STIEBEL ELTRON SBP 100, WPKI-H E, SBP-HF, WPKI-P E, WPKI-W E Operation And Installation

...

BEDIENUNG UND INSTALLATION OPERATION AND INSTALLATION UTILISATION ET INSTALLATION OBSLUHA A INSTALACE

OBSŁUGA I INSTALACJA

Pufferspeicher mit Heizansch und Wärmepumpen-Kompaktinstallationen| Buffer cylinder with anged immersion heater and compact heat pump installations| Ballon tampon avec résistance électrique à bride et kit hydraulique pompe à chaleur| Akumulační zásobník s topnou přírubou a kompaktními instalacemi tepelného čerpadla| Zbiornik buforowy z kołnierzem grzejnym oraz instalacjami kompaktowymi dla pomp ciepła

» SBP 100 » SBP-HF » WPKI-H E » WPKI-P E

» WPKI-W E » WPKI-V

°C

100

120

°C

100

120

bar

65°C

CONTENTS | SPECIAL INFORMATION

SPECIAL INFORMATION

OPERATION

1. General information �� 23

1.1 Safety instructions �� 23

1.2 Other symbols in this documentation �� 23

1.3 Units of measurement �� 23

2. Safety �� 23

2.1 Intended use �� 23

2.2 General safety instructions ��24

2.3 Test symbols �� 24

3. Appliance description �� 24

4. Immersion heater accessory: Settings �� 24

5. Cleaning, care and maintenance �� 24

6. Troubleshooting �� 24

7. Safety �� 25

7.1 General safety instructions �� 25

7.2 Instructions, standards and regulations �� 25

8. Appliance description �� 25

8.1 Standard delivery �� 25

8.2 Accessories �� 25

9. Preparations �� 25

9.1 Installation site �� 25

9.2 Fitting the wall mounting bracket/ mounting panel �� 25

9.3 Connector with sensor sleeve �� 26

9.4 Fitting the quick-action air vent valve �� 26

10. Installation �� 26

10.1 Immersion heater accessory �� 26

10.2 Appliance installation �� 28

10.3 Electrical connection �� 28

10.4 Compact heat pump installation accessory �� 28

10.5 Heating water connection �� 34

11. Commissioning �� 34

11.1 Initial start-up �� 34

11.2 Recommissioning �� 34

12. Shutdown �� 34

13. Troubleshooting �� 35

14. Maintenance �� 35

14.1 Checking the safety valve ��35

14.2 Draining the appliance �� 35

15. Speciﬁcation �� 36

15.1 Dimensions and connections �� 36

15.2 Wiring diagrams and terminals �� 37

15.3 Circulation pump rating curves �� 38

15.4 Fault conditions �� 38

15.5 Details on energy consumption �� 39

15.6 Data tables �� 39

SPECIAL INFORMATION

- The appliance may be used by children aged8 and older and persons with reduced physical, sensory or mental capabilities or a lack of experience and know-how, provided that they are supervised or they have been instructed on how to use the appliance safely and have understood the resulting risks. Children must never play with the appliance. Children must never clean the appliance or perform user maintenance unless they are supervised.

- Immersion heater accessory: The connection to the power supply must be in the form of a permanent connection. The appliance must be able to be separated from the power supply by an isolator that disconnects all poles with at least 3mm contact separation.

- Secure the appliance as described in chapter "Installation/ Preparations".

- Observe the maximum permissible pressure (see chapter "Installation/ Speciﬁcation/ Data table").

- Regularly activate the safety valve to prevent it from becoming blocked.

- Drain the appliance as described in chapter "Installation/ Maintenance/ Draining the appliance".

- Install a type-tested safety valve.

- Fit the discharge pipe of the safety valve with a constant downward slope and in a room free from the risk of frost.

- The safety valve discharge aperture must remain open to the atmosphere.

GUARANTEE

ENVIRONMENT AND RECYCLING

22 | SBP 100 www.stiebel-eltron.com

OPERATION

General information

OPERATION

1. General information

The chapters "Special Information" and "Operation" are intended for both the user and qualiﬁed contractors.

The chapter "Installation" is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the appliance and retain them for future reference. Pass on the instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

KEYWORD Type of risk

Here, possible consequences are listed that may result from failure to observe the safety instructions.

 Steps to prevent the risk are listed.

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the adjacent symbol.

 Read these texts carefully.

Symbol Meaning

 This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

Material losses (appliance damage, consequential losses and environmental pollution)

Appliance disposal

1.3 Units of measurement

Note

All measurements are given in mm unless stated otherwise.

2. Safety

ENGLISH

1.1.2 Symbols, type of risk

Symbol Type of risk

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

WARNING Failure to observe this information may result in serious

CAUTION Failure to observe this information may result in non-seri-

Injury

Electrocution

Burns (burns, scalding)

injury or death.

ous or minor injury.

2.1 Intended use

The appliance acts primarily as a buffer cylinder for heat pumps to function as a hydraulic separator of the ﬂow between the heat pump circuit and the heating circuit.

This appliance is intended for domestic use. It can be used safely by untrained persons. The appliance can also be used in a non-domestic environment, e.g. in a small business, as long as it is used in the same way.

Observation of these instructions and of instructions for any accessories and other system components is also part of the correct use of this appliance.

Any other use beyond that described shall be deemed inappropriate. Using the appliance for heating ﬂuids other than water or for water supplemented with chemicals, such as brine, is also deemed inappropriate.

www.stiebel-eltron.com SBP 100| 23

OPERATION

65°C

Appliance description

2.2 General safety instructions

WARNING Burns There is a risk of scalding at outlet temperatures in excess of 43 °C.

WARNING Injury

The appliance may be used by children aged 8 and older and persons with reduced physical, sensory or mental capabilities or a lack of experience and know-how, provided that they are supervised or they have been instructed on how to use the appliance safely and have understood the resulting risks. Children must never play with the appliance. Children must never clean the appliance or perform user maintenance unless they are supervised.

With immersion heater accessory:

Material losses

The user must protect the water pipes and safety valve from frost.

2.3 Test symbols

See type plate on the appliance.

3. Appliance description

This pressurised appliance is equipped with a quick-action air vent valve and a cleaning aperture with drain & ﬁll valve.

An immersion heater can be retroﬁtted.

4. Immersion heater accessory: Settings

The temperature is variably adjustable.

1 ON/OFF indicator 2 Frost protection 65°C maximum temperature setting

Depending on the system, the actual temperatures may vary from the set value.

ON/OFF indicator

The ON/OFF indicator illuminates when water is being heated.

5. Cleaning, care and maintenance

 Have the function of the safety assembly and electrical safe-

ty of the ﬁtted accessories regularly checked by a qualiﬁed contractor.

 Never use abrasive or corrosive cleaning agents. A damp

cloth is sufﬁcient for cleaning the appliance.

 Regularly activate the safety valve to prevent it from becom-

ing blocked.

26�03�01�0343

Frost protection with immersion heater accessory

If the power supply is guaranteed, the appliance is also protected from frost on the temperature setting "cold". The appliance switches on in good time and heats the water. The appliance does not protect the water pipes and safety valve from frost.

6. Troubleshooting

Call your qualiﬁed contractor. To facilitate and speed up your enquiry, please provide the serial

number from the type plate (000000-0000-000000):

000000-0000-000000

Made in Germany

D0000048097

24 | SBP 100 www.stiebel-eltron.com

INSTALLATION

756

Safety

INSTALLATION

7. Safety

Only a qualiﬁed contractor should carry out installation, commissioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational reliability only if original accessories and spare parts intended for the appliance are used.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations and instructions.

8. Appliance description

8.1 Standard delivery

The following are delivered with the appliance:

- 2 wall mounting brackets

- Mounting panel

- Quick-action air vent valve G 1/2

- Connector with sensor well for return temperature sensor

9. Preparations

9.1 Installation site

The appliance is designed for installation on a solid wall. Ensure the wall offers adequate load bearing capacity.

Always install the appliance vertically in a room free from the risk of frost. The room must be at least 2200mm high.

9.2 Fitting the wall mounting bracket/ mounting panel

The appliance can be mounted on the wall mounting bracket or, with clearance to the wall, to the mounting panel.

Observe the minimum clearances to the heat pump.

880

282

350

≥2200

≥100

280

ENGLISH

8.2 Accessories

8.2.1 Required accessories

Various safety assemblies are available for sealed unvented (pressurised) operation, depending on the supply pressure. These type-tested safety assemblies protect the appliance against unacceptable excess pressure.

8.2.2 Further accessories

Booster heater

The ﬂanged immersion heater is intended for retroﬁtting.

Compact heat pump installations

Compact heat pump installations are heat pump system components that have been especially designed for the SBP100 cylinder.

Circulation pumps are available as required accessories for compact heat pump installations which are approved for direct connection to the heat pump manager:

- UP 25/7.0 E, part number 232942

- UP 25/7.5 E, part number 232943

45°

510

1 Mounting panel 2 Heat pump

 Mark out the holes to be drilled on the wall (see chapter

"Speciﬁcation/ Dimensions and connections").

562

D0000048224

www.stiebel-eltron.com SBP 100| 25

INSTALLATION

Installation

1 Mounting panel

 Drill the holes and secure the wall mounting bracket or

mounting panel with screws and rawl plugs. Select ﬁxing materials in accordance with the wall construction/condition.

9.3 Connector with sensor sleeve

 Screw the connector with sensor sleeve for the return

temperature sensor into the "charging station return opt." connection (see chapter "Speciﬁcation/ Dimensions and connections").

10.1.2 Fitting the immersion heater

Note

If you would like to retroﬁt the immersion heater, please observe the following:

 Drain the cylinder (see chapter "Maintenance/

Draining the appliance")

 Release the pipe ﬁttings and remove the appliance

from the wall.

D0000048229

 Remove the lower cover.

26�03�01�0342

9.4 Fitting the quick-action air vent valve

Fit the quick-action air vent valve provided to the "ventilation" connection (see chapter "Speciﬁcation/ Dimensions and connections").

10. Installation

10.1 Immersion heater accessory

10.1.1 Standard delivery

- Type plate

- Adhesive fascia

- Fitting PG 11

- Wiring diagram label

- Seal ring

- Safety valve

3 4

26�03�01�0341

1 Quick-action air vent valve 2 Booster heater 3 Seal ring 4 Drain valve

 Remove the drain valve.  Remove the ﬂange plate. To do this, undo the 10 screws.  Fit the immersion heater with the seal ring supplied.  Connect the insulating plate.

26 | SBP 100 www.stiebel-eltron.com

+ 14 hidden pages

STIEBEL ELTRON SBP 100, WPKI-H E, SBP-HF, WPKI-P E, WPKI-W E Operation And Installation

Specifications and Main Features

Frequently Asked Questions

User Manual