Sterex SX-B User Manual

SX-B

Epilator Manual

Sterex Electrolysis International Ltd

Contents

• Introduction

• Technical Data Sheet

• Accessories & Controls

• Theory

• Treatment Techniques

• Hints & Tips

• Diathermy/Thermolysis only operation

• Testing Procedure

Introduction

Thank you for buying the Sterex

SX-B Blend epilator.

It is essential that you read the
following pages of this manual and
work through the practical CD,
which is included with your SX-B
Blend epilator, before you operate
this unit. (

Video available on request)

Technical Data Sheet

• ADDRESS: Sterex Electrolysis International Ltd

174 Kings Rd
Tyseley

Birmingham
B11 2AP
U.K.
Tel : [phone] Fax: [phone]

• EQUIPMENT CLASSIFICATION:

Class 1 Type B Applied Parts.

The equipment is designed for continuous operation.
The equipment is not protected against ingress.
Do not use the equipment near flammable anaesthetic gases.

Type B Equipment

No other electrical equipment may be connected to the patient simultaneously when using this
epilator equipment.

• SYMBOLS

Applied parts Type B

Potentially Hazardous Output
The manual must be read before using this equipment.

• E.M.C. DIRECTIVE

The EUT (Equipment Under Test) complies with European Electromagnetic Compatibility
requirements. However, the EUT may emit electromagnetic radiation, which may interfere with other
equipment in the vicinity. Likewise other equipment may interfere with the EUT. If such effects are
to be minimised, increasing the distance between equipment and reducing cable lengths where
relevant should help.
It is advisable not to use such equipment on people fitted with pace makers and to take medical
advice if fitted with any electrical devices.
It is not recommended to use epilators within 3 metres of sensitive electrical appliances such as
computers, medical equipment etc.

• MEDICAL DEVICES DIRECTIVE

The SX-B conforms to the Medical Devices EN60601 – 1:1990: Notified Body number = 0120

• FUNCTION

The function of the epilator is to remove body and facial hair using Thermolysis/Diathermy and
Galvanic or a combination of the two techniques called “Blend”.

• MAINTENANCE

The exterior of the epilator should be cleaned regularly with a dusting brush/cloth. Dirt, which is
difficult to remove, can be cleaned off with a moistened cloth (99% water 1% mild detergent). The
equipment must be wiped dry with a lint free cloth. Under no circumstances must the cleaning fluid
get into the equipment. The use of other cleaning agents may attack the plastic and paint surface.

Safety/Preventative Maintenance

The equipment operates according to safety Class 1 (three-conductor power cord with protective
earth contact). The mains/line plug shall only be inserted into a socket outlet protected with a
protective earth contact. The protective action must not be negated by the use of an extension cord
without a protective conductor.

The ground accessible metal parts (case, sockets, jacks) and the mains/line supply contacts (line/live,
neutral) of the epilator have been tested against insulation breakdown.

Whenever it is likely that protection has been impaired, the equipment shall be made inoperative and
be secured against any unintended operation.

The protection is likely to be impaired if, for example, the equipment/mains cable:

1. Shows visible signs of damage

2. Fails to perform the intended user operation

3. Has been subjected to prolonged storage under unfavourable conditions e.g. in an open or
moist environment

4. Has been subjected to severe transport stress

• SERVICING OF EQUIPMENT

Servicing of the equipment may only be carried out by Sterex Electrolysis International Ltd or by
persons authorised by them.

• SPECIFICATIONS

Operating Temperature 10 degrees C to 50 degrees C
Lines/Mains Voltage 230/240V ac
Mains Frequency 50/60 Hz
Power Consumption 35 Watts approx.
Maximum Ambient Temperature -10 degrees C to + 40 degrees C
Protective System Class 1 Type B
Weight 2.75 kilos approx.

Maximum available Thermolysis/RF
Output Power

Thermolysis/RF Output Frequency 13.56 MHz
DC/Galvanic Output 0-15 Volts at a maximum current of 1 mA

• RANGE & ACCURACY OF DISPLAYED VALUES

Meter Accuracy Available Output Power Thermolysis/RF 0-100% In 1% steps 0-2 Watts Galvanic/DC 0-100% In 1% steps 0-15 mW Timer 0-9.95 secs In 0.5 second steps

• ENVIRONMENTAL & STORAGE CONDITIONS

The permissible ambient temperature range for storage or transportation is -40 degrees C to +70
degrees C. The maximum operating altitude is up to 15000M.
The maximum relative humidity is up to 80%.

• OPERATING CONDITIONS

The equipment has been designed for indoor use. The permissible ambient temperature range during
operation is -10 degrees C to +40 degrees C. If condensed water exists in the instrument it should be
acclimatised before switching on. The epilator should be kept in a clean dry room, and must not be
operated in explosive, corrosive, dirty or moist environments.

0-2 Watts measured using a 5 K Ω non-
inductive Load Resistor