STEINEL RC3 User Manual
RC 3 Service Remote
1
4
5
8
10
11
2
3
6
7
9
12
Functions
Reach setting (Control Pro Ultrasonic and
Dual tech sensors only)
1
Ultrasonic coverage can be selected from
minimum, 1/3, 2/3, or maximum by pressing
these buttons. Use this setting to increase or
decrease the coverage (detection range) of
the sensor.
Time setting CH 1
-
Stay 'ON' time for switching contact 1
2
The period of time you want the light to stay
'ON' for after last detecting movement can
be set from between 30 sec., 2 min., 5 min.,
15 min. and 30 min. by pressing these
buttons.
3
Setting the light to stay 'ON' for a time of your
own choice. Each press of the button increments the chosen time setting by 1 minute.
IQ mode. Stay 'ON' time is self-learning and
4
adjusts dynamically to user behaviour.
The optimum time is determined by means of
a learning algorithm. The shortest time is 2
min., the longest time 20 min.
5
Test mode. The test mode has the purpose of
checking for proper working order as well as
testing the detection zone. The presence de
tector switches 'ON' for approx. 8 sec. regardless of brightness and movement. The
test mode has priority over all other settings.
All user-selected potentiometer settings apply
in normal mode. The test mode ends automatically after 10 min.
Time setting CH 2 -
Stay 'ON' time for switching contact 2 (HVAC)
6
The period of time you want the HVAC con-
tacts to signal the HVAC controller (stay 'ON')
after
last detecting movement can be set from 1
min., 5 min., 30 min., or 2 hours by pressing
these
buttons.
Light level setting
7
The chosen response threshold can be varied
from approx. 10 – 1000 lux / 1 - 100 fc.
8
Night-time mode (minimum setting
approx. 10 lux. , 1 fc.)
9
Daylight mode (maximum - light level function
overridden)
10
Teach-IN. Twilight setting at the memory but
ton/Teach mode. This button must be pressed
at the level of light at which you want the sensor to respond to movement. The current light
level is saved.
Sensor sensitivity (Ultrasonic and Dual tech only)
11
Ultrasonic sensitivity can be reduced by
pressing the button
stores normal sensitivity. Use this setting to
. The button re
-
adjust the amount of motion required within
the detection area
before the sensor will trigger.
Reset
12
Resets all settings to the values selected on
the detector manually or to the factory set
-
tings.
RC3
Description
The RC 3 service remote (commissioning tool)
gives the installer the ability to set basic
functions of the entire line of Control Pro
sensors via remote control. Each valid press of
a button is indicated by a blue LED flash on the
sensor.
www.steinel.net (800) 852-4343
www.steinel.net (800) 852-4343
Project Name:
Address:
Commissioning Agent:
Agent’s Phone #:
Date:
Line Room #Sensor Model Ultrasonic
Reach/Distance
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Time Delay HVAC Delay OFF
(COM2-24 Only)
Light Level Ultrasonic
Sensitivity
Reset Notes
Warranty
STEINEL America warrants its products
against defects in material or workmanship
for a period of five years. STEINEL will
replace or repair the item provided that it
has not been altered or subjected to abuse,
accident, improper installation or improper
use. There are no obligations or liabilities
on the part of STEINEL for consequential
damages arising out of or in connection with
the use or performance of this product or
other indirect damages with respect to loss
of property, revenue, or profit, or cost of
removal, installation or reinstallation.
STEINEL America Inc.
9051 Lyndale Avenue South
USA - Bloomington, MN 55420
Tel: +1-952-888-5950
Fax: +1-952-888-5132
www.steinel.net
Technical changes subject to no prior notification.
M-11161-1
Loading...