C O M M E R C I A L
SANDBLASTER
ULTRA-LOW NOX
COMMERCIAL GAS TANK-TYPE WATER HEATERS
®
SBL81 199 NE & SBL100 199 NE
Series 200
FEATURES
80% Thermal Efficiency
Means Lower Operating Costs
Fan Assisted Combustion
• The blower is built into the low NOx burner
assembly. Complies with California SCAQMD
Rule 1146.2 and other air quality management
districts with similar NOx emission requirements
of 14 ng/J or 20 ppm.
Air Flapper
• A stainless steel air flapper is used inside the premix
system to replace externally mounted flue damper to
minimize the standby heat loss and to minimize the
overall heater height
Metal Venting
• Rated Category I Appliance. Uses standard
double wall type “B” vent
• Can be commonly vented with other
Category I appliances
• Vent connects directly to the vent connector outlet
• An excellent choice for retrofit and upgrade
installations
Water Connections
• For ease of installation, all SBL’s feature water
connections on the top, front, and rear.
• “Hydro Cannon” inlet water connection
eliminates harmful scale buildup, extending
the life of the product
• The front inlet connection must be used for the
Hydro Cannon benefits
Glasslined Tank
• Glass is applied after the complete tank has been
assembled to give a seamless barrier against
corrosion by hot water
Installed Cost Savings
• When multiple SBL units are exclusively used
in a vent manifold, use the National Fuel Gas
Code Table 13 Fan Sizing Charts to determine
vent diameter and specifications
• The SBL uses a smaller vent diameter than a natural
draft water heater which saves on installation cost
Fully Automatic Digital
Control with Safety Shutoff
• Accurate, dependable control system
• Manual reset gas shutoff device for added safety
• Maximum inlet gas pressure is 14” W.C. minimum
gas pressure is 3.5” W.C. natural gas
Foam Insulation
• Saves fuel, helps reduce standby heat loss
Jacket
• Heavy gauge steel finished with a baked enamel
finish over a bonderized undercoat
Easy Cleaning
• Handhole cleanout allows access for easy cleaning
Fully Tested for Safety
and Performance
• Design certified by the Underwriters Laboratory
for 180°F hot water service
• Meets rigid requirements of the National Sanitation
Foundation when equipped with optional leg kit
• Certified for use on combustible flooring
Intermittent Ignition Device
• Eliminates standing pilot
• Provides flame failure response in less than
one second
• Spark ignitor and power ON/OFF switch
Easy to Install
• Completely factory-assembled
• Only gas, water, vent and electric connections
need be made
• Provided with drain valve
Anodes
• Long-life, stainless steel core anode rods
Plug Kits
• Pipe nipples and caps are included to plug unused
water connections
Approval Ratings
and Certification
• All models meet ANSI Z21.10.3 - CSA 4.3
standards and the thermal efficiency and standby
loss requirements of the U.S. Department of Energy
and current edition of ASHRAE/IESNA 90.1
Other Features
• Integral automatic gas shutoff system prevents
excessive water temperature
• CSA Certified and ASME Rated T&P Relief Valve
are factory-installed
• Maximum working pressure is 160 psi standard
• Adjustable thermostat with a 120-180°F range
NSF Leg Kit
• Meets NSF Standard 5 with optional leg kit Part # 9008883005
Three Year Limited Tank
Warranty / One Year Limited
Parts Warranty
• For complete warranty information, consult
written warranty
For more information on Ultra-Low NOx, contact:
State Water Heaters
500 Tennessee Waltz Parkway
Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com
SCGSS00114
C O M M E R C I A L
ULTRA-LOW NOX COMMERCIAL TANK-TYPE GAS
WATER HEATERS
ROUGH IN DIMENSIONS
SBL Models
ROUGH IN DIMENSIONS
MODEL
DIMENSION INCHES CM INCHES CM
A 63 3/4 161.93 71 3/4 182.25
B 37 93.98 37 93.98
C 65 165.1 73 185.42
D 52 3/4 133.99 60 3/4 154.31
E 20 3/4 52.71 20 1/2 52.07
F 21 53.34 21 53.34
G 3/4 NPT 3/4 NPT
H 53 134.62 61 154.94
I 6 15.24 6 15.24
J 27 3/4 70.49 27 3/4 70.49
K 1 1/2 NPT 1 1/2 NPT
L 1 1/2 NPT 1 1/2 NPT
Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement
Models rated at 80% thermal efficiency
Models available for sale in California only
SBL81 199 NE SBL100 199 NE
SCGSS00114 Page 2 of 4
RECOVERY CAPACITIES, BASED ON 80% EFFICIENCY
U. S. GALLONS / HR. AND LITERS / HR. AT TEMPERATURE RISE INDICATED
INPUT
SBL81 199 NE
INPUTkWU.S.
BTUH
199000 81 80 GPH 531 478 382 354 319 273 265 239 212 191 177 174 159 152 147 137
GAL. LITERS
45 307 LPH 2009 1808 1447 1340 1206 1033 1005 904 804 723 670 658 603 574 556 517
EFF.
DEG. F 36 40 50 54 60 70 72 80 90 100 108 110 120 126 130 140
%
DEG. C 20 22 28 30 33 39 40 44 50 56 60 61 67 70 72 78
C O M M E R C I A L
SBL100 199 NE
199000 100 80 GPH 531 478 382 354 319 273 265 239 212 191 177 174 159 152 147 137
45 352 LPH 2009 1808 1447 1340 1206 1033 1005 904 804 723 670 658 603 574 556 517
GAS AND ELECTRICAL CHARACTERISTICS
MODEL GAS TYPE
SBL81 199 NE
SBL100 199 NE
MODEL SIDES & REAR TOP COVER SIDES & REAR TOP COVER
SBL81 199 NE
SBL100 199 NE
Models Top Front Back Top Front Back
SBL81 199 NE
SBL100 199 NE
Natural 3.5” W.C. (0.87 kPa) 14” W.C. (3.48 kPa) 120 / 60 < 5
Natural 3.5” W.C. (0.87 kPa) 14” W.C. (3.48 kPa) 120 / 60 < 5
CLEARANCE TO COMBUSTIBLES CLEARANCE TO NON-COMBUSTIBLES
0” 12” 0” 12”
0” 12” 0” 12”
WATER CONNECTIONS IN INCHES
INLET OUTLET
1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2
1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2
MINIMUM MAXIMUM
GAS SUPPLY PRESSURE
VOLTS / HZ AMPERES
SBL81 199 NE SBL100 199 NE
Approx. Shipping Weight 650 lbs. 295 kg. 750 lbs. 341 kg.
SCGSS00114 Page 3 of 4
C O M M E R C I A L
SAMPLE SPECIFICATION
Water Heater(s) shall be Model __________ as manufactured by STATE, or equal. Water heater(s) shall be of glasslined design, and gasfired, equipped to burn natural gas and design
certified by the Underwriter Laboratory under Volume III tests for commercial heaters for delivery of 180°F water, and meets the thermal efficiency and standby loss requirements
of the U.S. Department of Energy and Current Edition of ASHRAE/IESNA 90.1. Heaters shall have an input rating of __________ and a recovery rating of __________ GPH at
a temperature rise of 100°F with a storage capacity of __________ gallons. Heaters shall be equipped with 1 1/2” water inlet and outlet openings, a 2 3/4” x 3 3/4” boiler-type handhole
cleanout and shall have a maximum working pressure of 160 psi. Water heater(s) shall be equipped with an integrated control system consisting of a 180°F adjustable thermostat with
upper and lower sensing bulbs, which average the water temperatures at the top and bottom of the tank for maximum water temperature control. Heater(s) shall be provided with a
manual reset gas shutoff device, anodes for cathodic protection and IID system. CSA Certified and ASME Rated T&P Relief Valve shall be furnished and installed by the factory.
The heater shall be insulated with foam insulation or equal. The outer jacket shall have a baked enamel finish over a bonderized undercoating. All internal surfaces of the heater(s)
exposed to water shall be glass-lined with an alkaline borosilicate composition that has been fused-to-steel by firing at a temperature range of 1400° to 1600°F. Heater tank shall have
a 3 year limited warranty against corrosion or sediment buildup as outlined in the written warranty. Fully illustrated instruction manual to be included.
For complete information on limited warranties, consult written warranty or contact
the State Customer Care Center at 1-800-365-0024.
State Industries, Inc., reserves the right to make product changes or improvements without prior notice.
For more information on Ultra-Low NOx, contact:
State Water Heaters
500 Tennessee Waltz Parkway
Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com
SCGSS00114 Page 4 of 4 © 2014 State Industries, Inc. Printed in U.S.A
Loading...