Stiga T8730, ST30000 Owner's Manual
TABLE TENNIS TABLE
MODEL NO.
T8730 (ST3000)
OWNER'S MANUAL
1. Read this manual carefully before starting assembly.
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. Do not tighten hardware until instructed to do so.
holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.
4. Tools required for assembly:
Note: Adjustable wrenches can be substituted for wrenches.
Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches.
Read each step completely before beginning
If hardware is tightened too soon, mounting
Please Do Not Return This Product To The Store!
Contact Escalade®Sports customer service department at:
Phone: 1-800-467-1245 Toll Free !
Fax: 1-866-873-3533 Toll Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE
Escalade® Sports productsmay bemanufactured and/or licensed underthe followingpatents.
6120397, 5816957, 5769744, 5119741,4911085, 4717157,D460140, D420563
Additional patents maybe pending.One or more ofthe listedpatents and/or pending patentsmay coverspecific product.
®
SPORTS PRODUCT INFORMATION
2L-5027-02
ÓÓ
2008 Escalade Sports
ÒÒ
1/4"
Plastic
Washer
Washer
Plastic
3/8"
28
30
31
32
33
34
35
37
1/4-20 X 3 1/4 Carriage Bolt
1/4-20
Wing
Nut
#8 X 9/16
SMS
#8-32X11/4
Sheet Metal Screw
3/8" Long Spacer
3/4" Long Spacer
38
39
36
1/4-20 X 2 3/4 Hex Head Bolt
29
HARDWARE IDENTIFIER
2
3/8-16
Nyloc
Locknut
1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
1. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#7) as shown in figure 1. Turn Caster
Beams as shown and attach board with four
Carriage Bolts (#31) and four Wing Nuts (#32).
Tighten Thumb Screws securely.
Note: Support Plate (#43)
must be on inside of Caster
Rail (#7) as shown.
43
31
15
Figure 1
7
32
2.
Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#7) as shown in Figure 2.
a) Bolts (
Loosen #13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43)
and Caster Beam (#7) as shown in the Top View and Figure 2.
Slide one Hex Bolt (#27) through , followed by one Plastic Washer (#39), Strut
b)
Tube (#17), one Plastic Washer (#39), pass through Caster Beam (#7), one Spacer (#36), one
Linkage (#16), and Lock Nut (#28).
Repeat on other end of Caster Beam (#7) and on second Caster Beam.
c)
Tighten (#13) and Nuts (#28) securely.
d)
Tighten Nuts (#28) on Bolts (#27) securely.
e)
Bolts
Support Plate (#43)
31
7
32
NOTE:
tubes must be turned as
Tighten nuts so that end of Bolt (#27) in even with the edge of nut.
Note: Linkages & Strut
shown or table will not
operate correctly.
Figure 2
28
Top View
27
17
43
28
16
7
28
43
7
36
13
27
39
12
13
7
36
28
17
16
3
3. Rotate U-support (#21) that is on bottom of Table
Top Assembly until you see the screw holes in the
slots of U-clips (#22). Slide U-support (#21) side
to side if necessary to see holes. See figure 3.
4. Insert Screw (#35) through slot in U-clip (#22)
and into U-support (#21). See figure 3. Thread
screw all the way into U-support until it touches the
back of the tube. There should be about 3/8”of
screw (#35) left sticking out. Repeat for other
screw as shown in figure 3.
5. Repeat steps 3 and 4 on other table top assembly.
35
Note: Slide U-Support back and forth
until you see the hole if necessary.
22
21
35
21
U-Support
Table Top
Assembly
Figure 3
Table Top
Assembly
With at least 2 adults,
slide Table Top Assembly
onto Strut Tubes
Strut Tube
17
AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY! WHEN
ASSEMBLING TOPS TO BASE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS, USUPPORT, LINKAGE, OR HINGES. THESE PARTS
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ASSEMBLE
AS SHOWN WITH LEGS FULLY CLOSED AND
21
U-Support
17
Strut Tube
TOPS IN A VERTICAL POSITION. DO NOT OPEN
LEGS AND TRY TO ASSEMBLE. TABLE TOPS ARE
HEAVY - DO NO T ATTEMPT TO ASSEMBLE
ALONE!
6. Attach Table Top Assembly to Base Assembly (that
PIVOT STRUT
TUBES UP
you put together in steps 1 & 2), as shown in figure
4. Pivot Strut Tubes (#17) up as shown; then, with
at least one adult on each side of Table Top, lift top
and align ends of U-support tube (#21) with tops
of Strut Tubes (#17) on Caster Beams (#7) as
shown in figure 4. Slide tubes together.
7
7
Figure 4
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
4
7. Screw U-support tube (#21) to Strut Tubes (#17) with
two Screws (#33) as shown in figure 5. Align holes in
U-support with holes in Strut Tubes and thread screw
(#33) into hole in Strut Tube (#17) Tighten screws all
the way but be careful not to over tighten. You could
strip threads on screws if you over tighten.
8.
Attach Hinges (#18) to Strut Tubes (#17) as shown in
figure 5. With hinge positioned as shown, align hole in
hinge with hole in Strut Tube and attach with ¼” Screw
(#30), Plastic Washer (#38) and Locknut (#34).
Plastic Washer
(#38) goes between Strut Tube and
Hinge. Tighten nut securely. Repeat for other Hinge.
CAUTION: Hinges must be positioned exactly
as shown or table will not operate correctly and
could be damaged.
DO NOT OPEN THE TABLE TO PLAYING POSITION UNTIL
BOTH TOPS ARE INSTALLED! DO NOT LEAVE TABLE
STANDING UNATTENDED. IT COULD BE KNOCKED OVER
CAUSING SERIOUS BODILY INJURY OR PROPERTY DAMAGE.
ATTENTION: If hinge is positioned as
shown below (Detail A), flip the hinge as
shown in Detail B.
Detail A
9. Attach Linkages (#16) to Leg (#19) as shown in
figure 5. Pivot one Linkage (#16) up and pivot Leg
out from top and align hole in Linkage with hole in
Leg (#19). Attach Linkage (#16) to Leg (#19)
using Hex Head Bolt (#29), Spacer (#37) and
Locknut (#34). Spacer (#37) goes between
Linkage and Leg. Attach other Linkage to Leg the
same way. Tighten nuts securely.
10.
Attach Corner Protector (#40) to table corners.
Push snap tabs on Corner Protector into holes in
Be sure that tabs are aligned with
rails.
holes before pushing
. You could break tabs if
they are not aligned correctly.
11. With at least two adults, repeat steps 6
through 10 for other table top assembly..
Figure 5
19
40
18
Incorrect position
of hinge
CAUTION: Hinges must be positioned
exactly as shown or table will not operate
correctly and could be damaged.
Detail B
30
18
Correct position
of hinge
16
17
34
38
17
29
16
30
17
37
34
33
21
17
34
29
37
Spacer goes between
Linkage Arm (#16) and
Leg (#19)
16
33
30
38
Plastic Washer goes
between Strut Tube
(#17) and Hinge (#18)
18
Hinge Assembly
34
38
18
Hinge Assembly
5
Loading...