STIEBEL ELTRON MINI 2.5-1, MINI 3-1, MINI 3.5-1, MINI 4-2, MINI 6-2 Operation And Installation

...

OPERATION AND INSTALLATION FUNCIONAMIENTO E INS TAL AC IÓN MODE D’EMPLOI ET INSTALLATION

TANKLESS ELECTRIC WATER HEATER WITH ELECTROMECHANICAL FLOW SWITCH CALENTADOR ELÉCTRICO DE AGUA SIN TANQUE CON SENSOR ELECTROMECÁNICO DE FLUJO CHAUFFE-EAU ÉLECTRIQUE SANS RÉSERVOIR AVEC CONTACTEUR DEBITMETRIQUE ÉLECTROMÉCANIQUE

» MINI™ 2-1 » MINI™ 2.5-1 » MINI™ 3-1 » MINI™ 3.5-1 » MINI™ 4-2 » MINI™ 6-2

Conforms to ANSI/UL Std. 499 Certiﬁ ed to CAN/CSA Std. E335-1 & E335-2-35

Conforme a ANSI/UL Std. 499 Certiﬁ cación con CAN/CSA Std. E335-1 & E335-2-35

Conforme à la norme ANSI/UL Std. 499 Certiﬁ é à la norme CAN/CSA Std. E335-1 & E335-2-35

Tested and certiﬁ ed by WQA to NSF/ANSI372 for lead free compliance.

Probado y certiﬁ cado por WQA NSF/ANSI 372 para el cumplimiento de las regulaciones sin plomo.

Testé et certiﬁ é par WQA à la NSF/ANSI 372 pour une utilisation sans plomb.

CONTENTS | OPERATION

poppo

pppo

ppwer

GENERAL INFORMATION

1. General Information __________________________________________ 2

1.1 Symbol key ___________________________________________________________ 2

2. Safety precautions ____________________________________________ 3

3. Register your product ________________________________________3

4. Temperature increase above ambient water temperature 4

5. Technical drawings ___________________________________________ 4

6. Overview ______________________________________________________ 6

6.1 General Description ________________________________________________ 6

6.2 Important information before supplying power to unit_____ 6

6.3 Hot water output at max rated voltage _________________________ 6

6.4 Incorrect use _________________________________________________________ 7

6.5 First steps to be taken in the event of malfunction __________7

6.6 Maintenance and care _____________________________________________ 7

7. Installation instructions ______________________________________ 7

7.1 Mounting the unit __________________________________________________ 7

7.2 Plumbing connections _____________________________________________ 7

7.3 Electrical connection _______________________________________________ 8

8. Initial start-up ________________________________________________8

9. Water heater hand over ______________________________________ 8

10. Normal maintenance _________________________________________ 8

11. Technical data _________________________________________________ 9

12. Troubleshooting _______________________________________________ 9

13. Spare parts ___________________________________________________10

14. Warranty _____________________________________________________11

THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT



YOU TO POTENTIAL PERSONAL INJURY HAZARD. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY OR DEATH.

The chapter Operation is intended for homeowners, heating contractors, plumbers and electricians.

The chapter Installation is intended for heating contractors, plumbers and electricians only.

1.1 Symbol key

1.1.1 Layout of safety information

DANGER Electric shock

Before any work on the appliance, disconnect all poles from the power supply.

1 Symbol (see 1.1.2 “Symbols”, below) 2 Keyword (see 1.1.3 “Keywords”, below) 3 Description (see 1.1.2 “Symbols”, below)

4 Information text

1.1.2 Symbols

1. General Information

Read this entire manual. Failure to follow all the guides, instructions and rules could cause personal injury or property damage. Improper installation, adjustment, alteration, service and use of this unit can result in serious injury.

T his u ni t mu s t b e in s t al l ed b y a l ic ens e d el e c tr i ci an a n d p l um b er . T h e installation must comply with all national, state and local plumbing and electric codes. Proper installation is the responsibility of the installer. Failure to comply with the installation and operating instructions or improper use voids the warranty.

Save these instructions for future reference. Installer should leave these instructions with the consumer.

If you have any questions regarding the installation, use or operation of this water heater, or if you need any additional installation manuals, please call our technical service line at 800582-8423 (USA and Canada only). If you are calling from outside the USA or Canada, please call USA 413-247-3380 and we will refer you to a qualiﬁ ed Stiebel Eltron service representative in your area.

Symbol Description

Injury

Electrocution

Burns or scalding

Other situations

1.1.3 Keywords

KEYWORD

DANGER The keyword DANGER indicates information that

must be observed, otherwise serious injury or death will result.

WARNING The keyword WARNING indicates information that

must be observed, otherwise serious injury or death may result.

CAUTION The keyword CAUTION indicates information that

must be observed, otherwise relatively serious or light injuries may result.

2 | MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS WWW.STIEBEL-ELTRON-USA.COM

GENERAL INFORMATION | OPERATION

SAFETY PRECAUTIONS

2. Safety precautions

PLEASE READ AND FOLLOW THESE INSTRUCTIONS.



FAILURE TO FOLLOW THESE INSTRUCTIONS COULD

RESULT IN SERIOUS BODILY INJURY OR DEATH.

THE UNIT MUST BE INSTALLED BY A LICENSED ELECTRICIAN AND PLUMBER. THE INSTALLATION MUST COMPLY WITH ALL NATIONAL, STATE AND LOCAL PLUMBING AND ELECTRIC CODES.

SERVICE OF THE UNIT MUST BE PERFORMED BY QUALIFIED SERVICE TECHNICIANS.

BEFORE PROCEEDING WITH ANY INSTALLATION,



ADJUSTMENT, ALTERATION, OR SERVICE OF THIS UNIT ALL CIRCUIT BREAKERS AND DISCONNECT SWITCHES SERVICING THE UNIT MUST BE TURNED OFF. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

DANGER: NEVER REMOVE THE UNIT'S COVER UNLESS



THE ELECTRICITY SERVICING THE UNIT IS TURNED OFF. FAILURE TO DO SO COULD RESULT IN PERSONAL INJURY OR DEATH.

WARNING: THE UNIT MUST BE PROPERLY GROUNDED.



FAILURE TO ELECTRICALLY GROUND THE PRODUCT COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

DANGER: WATER TEMPERATURES OVER 125°F CAN



CAUSE SEVERE BURNS INSTANTLY OR DEATH FROM SCALDING. A HOT WATER SCALDING POTENTIAL EXISTS IF THE THERMOSTAT ON THE UNIT IS SET TOO HIGH. HOUSEHOLDS WITH SMALL CHILDREN, DISABLED OR ELDERLY PERSONS MAY REQUIRE THAT THE THERMOSTAT BE SET AT 120°F OR LOWER TO PREVENT POSSIBLE INJURY FROM HOT WATER.

3. Register your product

YOU MUST REGISTER THIS PRODUCT WITHIN 90 DAYS OF



PURCHASE ON OUR WEB SITE IN ORDER TO ACTIVATE THE

STANDARD WARRANTY OR TO BE ELIGIBLE FOR THE EXTENDED WARRANTY. GO TO OUR WEB SITE AT WWW.STIEBEL-ELTRON-USA. COM AND CLICK ON REGISTER YOUR PRODUCT.

Before beginning the registration process, we suggest that you gather the necessary information which will be as follows:

Type, Example: Mini 3-1 (from the white label that is on the right side of the unit)

Number listed after "Nr." Place of Purchase Purchase Date First & Last Name Email address Physical Address Phone Number

IF YOU HAVE ANY QUESTIONS CONCERNING THE REGISTRATION PROCESS OR WARRANTY OPTIONS, PLEASE CONTACT STIEBEL ELTRON USA DIRECTLY AT (800)-582-8423.

Limited liability warranty:

Stiebel Eltron, Inc. is not liable for damages to the unit, damage to personal property, bodily injury, or loss of life due to the following conditions:

- Non-observance of these instructions

- Incorrect use (heating any other liquid than water)

- Installation of the appliance by unqualiﬁ ed personnel

- Unauthorized modiﬁ cations

- Technical modiﬁ cations

- Use of unauthorized spare parts

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS | 3

THE THREE YEAR WARRANTY COVERS ALL PARTS BUT DOES NOT COVER DAMAGE TO THE UNIT DUE TO HARD WATER (FOR THE COMPLETE WARRANTY SEE SECTION 14, “WARRANTY”, PG. 11). IF YOU KNOW OR SUSPECT THAT THE WATER IN YOUR AREA IS HARD (HAS A HIGH MINERAL CONTENT), IT IS NECESSARY TO INSTALL A WATER SOFTENING DEVICE TO AVOID DAMAGE TO THE Mini™ UNIT.

GENERAL INFORMATION | OPERATION

TEMPERATURE INCREASE ABOVE AMBIENT WATER TEMPERATURE

4. Temperature increase above ambient water temperature

[ °F ]

Type kW GPM

0.32 0.42 0.48 0.5 0.69 0.85 1.06 1.14

Mini 2-1* 1.8 39 – – – – – – –

Mini 2.5-1

Mini 3-1

Mini 3.5-1

Mini 4-2

Mini 6-2

Type kW l/min

1.2 1.6 1.8 2.0 2.6 3.2 4.0 4.3

Mini 2-1* 1.8 22 – – – – – – – Mini 2.5-1 Mini 3-1 Mini 3.5-1

Mini 4-2 Mini 6-2

5. Technical drawings

2.4 – 39 34 33 24 – – –

3.0 – 49 43 41 30 – – –

3.5 – 57 50 45 35 – – –

5.7 – – – – – 46 37 34

Min. water ﬂ ow to activate unit.

[ °C ]

2.4 – 22 19 17 13 – – –

3.0 – 27 24 22 17 – – –

3.5 – 31 28 25 19 – – –

5.7 – – – – – 26 20 19

Min. water ﬂ ow to activate unit.

* Note: Mini 2-1 is internally restricted to 0.32 gpm (1.2 l/min)

Figure A legend

1 Hot water connection

2 Cold water connection with ﬁ lter screen 3 Filter screen 4 Mounting holes

7 ½ ” (190 mm) 3 ¼ ” (82 mm)

” (4,8 mm)

” (143 mm)

mm)

3¾” (95

” (120 mm)

” (30 mm)

4 | MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS WWW.STIEBEL-ELTRON-USA.COM

(165 mm)

6½”

3/8” O.D. ﬂex connector

/16 ” (20 mm)

C26_02_05_0009

GENERAL INFORMATION | OPERATION

TECHNICAL DRAWINGS

ENGLISH

C26_02_05_0010

V >

p >

L N

™

2-1/2.5-1

Mini 3-1/3.5-1

™

4-2/6-2

Figure C legend

Electrical junction box 6 Water supply line for faucet installation 7 Sink 8 Cold valve (right) 9 Hot valve (left) 10

Shut off valve 11

Reset button from safety pressure cut out

L N GRD L L GRD Mini

WWW.STIEBEL-ELTRON-USA.COM MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS | 5

OPERATION

OVERVIEW

THIS MANUAL MUST BE READ CAREFULLY BEFORE ATTEMPTING TO INSTALL THE MINI™ WATER HEATER. IF YOU DO NOT FOLLOW THE SAFETY RULES OR THE INSTRUCTIONS OUTLINED IN THIS MANUAL, THE UNIT MAY NOT OPERATE PROPERLY AND IT COULD CAUSE PROPERTY DAMAGE, SERIOUS BODILY INJURY AND/OR DEATH.

STIEBEL ELTRON, INC. WILL NOT BE LIABLE FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION AND OPERATING INSTRUCTIONS OUTLINED IN THIS MANUAL OR BECAUSE OF IMPROPER USE. IMPROPER USE INCLUDES THE USE OF THIS APPLIANCE TO HEAT ANY LIQUID OTHER THAN WATER. FAILURE TO COMPLY WITH THE INSTALLATION AND OPERATING INSTRUCTIONS OR IMPROPER USE VOIDS WARRANTY. NEVER REMOVE THE UNIT’S COVER UNLESS THE ELECTRICITY IS TURNED OFF.

IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION OR OPERATION OF THIS WAT ER HEATER, OR IF YOU NEED ANY ADDITIONAL INSTALLATION MANUALS, PLEASE CALL OUR TECHNICAL SERVICE LINE ON 800-582-8423 (USA AND CANADA ONLY). IF YOU ARE CALLING FROM OUTSIDE THE U.S. OR CANADA, PLEASE CALL USA 413-247-3380 AND WE WILL REFER YOU TO A QUALIFIED STIEBEL ELTRON SERVICE REPRESENTATIVE IN YOUR AREA.

6. Overview

6.1 General Description

The Mini™ tankless water heater differs from conventional storage type water heaters in several ways. It does not store hot water. Instead, water is heated instantaneously as it ﬂ ows through the unit. The powerful heating elements are activated by a ﬂ ow switch as water is drawn from a hot water faucet connected to the Mini™. Due to the absence of stand-by losses, the Mini™ offers greater energy efﬁ ciency than storage type water heaters. The unit will continuously supply hot water as long as the faucet is open.

The temperature of the hot water delivered by the Mini™ depends on the wattage of the heating element, the temperature of the incoming cold water, and the water ﬂ ow rate through the unit. In order for the Mini™ to operate properly, it must be carefully matched to the application. In case you have questions regarding the way you plan to use the Mini™, please call our technical service line at 800-582-8423 (USA and Canada). For service outside the U.S. and Canada, please call us at USA 413-247-3380. You can also e-mail us at info@stiebeleltron-usa.com or fax us at 413-247-3369.

The Mini™ can be used for hand washing type applications in the U.S. and Canada:

– Restroom sinks in commercial/industrial facilities and homes – Kitchen areas in commercial /industrial facilities and homes – Cabins – Special uses in photo developing shops, laboratories etc.

6.2 Important information before supplying power to unit

Air in the cold water pipe will destroy the bare-wire



heating system of the Mini™. If the water supply to the Mini™ has been interrupted, for example due to the risk of frost or work on the water pipe, the following steps must be carried out before the unit is used again.

» 1. Turn off circuit breaker. » 2. Open a hot water tap downstream of the unit for as long as

is necessary for the unit and the cold water pipe to be free of air.

» 3. Turn on circuit breaker.

All information in these Instructions for Use and Installation must be followed carefully. They provide important information with regard to safety, operation, installation, and maintenance of the device.

6.3 Hot water output at max rated voltage

Model Wattage Typical hot water output

Mini™ 2-1* 1.8 kW 0.32 GPM Mini™ 2.5-1 2.4 kW 0.50 GPM Mini™ 3-1 3.0 kW 0.50 GPM Mini™ 3.5-1 3.5 kW 0.66 GPM Mini™ 4-2 3.5 kW 0.66 GPM Mini™ 6-2 5.7 kW 1.00 GPM

The Mini™ can also be used for whole apartments and homes in warm climate zones such as the Caribbean region, Central America and Mexico due to the higher ambient water temperatures.

6 | MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS WWW.STIEBEL-ELTRON-USA.COM

*Note: Mini™ 2-1 is internally restricted to 0.32 GPM (1.3 l/min)

INSTALLATION

INSTALLATION INSTRUCTIONS

6.4 Incorrect use

The following are not permitted and will void the factory warranty:

- Installation of the appliance where it is at risk from frost

- Installation in rooms where the appliance is at risk from explosions as a result of dust, gases or vapors

- Ignoring safety clearances and safety zones

- Incorrect power connection

- Operation of the appliance without water ﬂ owing through the unit, or with air in the lines (See section 8, “Initial start-up”, pg. 8)

- Operation of the unit with the cover off

- Heating liquids other than potable water

6.5 First steps to be taken in the event of malfunction

WARNING: ALWAYS SHUT OFF POWER AND WATER TO



THE UNIT PRIOR TO REMOVING THE FILTER SCREEN. FAILURE TO DO SO MAY CAUSE SERIOUS BODILY INJURY OR DEATH.

» Check the circuit breaker » Check the ﬁ lter screen for scale blockage or dirt accumulation.

See section 12, “Troubleshooting”, pg. 9.

6.6 Maintenance and care

MAINTENANCE WORK, SUCH AS CHECKING ELECTRICAL



SAFETY, MAY ONLY BE CARRIED OUT BY A QUALIFIED INSTALLER.

7.1 Mounting the unit

UNIT MUST BE INSTALLED WITH THE PLUMBING



CONNECTIONS POINTING DOWNWARD OR UPWARD ONLY.

WARNING: DO NOT INSTALL UNIT WHERE IT WOULD



ROUTINELY BE SPLASHED WITH WATER. ELECTRIC SHOCK

OR DEATH MAY RESULT.

» 1. Install Mini

point, for example, directly underneath the sink or next to the shower stall.

» 2. Install Mini

unit before freezing temperatures set in.

» 3. Leave a minimum of 5" of clearance on all sides for

servicing.

» 4. Remove plastic cover by removing screws located on the left

and right sides of the unit B.

» 5. Remove plastic backplate by pulling on the tab with a

screwdriver B.

» 6. Mount backplate securely to wall by putting two screws

through mounting holes

» 7. Snap unit back onto mounting plate » 8. Reinstall cover with screws on left and right side of unit

™

as close as possible to the hot water draw-off

™

in a frost free area. If frost may occur, remove

A B

7.2 Plumbing connections

NOTE: IF SOLDERING NEAR THE UNIT IS NECESSARY, PLEASE



DIRECT THE FLAME AWAY FROM THE HOUSING OF THE UNIT IN ORDER TO AVOID DAMAGE. EXCESSIVE HEAT FROM SOLDERING ON COP PER PIPES NEAR THE MINI™ MAY CAUSE DAMAGE. ALL PLUMBING WORK MUST COMPLY WITH NATIONAL AND APPLICABLE STATE AND LOCAL PLUMBING CODES.

ENGLISH

WARNING: ALWAYS SHUT OFF POWER AND WATER TO THE UNIT PRIOR TO REMOVING THE FILTER SCREEN.



FAILURE TO DO SO MAY CAUSE SERIOUS BODILY INJURY OR DEATH.

Regularly clean and descale the ﬁ lter screen located in the cold water inlet connection and if necessary replace. Always shut off power and water to the unit prior to removing the ﬁ lter screen.

A damp cloth is sufﬁ cient for cleaning of the unit's housing. Do not use any abrasive or corrosive cleaning agents.

7. Installation instructions

KEEP THESE INSTRUCTIONS CAREFULLY AND PASS THEM



ON TO YOUR SUCCESSOR IN THE EVENT OF A CHANGE IN OWNERSHIP, IN THE EVENT OF MAINTENANCE AND POSSIBLE REPAIR WORK THEY SHOULD BE PASSED TO THE QUALIFIED INSTALLER FOR HIS OR HER REFERENCE.

WWW.STIEBEL-ELTRON-USA.COM MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS | 7

» 1. All plumbing work must comply with national and

applicable state and local plumbing codes.

» 2. A pressure reducing valve must be installed if the cold water

supply pressure exceeds 150 PSI (10 bar).

» 3. Make certain that the cold water supply line has been

ﬂ ushed to remove any scale and dirt.

» 4. Install isolating valve in cold water line as shown in

illustration C. This allows the unit to be isolated for maintenance purposes.

» 5. Cold water connection (inlet) is on the right side of the unit,

hot water connection (outlet) is on the left side of unit.

» 6. Tankless water heaters such as the Mini

to be equipped with a Pressure and Temperature Relief Valve (except in Massachusetts). If the local inspector will not pass the installation without a P+T valve, it should be installed on the hot water outlet side of unit.

» 7. The Mini

steel hose with a 3/8˝ O.D. Tube Outlet.

» 8. When all plumbing work is completed, check for leaks and

take corrective action before proceeding.

™

is designed for connection to a braided stainless

™

are not required

INSTALLATION

elec tr

o n ic

°C

INITIAL START-UP

7.3 Electrical connection

WARNING: BEFORE BEGINNING ANY WORK ON THE



ELECTRIC INSTALLATION, BE SURE THAT THE MAIN CIRCUIT BREAKER PANEL SWITCH IS “OFF” TO AVOID ANY DANGER OF ELECTRIC SHOCK. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. ALL MOUNTING AND PLUMBING MUST BE COMPLETED BEFORE PROCEEDING WITH ELECTRICAL HOOK-UP. WHERE REQUIRED BY LOCAL, STATE OR NATIONAL ELECTRICAL CODES, THE CIRCUIT SHOULD BE EQUIPPED WITH A GROUND FAULT INTERRUPTER.

WARNING: AS WITH ANY ELECTRIC APPLIANCE, FAILURE TO ELECTRICALLY GROUND UNIT MAY RESULT IN SERIOUS INJURY OR DEATH.

CAUTION: INSTALLING A MINI™ 2-1, MINI™ 2.5-1, MINI™ 3-1, OR MINI™ 3.5-1 ON A 208 V OR 220–240 V CIRCUIT WILL DESTROY THE HEATING ELEMENT. THIS IS CONSIDERED IMPROPER INSTALLATION AND WILL VOID YOUR FACTORY WARRANTY.

Voltage

Mini™ 2-1: 110–120 V Mini™ 2.5-1: 110–120 V Mini™ 3-1: 110–120 V Mini™ 3.5-1: 110–120 V Mini™ 4-2: 220–240, 208 V Mini™ 6-2: 220–240, 208 V

1. All elec trical work must comply with national and applicable s tate and local electrical codes.

2. The Mini™ should be connected to a properly grounded dedicated branch circuit of proper voltage rating. In installa tions with several Mini™ units, each unit requires an independent circuit. Please refer to the technical data table for the correct wire and circuit breaker size.

3. The open ends of the “pigtail” must be feed into an electrical junction box. Then feed wires through strain relief clamp and tighten clamp down on wire.

4. Reinstall plastic cover.

8. Initial start-up

WARNING: OPEN HOT WATER FAUCET FOR A FEW MINUTES



UNTIL WATER FLOW IS CONTINUOUS AND ALL AIR IS PURGED FROM WATER PIPES. THE UNIT’S PLASTIC COVER MUST BE INSTALLED BEFORE THE CIRCUIT BREAKER IS TURNED ON.

26_02_02_0436

9. Water heater hand over

Explain the functions of the unit to the user and familiarize him or her with its use.

Important instructions:

» Draw the user’s attention to possible hazards (scalding). » Hand over these instructions for future reference. » In order to obtain a proper temperature at a single spout

mixer-type faucet, restrict cold water ﬂ ow to faucet by partially closing the cold water shut-off valve under the sink until cold water and hot water ﬂ ow rates are approximately the same.

10. Normal maintenance

CAUTION: OTHER THAN THE FILTER SCREEN, THE MINI™



DOES NOT CONTAIN ANY PARTS SERVICEABLE BY THE LAY PERSON. IN CASE OF MALFUNCTION PLEASE CONTACT A LICENSED PLUMBER OR ELECTRICIAN.

Stiebel Eltron Mini™ tankless heaters are designed for a very long service life. Actual life expectancy will vary with water quality and use. The unit itself does not require any regular maintenance. However, to ensure consistent water ﬂ ow, it is recommended to periodically remove scale and dirt that may build up at the aerator of the faucet or in the shower head. Also, the Mini™ has a built in ﬁ lter screen that should be cleaned from time to time. In order to do this, turn off the cold water supply at the isolating valve. Clean screen and put the screen back into its original position.

8 | MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

TECHNICAL DATA

11. Technical data

Mini™ 2-1 Mini™ 2.5-1 Mini™ 3-1 Mini™ 3.5-1 Mini™ 4-2 Mini™ 6-2

Item number 231045 232098 220816 232099 222039 220817

Phase 1 1 1 1 1 1

Voltage 110–120 V 110–120 V 110–120 V 110–120 V 220–240 V 208 V 220–240 V 208 V

Wattage 1.8 kW 2.4 kW 3.0 kW 3.5 kW 3.5 kW 2.6 kW 5.7 kW 4.3 kW

Max. amp, load 15 A 20 A 25 A 29 A 14.6 A 12.7 A 23.8 A 20.6 A

Required circuit

breaker size

Required wire size

Minimum water flow

to activate unit

Recommended inlet

temp. range 41–77 °F (5–25 °C)

Nominal water volume 0.026 gal (0.1 l)

Max. working pressure 150 psi (10 bar)

Tested to pressure 300 psi (20 bar)

Weight 3.44 lbs. (1.56 kg)

Height

Depth Width

20 A 30 A 30 A 40 A 20 A 20 A 30 A 30 A 12 AWG 10 AWG 10 AWG 10 AWG 12 AWG 12 AWG 10 AWG 10 AWG

0.21 GPM (0.8) l/min

6½˝ (165 mm) 3¼˝ (82 mm) 7½˝ (190 mm)

0.40 GPM (1.5) l/min

ENGLISH

0.77 GPM (2.9) l/min

Water connections for 3/8˝ O.D. flex connector

Heating system Nichrome bare-wire

Mini™ 2-1 models are internally restricted to 0.32 gpm. Mini™ 2-1, 2.5-1, 3-1 ship with a 0.5 gpm pressure compensating ﬂ ow reducer/aerator that should be installed. Mini™ 3.5-1, 4-2 ship with a 0.66 gpm pressure compensating ﬂ ow reducer/aerator that should be installed.

-Tankless water heaters are considered a non-continuous load

-Conductors should be sized to maintain a voltage drop of less than 3 % under load

-For use with cold water supply only

12. Troubleshooting

Symptom Possible cause Solution

No hot water despite fully opened hot water faucet.

No electrical power. Check the circuit breaker and

check voltage at the wiring block.

The activation ﬂ ow rate needed to turn on the heating element has not been reached.

Safety cut out tripped – turn circuit breakers off

Clean ﬁ lter screen.

– open Hot Valve to release pres-

sure from the unit – reset saftey pressure cut out – turn circuit breakers on

WWW.STIEBEL-ELTRON-USA.COM MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS | 9

INSTALLATION

SPARE PARTS

13. Spare parts

Spare Part (all Mini™ models) Item no.

1 Front cover 271010 2 Rear housing 271011 3 Filter screen 272884 4 Plumbing connections 272777 5 O-rings (not shown) 083043

10 | MINI™ SERIES TANKLESS ELECTRIC WATER HEATERS WWW.STIEBEL-ELTRON-USA.COM

+ 22 hidden pages

STIEBEL ELTRON MINI 2.5-1, MINI 3-1, MINI 3.5-1, MINI 4-2, MINI 6-2 Operation And Installation

Specifications and Main Features

Frequently Asked Questions

User Manual