StarTech.com SV231DLU3A Owner's Manual

Manual Revision: 11/12/2013

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com

SV231DLU3A / SV431DLU3A

2/4 Port SuperSpeed USB 3.0 Dual-Link DVI
KVM Switch with Audio and Cables

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual

i

Table of Contents

Product Diagram ....................................................................................1

Front View - SV231DLU3A ...................................................................................................................... 1

Rear View ..................................................................................................................................................... 1

Front View - SV431DLU3A ...................................................................................................................... 2

Rear View ..................................................................................................................................................... 2

Introduction ............................................................................................ 3

Packaging Contents .................................................................................................................................3

System Requirements ..............................................................................................................................3

Installation ..............................................................................................4

Hardware Installation ..............................................................................................................................4

Driver Installation ...................................................................................................................................... 4

Operation ................................................................................................5

Front Panel ................................................................................................................................................... 5

Hotkey Control ........................................................................................................................................... 5

Specications .......................................................................................... 8

Technical Support ..................................................................................9

Warranty Information ............................................................................ 9

Instruction Manual

1

Product Diagram

Front View - SV231DLU3A

PC1

connectors

USB Keyboard/

Mouse

Connectors

Console DVI-I

Connector

(output)

DC Power

Connector

USB 3.0 HUB

connectors

3.5mm Audio
Speaker/Mic

Rear View

USB Hub

Selection LED

Port Selection

Button / LED

Instruction Manual

2

Front View - SV431DLU3A

Rear View

USB Hub

Selection LED

Port Selection

Button / LED

PC1

connectors

USB Keyboard/

Mouse

Connectors

Console DVI-I

Connector

(output)

DC Power

Connector

USB 3.0 HUB

connectors

3.5mm Audio
Speaker/Mic

Instruction Manual

3

Introduction

Packaging Contents

SV231DLU3A

• 1 x 2 Port USB 3.0 KVM Switch

• 2 x DVI-D M/M Cables

• 2 x USB 3.0 A-B Cables

• 2 x 3.5mm Audio/Mic Cables

• 1 x Universal Power Adapter (NA/ UK/ EU)

• 1 x Instruction Manual

SV431DLU3A

• 1 x 4 Port USB 3.0 KVM Switch

• 4 x DVI-D M/M Cables

• 4 x USB 3.0 A-B Cables

• 4 x 3.5mm Audio/Mic Cables

• 1 x Universal Power Adapter (NA/ UK/ EU)

• 1 x Instruction Manual

System Requirements

• One DVI display device (i.e. monitor, projector, TV, etc.)

• A DVI output for each computer

• USB enabled computer system with available USB port

• Standard 104-key keyboard

• Standard 3-button mouse

Instruction Manual

4

Installation

Hardware Installation

1. Connect a DVI monitor into the Console’s DVI connector; plug a USB keyboard and a
USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch. If
using audio, also connect speakers with 3.5mm mini-jack plugs.

2. Use a male-to-male DVI-D video cable to connect the DVI connector on the
computer’s video card, to the DVI ports for one of the KVM’s PC ports (i.e. PC1).

3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector)
for the PC port used in Step 2, and the USB port on the computer (type A, at
connector). If using audio, connect 3.5mm mini-jack cables from the PC port to the
sound card.

4. Repeat Steps 2 and 3 for each PC port on the KVM switch, or each computer you
wish to use on the KVM.

OPTIONAL: Connect any other USB peripherals you wish to share between the
connected computers/devices to the extra USB Hub port on the Console side.

5. Connect the external power adapter from a wall outlet to the power connector on
the rear panel of the KVM switch.

6. Power up the rst computer/device and wait for it to fully boot and test keyboard/
mouse functionality.

7. Once operation has been successfully conrmed, switch to the next port and power
up that computer/device and conrm.

8. Once completed for all computers/devices connected to the KVM switch, you
should be able to switch between ports freely.

Driver Installation

No driver installation is required for the KVM switch, as the keyboard/mouse use USB
drivers that are already installed on any operating system that fully supports USB.

Instruction Manual

5

Operation

Front Panel

The front-panel Smart Touch button allows you a direct control over KVM switching
operation. Simply press the button to switch to the respective PC port. For more
operation about Smart Touch button, please refer to “Quick Reference Sheet”.

Hotkey Control

A Hotkey command is a short keyboard sequence for selecting a computer, activating
computer scan, etc. A hotkey sequence starts with two left <ScrLk> keystrokes
(successively within 2 seconds) followed by one or two more keystrokes. A built-in
tone generator creates a high-pitch beep for correct hotkey command; otherwise, one
low-pitch beep is generated for errors and the bad key sequence will not be forwarded
to the selected computer.

Please refer to the “Quick Reference Sheet” for available commands

Quick Reference Sheet

Command Hotkeys

Front-Panel

Smart Touch

Button

Description

Select PC Port

(Jointly select

PC port/ hub
port control/

audio&mic,

if binding is

enabled)

ScrLk + ScrLk +

(1~2/1~4)

Touch the

corresponding

button to select

the active PC port.

Select the PC port

Select Hub Port

Control (Jointly

select PC and

hub port control,

if binding is

enabled)

ScrLk + ScrLk +

F1~F2/F1~F4

Touch the button

to toggle the

specic PC+USB

hub port control.

(It works only if
PC port/ hub port
control binding is

enabled.)

Move Hub Port

(1~2 / 1~4)

Instruction Manual

6

Quick Reference Sheet

Command Hotkeys

Front-Panel

Smart Touch

Button

Description

Select Audio&Mic

Port (Jointly

select PC port

and audio&mic,

if binding is

enabled)

ScrLk + ScrLk +

F5~F6/F5~F8

--

Move audio&mic

port

Bind PC and Hub

Port Control

Switching

ScrLk + ScrLk + Z --

Bind PC Port with

Device Hub Port

Unbind PC and

Hub Port Control

Switching

ScrLk + ScrLk + X --

Unbind PC Port

with Device Hub

Port

Bind PC and

Audio&Mic

Switching

ScrLk + ScrLk + Q --

Bind PC Port with

audio&mic Port

Unbind PC and

Audio&Mic

Switching

ScrLk + ScrLk + W --

Unbind PC port

with audio&mic

Port

Previous PC port

(Jointly select PC/

hub port control,

if binding is

enabled)

ScrLk + ScrLk + Up

Arrow

-- Next lower PC Port

Next PC port

(Jointly select PC/

hub port control,

if binding is

enabled)

ScrLk + ScrLk +

Down Arrow

--

Next higher PC

Port

Instruction Manual

7

Quick Reference Sheet

Command Hotkeys

Front-Panel

Smart Touch

Button

Description

Previous active PC

port

ScrLk + ScrLk +

[Backspace]

--

Previous active

PC Port

Beeper ScrLk + ScrLk + B --

Toggle Beeper

On/O

Dene Hotkey

Preceding
Sequence

ScrLk + ScrLk +

H+ [ScrLk/CapsLk/

Esc/F12/ NumLk/

left Ctrl/ right Ctrl]

Press and hold

down last button

(Button 2/

Button 4) till two

beeps. Release

the button, and

press desired

hotkey preceding

sequence.

Select Hotkey

Header [ScrLk/

CapsLk/ Esc/ F12/

NumLk/ left Ctrl/

right Ctrl]

Autoscan ScrLk + ScrLk + S -- Start Autoscan

Autoscan with

Programmable

Delay Time

ScrLk + ScrLk + S

+ (1~6)

1 10s ; 2 20s ;

3 30s ;

4 40s ; 5 50s ;

6 60s

--

Autoscan duration

adjust to (10~60

seconds)

Stop Autoscan [Any key] Touch any button

Stop Autoscan

during scan mode

Instruction Manual

8

Specications

SV231DLU3A SV431DLU3A

Console Connectors

1 x DVI-1 (29 pin) Female

2 x USB A (4 pin) Female

2 x 3.5mm Mini-Jack (3 Position) Female

Computer Connectors

(per port)

1 x DVI-1 (29 pin) Female

1 x USB 3.0 B (9pin; SuperSpeed) Female

2 x 3.5mm Mini-Jack (3 Position) Female

Other Interfaces 2 x USB 3.0 A (9 pin; SuperSpeed) Female

LEDs

2 x PC Selection Indicator

2 x Hub Selection

Indicator

4 x PC Selection

Indicator

4 x Hub Selection

Indicator

Switching Modes Pushbutton, Hot-key

Maximum Resolution 2560x1600

Audio Support Yes (2-Channel Stereo)

On Screen Display No

Cascadable No

Rack-Mountable No

Enclosure Type Steel

Operating Temperature 0°C to 40°C (32°F to 104°F)

Storage Temperature -20°C to 40°C (4°F to 104°F)

Humidity 0~90% RH Non-Condensing

Dimensions (LxWxH) 165 x 89 x 46mm 265 x 102 x 46mm

Weight 940g 1000g

Power 9V 1A

Instruction Manual

9

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.

We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.

Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.

StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.