be placed between pins 5 and 6 of JP6, to allow the board to be powered anyway.

5.5.2 External power supply inputs

Depending on the used voltage, an external power source supplies in three different ways the STM32 Nucleo-144 board and its shield boards. The three power sources are listed in

Table 6.

When the STM32 Nucleo-144 board is power supplied by VIN or E5V, the jumper configuration must be as showed below:

• Jumper JP6 on pin 1 and pin 2 for E5V or jumper JP3 on pin 7 and pin 8 for V

• Jumper JP1 OFF

UM2179 Rev 8 21/55

Page 22

Hardware layout and configuration UM2179

E5V

STLK

CHGR VIN

E5V

STLK

CHGR VIN

E5V

STLK

CHGR VIN

E5V

STLK

CHGR VIN

Input power

name

Connector

pins

Table 6. External power sources

Vol tag e

range

Max current Limitation

From 7 V to 12 V only and input current capability is linked to input voltage:

CN8 pin 15

CN11 pin 24

7 V to 12 V 800 mA

– 800 mA input current when

=7 V

– 450 mA input current when

7V<V

<9V

– 250 mA input current when

<12 V

E5V CN11 pin 6

4.75 V to

5.25 V

9 V<V

500 mA -

Two possibilities:

+3.3 V

CN8 pin 7

CN11 pin 16

3 V to 3.6 V -

–ST-LINK PCB is cut – SB3 and SB111 OFF (ST-LINK not

powered)

The 5 V power source is selected by the jumper JP6 as shown in Table 7.

Table 7. Power related jumper

Jumper Description

STLK (ST-LINK V

) is used as power source when JP6 is set as shown on the

BUS

right (Default setting)

E5V is used as power source when JP6 is set as shown on the right:

JP6

CHGR (USB Charger on CN1) is used as power source when JP6 is set as shown on the right:

is used as power source when JP6 is set as shown on the right:

22/55 UM2179 Rev 8

Page 23

UM2179 Hardware layout and configuration

Using VIN or E5V as an external power supply

When powered by VIN or E5V, it is still possible to use the ST-LINK for only programming or debugging, but it is mandatory to power the board first using VIN or E5V, then to connect the USB cable to the PC. In this way the enumeration succeeds, thanks to the

external power

source.

The following power-sequence procedure must be respected:

1. Connect jumper JP6 between pin 1 and pin 2 for E5V or between pin 7 and pin 8 for V

2. Check that JP1 is removed

3. Connect the external power source to VIN or E5V

4. Power on the external power supply 7 V< VIN < 12 V to VIN, or 5 V for E5V

5. Check that the green LED LD6 is turned ON

6. Connect the PC to the USB connector CN1

If this order is not respected, the board may be powered by USB (U5V) first, then by VIN or E5V as the following risks may be encountered:

1. If the board needs more than 300 mA, the PC may be damaged or the current supplied can be limited by the PC. As a consequence the board is not powered correctly.

2. 300 mA is requested during the enumeration phase (since JP1 must be OFF) so there is the risk that the request is rejected and the enumeration does not succeed if the PC cannot provide such current. Consequently the board is not power supplied (LED LD6 remains OFF).

External power supply input: + 3.3 V

If 3.3 V is provided by a shield board, it is worth using the +3.3 V (CN8 pin 7 or CN11 pin 16) directly as power input. In this case the ST-LINK is not powered thus debugging features are not available.

When the board is powered with +3.3 V, two different configurations are possible:

• ST-LINK is removed (PCB cut)

• SB6 (3.3 V regulator) and JP3 (NRST) are OFF

5.5.3 External power supply output

When powered by USB, VIN or E5V, the +5 V (CN8 pin 9 or CN11 pin 18) can be used as output power supply for an ST Zio shield or an extension board. In this case the maximum current of the power source specified in Tabl e 6: External power sources must be respected.

The +3.3 V (CN8 pin 7 or CN11 pin 16) can also be used as power supply output. The current is limited by the maximum current capability of the regulator U6 (500 mA max).

5.5.4 SMPS power supply

Power figures in Run Mode are significantly improved, by generating V the external DC/DC converter (this function is only available on '-P' suffixed boards).

Board is populated with two different SMPS mounted on U15 and U16:

• SMPS U15 allows to dynamically supply the V maximum current of 30 mA. For the NUCLEO-L4R5ZI-P, the V mode are supplied at 1.2 V with a maximum current of 40 mA.

DD_1V2

the programming and

logic supply from

core

pins in Run mode at 1.1 V with a

DD_1V2

pins in Run

UM2179 Rev 8 23/55

Page 24

Hardware layout and configuration UM2179

• SMPS U16 allows to supply the V

DD_MCU

pins at 1.8 V with a maximum current of 50 mA. When SB125 is opened and SB120 closed, the SMPS can deliver higher current but with higher consumption. This SMPS is disabled by default (See Table 10:

Configuration of the solder bridges and jumpers).

DD_MCU

solder bridge configuration:

• 3.3 V (default): SB122 closed, SB121 and SB127 open

• 1.8 V: SB122 open, and SB121 and SB127 closed (best ULPBench score)

Caution: The power sequence is not respected when using 1V8 MCU_VDD. Refer to the Getting

started with STM32L4 Series and STM32L4+ Series hardware development application

note (AN4555), and to the corresponding STM32L4 Series and STM32L4+ Series product datasheets.

Note: The ST-LINK is still available in this configuration as a result of level shifter U14.

5.6 LEDs

User LD1: a green user LED is connected to the STM32 I/O PC7 (SB124 ON and SB123

OFF) or PA5 (SB123 ON and SB124 OFF) corresponding to the ST Zio D13. It only works when V

CC_MCU

User LD2: a blue user LED is connected to PB7.

User LD3: a red user LED is connected to PB14.

These user LEDs are on when the I/O is HIGH value, and are off when the I/O is LOW.

LD4 COM: the tricolor LED LD4 (green, orange and red) provides information about ST-LINK communication status. LD4 default color is red. LD4 turns to green to indicate that the communication is in progress between the PC and the ST-LINK/V2-1, with the following setup:

• Slow blinking red/off: at power-on before USB initialization

• Fast blinking red/off: after the first correct communication between PC and

ST-LINK/V2-1 (enumeration)

• Red LED on: when the initialization between the PC and ST-LINK/V2-1 is complete

• Green LED on: after a successful target communication initialization

• Blinking red/green: during communication with target

• Green on: communication finished and successful

• Orange on: communication failure

LD5 USB power fault: LD5 indicates that the board power consumption on USB exceeds 500 mA, consequently the user must power the board using an external power supply.

is 3.3 V.

LD6 PWR: the green LED indicates that the STM32 part is powered and +5 V power is available on CN8 pin 9 and CN11 pin 18.

LD7 and LD8 USB FS: refer to Section 5.12: USB FS OTG .

Note:1 LD1 is connected to U8 and it is driven by PC7 or PA5 which may be changed to 1.8 V I/O,

so LD1 cannot be lit when V

Note:2 LD2, LD3 cannot work with V

24/55 UM2179 Rev 8

is set to 1.8 V.

DD_MCU

= 1.8 V

Page 25

UM2179 Hardware layout and configuration

5.7 Push-buttons

B1 USER: the user button is connected to the I/O PC13 by default (Tamper support, SB197

ON and SB178 OFF) or PA0 (Wakeup support, SB178 ON and SB197 OFF) of the STM32.

B2 RESET: this push-button is connected to NRST and is used to RESET the STM32.

5.8 JP5 (IDD)

The jumper JP5, labeled IDD, is used to measure the STM32 microcontroller consumption by removing the jumper and by connecting an ammeter:

• JP5 ON: STM32 is powered (default)

• JP5 OFF: an ammeter must be connected to measure the STM32 current. If there is no

ammeter, the STM32 is not powered

5.9 OSC clock

5.9.1 OSC clock supply

There are four ways to configure the pins corresponding to the external high-speed clock (HSE):

• HSE not used (Default): PF0/PH1 and PF1/PH1 are used as GPIOs instead of as clock. The

– SB147 and SB156 ON

– SB109 and SB148 (MCO) OFF

– SB12 and SB13 removed

• MCO from ST-LINK: MCO output of ST-LINK is used as input clock. This cannot be changed, it is fixed at 8 MHz and connected to the

• PF0/PH0-OSC_IN of STM32 microcontroller. The configuration must be:

–SB147 OFF

– SB109 and SB148 ON

– SB12 and SB13 OFF

• HSE on-board oscillator from X3 crystal (not provided): for typical frequencies and its capacitors and resistors, refer to the STM32 microcontroller datasheet and for the oscillator design guide refer to the Oscillator design guide for STM8S, STM8A and STM32 microcontrollers Application characteristics: 8 MHz, 8 pF, 20 ppm. It is recommended to use the NX3225GD-8.000MEXS00A-CG04874 crystal manufactured by NIHON DEMPA KOGYO CO., LTD. The configuration must be:

– SB147 and SB156 OFF

– SB12 and SB13 soldered

– C37 and C38 soldered with 4.3 pF capacitors

– SB109 and SB148 OFF

configuration must be:

frequency

note (AN2867). The X3 crystal has the following

UM2179 Rev 8 25/55

Page 26

Hardware layout and configuration UM2179

• Oscillator from external PF0/PH0: from an external oscillator through the pin 29 of the CN11 connector. The configuration must be:

–SB147 ON

– SB109 and SB148 OFF

– SB12 and SB13 removed

26/55 UM2179 Rev 8

Page 27

UM2179 Hardware layout and configuration

5.10 OSC 32 KHz clock supply

There are three ways to configure the pins corresponding to low-speed clock (LSE):

• On-board oscillator (Default): X2 crystal. Refer to the Oscillator design guide for STM8S, STM8A and STM32 microcontrollers Application note (AN2867) for oscillator

design guide for STM32 microcontrollers. It is recommended to use the NX3214SA-

32.768KHZ-EXS00A-MU00525 (32.768 KHz, 6 pF load capacitance, 200 ppm) crystal from Nihon Dempa Kogyo CO, LTD.

• Oscillator from external PC14: from external oscillator through the pin 25 of CN11 connector. The configuration must be:

– SB145 and SB146 ON

– R39 and R40 removed

• LSE not used: PC14 and PC15 are used as GPIOs instead of low-speed clock. The configuration must be:

– SB145 and SB146 ON

– R39 and R40 removed

5.11 LPUART1 communication

The LPUART1 interface available on PG7 and PG8 of the STM32 can be connected to the ST-LINK or to the ST morpho connector. Another option to do this connection is to set the related solder bridges. By default the LPUART1 communication between the target STM32 and the ST-LINK is enabled, to support the Virtual COM port (SB130 and SB131 ON). Refer to

Table 8.

name

PG7 LPUART1 TX SB131 ON and SB195 OFF SB131 OFF and SB95 ON

PG8 LPUART1 RX SB130 ON and SB193 OFF SB130 OFF and SB193 ON

Function

5.12 USB FS OTG

The STM32 Nucleo-144 board supports the USB OTG as host or as device-full-speed communication through a USB Micro-AB connector (CN14) and USB power switch (U12) connected to V

Warning: The USB Micro-AB connector (CN14) cannot power a Nucleo-

BUS

Table 8. LPUART1 pin configuration

Virtual COM port (default

configuration)

ST morpho connection

144 board. To avoid damaging the STM32, it is mandatory to power the board before connecting a USB cable on CN14. Otherwise there is a risk of current injection on STM32 I/Os.

UM2179 Rev 8 27/55

Page 28

Hardware layout and configuration UM2179

A green LED LD8 lits up in one of these cases:

• Power switch (U12) is ON and STM32 Nucleo-144 board works as a USB host

• V

is powered by another USB host when the STM32 Nucleo-144 board works as a

BUS

USB device.

The red LED LD7 lits up if overcurrent occurs when +5 V is enabled on V

in USB host

BUS

mode.

Note:1 It is recommended to power the Nucleo-144 board with an external power supply when

using the USB OTG or the host function.

Note:2 JP4 must be closed when using the USB OTG FS.

Note:3 Limitation: when the cable is not connected, PA9 (V

) is not floating, because internal pull

BUS

up of PA12 (D+) impacts PA9 through ESD protection part USBLC6-2SC6 (U13).

For pin configuration refer to Tab le 9.

name

PA8 USB SOF - - Test point TP1

PA9 USB V

PA10 USB ID SB134 ON SB134 OFF -

PA11 USB DM SB142 ON SB142 OFF -

PA12 USB DP SB143 ON SB143 OFF -

PG6 USB GPIO OUT

Function

BUS

Table 9. USB pin configuration

Configuration

using USB

when

connector

SB135 ON SB135 OFF -

OTG:SB201 OFF,

SB200 ON

Configuration

when using ST

morpho

OTG:SB200 OFF

connector

OTG:USB power switch

Remark

control

PG5 USB GPIO IN

JP4 ON, SB199

SB198 ON

OFF

5.13 Solder bridges and jumpers

SBxx are located on top layer and SB1xx-SB2xx on bottom layer of the STM32 Nucleo-144 board. The configuration of the solder bridges and jumpers is showed in

Bridge/jumper State

SB5 (+3V3_PER)

SB6 (3.3 V)

28/55 UM2179 Rev 8

Table 10. Configuration of the solder bridges and jumpers

(1)

ON Peripheral power +3V3_PER is connected to +3.3 V.

OFF Peripheral power +3V3_PER is not connected.

OFF Output of voltage regulator LD39050PU33R is not connected.

Output of voltage regulator LD39050PU33R is connected to 3.3 V.

JP4 OFF USB overcurrent alarm

Table 10.

Description

Page 29

UM2179 Hardware layout and configuration

Table 10. Configuration of the solder bridges and jumpers (continued)

OFF

(1)

Description

PG7 and PG8 on STM32 are connected to ST morpho connectors CN12. If these pins are used on ST morpho connectors, SB130 and SB131 should be OFF.

PG7 and PG8 on STM32 are disconnected to ST morpho connectors CN12.

PA2 and PA3 on ST-LINK STM32F103CBT6 are connected to PG7 and PG8 to enable the Virtual COM port. Thus PG7 and PG8 on ST morpho connectors cannot be used.

PA2 and PA3 on ST-LINK STM32F103CBT6 are disconnected to PG7 and PG8 on STM32.

Bridge/jumper State

SB195, SB193 (GPIO)

SB131, SB130

(ST-LINK-USART)

SB152 (V

DDA

)

SB100,102,104,106

(DEFAULT)

SB101,103,105,107

(RESERVED)

SB141 (SWO)

SB110, SB111,SB112

(IOREF)

SB119 (V

REF+

)

SB137 (SDMMC_D0),

SB136 (SDMMC_D1)

SB124, SB123

(LD1-LED)

ON V

OFF V

on STM32 MCU is connected to VDD.

DDA

on STM32 MCU is disconnected to VDD.

DDA

ON Reserved, do not modify.

OFF Reserved, do not modify.

SWO signal of the STM32 (PB3) is connected to ST-LINK SWO input.

OFF SWO signal of STM32 is not connected.

OFF, OF F,

ON, OFF,

OFF

OFF, ON,

OFF

IOREF is connected to V

IOREF is connected to +3.3 V.

IOREF is connected to +3V3_PER.

Pin 6 of CN7 and Pin 7 of CN12 are disconnected to V STM32.

Pin 6 of CN7 and Pin 7 of CN12 are connected to V STM32.

DD_MCU

ON These pins are connected to ST morpho connector CN12.

OFF

These pins are disconnected from ST morpho connector CN12 to avoid stub of SDMMC data signals on PCB.

ON, OFF Green user LED LD1 is connected to PC7.

OFF,ON

Green user LED LD1 is connected to D13 of ARDUINO (PA5).

OFF, OFF Green user LED LD1 is not connected.

REF+

signal

SB172 (Legacy)

SB173 (SMPS) (LD2-

LED)

ON,ON Forbidden.

ON Blue user LED LD2 is connected to PB7.

OFF Blue user LED LD2 is not connected.

UM2179 Rev 8 29/55

Page 30

Hardware layout and configuration UM2179

Table 10. Configuration of the solder bridges and jumpers (continued)

Bridge/jumper State

(1)

Description

SB132 (LD3-LED)

SB145,146 (X2 crystal)

SB147 (PH0), SB156

(PH1) (Main clock)

SB109, SB148 (MCO)

SB12, SB13 (external

8M crystal)

SB154 (V

BAT

)

SB197, SB178

(B1-USER)

ON Red user LED LD3 is connected to PB14.

OFF Red user LED LD3 is not connected.

OFF

ON, ON

PC14, PC15 are not connected to ST morpho connector CN11. (X2 used to generate 32 KHz clock).

PC14, PC15 are connected to ST morpho connector CN11. (R37 and R38 should be removed).

PH0 and PH1 are connected to ST morpho connector CN11. (SB12, SB13 and SB148 must be removed).

PH0 is not connected to ST morpho

OFF, ON

PH1 is connected to ST morpho connector CN11 (MCO is used as main clock for STM32 on PH0).

PH0, PH1 are not connected to ST morpho connector CN11

OFF, O FF

(X3, C37, C38, SB12 and SB13 provide a clock as shown in

Section Appendix A: Electrical schematics. In this case SB148

must be removed).

OFF

MCO of ST-LINK (STM32F103CBT6) is not connected to PH0

STM32.

MCO of ST-LINK (STM32F103CBT6) is connected to PH0 of STM32.

OFF PH0 and PH1 are not connected to external 8 MHz crystal X3.

ON PH0 and PH1 are connected to external 8 MHz crystal X3.

ON V

OFF V

pin of STM32 is connected to VDD.

BAT

pin of STM32 is not connected to VDD.

BAT

ON, OFF B1 push-button is connected to PC13.

OFF, ON

OFF,

OFF

B1 push-button is connected to PA0 (Set SB179 OFF if ST Zio connector is used).

B1 push-button is not connected.

SB179 (PA0)

ON PA0 is connected to ST Zio connector (Pin 29 of CN10).

OFF PA0 is not connected to ST Zio connector (Pin 29 of CN10).

OFF Default setting.

SB151,SB153

ON Forbidden.

SB158, SB167 (A

VDD

SB142 (PA11), SB143

(PA12)

SB149 (V

REF+

)

ON, OFF A

)

OFF, ON A

ON These pins are used as D+ and D- on USB connector CN14.

OFF These pins are used as GPIOs on ST morpho connectors.

ON V

OFF V

on STM32 is connected to VDD.

VDD

on STM32 is connected to VDD_MCU.

VDD

on STM32 is connected to A

REF+

on STM32 is disconnected to A

REF+

30/55 UM2179 Rev 8

VDD

Page 31

UM2179 Hardware layout and configuration

Table 10. Configuration of the solder bridges and jumpers (continued)

Bridge/jumper State

SB144 (QSPI_IO1)

(2)

JP2

(STM_RST)

JP3 (NRST)

(1)

Description

ON These pins are connected to ST morpho connector CN11.

OFF

These pins are disconnected from ST morpho connector CN11 to avoid stub of QSPI_IO1 signals on PCB.

OFF No incidence on ST-LINK STM32F103CBT6 NRST signal.

OFF

ST-LINK STM32F103CBT6 NRST signal is connected to GND (ST-LINK reset to reduce power consumption).

Board RESET signal (NRST) is connected to ST-LINK reset control I/O

(T_NRST).

Board RESET signal (NRST) is not connected to ST-LINK reset control I/O (T_NRST).

ON,

SB122, SB121, SB127 (V

DD_MCU

)

OFF,OFF

OFF, ON,

1. Default SBx state is shown in bold.

2. The jumper JP2 is not mounted on the board by default.

DD_MCU

All the other solder bridges present on the STM32 Nucleo-144 board are used to configure several I/Os and power supply pins for compatibility of features and pinout with the target

is connected to VDD directly (3.3 V fixed).

is connected to output of DC-DC (1.8 V fixed).

STM32 supported.

STM32 Nucleo-144 boards are delivered with the solder bridges configured according to the target STM32 supported.

UM2179 Rev 8 31/55

Page 32

Hardware layout and configuration UM2179

NUCLEO-L496ZG

CN7

CN10

CN8

CN9

1 3 5 7

9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

1 3 5 7

9 11 13 15

2 4 6

8 10 12 14 16

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30 32 34

PC8

PF5

PF3

PD2

PC12

PC11

PC10

PC9

GND

PD3

PD4

PD5

PD6

PD7

PG1

PF9

PF7

PF8

PE3

PE6

PE4

PE2

PE5

D34

D33

D32

GND

D31

D30

D29

D28

GND

D25

D24

D23

D22

D21

D20

D19

D18

D17

D16

D27

D26

GND

AGND

AVDD

PE0

PB0

PA0

GND

PE14

PE12

PB0

PE15

GND

PB4

PA4

PB3

PB5

PB4

PA4

PB12

PB13

PB15

PC6

PB10

PA2

PA1

PC2

PB1

GND

AGND

AVDDD50

D49

D48

D47

D46

D45

D44

D43

GND

D55

D54

D53

D52

D51

D64

D63

D62

D61

D60

D59

D58

D57

D56

Arduino subset of Zio = A0 to A5 and D0 to D15

Zio extension = A6 to A8 and D16 to D72

USB OTG

USB

ST-LINK

D65

D66

D67

GND

D68

D69

D70

D71

D72

VIN

GND

+5V

+3V3

RESET

IOREF

PG0

PD1

PD0

GND

PF0

PF1

PF2

PB6

PB2

VIN

GND

+5V

+3V3

RESET

IOREF

PC5

PC4

PC1

PC3

PC0

PA3

PF12

PD15

PD14

PA7

PA6

PA5

GND

PB9

PB8

PD9

PD8

PF15

PE13

PF14

PE11

PE9

PF13

PB11

PB10

PE15

PE14

PE12

PE10

PE7

PE8

GND

D10

D11

D12

D13

GND

AVDD

D14

D15

D35

D36

D37

D38

D39

D40

GND

D41

D42

5.14 Expansion connectors

For each STM32 Nucleo-144 board the Figure 11, Figure 12 and Figure 13 show the signals connected by default to the ST Zio connectors (CN7, CN8, CN9 and CN10), including the support for ARDUINO

Uno V3.

Figure 11. NUCLEO-L496ZG

32/55 UM2179 Rev 8

Page 33

UM2179 Hardware layout and configuration

NUCLEO-L496ZG-P

CN7

CN10

CN8

CN9

1 3 5 7

9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

1 3 5 7

9 11 13 15

2 4 6

8 10 12 14 16

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30 32 34

PC8

PF5

PF3

PD2

PC12

PC11

PC10

PC9

GND

PD3

PD4

PD5

PD6

PD7

PG1

PF9

PF7

PF8

PE3

PE6

PE4

PE2

PE5

D34

D33

D32

GND

D31

D30

D29

D28

GND

D25

D24

D23

D22

D21

D20

D19

D18

D17

D16

D27

D26

GND

AGND

AVDD

PE0

PB0

PA0

GND

PE14

PE12

PB0

PE15

GND

PB4

PA4

PB3

PB5

PB4

PA4

PB12

PB13

PB15

PC6

PB10

PA2

PA1

PC2

PB1

GND

AGND

AVDDD50

D49

D48

D47

D46

D45

D44

D43

GND

D55

D54

D53

D52

D51

D64

D63

D62

D61

D60

D59

D58

D57

D56

Arduino subset of Zio = A0 to A5 and D0 to D15

Zio extension = A6 to A8 and D16 to D72

USB OTG

USB

ST-LINK

D65

D66

D67

GND

D68

D69

D70

D71

D72

VIN

GND

+5V

+3V3

RESET

IOREF

PG0

PD1

PD0

GND

PF0

PF1

PF2

PB6

PB2

VIN

GND

+5V

+3V3

RESET

IOREF

PC5

PC4

PC1

PC3

PC0

PA3

PF12

PD15

PD14

PA7

PA6

PA5

GND

PB9

PB8

PD9

PD8

PF15

PE13

PF14

PE11

PE9

PF13

PB10

PE15

PE14

PE12

PE10

PE7

PE8

GND

D10

D11

D12

D13

GND

AVDD

D14

D15

D35

D36

D37

D38

D39

D40

GND

D41

D42

Figure 12. NUCLEO-L496ZG-P

UM2179 Rev 8 33/55

Page 34

Hardware layout and configuration UM2179

NUCLEO-L4A6ZG

CN7

CN10

CN8

CN9

1 3 5 7

9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

1 3 5 7

9 11 13 15

2 4 6

8 10 12 14 16

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30 32 34

PC8

PF5

PF3

PD2

PC12

PC11

PC10

PC9

GND

PD3

PD4

PD5

PD6

PD7

PG1

PF9

PF7

PF8

PE3

PE6

PE4

PE2

PE5

D34

D33

D32

GND

D31

D30

D29

D28

GND

D25

D24

D23

D22

D21

D20

D19

D18

D17

D16

D27

D26

GND

AGND

AVDD

PE0

PB0

PA0

GND

PE14

PE12

PB0

PE15

GND

PB4

PA4

PB3

PB5

PB4

PA4

PB12

PB13

PB15

PC6

PB10

PA2

PA1

PC2

PB1

GND

AGND

AVDDD50

D49

D48

D47

D46

D45

D44

D43

GND

D55

D54

D53

D52

D51

D64

D63

D62

D61

D60

D59

D58

D57

D56

Arduino subset of Zio = A0 to A5 and D0 to D15

Zio extension = A6 to A8 and D16 to D72

USB OTG

USB

ST-LINK

D65

D66

D67

GND

D68

D69

D70

D71

D72

VIN

GND

+5V

+3V3

RESET

IOREF

PG0

PD1

PD0

GND

PF0

PF1

PF2

PB6

PB2

VIN

GND

+5V

+3V3

RESET

IOREF

PC5

PC4

PC1

PC3

PC0

PA3

PF12

PD15

PD14

PA7

PA6

PA5

GND

PB9

PB8

PD9

PD8

PF15

PE13

PF14

PE11

PE9

PF13

PB11

PB10

PE15

PE14

PE12

PE10

PE7

PE8

GND

D10

D11

D12

D13

GND

AVDD

D14

D15

D35

D36

D37

D38

D39

D40

GND

D41

D42

Figure 13. NUCLEO-L4A6ZG

34/55 UM2179 Rev 8

Page 35

UM2179 Hardware layout and configuration

NUCLEO-L4R5ZI

CN7

CN10

CN8

CN9

1 3 5 7

9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

1 3 5 7

9 11 13 15

2 4 6

8 10 12 14 16

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30 32 34

PC8

PF5

PF3

PD2

PC12

PC11

PC10

PC9

GND

PD3

PD4

PD5

PD6

PD7

PG1

PF9

PF7

PF8

PE3

PE6

PE4

PE2

PE5

D34

D33

D32

GND

D31

D30

D29

D28

GND

D25

D24

D23

D22

D21

D20

D19

D18

D17

D16

D27

D26

GND

AGND

AVDD

PE0

PB0

PA0

GND

PE14

PE12

PB0

PE15

GND

PB4

PA4

PB3

PB5

PB4

PA4

PB12

PB13

PB15

PC6

PB10

PA2

PA1

PC2

PB1

GND

AGND

AVDDD50

D49

D48

D47

D46

D45

D44

D43

GND

D55

D54

D53

D52

D51

D64

D63

D62

D61

D60

D59

D58

D57

D56

Arduino subset of Zio = A0 to A5 and D0 to D15

Zio extension = A6 to A8 and D16 to D72

USB OTG

USB

ST-LINK

D65

D66

D67

GND

D68

D69

D70

D71

D72

VIN

GND

+5V

+3V3

RESET

IOREF

PG0

PD1

PD0

GND

PF0

PF1

PF2

PB6

PB2

VIN

GND

+5V

+3V3

RESET

IOREF

PC5

PC4

PC1

PC3

PC0

PA3

PF12

PD15

PD14

PA7

PA6

PA5

GND

PB9

PB8

PD9

PD8

PF15

PE13

PF14

PE11

PE9

PF13

PB11

PB10

PE15

PE14

PE12

PE10

PE7

PE8

GND

D10

D11

D12

D13

GND

AVDD

D14

D15

D35

D36

D37

D38

D39

D40

GND

D41

D42

Figure 14. NUCLEO-L4R5ZI

UM2179 Rev 8 35/55

Page 36

Hardware layout and configuration UM2179

NUCLEO-L4R5ZI-P

CN7

CN10

CN8

CN9

1 3 5 7

9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

1 3 5 7

9 11 13 15

2 4 6

8 10 12 14 16

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30

1 3 5 7

9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6

8 10 12 14 16 18 20 22 24 26 28 30 32 34

PC8

PF5

PF3

PD2

PC12

PC11

PC10

PC9

GND

PD3

PD4

PD5

PD6

PD7

PG1

PF9

PF7

PF8

PE3

PE6

PE4

PE2

PE5

D34

D33

D32

GND

D31

D30

D29

D28

GND

D25

D24

D23

D22

D21

D20

D19

D18

D17

D16

D27

D26

GND

AGND

AVDD

PE0

PB0

PA0

GND

PE14

PE12

PB0

PE15

GND

PB4

PA4

PB3

PB5

PB4

PA4

PB12

PB13

PB15

PC6

PB10

PA2

PA1

PC2

PB1

GND

AGND

AVDDD50

D49

D48

D47

D46

D45

D44

D43

GND

D55

D54

D53

D52

D51

D64

D63

D62

D61

D60

D59

D58

D57

D56

Arduino subset of Zio = A0 to A5 and D0 to D15

Zio extension = A6 to A8 and D16 to D72

USB OTG

USB

ST-LINK

D65

D66

D67

GND

D68

D69

D70

D71

D72

VIN

GND

+5V

+3V3

RESET

IOREF

PG0

PD1

PD0

GND

PF0

PF1

PF2

PB6

PB2

VIN

GND

+5V

+3V3

RESET

IOREF

PC5

PC4

PC1

PC3

PC0

PA3

PF12

PD15

PD14

PA7

PA6

PA5

GND

PB9

PB8

PD9

PD8

PF15

PE13

PF14

PE11

PE9

PF13

PB10

PE15

PE14

PE12

PE10

PE7

PE8

GND

D10

D11

D12

D13

GND

AVDD

D14

D15

D35

D36

D37

D38

D39

D40

GND

D41

D42

Figure 15. NUCLEO-L4R5ZI-P

36/55 UM2179 Rev 8

Page 37

UM2179 Hardware layout and configuration

5.15 ST Zio connectors

The connectors CN7, CN8, CN9 and CN10 are female on top side and male on bottom side of the STM32 Nucleo-144 board. designed for ARDUINO

Caution: The I/Os of the STM32 microcontroller are 3.3 V compatible, while ARDUINO® Uno V3 is

5 V compatible.

Tab le 11 shows the pin assignments for the STM32 on the ST Zio connector.

They include support for ARDUINO® Uno V3. Most shields

Uno V3 can fit to the STM32 Nucleo-144 board.

UM2179 Rev 8 37/55

Page 38

Hardware layout and configuration UM2179

Table 11. NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI,

NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments

Connector Pin Pin name Signal name STM32 pin Function Remark

Left connectors

CN8

1NC NC

3 IOREF IOREF 3.3 V Ref

5 RESET RESET NRST RESET

7 +3.3 V +3.3 V

9 +5 V +5 V 5 V output

11 GND GND

13 GND GND

15 V

2 D43 SDMMC_D0 PC8

4D44

SDMMC_D1/

I2S_A_CKIN

PC9

6 D45 SDMMC_D2 PC10

8 D46 SDMMC_D3 PC11

10 D47 SDMMC_CK PC12

12 D48 SDMMC_CMD PD2

3.3 V

input/output

ground

Power input

SDMMC/I2S_A

Arduino support

CN9

14 D49 I/O PF3

I/O

16 D50 I/O PF5

1 A0 ADC PA3 ADC12_IN8

3 A1 ADC PC0 ADC123_IN1

5 A2 ADC PC3 ADC123_IN4

7 A3 ADC PC1 ADC123_IN2

9A4

11 A5

(1)

ADC PC4 ADC12_IN13

ADC PC5 ADC12_IN14

13 D72 COMP1_INP PB2 COMP

15 D71 COMP2_INP

PB6

17 D70 I2C_B_SMBA PF2

I2C_2

19 D69 I2C_B_SCL PF1

21 D68 I2C_B_SDA PF0

23 GND GND - ground

25 D67 CAN_RX PD0

CAN_1

27 D66 CAN_TX PD1

29 D65 I/O PG0 I/O

2 D51 USART_B_SCLK PD7 USART_2

Arduino

support

38/55 UM2179 Rev 8

Page 39

UM2179 Hardware layout and configuration

Table 11. NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI,

NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments (continued)

Connector Pin Pin name Signal name STM32 pin Function Remark

4 D52 USART_B_RX PD6

CN9

CN7

6 D53 USART_B_TX PD5

USART_2

8 D54 USART_B_RTS PD4

10 D55 USART_B_CTS PD3

12 GND GND - ground

14 D56 SAI_A_MCLK

PE2

16 D57 SAI_A_FS PE4

SAI_1_A

18 D58 SAI_A_SCK PE5

20 D59 SAI_A_SD PE6

22 D60 SAI_B_SD PE3

24 D61 SAI_B_SCK PF8

SAI_1_B

26 D62 SAI_B_MCLK PF7

28 D63 SAI_B_FS PF9

30 D64 I/O PG1 I/O

Right connectors

1 D16 I2S_A_MCK PC6

3 D17 I2S_A_SD PB15

SAI_2_A

5 D18 I2S_A_CK PB13

7 D19 I2S_A_WS PB12

9 D20 I2S_B_WS PA4

11 D21 I2S_B_MCK PB4

13 D22

15 D23

I2S_B_SD/

SPI_B_MOSI

I2S_B_CK/

SPI_B_SCK

PB5

PB3

SAI_1_B/

(2)

SPI3

17 D24 SPI_B_NSS PA4

19 D25 SPI_B_MISO PB4

2 D15 I2C_A_SCL PB8 I2C1_SCL

4 D14 I2C_A_SDA PB9 I2C1_SDA

6 AREF AREF

VREF+

(3)

8 GND GND ground

10 D13 SPI_A_SCK PA5 SPI1_SCK

12 D12 SPI_A_MISO PA6 SPI1_MISO

14 D11

SPI_A_MOSI/

TIM_E_PWM1

PA7

SPI1_MOSI/

TIM17_CH1

UM2179 Rev 8 39/55

Arduino support

Page 40

Hardware layout and configuration UM2179

Table 11. NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI,

NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments (continued)

Connector Pin Pin name Signal name STM32 pin Function Remark

CN7

CN10

16 D10

SPI_A_CS/

TIM_B_PWM3

PD14

SPI1_CS/

TIM4_CH3

20 D8 I/O PF12 -

1AVDD AVDD

3 AGND AGND Analog ground

Analog VDD

5 GND GND ground

7 A6 ADC_A_IN PB1 ADC12_IN16

9 A7 ADC_B_IN PC2 ADC123_IN3

11 A8 ADC_C_IN PA1 ADC12_IN6

13 D26 QSPI_CS PA2

15 D27 QSPI_CLK PB10

(4)

QSPI_BK1

QSPI_CLK

17 GND GND - ground

PE14

(4)

QSPI_BK1

19 D28 QSPI_BK1_IO3 PE15

21 D29 QSPI_BK1_IO1 PB0

23 D30 QSPI_BK1_IO0 PE12

25 D31 QSPI_BK1_IO2

27 GND GND - ground

29 D32 TIMER_C_PWM1 PA0

31 D33 TIMER_D_PWM1 PB0

(4)

TIM2_CH1

TIM3_CH3

33 D34 TIMER_B_ETR PE0 TIM4_ETR

Arduino support18 D9 TIMER_B_PWM2 PD15 TIM4_CH4

2D7 I/O PF13 -

4 D6 TIMER_A_PWM1 PE9 TIM1_CH1

6 D5 TIMER_A_PWM2 PE11 TIM1_CH2

8D4 I/O PF14 -

10 D3 TIMER_A_PWM3 PE13 TIM1_CH3

12 D2 I/O PF15 -

14 D1 USART_A_TX PD8

16 D0 USART_A_RX PD9

18 D42 TIMER_A_PWM1N PE8 TIM1_CH1N

20 D41 TIMER_A_ETR PE7 TIM1_ETR

22 GND GND - ground

24 D40 TIMER_A_PWM2N PE10 TIM1_CH2N

26 D39 TIMER_A_PWM3N PE12

40/55 UM2179 Rev 8

Arduino support

USART3

(4)

TIM1_CH3N

Page 41

UM2179 Hardware layout and configuration

Table 11. NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI,

NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments (continued)

Connector Pin Pin name Signal name STM32 pin Function Remark

28 D38 I/O PE14

30 D37 TIMER_A_BKIN1 PE15

CN10

32 D36 TIMER_C_PWM2 PB10

34 D35 TIMER_C_PWM3 PB11

1. To be compatible with the previous versions of the ARDUINO® Uno V3 board, A4/A5 do not support I2C.

2. I2S_B group has the same port as SAI_B group, but they have a different pin map.

3. V

4. QSPI signals (PA2, PB10, PE15, PB0, PE12 and PE14) are shared with timer signals on CN10.

5. PB11 is not available on ‘-P’ suffixed boards.

is not connected to CN7 by default.

REF+

(4)

(5)

I/O

TIM1_BKIN1

TIM2_CH3

TIM2_CH4

5.16 ST morpho connector

The ST morpho connector consists in male pin header footprints CN11 and CN12 (not soldered by default). They can be used to connect the STM32 Nucleo-144 board to an extension board or a prototype/wrapping board placed on top of the STM32 Nucleo-144 board. All signals and power pins of the STM32 are available on the ST morpho connector. This connector can also be probed by an oscilloscope, logical analyzer or voltmeter.

Tab le 12 shows the pin assignments for the STM32 on the ST morpho connector.

CN11 odd pins CN11 even pins CN12 odd pins CN12 even pins

Pin Pin name Pin Pin name Pin Pin name Pin Pin name

1PC102PC111PC92PC8

3 PC12 4 PD2 3 PB8 4 PC6

9PF610 - 9GND10PD8

11 PF7 12 IOREF 11 PA5 12 PA12

13 PA13

15 PA14

17 PA15 18 +5 V 17 PB6 18 PB11

19 GND 20 GND 19 PC7 20 GND

Table 12. ST morpho connector pin assignments

PH3-

BOOT0

(1)

(4)

6 E5V 5 PB9 6 PC5

8GND7V

14 RESET 13 PA6 14 PA11

16 +3.3 V 15 PA7 16 PB12

(2)

REF+

U5V

(3)

21 PB7 22 GND 21 PA9 22 PB2

23 PC13 24 V

23 PA8 24 PB1

25 PC14 26 - 25 PB10 26 PB15

27 PC15 28 PA0 27 PB4 28 PB14

UM2179 Rev 8 41/55

Page 42

Hardware layout and configuration UM2179

Table 12. ST morpho connector pin assignments (continued)

CN11 odd pins CN11 even pins CN12 odd pins CN12 even pins

Pin Pin name Pin Pin name Pin Pin name Pin Pin name

29 PH0 30 PA1 29 PB5 30 PB13

31 PH1 32 PA4 31 PB3 32 AGND

33 V

BAT

35 PC2 36 PC1 35 PA2 36 PF5

37 PC3 38 PC0 37 PA3 38 PF4

39 PD4 40 PD3 39 GND 40 PE8

41 PD5 42 PG2 41 PD13 42 PF10

43 PD6 44 PG3 43 PD12 44 PE7

45 PD7 46 PE2 45 PD11 46 PD14

47 PE3 48 PE4 47 PE10 48 PD15

49 GND 50 PE5 49 PE12 50 PF14

51 PF1 52 PF2 51 PE14 52 PE9

34 PB0 33 PA10 34 PC4

53 PF0 54 PF8 53 PE15 54 GND

55 PD1 56 PF9 55 PE13 56 PE11

57 PD0 58 PG1 57 PF13 58 PF3

59 PG0 60 GND 59 PF12 60 PF15

61 PE1 62 PE6 61 PG14 62 PF11

63 PG9 64 PG15

65 PG12 66 PG10 65 PD10 66 PG8

67 - 68PG1367 PG7 68 PG5

69 PD9 70 PG11 69 PG4 70 PG6

1. Default state of BOOT0 is 0. It can be set to 1 when a jumper is plugged on the pins 5-7 of CN11.

2. V

3. U5V is the +5V power signal, coming from the ST-LINK/V2-1 USB connector. It rises before the +5V signal

4. PA13 and PA14 are shared with SWD signals connected to ST-LINK/V2-1. If ST-LINK part is not cut, it is

5. PB11 and PG15 are not available on the ‘-P’ suffixed boards.

is not connected to CN12 by default.

REF+

of the board.

not recommended to use them as I/O pins.

5.17 Bootloader limitation

(5)

63 GND 64 PE0

5.17.1 Bootloader operation

Boot from system Flash memory runs bootloader code stored in the system Flash memory protected against writing and erasing. This allows in-system programming (ISP) with flashing of the STM32 user Flash memory. It also allows writing data into the RAM. The data is written via the USART, SPI, I

42/55 UM2179 Rev 8

C, USB or CAN communication interface.

Page 43

UM2179 Hardware layout and configuration

5.17.2 Bootloader identification

The bootloader version is identified by reading the bootloader ID at address 0x1FFF 6FFE:

• the bootloader ID is 0x91 for bootloader version V9.1.

• the bootloader ID is 0x92 for bootloader version V9.2.

5.17.3 Bootloader limitation

The limitation existing in bootloader V9.1 causes user Flash memory data to get randomly corrupted when written via the bootloader SPI interface.

As a result, during bootloader SPI Write Flash operation, some random 64-bits (2 doublewords) may be left blank at 0xFF.

5.17.4 Affected parts

The STM32L496ZGT6, STM32L496ZGT6P, and STM32L4R5ZIT6 parts respectively soldered on the NUCLEO-L496ZG, NUCLEO-L496ZG-P, and NUCLEO-L4R5ZI main boards are marked with a date code corresponding to their manufacturing dates.

The STM32L496ZGT6, STM32L496ZGT6P, and STM32L4R5ZIT6 parts with a date code prior or equal to week 37 of 2017 are fitted with bootloader V9.1. They are affected by the limitation described in

Section 5.17.5.

Section 5.17.3 and require one of the workarounds proposed in

The parts with a date code equal to week 38 of 2017 or later contain bootloader V9.2. They are not affected by the limitation.

To locate the visual date code information on the STM32L496ZGT6, STM32L496ZGT6P, or STM32L4R5ZIT6 package, refer to the Package Information section in the data sheet available at www.st.com. The date code related portion of the package marking is in the Y

WW format, where Y is the last digit of the year and WW is the week number. For

example, a part manufactured in week 38 of 2017 bears the 7

5.17.5 Workarounds

Three workarounds are proposed to overcome the limitation existing with bootloader V9.1.

Workaround 1

Add a delay between sending a Write command and its ACK request. The delay duration must be the duration of the 256-byte Flash-write time.

Workaround 2

Read back after each write operation (256 bytes or end of user code flashing) and, in case of error, perform the write operation again.

Workaround 3

Using the bootloader, load a patch code in RAM to write in Flash memory through the same Write Memory write protocol as the bootloader This patch is provided by STMicroelectronics. The patch code is available for download from the www.st.com website with a readme.txt file containing the instructions of use.

38 date code.

UM2179 Rev 8 43/55

Page 44

Electrical schematics UM2179

Appendix A Electrical schematics

This section provides the design schematics for the STM32 Nucleo-144 board:

• Top and Power (see Figure 16)

• MCU (see Figure 17)

• ST-LINK/V2-1 (see Figure 18)

• USB (see Figure 19)

• Extension connector (see Figure 20)

• SMPS power supply (see Figure 21)

44/55 UM2179 Rev 8

Page 45

Figure 16. Top and power

TOP & POWER

MB1312 A-01

12/8/2016

Title:

Size: Reference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXProject:

+3V3

C19

1uF_X5R_0603 C26 100nF

C20 100nF

VIN

+5V

VDD

JP5

R28 1K

C18 10uF(25V)

C17 10uF

Vin3Vout

Tab

U5 LD1117S50TR

GND

U6 LD39050PU33R

Note1: Text in italic placed on a wire does not correspond to net name. It just

C27

1uF_X5R_0603

E5V

Power Switch to supply +5V from STLINK USB

C16

4.7uF

GND

SET

OUT

FAULT

ST890CDR

R26 10K

R27 2K7

C11 100nF

1 2 LD5

Red

R22 1K

U5V

SB6 Closed

VIN_5V

SB5 Closed

+3V3_PER

LD6 Green

NRST

MCO

STLK_TX

STLK_RX

PA[0..15] PB[0..15] PC[0..15]

TCK TMS SWO

PH3-BOOT0

PD[0..15] PE[0..15] PF[0..15] PG[0..15] PH[0..1]

USB_DM

USB_DP

USB_GPIO_OUT

USB_GPIO_IN

USB_ID

USB_VBUS

U_STM32L_144 STM32L_144.SchDoc

PA[0..15] PB[0..15] PC[0..15]

NRST

PH3-BOOT0

PD[0..15] PE[0..15]

PF[0..15]

PG[0..15]

PH[0..1]

U_Connectors Connectors.SchDoc

TMS

TCK

MCO

NRST

STLK_RX STLK_TX

SWO

PWR_ENn

U_ST_LINK_V2-1 ST_LINK_V2-1.SCHDOC

USB_PowerSwitchOn USB_OverCurrent

USB_DM

USB_DP

USB_ID

USB_VBUS

USB_Disconnect

VBUS_DET

U_USB USB.SchDoc

PG[0..15]

U_SMPS powersupply SMPS powersupply.SchDoc

6 5 4 3 2 1

8 7

JP6

Header 4X2

U5V

CuttableLineonPCB

UM2179 Electrical schematics

UM2179 Rev 8 45/55

helps to identify rapidly Arduino's signal related to this wire.

Page 46

46/55 UM2179 Rev 8

MCU

MB1312 A-01

12/8/2016

Title:

Size: Reference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXProject:

C38 4.3pF [N/A]

C37 4.3pF [N/A]

C36

2.7pF

C35

2.7pF

R400R39

C41

100nF

R38 10K

PA4 PA5 PA6 PA7

PA11 PA12

PA0 PA1

PA15

PA3

PA13 PA14

PA2

PA8

NRST

PB5

PB6

PB7

PB14 PB15

PB10

PB8

PB9

PB1 PB2

PB3

PB0

PB4

PB11

PB12 PB13

PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PC8 PC9 PC10 PC11 PC12

PC13 PC14 PC15

NRST

MCO

STLK_TX

STLK_RX

BEAD

AVDD

PA[0..15]

PB[0..15]

PC[0..15]

TCK

TMS

SWO

PH0 PH1

AVDD

C58 100nF

AGND

C60 1uF_X5R_0603

VBAT

PH3-BOOT0

AGND

VDD

AGND

C29 100nF

C61 100nF

C49 100nF

C33 100nF

C34 100nF

PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 PD8 PD9 PD10 PD11 PD12 PD13 PD14 PD15

PE0

PE1

PE2 PE3 PE4 PE5 PE6

PE14 PE15

PE9

PE8

PE11

PE10

PE12 PE13

PE7

PF0 PF1 PF2 PF3 PF4 PF5

PF14 PF15

PF9

PF8

PF11

PF10

PF12 PF13

PF6 PF7

PG0 PG1 PG2 PG3 PG4 PG5

PG14

PG9

PG8

PG11

PG10

PG12 PG13

PG6 PG7

PG15

PD[0..15]

PE[0..15]

PF[0..15]

PG[0..15]

PH[0..1]

SB152

Closed

SB154 Closed

SB197 Closed

SB166 Closed

NX3215SA-32. 768KHZ-EX S00A-MU00525

C31 100nF

C50 100nF

C51 100nF

C53 100nF

C30 100nF

C32 100nF

C28 100nF

USB_DM USB_DP

SB142 Closed SB143 Closed

USB_GPIO_OUT

USB_GPIO_IN

R42 220K

C40 [N/A]

R44

100

R43

330

JP4

PA9 PA10

R54,SB134 & SB135 removed for U SB device only

USB_ID

USB_VBUS

R54 10K

SB134

LPUART1_TX LPUART1_R X

TP1 USB_SOF

SB130 Closed

SB131 Closed

4 3

USER (Blue)

TD-0341[RESET/Black]

1 2

NX3225GD-8. 000M-EXS00A -CG04874[N/A]

1 2LD3

Red

R30

680

R29

SB132 Closed

SB12 Open

SB13 Open

C54

4.7uF_X5R_0603

SB135

SB178 Open

Usr_But

1 2

LD2 Blue

SB148 Open

VDD_1V2 VDD_1V2

SB139 SB15

C39 and C 55, non m ounted 1nF capacitances on L egay (when SB15 and SB 139 are open)

SB185 SB187 PE0

SB186

SB181

SB172 SB171 PH3-BOOT0

PH3-BOOT0

SB174 SB173

SB176 SB175

SB163 SB165

SB162 SB164

SB138

VREF+

SB149

Closed

1uF

C59

C57 100nF

AGND

1uF

C56

VREF+VDD

SB190 SB189 SB14

SB183 SB184 PB8

SB160 SB161 PB3

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PB0

PB1

PB2

PB10

PB11/SMPSVDD12

PB12

PB13

PB14

PB15

PA8

100

PA9

101

PA10

102

PA11

103

PA12

104

PA13

105

PA14

109

PA15

110

PB3/PB4

133

PB4/PB5

134

PB5/PB6

135

PB6/PB7

136

PB7/PH3-BOOT0

137

PB8/PB9

139

PB9/PE0

140

PC13

PC14-OSC 32_IN

PC15-OSC 32_OUT

PC0

PC1

PC2

PC3

PC4

PC5

PC6

PC7

PC8

PC9

PC10

111

PC11

112

PC12

113

U11A

STM32L_L QFP144

PE2

PE3

PE4

PE5

PE6

PE7

PE8

PE9

PE10

PE11

PE12

PE13

PE14

PE15

PD8

PD9

PD10

PD11

PD12

PD13

PD14

PD15

PD0

114

PD1

115

PD2

116

PD3

117

PD4

118

PD5

119

PD6

122

PD7

123

PE0/PE1

141

PE1/SMPSVDD12

142

PF2

PF3

PF4

PF5

PF6

PF7

PF8

PF9

PF10

PF11

PF12

PF13

PF14

PF15

PF0

PF1

PG2

PG3

PG4

PG5

PG6

PG7

PG8

PG9

124

PG10

125

PG11

126

PG12

127

PG13

128

PG14

129

PG15/PB3

132

PG0

PG1

U11B

STM32L_L QFP144

VSS_5

VDD_5

VSSA/VREF-

VREF+

VDD_10

121

VDDIO_2

VDD_6

VDD_7

VDD_8

VDDIO_2

131

VSS_10

120

VSSIO_1

VSS_6

VSS_7

VSS_8

VSSIO_2

130

VDDUSB

106

VSS_3

143

PH0-OSC_IN

PH1-OSC_OUT

NRST

PH3-BOO T0/PB8

138

VDDA

VDD_4

VDD_1

VDD_2

108

VDD_3

144

VBAT

VREF-/VSSA

VSS_2

107

VSS_4

VSS_1

U11C

STM32L_L QFP144

VDD_MCU

SB158 Closed SB167 Open

VDD_MCU VDD_MCU VDD_MCU

C55 1nF C39 1nF

C52

4.7uF_X5R_0603

VDD

VDD_MCU

Figure 17. MCU

Electrical schematics UM2179

Page 47

Figure 18. ST-LINK/V2-1

STLINK/V2-1

MB1312 A-01

12/8/2016

Title:

Size: Reference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXProject:

STLINK_USB_DM

STLINK_USB_DP

STM_RST

T_JTCK

T_JTDO

T_JTDI

T_JTMS

STM_JTMS

STM_JTCK

OSC_IN OSC_OUT

T_NRST

AIN_1

USB ST-LINK

U5V

COM

PWR

Jumpers ON --> NUCLEO Selected Jumpers OFF --> ST-LINK Selected

Board Ident: PC13=0

T_JTCK

T_JTMS

SWD

123

CN4

STM_JTMS

STM_JTCK

SWCLK

SWDIO

SWD

RESERVED

DEFAULT

T_SWDIO_IN

LED_STLINK

TMS

TCK

TCK/SWCLK

TMS/SWDIO

MCO

T_JRST

AIN_1

T_NRST

T_SWO

NRST

T_NRST

BAT60JFILM

CN6

TX RX

STLK_RX

STLK_TX

STLINK_USB_DM STLINK_USB_DP

T_SWO

SWO

SWO_MCU

Red

_Green

2 1

3 4

LD4

LD_BICOLOR_CMS

R9 1K5

R10 100K

R18

100

R12

100

R13

R1 100[N/A]

R14 22

R15 22

R19 22

R20 22

R21 100

R25

100[N/A]

10K

R4 10K[N/A]

R5 100K

100K

R3 10K

R23 4K7

R24 4K7

C1 100nF

C12 100nF

C13 100nFC3100nF

C7 20pF[N/A]

C5 10pF

C6 10pF

100nF

1 2 3 4 5 6

CN5

Header 6X1

U5V

USB_RENUMn

PWR_ENn

2K7R64K7

+3V3_ST_LINK

JP1

+3V3_ST_LINK

PWR_EXT

+3V3_ST_LINK

BAT60JFILM

C14

1uF_X5R_0603

C15 10nF_X7R_0603

C9 1uF_X5R_0603

C10 100nF

C8 100nF

+3V3_ST_LINK

R11 10K

R17 36K

U5V

R16 100

+3V3_ST_LINK

CN3

Wired on Solder Side

CN2

E5V

VBAT

PA7

PC13

PA12

PC14

PB0

PC15

JTMS/SWDIO

OSCIN

PB1

OSCOUT

VSS_2

NRST

PB2/BOOT1

VSSA

VDD_2

VDDA

PB10

PA0

JTCK/SWCLK

PA1

PB11

PA2

PA15/JTDI

PA3

VSS_1

PA4

PB3/JTDO

PA5

VDD_1

PA6

PB4/JNTRST

PB12

PB5

PB13

PB6

PB14

PB7

PB15

BOOT0

PA8

PB8

PA9

PB9

PA10

VSS_3

PA11

VDD_3

U2 STM32F103CBT6

BAT60JFILM

SB100

Closed

SB102

Closed

SB104

Closed

SB106

Closed

SB101

Open

SB103

Open

SB105

Open

SB107

Open

SB141 Closed

+5V

1 2

NX3225GD-8.000M-EXS00A-CG04874

I/O1

GND

I/O23I/O2

Vbus

I/O1

USBLC6-2SC6

C4 100nF

U5V

Diff Pair 90ohm

VBUS

GND

Shield

USB_Micro-B receptacle

Shield

EXP

CN1

1050170001

VIN_5V

BAT60JFILM

T1 9013

+3V3_PER

SB109 Open

VccA

GND4DIR

VccB

U14

SN74LVC2T45DCUT

100nF

C44

100nF

C43

+3V3_ST_LINK

T_JTMST_SWDIO_IN

T_SWO

SWO_MCU

SB108 Open

JP3

VDD_MCU

JP2

GND

BYPASS

Vin Vout

U3 LDK120M33R

UM2179 Electrical schematics

UM2179 Rev 8 47/55

Page 48

48/55 UM2179 Rev 8

USB

MB1312 A-01

12/8/2016

Title:

Size: Reference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXProject:

+5V

USB_PowerSwitchOn

USB_OverCurrent

LD7 Red

R45 620

USB_DM USB_DP USB_ID

C42

4.7uF

GND

OUT

FAULT

U12

STMPS2151STR

R41 330

LD8 Green

R48 22K

R52 10K

R51 47K

R49

47K

T2 9013

USB_VBUS

PA10

PA9

PA12

PA11

PG6

PG5

Diff Pair 90ohm

+3V3_PER

Remove for USB device only

USB_Disconnect

R50 1K5

PG6

Solder only for USB device only

VBUS_DET

R46 430K

R47 620K

SB200

SB198

SB199

SB201

ESDALC6V1-1U2

I/O1

GND

I/O23I/O2

Vbus

I/O1

U13

USBLC6-2SC6

USB Micro-AB receptacle:475891001

VBUS

GND

Shield

EXP

CN14

Micro-AB or Micro-B

USB Micro-B receptacle:1050170001 used for device only

PG5

Figure 19. USB

Electrical schematics UM2179

Page 49

Extension connectors

MB1312 A-01

12/8/2016

Title:

Size: R eference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXProject:

Extension connectors

A0 A1 A2 A3 A4 A5

VIN

PA[0..15]

PB[0..15]

PC[0..15]

AGND

NRST

AVDD

PH3-BOOT0

SB151/SB 153 Close only for I2C on A4/A5

LD1 Green

R31

510

PD[0..15]

PE[0..15]

PF[0..15]

PG[0..15]

SB153 Open

SB151 Open

PH[0..1]

R36 200K

2 5

TSV631AILT

R37

10K

SDMMC_CK SDMMC_CMD

SDMMC_D0 SDMMC _D1/I2S_A_CK IN SDMMC_D2 SDMMC_D3

TIMER_A_PWM1N

TIMER_A_PWM2N TIMER_A_PWM3N

TIMER_A_BKIN1

TIMER_A_BKIN2

TIMER_A_ETR

SAI_A_S D

SAI_A_S CK

SAI_A_FS

SAI_A_MCLK

SAI_B_S D SAI_B_S CK

SAI_B_FS

SAI_B_MCLK

TIMER_D_PWM1 TI MER_C_PW M2 TIMER_B_ETR

TIMER_C_PWM1

TIMER_C _PWM3

I2S_A_SD I2S_A_CK I2S_A_WS

I2S_A_MCK

I2S_B_SD/SPI_B_MOSI I2S_B_CK/SPI_B_SCK

I2S_B_WS I2S_B_MCK

QSPI_C LK

QSPI_CS

QSPI_BK1_IO0 QSPI_BK1_IO2

QSPI_BK1_IO1

QSPI_BK1_IO3

ADC_A_IN ADC_B_IN ADC_C_IN

I2C_B_SCL I2C_B_SDA

I2C_B_SMBA

SPI_B_MISO

SPI_B_NSS

USART_B_TX

USART_B_RX

USART_B_SCLK

USART_B_CTS

USART_B_RTS

CAN_TX

CAN_RX PA0

PA3

PB5

PB15

PB10

PB1

PB3

PB11

PB12

PC0

PC2PC3

PC6

PC8 PC9 PC10 PC11 PC12

PD0 PD1

PD2

PD3

PD4

PD5

PD6

PD7

PD15

PE0

PE2

PE3

PE4 PE5 PE6

PE14 PE15

PE8

PE10

PE12

PE7

PF0

PF1

PF2

PF9

PF8 PF7

PG0 PG1

PF12

NRST

+5V

+3V3

PF14

PF15

PF13

D4 D3

D10

D14

D15

D13 D12 D11

PA5 PA6

PB8 PB9

COMP1_IN P

USART_A_TX USART_A_RX

TIMER_B_PWM2

SPI_A_CS/TIM_B_PWM3

SPI_A_MOSI/TIM_E_PWM1

SPI_A_SCK SPI_A_MISO

I2C_A_SCL I2C_A_SDA

PA7 PD14

IO IO

IOIO

PC1 PC4 PC5

PE9 PE11

PE13

PB0

PB2 PB6

PB13

PB8

PB9

1 3 5 7 9 11 13 15

2 4 6

8 10 12 14 16

CN8

Header 8X2_Fem ale

1 3 5 7 9 11 13 15 17 19

2 4 6

8 10 12 14 16 18 20

CN7

Header 10X2_Fem ale

PA1

2 4 6

8 10 12

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

1 3 5 7 9 11

CN9

Header 15X2_Fem ale

1 3 5 7 9 11 13 15

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

2 4 6

8 10 12 14 16

CN10

Header 17X2_Fem ale

SB124 Closed

PA0

PA4

PB0

PA1

PA15

PA13 PA14

PC2 PC3

PB7

PC10 PC11 PC12

PC13 PC14 PC15

PF6

PF7

NRST

PD2

PH0 PH1

VDD

VBAT

E5V

SB156 Closed

SB146 Open

SB145 Open

PC1 PC0

+3V3

VIN

+5V

PE0

PE1

PE2

PE3 PE4

PE5

PE6

PE14 PE15

PE9

PE8

PE11

PE10 PE12

PE13

PE7

PD0

PD1

PD3PD4 PD5 PD6 PD7

PD9

PD10

PD11

PD12

PD13

PD14 PD15

SB193Closed

PA2

PA5 PA6 PA7

PA10

PA3

PB1

PB3

PB4

PB8 PB9

PA11

PA12

PA9 PA8

PC4

PC5

PC6

PC7

PB5

PB6

PB14

PB15

PB2

PB11

PB12

PB13

PC8PC9

PB10

PD8

PF4

AGND

U5V

PF5

Morpho connector

SB195 Closed

PG0

PG1

PG2

PG3

PG4

PG5

PG14

PG9

PG8

PG11

PG10PG12 PG13

PG6

PG7

PG15

PF0

PF1 PF2

PF3

PF14

PF15

PF9

PF8

PF11

PF10

PF12

PF13

Morpho connector

TIMER_A_PWM1 TIMER_A_PWM2

TIMER_A_PWM3

Arduino Uno compatible

SB136 Closed SB137Closed

+3V3_PER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 37

39 41 43 45 47 49 51 53 55 57 59

42 44 46 48 50 52 54 56 58 60 62 64 66 68 70

61 63

67 69

34 36 38

71 72

CN11

Header 36X2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 37

39 41 43 45 47 49 51 53 55 57 59

42 44 46 48 50 52 54 56 58 60 62 64 66 68 70

61 63

67 69

34 36 38

71 72

CN12

Header 36X2

+3V3

SB110 Open

+3V3_PER

IOREF

Zio connector

Arduino Uno compatible

Zio connector

PA5SB123 Open

SB179 Closed

D43 D44 D45 D46 D47 D48 D49 D50

D72 D71 D70 D69 D68

D67 D66 D65

D51 D52 D53 D54 D55

D56 D57 D58 D59 D60 D61 D62 D63 D64

D16 D17 D18

D19 D20 D21

D22 D23 D24 D25

A6 A7

A8 D26 D27

D28 D29 D30 D31

D32 D33 D34 D35

D36

D37

D38

D39

D40

D41

D42

PB10

SB155 Closed

SB150 ClosedPA2

SB168 ClosedPE12

SB159 ClosedPB0

SB157 ClosedPE15

SB170 ClosedPE14

SB182 Closed SB188 Closed

SB177 Closed SB180 Closed

SB169 Closed

PC7

PB4

PA4

SB126 Closed

SB133 Closed

SB128 Closed

SB140 Closed

COMP2_IN P

SB147 Closed

SB136/SB 137 to avoid stub of SDMM C signals

SB192 Closed SB194 Closed SB196 Closed

SB191 Closed

PD8 PD9

VREF+

C45 [N/A]

SB119

Open

AGND

PH3-BOOT0

SB111 Open

PF3 PF5

SB112 Closed

VDD_MCU

SB144 Closed

SB144 to avoid stub of QSPI _IO1 signals

Figure 20. Extension connectors

UM2179 Electrical schematics

UM2179 Rev 8 49/55

Page 50

50/55 UM2179 Rev 8

SMPS powersupply

MB1312 A -01

2/21/2017

Title:

Size: Reference:

Date: Sheet: of

Revision:

NUCLEO-LXXXZXP roject:

VIN

CTRL

VOUT

VOUT2

GND

AUX

U9 ST1PS 02D1QTR

1IN

1S2

1S1

2IN

2S2

2S1

VCC

GND

U7 STG3684AU TR

VIN

VOUT

GND

U10 ST1PS01E JR

SMPS_V1

SMPS_EN

SMPS_PG

SMPS_SW

VOUTVDD VOUTCORE

U9 and U 15 are exclusively populated

SB7 Closed:If ADI5301(U15) is used or ST1P S02(U9) VOUT is used Open: If ST 1PS02(U9) VOUT2 is used

SB1 Closed:Default Open: If external switch

(U7)

SB8 Closed: Default Open:If using External SMP S onCN13

SB4 Open:Default Closed: If using External SMP S on CN13 and U7 is needed

SB11: Closed: If ST1PS02 (U9)VOUT2 isused Open: If ADI5301(U15) is used or ST1PS02(U9) VOUT is used

Mode SB10 SB118 SB115 SB117 SB9 Volt Ivdd

ST1PS02D Default Open Open Open Closed Closed 1.25 na DualVlowClosed Open Closed Open Open 1.05/1.15 50 DualVhi Open Closed Open Open Closed 1.05/1.25 100

PVIN

PGND

AGND

SYNC/MODE

VOUTOK

VID

U15 ADP5301AC BZ-2-R7

PVIN

PGND

AGND

SYNC/MODE

VOUTOK

VID

U16 ADP5301AC BZ-2-R7

U10and U16 are exclusive

D B A

Vout= 1.1V

VDD

VDD_1V2

VDDPG10

PG11

PG12

PG13

Componants mounted based on different board reference

PG[0..15]

C24 100nF

C23 100nF

SB125 Closed

SB120 Open

SB8 SB1

SB114

SB116

SB113 SB7

SB4 SB3

SB2

SB11

SB16

SB18

SB17

SB10

SB118

SB117

SB115 SB9

2.2uH[VLS 252010HBX-2R2M -1]

VDD_MCU

SB2 Closed:Default Open:

is needed

SB3 Open: Default Closed: If using External SMP S on CN13and U7 is not needed

Solder bridges default setting

Closed:SB1,SB2,SB7,SB8,SB16,SB17,SB18,SB114 Open:SB3, SB4, SB9, SB10, SB11,SB113, SB115,SB116, SB117, SB 118, SB129

ST1PS02(U9): Closed: SB8, SB9, SB11, SB16, SB17, SB18, SB117 Open: SB1, SB2, SB3, SB4, SB7, SB10, SB113, SB 114, SB115, SB 116, SB118, SB129

SB19

Open C25 10uF

C47 10uF

C22 10uF

C21 10uF

R35

19.6K[1%]

R53

11.8K[1%]

R33 0

R34

R32

33K

SB122 Closed

SB121 Open

SB127 Open

C48

100nF

SB129

C46 10uF[N/A]

6 5

4 3

2 1

8 7

CN13

Header 4X2[N/A ]

Figure 21. SMPS power supply

Electrical schematics UM2179

is needed

efault volatge will be V out = 1.2V UT Some board to be equiped with DP5301_Opt1 andR53= 25.5K for

DI5301(U15):

f external sw itch (U7)

Page 51

UM2179 Board revision history and limitations

Appendix B Board revision history and limitations

Table 13. Board revision history and limitations

Board Version Revision details Known limitations

A4/A5 on ARDUINO

MB1312 A-04 Initial version

connector CN9 cannot be used as I2C function.

A4/A5 on ARDUINO connector CN9 cannot be used as I2C function.

MB1312 (SMPS) A-03

Initial version for NUCLEO-L496ZG-P

Uno V3

UM2179 Rev 8 51/55

Page 52

Federal Communications Commission (FCC) and Industry Canada (IC) Compliance UM2179

Appendix C Federal Communications Commission (FCC)

and Industry Canada (IC) Compliance

This kit is designed to allow:

• (1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and

• (2) Software developers to write software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of 47 CFR, Chapter I (“FCC Rules”), the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.

52/55 UM2179 Rev 8

Page 53

UM2179 Revision history

Revision history

Table 14. Document revision history

Date Revision Changes

28-Feb-2017 1 Initial version.

Document now also scopes NUCLEO-L496ZG-P product. Added:

Section 6.5.4: SMPS power supply Figure 12: NUCLEO-L496ZG-P

Updated: – cover page features (to cover LL library) – cover page description – Section 1: Features (SMPS function)

27-Mar-2017 2

– Section 6.6: LEDs – Section 6.13: Solder bridges and jumpers – Section Appendix B: Board revision history and limitations – Table 1: Ordering information – Table 2: Codification explanation – Table 11: NUCLEO-L496ZG, NUCLEO-L496ZG-P and

NUCLEO-L4R5ZI pin assignments

– Figure 3: Hardware block diagram – Figure 4: STM32 Nucleo-144 board top layout – Figure 5: STM32 Nucleo-144 board bottom layout

Document now also scopes NUCLEO-L4R5ZI product. Added Figure 13: NUCLEO-L4R5ZI.

08-Aug-2017 3

Updated: – The cover page Introduction – Table 1: Ordering information – Table 2: Codification explanation

31-Aug-2017 4 Updated Table 1: Ordering information.

7-Nov-2017 5

Updated Chapter 2: Product marking. Added Section 6.17:

Bootloader limitation.

Expanded document scope to the NUCLEO-L4A6ZG product: – Updated Introduction

15-Dec-2017 6

– Updated Table 1: Ordering information and Table 11:

NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI and NUCLEO-L4A6ZG pin assignments

– Added Figure 13: NUCLEO-L4A6ZG

UM2179 Rev 8 53/55

Page 54

Revision history UM2179

Table 14. Document revision history (continued)

Date Revision Changes

Expanded document scope to the NUCLEO-L4R5ZI-P product: – Updated Introduction – Updated Section 6.5.4: SMPS power supply

1-Feb-2018 7

17-Sep-2019 8

– Updated Table 1: Ordering information and Table 11:

NUCLEO-L496ZG, NUCLEO-L496ZG-P, NUCLEO-L4R5ZI, NUCLEO-L4R5ZI-P and NUCLEO-L4A6ZG pin assignments

– Added Figure 15: NUCLEO-L4R5ZI-P

Added a caution about the power sequence not being respected when using 1V8 MCU_VDD in Section 5.5.4: SMPS

power supply.

Reorganized the beginning of the document from Introduction to Section 4: Conventions . Updated the document title. Updated Section 1: Features, Table 1: Ordering information, and Table 2: Codification explanation.

54/55 UM2179 Rev 8

Page 55

UM2179

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

UM2179 Rev 8 55/55