STIHL FS 460 C-M Owner's Manual
STIHL FS 460 C-M
{
Instruction Manual
Manual de instrucciones
Warning!
Read and follow all safety
precautions in Instruction Manual –
improper use can cause serious or
fatal injury.
Advertencia!
Lea y siga todas las precauciones
de seguridad dadas en el manual
de instrucciones – el uso incorrecto
puede causar lesiones graves o
mortales.
Instruction Manual
1 - 47
Manual de
instrucciones
49 - 99
Contents
English
Guide to Using this Manual 2
Safety Precautions and Working
Techniques 3
Approved Combinations of Cutting
Attachment, Deflector, Limit Stop
and Harness 16
Mounting the Bike Handle 17
Mounting the Deflector 20
Mounting the Cutting Attachment 21
Original Instruction ManualPrinted on chlorine-free paper
Fuel 24
Fueling 25
Fitting the Full Harness 26
Balancing the Trimmer/Brushcutter 27
Starting / Stopping the Engine 27
Operating Instructions 29
Cleaning the Air Filter 30
Engine Management 30
M-Tronic 31
Winter Operation 31
Spark Plug 32
Engine Running Behavior 34
Replacing the Starter Rope and
Printing inks contain vegetable oils, paper can be recycled.
Rewind Spring 34
Storing the Machine 36
Sharpening Metal Cutting Blades 37
Inspection and Maintenance by
User 37
Inspections and Maintenance by
Dealer 38
Maintenance and Care 39
Main Parts 41
Specifications 43
Special Accessories 44
Maintenance and Repairs 44
STIHL Incorporated Federal
Emission Control Warranty
Statement 44
Trademarks 46
Allow only persons who fully understand
this manual to operate your trimmer /
brushcutter.
To receive maximum performance and
satisfaction from your STIHL trimmer /
brushcutter, it is important that you read,
understand and follow the safety
precautions and the operating and
maintenance instructions in chapter
"Safety Precautions and Working
Techniques" before using your trimmer /
brushcutter. For further information you
can go to www.stihlusa.com.
Contact your STIHL dealer or the STIHL
distributor for your area if you do not
understand any of the instructions in this
manual.
Warning!
Because a trimmer / brushcutter is a
high-speed cutting tool some special
safety precautions must be observed to
reduce the risk of personal injury. Careless or improper use may cause serious
or even fatal injury.
Make sure your unit is equipped with the
proper deflector, handle and harness for
the type of cutting attachment being
used. Always wear proper eye
protection.
{
© ANDREAS STIHL AG & Co. KG, 2010
0458-746-8621-A. M0-4.L10.DDS.
0000003859_002_GB
FS 460 C-M, FS 460 C-M L
1
English
Guide to Using this Manual
Pictograms
The meanings of the pictograms
attached to or embossed on the
machine are explained in this manual.
Depending on the model concerned, the
following pictograms may be on your
machine.
Fuel tank for gasoline
and engine oil mixture
Press to operate decompression valve
Manual fuel pump
Press to operate manual
fuel pump
Symbols in Text
Many operating and safety instructions
are supported by illustrations.
The individual steps or procedures
described in the manual may be marked
in different ways:
N A bullet marks a step or procedure.
A description of a step or procedure that
refers directly to an illustration may
contain item numbers that appear in the
illustration. Example:
N Loosen the screw (1).
N Lever (2) ...
In addition to the operating instructions,
this manual may contain paragraphs
that require your special attention. Such
paragraphs are marked with the
symbols and signal words described
below:
Danger!
Indicates an imminent risk of severe or
fatal injury.
Engineering Improvements
STIHL’s philosophy is to continually
improve all of its products. As a result,
engineering changes and improvements
are made from time to time. Therefore,
some changes, modifications and
improvements may not be covered in
this manual. If the operating
characteristics or the appearance of
your machine differs from those
described in this manual, please contact
your STIHL dealer for assistance.
Filler hole for gear
lubricant
Air intake summer mode
Air intake winter mode
Handle heating
2
Warning!
Indicates a hazardous situation which, if
not avoided, could result in severe or
fatal injury.
Caution!
Indicates a risk of property damage,
including damage to the machine or its
individual components.
FS 460 C-M, FS 460 C-M L
English
Safety Precautions and
Working Techniques
Because a clearing saw
is a high-speed, fast-cutting power tool
sometimes equipped with
sharp cutting blades,
special safety precautions must be observed to
reduce the risk of personal injury.
It is important that you
read, fully understand
and observe the following
safety precautions and
warnings. Read the
instruction manual and
the safety precautions
periodically. Careless or
improper use may cause
serious or fatal injury.
The terminology utilized in this manual
when referring to the power tool reflects
the fact that different types of cutting
attachments may be mounted on it. The
term "trimmer" is used to designate an
FS unit that is equipped with a nylon line
head or a head with flexible plastic
blades (i.e., the PolyCut head). A
"brushcutter" designates a unit
equipped with a rigid metal blade. Many
FS models may be used as either a
trimmer or a brushcutter – therefore, the
power tool is referred in this manual as a
"trimmer / brushcutter." Some smaller
and / or lightweight FS models may only
be used as a trimmer, i.e., they may not
be used with metal blades.
The term "clearing saw" indicates a
high-powered trimmer / brushcutter that
is particularly suited for use with a
circular saw blade to clear saplings or
small trees.
Warning!
As more fully explained later in these
Safety Precautions, to reduce the risk of
personal injury, make sure your unit is
equipped with the proper deflector, limit
stop and harness for the type of cutting
attachment you are using. Use only cutting attachments that are specifically
authorized by STIHL for use on your FS
model.
Have your STIHL dealer show you how
to operate your power tool. Observe all
applicable local safety regulations,
standards and ordinances.
Warning!
Do not lend or rent your power tool without the instruction manual. Be sure that
anyone using it understands the information contained in this manual.
Warning!
The use of this machine may be hazardous. If the rotating line or blade comes in
contact with your body, it will cut you.
When it comes in contact with solid foreign objects such as rocks or bits of
metal, it may fling them directly or by ricochet in the direction of bystanders or
the operator. Striking such objects could
damage the cutting attachment and may
cause blades to crack, chip or break.
Thrown objects, including broken heads
or blades, may result in serious or fatal
injury to the operator or bystanders.
STIHL does not recommend the use of
rigid blades when cutting in stony areas.
Use your clearing saw equipped with the
appropriate cutting attachment only for
cutting grass, brush, wood and similar
material.
Warning!
Do not use it for other purposes, since
misuse may result in personal injury or
property damage, including damage to
the machine.
Warning!
Minors should never be allowed to use
this power tool. Bystanders, especially
children, and animals should not be
allowed in the area where it is in use.
FS 460 C-M, FS 460 C-M L
3
English
Warning!
To reduce the risk of injury to bystanders and damage to property, never let
your power tool run unattended. When it
is not in use (e.g. during a work break),
shut it off and make sure that unauthorized persons do not use it.
Most of these safety precautions and
warnings apply to the use of all STIHL
clearing saws. Different models may
have different parts and controls. See
the appropriate section of your
instruction manual for a description of
the controls and the function of the parts
of your model.
Safe use of a clearing saw involves
1. the operator
2. the power tool
3. the use of the power tool.
THE OPERATOR
Physical Condition
You must be in good physical condition
and mental health and not under the
influence of any substance (drugs,
alcohol, etc.) which might impair vision,
dexterity or judgment. Do not operate
this machine when you are fatigued.
Warning!
Be alert – if you get tired, take a break.
Tiredness may result in loss of control.
Working with any power tool can be
strenuous. If you have any condition
that might be aggravated by strenuous
work, check with your doctor before
operating this machine.
Warning!
Prolonged use of a power tool (or other
machines) exposing the operator to
vibrations may produce whitefinger disease (Raynaud's phenomenon) or
carpal tunnel syndrome.
These conditions reduce the hand's
ability to feel and regulate temperature,
produce numbness and burning
sensations and may cause nerve and
circulation damage and tissue necrosis.
All factors which contribute to
whitefinger disease are not known, but
cold weather, smoking and diseases or
physical conditions that affect blood
vessels and blood transport, as well as
high vibration levels and long periods of
exposure to vibration are mentioned as
factors in the development of whitefinger
disease. In order to reduce the risk of
whitefinger disease and carpal tunnel
syndrome, please note the following:
– Most STIHL power tools are
available with an anti-vibration
("AV") system designed to reduce
the transmission of vibrations
created by the machine to the
operator's hands. An AV system is
recommended for those persons
using power tools on a regular or
sustained basis.
– Wear gloves and keep your hands
warm.
– Keep the AV system well
maintained. A power tool with loose
components or with damaged or
worn AV elements will tend to have
higher vibration levels.
– Maintain a firm grip at all times, but
do not squeeze the handles with
constant, excessive pressure. Take
frequent breaks.
All the above-mentioned precautions do
not guarantee that you will not sustain
whitefinger disease or carpal tunnel
syndrome. Therefore, continual and
regular users should closely monitor the
condition of their hands and fingers. If
any of the above symptoms appear,
seek medical advice immediately.
Warning!
The ignition system of the STIHL unit
produces an electromagnetic field of a
very low intensity. This field may interfere with some pacemakers. To reduce
the risk of serious or fatal injury, persons
with a pacemaker should consult their
physician and the pacemaker manufacturer before operating this tool.
4
FS 460 C-M, FS 460 C-M L
English
Proper Clothing
To reduce the risk of injury, the operator
should wear proper protective apparel.
Warning!
The deflector provided with your power
tool will not protect the operator from all
foreign objects (gravel, glass, wire, etc.)
thrown back by the rotating cutting
attachment. Thrown objects may also
ricochet and strike the operator.
Warning!
To reduce the risk of
injury to your eyes never
operate your power tool
unless wearing goggles
or properly fitted protec-
tive glasses with
adequate top and side protection complying with ANSI Z 87.1 (or your
applicable national standard). To
reduce the risk of injury to your face
STIHL recommends that you also wear
a face shield or face screen over your
goggles or protective glasses.
Wear an approved safety hard hat to
reduce the risk of injury to your head
when there is a danger of head injuries.
Power tool noise may damage your
hearing. Wear sound barriers (ear plugs
or ear mufflers) to protect your hearing.
Continual and regular users should
have their hearing checked regularly.
Be particularly alert and cautious when
wearing hearing protection because
your ability to hear warnings (shouts,
alarms, etc.) is restricted.
Always wear gloves
when handling the
machine and metal
blades. Heavy-duty, nonslip gloves improve your
grip and help to protect
your hands.
Clothing must be sturdy
and snug-fitting, but allow
complete freedom of
movement. Wear long
pants made of heavy
material to help protect
your legs. Do not wear
shorts, sandals or go
barefoot.
Avoid loose-fitting jackets, scarfs,
neckties, jewelry, flared or cuffed pants,
unconfined long hair or anything that
could become caught on branches,
brush or the moving parts of the unit.
Secure hair so it is above shoulder level.
Good footing is very
important. Wear sturdy
boots with nonslip soles.
Steel-toed safety boots
are recommended.
THE POWER TOOL
For illustrations and definitions of the
power tool parts see the chapter on
"Main Parts."
Warning!
Never modify this power tool in any way.
Only attachments supplied by STIHL
and expressly approved by STIHL for
use with the specific STIHL model are
authorized. Although certain unauthorized attachments are useable with
STIHL power tools, their use may, in
fact, be extremely dangerous. For the
cutting attachments authorized by
STIHL for your unit, see the chapter
"Approved Combinations of Cutting
Attachment, Deflector, Limit Stop and
Harness" in the instruction manual or
the STIHL "Cutting Attachments, Parts
& Accessories" catalog.
If this tool is subjected to unusually high
loads for which it was not designed (e.g.
heavy impact or a fall), always check
that it is in good condition before
continuing work. Check in particular that
the fuel system is tight (no leaks) and
that the controls and safety devices are
working properly. Do not continue
operating this machine if it is damaged.
In case of doubt, have it checked by your
STIHL servicing dealer.
THE USE OF THE POWER TOOL
Transporting the Power Tool
Warning!
To reduce the risk of injury from loss of
control and blade or line contact, never
carry or transport your power tool with
the cutting attachment moving.
FS 460 C-M, FS 460 C-M L
5
English
It may be carried only in a horizontal
position. Grip the shaft in a manner that
the machine is balanced horizontally.
Keep the hot muffler away from your
body and the cutting attachment behind
you.
Warning!
To reduce the risk of
burn injury, do not touch
hot parts of the machine
and the gear housing
when they are hot.
Warning!
Always shut off the engine and make
sure the cutting attachment has stopped
before putting a clearing saw down.
When transporting it in a vehicle, properly secure it to prevent turnover, fuel
spillage and damage to the unit. STIHL
recommends that you keep metal
blades covered with the transport guard
(optional accessory).
Fuel
Your STIHL power tool uses an oilgasoline mixture for fuel (see the
chapter on "Fuel" of your instruction
manual).
Warning!
Gasoline is an extremely
flammable fuel. If spilled
and ignited by a spark or
other ignition source, it
can cause fire and seri-
002BA272 KN
property damage. Use extreme caution
ous burn injury or
when handling gasoline or fuel mix. Do
not smoke or bring any fire or flame near
the fuel or the power tool. Note that
combustible fuel vapor may escape
from the fuel system.
Fueling Instructions
Warning!
Fuel your power tool in well-ventilated
areas, outdoors. Always shut off the
engine and allow it to cool before refueling. Gasoline vapor pressure may
build up inside the fuel tank depending
on the fuel used, the weather conditions
and the tank venting system.
In order to reduce the risk of burns and
other personal injury from escaping gas
vapor, remove the fuel filler cap on your
power tool carefully so as to allow any
pressure build-up in the tank to release
slowly. Never remove the fuel filler cap
while the engine is running.
Select bare ground for fueling and move
at least 10 feet (3 m) from the fueling
spot before starting the engine. Wipe off
any spilled fuel before starting your
machine.
Warning!
Check for fuel leakage
while refueling and during operation. If fuel
leakage is found, do not
start or run the engine
until the leak is fixed and
any spilled fuel has been wiped away.
Take care not to get fuel on your clothing. If this happens, change your
clothing immediately.
Cap with Grip
Warning!
In order to reduce the risk of fuel spillage and fire from an improperly
tightened fuel cap, correctly position
and tighten the fuel cap in the fuel tank
opening.
To do this with this STIHL
cap, raise the grip on the
top of the cap until it is
upright at a 90° angle.
Insert the cap in the fuel
tank opening with the triangular marks on the grip
of the cap and on the fuel
tank opening lining up.
Using the grip, turn the
cap firmly clockwise as
far as it will go (approx. a
quarter turn).
6
FS 460 C-M, FS 460 C-M L
English
Fold the grip flush with
the top of the cap. If the
grip does not lie completely flush with the cap
and the detent on the grip
does not fit in the corresponding recess in the
filler opening, the cap is
not properly seated and
tightened and you must
repeat the above steps.
Before Starting
Warning!
Always check your power tool for proper
condition and operation before starting,
particularly the throttle trigger, throttle
trigger lockout, momentary stop switch,
cutting attachment, deflector and harness. The throttle trigger must move
freely and always spring back to the idle
position. Never attempt to modify the
controls or safety devices.
Warning!
Never operate your power tool if it is
damaged, improperly adjusted or maintained, or not completely or securely
assembled.
Warning!
Do not attach any cutting attachment to
a unit without proper installation of all
required parts. Failure to use the proper
parts may cause the blade or head to fly
off and seriously injure the operator or
bystanders.
Warning!
The cutting attachment must be properly tightened and in safe operating
condition. Inspect for loose parts (nuts,
screws, etc.) and for cracked or damaged heads or cracked, bent, warped or
damaged blades. Replace damaged
heads or blades before using the power
tool. Always keep blades sharp.
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, fuel mix,
grease or resin in order for you to
maintain a firm grip and properly control
your power tool.
Warning!
Check that the spark plug boot is
securely mounted on the spark plug – a
loose boot may cause arcing that could
ignite combustible fumes and cause a
fire.
Warning!
To reduce the risk
of personal injury
to the operator
from blade or line
contact and
thrown objects, make sure your unit is
equipped with the proper deflector, limit
stop and harness for the type of cutting
attachment being used (see chart in the
chapter on "Approved Combinations of
Cutting Attachment, Deflector, Limit
Stop and Harness").
As can be seen in that chart, some
cutting attachments may require you to
change your deflector, limit stop and / or
harness.
Keep the deflector (and the attached
skirt where appropriate) adjusted
properly at all times (see chapters on
"Mounting the Deflector" and "Mounting
the Cutting Attachment" of your
instruction manual).
A
000BA006 KN
B
000BA007 KN
Arrows on the deflector (A) and limit
stop (B) (as seen from the underside)
show the correct direction of rotation of
the cutting attachment. When viewed
from above, however, the cutting
attachment rotates counterclockwise.
Some of the following symbols may be
embossed on the outside of the deflector
in order to indicate the approved
combination of cutting attachment and
deflector.
FS 460 C-M, FS 460 C-M L
7
English
The deflector may be
used in combination with
mowing heads.
The deflector may be
used in combination with
grass cutting blades.
The deflector may be
used in combination with
brush knives.
The deflector must not be
used in combination with
mowing heads.
The deflector must not be
used in combination with
grass cutting blades.
The deflector must not be
used in combination with
brush knives.
The deflector must not be
used in combination with
circular saw blades.
proper control and less fatigue in
operation. To be better prepared in case
of an emergency, practice releasing the
unit from the harness as quickly as
possible.
Starting
Start the engine at least 10 feet (3 m)
from the fueling spot, outdoors only.
For specific starting instructions, see the
appropriate section of your manual.
Place the power tool on firm ground or
other solid surface in an open area.
Maintain good balance and secure
footing.
Warning!
To reduce the risk of injury from blade or
line contact, be absolutely sure that the
cutting attachment is clear of you and all
other obstructions and objects, including the ground, because when the
engine starts at starting-throttle, engine
speed will be fast enough for the clutch
to engage and move the cutting
attachment.
Once the engine has started,
immediately blip the throttle trigger,
which should release the starting throttle
and allow the engine to slow down to
idle.
With the engine running only at idle,
attach the power tool to the spring hook
of your harness (see appropriate
chapter of this manual).
Warning!
Your power tool is a one-person
machine. Do not allow other persons in
the general work area, even when
starting.
Warning!
To reduce the risk of injury from loss of
control, do not attempt to "drop start"
your power tool.
Warning!
When you pull the starter grip, do not
wrap the starter rope around your hand.
Do not let the grip snap back, but guide
the starter rope to rewind it properly.
Failure to follow this procedure may
result in injury to your hand or fingers
and may damage the starter
mechanism.
Important Adjustments
Warning!
To reduce the risk of personal injury
from loss of control or contact with the
running cutting attachment, do not use
your unit with incorrect idle speed. At
correct idle speed, the cutting attachment should not move.
If your power tool shows an incorrect idle
speed, have your STIHL dealer check
your power tool and make proper
adjustments and repairs.
Adjust carrying harness and hand grip to
suit your size before starting work. The
machine should be properly balanced as
specified in your instruction manual for
8
FS 460 C-M, FS 460 C-M L
English
Warning!
This unit is equipped with an ignition
system that is normally in operational
readiness. After the setting lever is used
to stop the engine, it automatically
springs back to the "on" position. If the
engine is warm, it may be possible to
start it by simply pulling the starter rope,
with no further adjustments. To reduce
the risk of injury, be particularly alert to
keep children away from the unit.
During Operation
Holding and Controlling the Power
Tool
Always hold the unit firmly with both
hands on the handles while you are
working. Wrap your fingers and thumbs
around the handles, keeping the
handles cradled between your thumb
and forefinger.
Warning!
Never attempt to operate
your power tool with one
hand. Loss of control of
the power tool resulting in
serious or fatal injury may
result. To reduce the risk
of cut injuries, keep hands and feet
away from the cutting attachment.
Never touch a moving cutting attachment with your hand or any other part of
your body.
Warning!
Do not overreach. Keep proper footing
and balance at all times. Special care
must be taken in slippery conditions
(wet ground, snow) and in difficult, overgrown terrain. Watch for hidden
obstacles such as tree stumps, roots
and ditches to avoid stumbling. For better footing, clear away scrub and
cuttings. Be extremely cautious when
002BA257 KN
working on slopes or uneven ground.
Warning!
To reduce the risk of injury from loss of
control, never work on a ladder or on
any other insecure support. Never hold
the cutting attachment above waist
height.
Warning!
As soon as the engine is
running, this product generates toxic exhaust
fumes containing chemicals, such as unburned
hydrocarbons (including
benzene) and carbon monoxide, that
are known to cause respiratory problems, cancer, birth defects, or other
reproductive harm. Some of the gases
(e.g. carbon monoxide) may be colorless and odorless. To reduce the risk of
serious or fatal injury / illness from inhaling toxic fumes, never run the machine
indoors or in poorly ventilated locations.
Warning!
If the vegetation being cut or the surrounding ground is coated with a
chemical substance (such as an active
pesticide or herbicide), read and follow
the instructions and warnings that
accompanied the substance at issue.
FS 460 C-M, FS 460 C-M L
Working Conditions
Operate and start your power tool only
outdoors in a well-ventilated area.
Operate it under good visibility and
daylight conditions only. Work carefully.
9
English
Warning!
Inhalation of certain dusts, especially
organic dusts such as mold or pollen,
can cause susceptible persons to have
an allergic or asthmatic reaction. Substantial or repeated inhalation of dust
and other airborne contaminants, in particular those with a smaller particle size,
may cause respiratory or other illnesses. Control dust at the source
where possible. Use good work practices, such as operating the unit so that
the wind or operating process directs
any dust raised by the power tool away
from the operator. Follow the recommendations of EPA / OSHA / NIOSH
and occupational and trade associations with respect to dust ("particulate
matter"). When the inhalation of dust
cannot be substantially controlled, i.e.,
kept at or near the ambient (background) level, the operator and any
bystanders should wear a respirator
approved by NIOSH / MSHA for the type
of dust encountered.
Operating Instructions
Warning!
Do not operate your power tool using
the starting throttle position, as you do
not have control of the engine speed.
In the event of an emergency, shut off
the engine immediately – move the
momentary stop switch to STOP.
Warning!
The cutting attachment
continues to rotate for a
short period after the
throttle trigger is
released (flywheel
effect.
Warning!
The rotating cutting attachment may
fling foreign objects directly or by ricochet a great distance.
15m (50ft)
To reduce the risk of eye and other injury
always wear proper eye protection (see
the chapter on "Proper Clothing") and
ensure that bystanders are at least
50 feet (15 m) away. To reduce the risk
of damage to property, also maintain this
distance from such objects as vehicles
or windows. Any coworkers who must be
in the restricted area should also wear
goggles or protective glasses. Stop the
engine immediately if you are
approached.
Warning!
Before you start work,
examine the area for
stones, glass, fence
wire, metal, trash or
other solid objects. The
cutting attachment could
throw objects of this kind.
Warning!
This clearing saw is normally to be used
at ground level with the cutting attachment parallel to the ground. Use of a
clearing saw above ground level or with
the cutting attachment perpendicular to
the ground may increase the risk of
injury, since the cutting attachment is
more fully exposed and the power tool
may be more difficult to control. Never
use your clearing saw as a hedge
trimmer.
Warning!
During cutting, check the tightness and
the condition of the cutting attachment
at regular short intervals with the engine
and attachment stopped. If the behavior
of the attachment changes during use,
stop the engine immediately, wait until
the cutting attachment stops, and check
the nut securing the attachment for
tightness and the blade or head for
cracks, wear and damage.
10
FS 460 C-M, FS 460 C-M L
English
Warning!
A loose blade or head may vibrate,
crack, break or come off the clearing
saw, which may result in serious or fatal
injury. Make sure that the cutting attachment is properly tightened. Use the
wrench supplied or one of sufficient
length to obtain the proper torque. If the
blade or head loosens after being properly tightened, stop work immediately.
The retaining nut may be worn or damaged and should be replaced. If the
blade or head continues to loosen, see
your STIHL dealer. Never use a clearing
saw with a loose cutting attachment.
Warning!
Replace a cracked, damaged or wornout head or a cracked, bent, warped,
damaged, dull or worn out blade immediately, even if damage is limited to
superficial cracks. Such attachments
may shatter at high speed and cause
serious or fatal injury.
Warning!
When using rigid blades, avoid cutting
close to fences, sides of buildings, tree
trunks, stones or other such objects that
could cause the power tool to kick out or
could cause damage to the blade.
STIHL recommends use of the nylon
line heads for such jobs. In addition, be
alert to an increased possibility of ricochets in such situations.
Warning!
If the head, blade or deflector becomes
clogged or stuck, always shut off the
engine and make sure the cutting
attachment has stopped before cleaning. Grass, weeds, etc. should be
cleaned off the blade or from around the
head at regular intervals.
Warning!
To reduce the risk of unintentional rotation of the cutting attachment and injury,
always shut off the engine and remove
the spark plug boot before replacing the
cutting attachment. To reduce the risk of
injury, always shut off the engine before
adjusting the length of the nylon line on
manually adjustable mowing heads.
Warning!
Do not turn the engine on over the
starter with the spark plug boot or spark
plug removed since there is otherwise a
risk of fire from uncontained sparking.
Warning!
The gearbox becomes hot during operation. To reduce the risk of burn injury,
do not touch the gear housing when it is
hot.
Warning!
The muffler and other parts of the
engine (e.g. fins of the cylinder, spark
plug) become hot during operation and
remain hot for a while after stopping the
engine. To reduce risk of burns do not
touch the muffler and other parts while
they are hot.
Warning!
To reduce the risk of fire and burn injury,
keep the area around the muffler clean.
Remove excess lubricant and all debris
such as pine needles, branches or
leaves. Let the engine cool down sitting
on concrete, metal, bare ground or solid
wood away from any combustible
substances.
Warning!
Never modify your muffler. The muffler
could be damaged and cause an
increase in heat radiation or sparks,
thereby increasing the risk of fire and
burn injury. You may also permanently
damage the engine. Have your muffler
serviced and repaired by your STIHL
servicing dealer only.
USING THE CUTTING ATTACHMENT
For an illustration of the various cutting
attachments and instructions on proper
mounting see the chapter on "Mounting
the Cutting Attachment" in your
instruction manual.
FS 460 C-M, FS 460 C-M L
11
English
Warning!
To reduce the risk of severe or fatal
injury from blade contact and / or loss of
control, never attempt to use a metal
blade on an FS model for which it is not
authorized.
Using the Mowing Heads
Do not use with mowing line longer than
the intended length. With a properly
mounted deflector, the built-in linelimiting blade will automatically adjust
the line to its proper length.
Using the unit with an overly long nylon
cutting line increases the load on the
engine and reduces its operating speed.
This causes the clutch to slip
continuously and results in overheating
and damage to important components
(e.g. clutch, polymer housing
components). Such damage could,
among other things, cause the cutting
attachment to rotate at idle.
Mowing heads are to be used only on
clearing saws equipped with a linelimiting blade in the deflector in order to
keep the line at the proper length (see
"Main Parts" chapter in your instruction
manual).
If the lawn edges are planted with trees
or bordered by a fence etc., it is best to
use a nylon line head. It achieves a
"softer" cut with less risk of damaging
tree bark etc. than polymer blades.
However, the polymer-bladed STIHL
PolyCut produces a better cut if there
are no plants along the edge of the lawn.
Sharpening is not necessary, and worn
polymer blades are easily replaced.
Warning!
To reduce the risk of serious injury,
never use wire or metal-reinforced line
or other material in place of the nylon
cutting lines. Pieces of wire could break
off and be thrown at high speed toward
the operator or bystanders.
STIHL SuperCut mowing head
Fresh line is advanced automatically.
Frayed line is replaced by a simple
adjustment (see instruction sheet
supplied with mowing head).
STIHL AutoCut mowing head
Nylon cutting line advances
automatically when tapped against the
ground (TapAction).
STIHL TrimCut mowing head
Frayed line is replaced by a simple
adjustment (see instruction sheet
002BA354 KN
supplied with mowing head).
STIHL PolyCut mowing head
002BA396 KN
Uses either nylon lines or nonrigid,
pivoting polymer blades.
Observe wear indicators.
Warning!
Three rectangular wear limit marks are
applied to the base (periphery) of the
PolyCut. To reduce the risk of serious
injury from breakage of the head or
blades, the PolyCut must not be used
when it has worn as far as one of these
marks. It is important to follow the maintenance instructions supplied with the
head.
Warning!
If the wear limit marks are ignored, there
is a risk of the cutting attachment shattering and flying parts injuring the
operator or bystanders. To reduce the
risk of accidents from shattered blades,
avoid contact with stones, metal and
similar solid objects. Check PolyCut
blades for cracks at regular intervals. If
a crack is found on one blade, always
replace all blades.
12
FS 460 C-M, FS 460 C-M L
English
Risk of Kickout (Blade Thrust) with all
Rigid Cutting Blades
Warning!
Kickout (blade thrust) is the sudden and
uncontrolled motion towards the operator's right or rear that can occur when
the shaded area (especially the darkly
shaded area) of a rotating blade comes
in contact with a solid rigid object like a
tree, rock, bush or wall. The rapid counterclockwise rotation of the blade may
be stopped or slowed, and the cutting
attachment may be thrown to the right or
to the rear.
This kickout (blade thrust) may cause
loss of control of the power tool and may
result in serious or fatal injury to the
operator or bystanders. To reduce the
risk of injury, extreme caution should be
used when cutting with the shaded area
of any rigid blade.
Using the Grass Cutting Blade
002BA135 KN
All kinds of grass and weeds can be
easily cut with the grass cutting blade.
The power tool is swept in an arc similar
to a scythe.
Warning!
To reduce the risk of serious or fatal
injury from blade breakage, never
attempt to use this blade to cut woody
materials.
The 4-tooth grass cutting blade is
intended to cut grass and weeds. It has
4 cutting knives with cutting edges on
both sides, i.e. front and rear. When the
cutting edges on one side become dull,
the blade can be turned over to utilize
the cutting edges on the other side.
The 8-tooth grass cutting blade is
recommended for cutting fern or reed.
Both types of grass cutting blade have to
be resharpened when all cutting edges
are dull.
Using the Brush Knife
When fitted to the power tool, the brush
knife is suitable for applications ranging
from cutting matted grass to clearing
weeds, wild growth and scrub.
002BA355 KN
To cut wild growth and scrub, lower the
rotating brush knife down onto the
growth to achieve a chopping effect –
but keep the tool below waist height at
all times.
Warning!
Exercise extreme caution when using
this method of cutting. The higher the
cutting attachment is off the ground, the
greater the risk of loss of control and of
cuttings being thrown sideways.
Use the power tool like a scythe to cut
grass, i.e. sweep it to and fro in an arc.
Warning!
When cutting woody materials, use the
left side of the blade to avoid "kickout"
(blade thrust) situations.
Warning!
Improper use of a brush knife may
cause it to crack, chip or shatter.
Thrown blade fragments may seriously
or fatally injure the operator or bystanders. To reduce the risk of injury, avoid
contact with hard or solid foreign objects
such as stones, rocks or pieces of
metal.
002BA066 KN
FS 460 C-M, FS 460 C-M L
13
English
Warning!
When cutting young saplings or other
woody materials up to 2 cm (3/4 in.) in
diameter, use the left side of the blade
to avoid "kickout" situations (see section
on "Risk of kickout (blade thrust) with all
rigid cutting blades"). Do not attempt to
cut woody material with a larger diameter, since the blade may catch or jerk the
power tool forward. This may cause
damage to the blade or power tool or
loss of control of the power tool, resulting in personal injury. Use a circular saw
blade for such work.
Warning!
Inspect the brush knife at regular short
intervals for signs of damage. Do not
continue working with a damaged brush
knife. Resharpen the brush knife regularly (when it has dulled noticeably).
Using the Circular Saw Blade
loss of control of the power tool and
result in serious injury. Use a chain saw
for such work.
Warning!
To reduce the risk that the blade will
crack and / or break, avoid all contact
with stones, rocks or the ground.
Sharpen blades in a timely manner as
specified – dull teeth may cause the
blade to crack or shatter.
When a clearing saw with a circular saw
blade is used to cut down small trees,
STIHL recommends that the standard
deflector be removed and replaced by
the special limit stop deflector (see
chapter on "Mounting the Deflector").
This limit stop helps to keep the unit
positioned against the tree during the
cutting process. Inexperienced users
should place the left side of the stop
against the tree trunk before beginning
to cut. This will keep the clearing saw
against the tree during the cutting
operation and will reduce the risk of loss
of control and possible kickout
(described above and briefly again
below).
be applied to the right of the tree, using
the non-shaded area of the blade, as
shown in the illustration above.
002BA068 KN
Warning!
The risk of kickout is highest when cutting in the darker shaded area. To
reduce the risk of kickout and resulting
injury, do not use this area of the circular
saw blade for cutting trees or shrubs.
Special techniques using the lighter
shaded areas of the blade to cut shrubs
and trees should only be used by experienced operators with specialized
training in the use and control of the
clearing saw.
When felling small trees, maintain a
distance of at least two tree lengths from
the nearest coworker.
Circular saw blades are suitable for
thinning brush and cutting small trees up
to a diameter of 7 cm (2 3/4 in.). Do not
attempt to cut trees with larger
diameters, since the blade may catch or
jerk the trimmer / brushcutter forward.
This may cause damage to the blade or
14
002BA067 KN
Before starting the cut, accelerate the
engine up to full throttle. Perform cut
with uniform pressure. STIHL
recommends that the circular saw blade
Warning!
In order to reduce the risk of injury from
thrown objects or operator contact with
the blade or head, be sure to remount
the standard deflector when no longer
using a circular saw blade.
002BA214 ST
FS 460 C-M, FS 460 C-M L
English
MAINTENANCE, REPAIR AND
STORING
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
nonroad engine repair establishment
or individual. However, if you make a
warranty claim for a component
which has not been serviced or
maintained properly or if
nonapproved replacement parts were
used, STIHL may deny coverage.
Warning!
Use only identical STIHL replacement
parts for maintenance and repair. Use of
non-STIHL parts may cause serious or
fatal injury.
Strictly follow the maintenance and
repair instructions in the appropriate
sections of your instruction manual.
Warning!
Always stop the engine and make sure
that the cutting attachment is stopped
before doing any maintenance or repair
work or cleaning the power tool. Do not
attempt any maintenance or repair work
not described in your instruction manual. Have such work performed by your
STIHL servicing dealer only.
Wear gloves when handling or
performing maintenance on blades.
Warning!
Use the specified spark plug, and make
sure it and the ignition lead are always
clean and in good condition. Always
press the spark plug boot snugly onto
the spark plug terminal of the proper
size. (Note: If the terminal has a detachable SAE adapter nut, it must be
securely attached.) A loose connection
between the spark plug and the ignition
wire connector in the boot may create
arcing that could ignite combustible
fumes and cause a fire.
Warning!
Never test the ignition system with the
spark plug boot removed from the spark
plug or with a removed spark plug, since
uncontained sparking may cause a fire.
Warning!
Do not operate your power tool if the
muffler is damaged, missing or modified. An improperly maintained muffler
will increase the risk of fire and hearing
loss. If your muffler was equipped with a
spark-arresting screen to reduce the
risk of fire, never operate your power
tool if the screen is missing or damaged.
Remember that the risk of forest fires is
greater in hot or dry weather.
Warning!
Never repair damaged cutting attachments by welding, straightening or
modifying the shape. This may cause
parts of the cutting attachment to come
off and result in serious or fatal injuries.
Keep blades sharp. Tighten all nuts,
bolts and screws after each use.
Do not clean your machine with a
pressure washer. The solid jet of water
may damage parts of the machine.
Store the power tool in a dry and high or
locked location out of reach of children.
Before storing for longer than a few
days, always empty the fuel tank. See
chapter "Storing the Machine" in the
instruction manual.
FS 460 C-M, FS 460 C-M L
15
English
Approved Combinations of Cutting Attachment, Deflector, Limit Stop and Harness
Cutting attachment Deflector, limit stop Harness
1
2
3
13
54
14
6
7
8
15
9
10
17
16
11
12
681BA172 KN
16
FS 460 C-M, FS 460 C-M L
English
Permissible combinations
Choose the proper combination from the
table depending on the cutting
attachment!
For safety reasons only the
cutting attachments and deflectors
and/or limit stops within one line of
the table may be combined with
one another. Other combinations
are not permissible – risk of
accident!
Cutting attachments
Mowing heads
1 STIHL SuperCut 40-2
2 STIHL AutoCut 40-2
3 STIHL AutoCut 40-4
4 STIHL TrimCut 41-2
5 STIHL PolyCut 41-3
Metal cutting attachments
6 Grass cutting blade 230-4
7 Grass cutting blade 255-8
8 Brush knife 300-3
9 Circular saw blade 200 scratcher
tooth
10 Circular saw blade 200 chisel tooth
11 Circular saw blade 225 scratcher
tooth
12 Circular saw blade 225 chisel tooth
Circular saw blades of other, nonmetal materials must not be used.
Deflectors, limit stops
Deflectors
13 Deflector only for mowing heads
14 Deflector for the mowing tools
Items 6 to 8
Limit stops
15 Limit stop for circular saw blades
200
16 Limit stop for circular saw blades
225
Harnesses
17 Full harness must be used
Warning!
Based on the cutting attachment being
used:
Choose the proper deflector in order to
reduce the risk of injury from thrown
objects and contact with the cutting
attachment.
Make sure your unit is equipped with the
proper handle and harness in order to
reduce the risk of injury from loss of control and contact with the cutting
attachment.
Use grass cutting metal blades, brush
knifes and circular saw blades on this
unit only if equipped with a bike handle.
Do not use rigid polymer blades on this
unit.
Mounting the Bike Handle
Mounting the bike handle with
swiveling handle support
2
1
The machine is supplied with the clamp
moldings (1) mounted to the
handlebar (2).
Mounting the control handle
3
5
4
N Take out the screw (3) and remove
the nut (4) from the control
handle (5).
6BA018 KN
002BA352 KN
FS 460 C-M, FS 460 C-M L
17
English
9
5
6
10
2
8
7
2
5
4
3
8
N Use the spring (9) from the parts kit
supplied with the machine.
N Place the spring (9) in the lower
clamp molding (10).
A
6BA001 KN
N Line up the control handle (5)
relative to the handlebar (2): The
throttle trigger (6) must point toward
the gearbox and the clamp
screw (7) toward the engine.
6BA002 KN
N Holding the control handle (5) in
that position, push it on to the end of
the handlebar (2) and line up the
holes (8).
N Fit the nut (4) in the control
handle (5), insert the screw (3) and
tighten it down firmly.
Assembling the handle support
Assembly of the swivelling handle
support involves equipping the clamp
moldings with a spring and mounting
them on the handle support.
6BA019 KN
1
2
11
6BA020 KN
N Position the clamp moldings (1) with
handlebar (2) on the handle
support (11).
18
FS 460 C-M, FS 460 C-M L
English
7
2
N Raise the grip of the wing screw (7)
to the upright position.
N Turn the wing screw
counterclockwise as far as stop.
N Push the wing screw into the handle
support as far as stop and then
screw it down – but do not finally
tighten yet.
N Adjust the handlebar (2) so that
distance A is no more than 15 cm.
N Line up the handlebar at a right
angle to the drive tube.
N Turn the wing screw clockwise as
far as stop.
6BA003 KN
N Fold the grip of the wing screw down
so that it is flush.
Adjusting the handlebar
Opening the wing screw
N Raise the grip of the wing screw to
the upright position.
6BA005 KN
6BA006 KN
N Move the handlebar to the required
position.
Closing the wing screw
N Turn the wing screw clockwise as
6BA023 KN6BA004 KN
far as stop.
N Fold the grip of the wing screw down
so that it is flush.
6BA007 KN
6BA005 KN
6BA006 KN
FS 460 C-M, FS 460 C-M L
N Turn the wing screw
counterclockwise until the handle
support can be moved.
19
English
Swiveling the handlebar
Transport position
2
7
N Loosen the wing screw (7) and
unscrew it until the handlebar (2)
can be turned clockwise.
N Turn the handlebar 90° and then
swing the handles down.
N Tighten down the wing screw (7)
firmly.
Working position
N Reverse the sequence described
above to swing the handles up and
turn the handlebar
counterclockwise.
Mounting the Deflector
Using the proper deflector
1
Deflector (1) is approved only for
mowing heads, thus deflector (1)
must be attached before attaching
a mowing head.
6BA008 KN
2
Deflector (2) is approved only for
grass cutting blades, thus
deflector (2) must be attached
before attaching a grass cutting
blade.
3
4
Limit stop (3) is approved only for
circular saw blades, thus limit
stop (3) must be attached and
guard ring (4) replaced before
002BA401 KN
attaching a circular saw blade,
see "Mounting the cutting
attachment" / "Mounting circular
saw blades".
Mounting the deflector
Deflectors (1-3) are attached to the
gearbox in the same manner.
6
002BA402 KN
5
N Set the deflector on the gearbox (5),
N screw in and tighten the screws (6)
002BA433 KN
002BA434 KN
20
FS 460 C-M, FS 460 C-M L
English
Mounting the Cutting
Attachment
Preparing the machine
N Lay down the machine so that the
mount for the cutting attachment
faces upward
Attaching the thrust plate
2
1
3
4
N Push the thrust plate (1) and guard
washer (2) onto the shaft (3)
The machine is equipped at the factory
with a guard ring (4) for mowing tools.
The thrust plate (1) on the
gearbox is required for securing
all cutting attachments.
The guard washer (2) on the
gearbox is required for securing
all cutting attachments with the
exception of circular saw blades.
Mounting the cutting attachment
Use the appropriate deflector for
the cutting attachment – see
"Mounting the deflector".
Mounting the mowing heads
STIHL SuperCut, STIHL AutoCut,
STIHL TrimCut, STIHL PolyCut
002BA406 KN
N Use the guard ring for mowing tools
N Attach the deflector for mowing
heads
1
002BA407 KN
N Block the shaft
N Turn the mowing head
counterclockwise onto the shaft (1)
and tighten
Remove the tool used to block the
shaft.
Keep the information sheet for the
mowing head in a safe place.
Removing the mowing head
N Block the shaft
N Unscrew the mowing head
clockwise
Feeding out mowing line
A detailed description is contained in the
information sheet for the respective
mowing head.
SuperCut Mowing Head
Line is fed out automatically during
mowing and shortened to optimum
length by the blade on the deflector. Line
is fed out only if both ends of the line are
still at least 6 cm long.
AutoCut Mowing Head
N Hold the machine over an area of
lawn with the engine running
(mowing head must rotate)
N Tap the mowing head on the ground
– line is fed out automatically and
shortened to optimum length by the
blade on the deflector
Line is fed out only if both ends of the
line are still at least 2.5 cm long.
TrimCut Mowing Head
002BA408 KN
Always switch off the engine to
fed out mowing line by hand –
otherwise there is a risk of injury!
FS 460 C-M, FS 460 C-M L
21
English
N Pull up the spool housing – turn
counterclockwise – approx. 1/6 turn
– until it engages – and then allow it
to spring back
N Pull the ends of the line outward
Repeat operation as needed until both
ends of the line are approx. 13 cm long.
A rotary movement from one click to the
next releases approx. 4 cm of line.
PolyCut Mowing Head
Always switch off the engine to
load the mowing head by hand –
otherwise there is a risk of injury!
Proceed as described in the mowing
head information sheet.
Attaching grass cutting blades,
brush knives
With the grass cutting blade 255-8 (1),
the cutting edges must face clockwise.
Cutting attachments with 3 or
4 blades (2, 3) can face in any direction
– turn over these cutting attachments
periodically to avoid uneven wear.
N Use the guard ring for mowing tools
N Attach the deflector for metal
mowing tools
4
3
2
1
b
a
N Position cutting attachment (1)
The collar (a) must engage the
hole (b) in the cutting attachment!
N Fit the thrust washer (2) – curvature
faces upward
N Position thrust plate (3)
N Block the shaft
N Screw on the nut (4)
counterclockwise and tighten
Remove the tool used to block the
shaft.
002BA409 KN
22
Removing cutting attachments
N Block the shaft
N Unscrew the nut clockwise
A nut that moves too easily should
be replaced.
FS 460 C-M, FS 460 C-M L
English
Attaching circular saw blades
With circular saw blades, the cutting
edges must face clockwise.
For attaching circular saw blades, a limit
stop set is available as a special
accessory that contains a limit stop and
a guard ring for circular saw blades.
Change guard ring
3
4
5
N Remove guard washer (3) and
thrust plate (4)
N Remove guard ring (5) for mowing
tools
4
6
N Attach guard ring (6) for circular saw
681BA165 KN
blades
N Push thrust plate (4) onto the shaft
N Attach limit stop (7) for circular saw
blades
Do not use the guard washer (3)
for circular saw blades.
Mounting the cutting attachment
4
3
2
002BA424 KN
b
a
1
7
N Fit the thrust washer (2) – curvature
faces upward
N Position thrust plate (3)
A thrust plate (3) for sawing use, with
which the entire cutting depth of the
circular saw blade can be used, is
available as a special accessory.
002BA425 KN
N Block the shaft
N Screw on the nut (4)
counterclockwise and tighten
Remove the tool used to block the
shaft.
Removing cutting attachments
N Block the shaft
N Unscrew the nut clockwise
A nut that moves too easily should
be replaced.
FS 460 C-M, FS 460 C-M L
002BA423 KN
N Position cutting attachment (1)
The collar (a) must engage the
hole (b) in the cutting attachment!
23
English
Fuel
This engine is certified to operate on
unleaded gasoline and the STIHL twostroke engine oil at a mix ratio of 50:1.
Your engine requires a mixture of highquality gasoline and quality two-stroke
air cooled engine oil.
Use mid-grade unleaded gasoline with a
minimum octane rating of 89 (R+M/2). If
the octane rating of the mid-grade
gasoline in your area is lower, use
premium unleaded fuel.
Fuel with a lower octane rating may
increase engine temperatures. This, in
turn, increases the risk of piston seizure
and damage to the engine.
The chemical composition of the fuel is
also important. Some fuel additives not
only detrimentally affect elastomers
(carburetor diaphragms, oil seals, fuel
lines, etc.), but magnesium castings and
catalytic converters as well. This could
cause running problems or even
damage the engine. For this reason
STIHL recommends that you use only
high-quality unleaded gasoline!
Gasoline with an ethanol content of
more than 10% can cause running
problems and major damage in engines
with a manually adjustable carburetor
and should not be used in such engines.
Engines equipped with M-Tronic can be
run on gasoline with an ethanol content
of up to 25% (E25).
Use only STIHL two-stroke engine oil or
equivalent high-quality two-stroke
engine oils that are designed for use
only in air cooled two-cycle engines.
We recommend STIHL HP Ultra 2-Cycle
Engine Oil since it is specially
formulated for use in STIHL engines.
Do not use BIA or TCW rated (twostroke water cooled) mix oils or other
mix oils that state they are for use in both
water cooled and air cooled engines
(e.g., outboard motors, snowmobiles,
chain saws, mopeds, etc.).
Take care when handling gasoline.
Avoid direct contact with the skin and
avoid inhaling fuel vapor. When filling at
the pump, first remove the canister from
your vehicle and place the canister on
the ground before filling. Do not fill fuel
canisters that are sitting in or on a
vehicle.
The canister should be kept tightly
closed in order to avoid any moisture
getting into the mixture.
The machine‘s fuel tank and the canister
in which fuel mix is stored should be
cleaned as necessary.
Fuel mix ages
Only mix sufficient fuel for a few days
work, not to exceed 3 months of storage.
Store in approved fuel-canisters only.
When mixing, pour oil into the canister
first, and then add gasoline. Close the
canister and shake it vigorously by hand
to ensure proper mixing of the oil with
the fuel.
Gasoline
US gal. US fl.oz
12.6
2 1/2 6.4
5 12.8
Dispose of empty mixing-oil canisters
only at authorized disposal locations.
Oil (STIHL 50:1 or equivalent high-quality oils)
24
FS 460 C-M, FS 460 C-M L
English
Fueling
Preparations
When fueling on a slope, always
position the machine so that the
filler cap is facing uphill.
N On level ground, position the
machine so that the filler cap is
facing up.
N Before fueling, clean the filler cap
and the area around it to ensure that
no dirt falls into the tank.
Always thoroughly shake the mixture in
the canister before fueling your
machine.
In order to reduce the risk of burns
or other personal injury from
escaping gas vapor and fumes,
remove the fuel filler cap carefully
so as to allow any pressure buildup in the tank to release slowly.
Opening
N Raise the grip into an upright
position.
9926BA005 KN
N Turn the cap counterclockwise
(approx. 1/4 turn).
N Remove fuel filler cap.
Refueling
Take care not to spill fuel while fueling
and do not overfill the tank.
Closing
001BA218 KN
With grip in an upright position:
N Insert the cap – positioning marks
on the cap and the fuel tank opening
must line up.
N The cap should drop fully into the
opening in this position.
001BA219 KN
N While pressing the cap down, twist it
firmly clockwise as far as it will go
(approx. 1/4 turn).
001BA224 KN
N Fold down the grip.
001BA220 KN
001BA221 KN
001BA222 KN
FS 460 C-M, FS 460 C-M L
25
English
Checking for proper closure
N The lug on the grip must engage
entirely in the recess (arrow), and
the grip must lie completely flush
with the top of the cap.
N Grip the cap and check for
tightness.
N If the cap can be moved, it is not
properly installed.
Misalignment of the cap parts
N If the cap does not drop fully into the
opening when the positioning marks
line up and/or if the cap does not
tighten properly when twisted, the
base of the cap may be rotated out
of position vis-à-vis the top.
N Such misalignment can result from
handling, cleaning or an improper
attempt at tightening.
Left: Base of improperly aligned
001BA223 KN
cap (with open space)
Right: Base of cap correctly posi-
tioned for installation
N To correct a misalignment, turn the
001BA225 KN
cap (with the grip up) until it drops
fully into the tank opening.
N Twist the cap counterclockwise as
far as it will go (approx. 1/4 turn) –
this will twist the base of the cap into
the correct position.
N Twist the cap clockwise, closing it
normally – see the sections
"Closing" and "Checking for proper
closure."
N If your cap still does not tighten
properly, it may be damaged or
broken; immediately stop use of the
unit and take it to your authorized
STIHL dealer for repair.
Fitting the Full Harness
Fitting the full harness is described in
detail in the instruction sheet supplied.
001BA227 KN
1
2
3
001BA226 KN
N Put on the full harness (1).
N Adjust the length of the strap so that
the carabiner (2) is about a hand’s
width below your right hip.
N Attach the spring hook to the
machine's perforated strip (3).
Find the right attachment point for the
cutting attachment you are using – see
"Balancing the Brushcutter".
002BA411 KN
26
FS 460 C-M, FS 460 C-M L
English
Balancing the
Trimmer/Brushcutter
The machine will balance differently
depending on the cutting attachment
mounted.
N Let the machine swing on the
harness until it stops moving –
change the connection point if
necessary
Hanging positions
Mowing heads, grass cutting blades and
brush knives should rest lightly on the
ground.
Putting down the machine in an
emergency
As soon as it becomes apparent
that a dangerous situation is
developing, the machine must be
put down quickly. Practice setting
down the machine quickly. In
order to avoid damage, when
practicing, do not throw the
machine on the ground.
6BA009 KN
Starting / Stopping the
Engine
Controls
3
2
1
002BA392 KN
1 Throttle trigger lockout
2 Throttle trigger
3 Stop switch with Run and Stop
positions. Push the stop switch (h)
to switch off the ignition.
Circular saw blades should "hover"
approx. 8 in. (20 cm) above the ground.
FS 460 C-M, FS 460 C-M L
6BA010 KN
Function of stop switch and ignition
system
The stop switch is normally in the Run
position: Ignition is on in this position –
the engine is ready to start and may be
started. The ignition is switched off when
the stop switch is depressed. It is
automatically switched on again after
the engine comes to a standstill.
27
English
Starting the Engine
4
N Press the fuel pump bulb (4) at least
five times – even if the bulb is
already filled with fuel.
5
5
N Press in the outer edge (arrows) of
the choke knob (5) and then turn it
to } .
Starting
the cutting attachment is not
touching the ground of any other
obstacles.
N Make sure you have a firm footing –
either standing, stooping or
kneeling.
N Hold the unit firmly on the ground
with your left hand and press down
– do not touch the throttle trigger or
9926BA006 KN
lockout lever.
Do not stand or kneel on the drive
tube.
1BA001 KN
N Hold the starter grip with your right
hand.
Alternative method of starting:
Engine warm and the machine hanging
from the harness.
N Hold the machine firmly with your
right hand on the drive tube, handle
support or handlebar.
N With the machine behind you, press
it against the left side of your body.
N Hold the starter grip with your left
hand.
N Pull the starter grip steadily.
Do not pull out the starter rope all
the way – it might otherwise
6BA012 KN
break.
N Do not let the starter grip snap back.
Guide it slowly back into the housing
so that the starter rope can rewind
properly.
N Continue cranking until the engine
runs.
As soon as the engine runs
6BA013 KN
N Place the unit on the ground: It must
rest securely on the engine's guard
plate and the deflector. Check that
28
6BA011 KN
6BA014 KN
N Press down the throttle trigger
interlock and open the throttle – the
choke lever moves to the run
FS 460 C-M, FS 460 C-M L
Loading...