State SSE5-120 User Manual

COMMERCIAL

MODELS

SSE 5 – 120

HEAVY DUTY COMMERCIAL
ELECTRIC WATER HEATERS

FEATURES

ADVANCED ELECTRONIC CONTROL

State’s new proprietary electronic water heater control provides precise + or – 1°F
temperature control that is ideal for industrial and food service applications where exact
temperatures of hot water are needed.

iCOMM™ Compatible - Call 1.888.WATER02 for more information.

Plain English Text – Animated icons display detailed operational and diagnostic
information. Fault or Alert messages appear if an operational issue occurs.

Element Sensing – Each element is constantly monitored and current on/off state is displayed,
any element failure is reported and its exact location is shown. Eliminates guesswork, makes
troubleshooting easy and helps keep the unit operating at maximum performance.

Low Water Cut Off – Factory standard on-board low water cutoff uses a remote
electronic immersion type probe to prevent energizing of the elements in the event of
low water condition and eliminates accidental dry firing.

Sequencing – Units with multiple element contactors are sequenced on with one-second
delay between stages. Prevents high amp electrical loads from hitting the electric system
all at once and provides a smoother operating unit. An adjustable modulating control is
optional (See options).

For more information on Select® contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015

800.365.0024 Toll-free USA
www.statewaterheaters.com

SCESS00708 April 2011R

Economy Mode Operation – Control system automatically lowers the operating set
point by a programmed value during user-defined time periods. Seven-day clock may be
programmed for night set back and/or weekend shutdown to reduce operating cost and
save energy.

INCOLOY IMMERSION HEATERS – Heavy-duty medium watt density elements

have incoloy sheathing and prewired leads: provides excellent protection against
oxidation and scaling. Input ranges from 3kW to 90kW available (see accompanying
chart).

HEAVY FOAM INSULATED – All models meet or exceed the standby loss

requirements of ASHRAE 90.1b-1992 and ASHRAE/IESNA 90.1-2004.

GLASS-LINED TANK – Glass coating provies superior protection against corrosion

and is bonded to all inner tank surfaces at 1600˚ F.

ASME TANK CONSTRUCTION – 125 psi working pressure (65 thru 120 gallons), 150

psi working pressure (5 thru 50 gallons).

THREE YEAR LIMITED WARRANTY – For complete warranty information consult

written warranty or contact State.

SOLID.STATE.

COMMERCIAL

FEATURES (Continued)

STANDARD VOLTAGES – 208, 240 and 480 volt single and three phase. Single phase 208 and 240 are convertible to three phase. All 208 and 240

volt at 24kW and below are supplied phase convertible (single to three and vice versa). 277 volt single phase also available. Consult factory for 120
volt power circuit availability.

TERMINAL BLOCK – To accept copper or aluminum leads (on units with more than one contactor).

120 VOLT CONTROL CIRCUIT – 120 volt control circuit powered by fused transformer.

MAGNETIC CONTACTORS – Heavy-duty UL rated for 100,000 cycles.

POWER CIRCUIT FUSING (120 AMP CURRENT DRAW AND ABOVE) – Meets National Electric Code and UL requirements

that water heaters must have internal fusing when current draw exceeds 120 amps.

SIMPLIFIED CIRCUITRY, COLOR-CODED FOR EASE OF SERVICE

BRASS DRAIN VALVE

HINGED CONTROL COMPARTMENT DOOR

CSA CERTIFIED AND ASME RATED T&P RELIEF VALVE

For more information on Select® contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015

800.365.0024 Toll-free USA
www.statewaterheaters.com

SCESS00708

April 2011R

SOLID.STATE.