Stiga VILLA 85 M User Manual

85 M

DEUTSCH

D

8211-3502-01

A

1.

5.

B

2.

6.

3.

4.

7.

8.

2

9.

10.

Z

X

11.

Denna produkt, eller delar därav, omfattas av följande
mönsterskydd:
This product, or part of it, is covered by the following
design registration:

Sverige/Sweden 62 435

V

Y

W

3

GB

ENGLISH

SYMBOLS

The following symbols are displayed on the ma­chine in order to remind you about the safety pre­cautions and attention necessary when using the
machine.

The symbols mean:

Warning!
Read the instruction book and safety man­ual before using the machine.

ASSEMBLY

MOWER DECK

1. Remove both mounting bolts D on the base ma­chine (fig 3).

2. Insert both spacer sleeves E in the mower deck's
arms (fig 4). The spacer sleeves are supplied in a
plastic bag.

3. Bolt the mower deck to the base machine.

Warning!
Do not put hands or feet underthe cover of
the machine when it is running.

Warning!
Beware of objects being flung out. Keep
spectators away.

Warning!
Beforestartingany repairwork,removethe
spark plug cable from the spark plug.

INTRODUCTION

The power outlet's tension roller and tension arm's
spring on the base machine are available in two ver­sions (figs 1 and 2).

NOTE! To be able to fit this mower deck ("Multi­clip" mod. 85M) version B is required.

4. Pull the v-belt onto the mower deck's pulley.
(This is carried out easier if the height adjustment
lever is in position "5").

5. Make sure that the tension roller J is on the out-
side of the v-belt (figs 2 and 5).

6. Hook the spring into the bracket G (figs 2 and 5).

7. Screw the guard H in position using three screws
(fig 6). The screws are supplied in the plastic bag.

8. Hook the chain I and lifting spring F in the attach­ment's lift arm (fig 6).

SETTING

For the mower deck to mow evenly and cleanly it
needs to be adjusted correctly:

1. Make sure the tyre pressure is correct:
Front: 0.4 bar (6 psi).
Rear: 1.2 bar (17 psi).

2. Place the machine on a flat surface. Loosen the
screws K (fig 7).

VERSION A:
(Standard on models made between 1982 - 83).

If the base machine is fitted with version A a sepa­rate assembly set is required to be able to fit the
mower deck.

Assembly set, art. No.: 13-1967-11.
The set contains a v-belt, tension roller, spring, as-

sembly components and assembly instructions.
N.B. Older base machines can, however, be fitted

with version B ifthey have previouslybeen adapted
for use with a "Multiclip" mower deck.

VERSION B:
(Standard on machines made from 1994 - ).

The mower deck can be fitted directly.

4

3. Adjust the mower deck so that the casing's front
and rear edges are the same height from the floor.

4. Tighten the screws.

USE

MOWING HEIGHT

Themower deck has 17fixed mowing heights,from
30 mm to 80 mm.

N.B. The stated mowing heights apply when the
machine is standing on firm ground.

MOWING ADVICE

For the best "Multiclip" effect follow this advice:

- mow regularly.

- use full throttle on the engine.

ENGLISH

GB

- keep the underside of the mower deck clean.

- use sharp blades.

- do not mow wet grass.

- mow twice (using different mowing heights)
if the grass is long.

MAINTENANCE

Noserviceactionmustbetakenonthe
mower deck unless:

- the engine has bee n stopped.

- the ignition key has been removed.

- the spark plug cap has been removed
from the spark plug.

- the parking brake is engaged.

- the mow er deck is disengaged.

CLEANING

After use, rinse off the underside of the mower
deck using a garden hose.

If grass cuttings have dried on to the attachment,
dismantlethe mowerdeck and scrape clean the un­derside.

If necessary touch-up the underside using a suita­ble paint to prevent corrosion.

CHANGING THE DRIVE BELT

1. Remove the mower deck from the base machine.

chine.

8. Now refit the mower deck on the base machine.

CHANGING BLADES

Use protective gloves to prevent cuts
when changing blades/blade ti ps.

Make sure the blades are always sharp. This gives
the best mowing results.

Always check the blade(s) after an impact. If the
blade system has been damaged the defective parts
must be changed.

Always use original spare parts. Using
non-original spare parts can result in
the risk of damage even if they fit in the
machine.

The cutting system consists oftwo blade bars, each
with two interchangeable blade tips Y (fig 11).
Both blade tips should be replaced at the same time
to avoid any imbalance.

Fit the new blade tips. Tighten the screws V and W
fully. Tightening torque: V - 9.8 Nm, W - 24 N m.

And heavy impactcan result in the blade tip being
folded aside. Loosen the locking nut X and turn the
blade tip back to its correct position. Mount a new
shear bolt V. Tighten the lock nuts X and Z.

2. Remove the transmission casing.

3. Loosen the tension arm L (fig 8).

4. Loosen the right hand bearing box's fixing bolts

M (fig 9).

5. Fit the new drive belt.

Thenewdrivebeltmustbefittedsothat
the blades are square (90°) to each oth­er. See figure 10. If you fit the drive belt
incorrectly the blades will hit each oth­er resulting in the blade s being dam­aged.

6. The belt is tensioned by pushing the tension arm

L forwards and then securing in position.

7. Tighten the bearing box's fixing bolts M.

When the drive belt is fitted, check, by
turningthemowerdeckoverandturn­ing the blades, that it has been fitted
correctly. NOTE! The mower deck
should be dismantled from the base ma-

5