Secure Articulating Universal Tablet Mount
Quick-Start Guide
Product Diagram (SECTBLTDT)
Rear View
Component Function
1 Tablet Holder
2 Lock Slot x 2
3 Tablet Holder Arm
4 Tablet Stand
Cable Management
5
Holes
3
4
1
• Holds a single Tablet
• Allows for 360° of rotation
• Deters theft
• Insert (up to) two K-Slot Style Laptop Locks (one
included, one sold separately)
• Part of the Tablet Holder
• Three points of contact with the Tablet
• Integrated Spacers to prevent Tablet scratches
• (Optional) Spacers can be inserted into the Tablet
Holder Arms for thin Tablets
• Holds the Tablet Holder
• Allows for 180° of tilt
• Route the Tablet Charging Cable and K-Slot
Style Laptop Lock Cables through the Tablet
Stand
Requirements
For the latest requirements, please visit:
www.startech.com/SECTBLTDT
• Tablet
• Size: 7.9 - 13 Inch (200.66 - 330.2 mm)
• Thickness (Maximum): 0.374 Inches (9.5 mm)
• (Optional -- for mounting) Electric Drill
• (Optional -- for mounting) Writing Utensil (i.e. Pencil, Pen, etc.)
• Phillips Head Screwdriver
Installation
2
5
*Tablet sold separately.
Congure the Tablet Holder
Tablet Holder Arm
(Top)
Tab
(Top)
Figure 1
(Bottom)
Tablet Holder
Arm (Bottom)
Figure 3 Figure 4
Upper Hole
Lower Hole
Pivot Point
Figure 2
Tab
M4 Screw
1. Pull and hold the top Tab and extend the top Tablet Holder Arm until it reaches its
full length. (Figure 1)
2. Fold out the two lower Tablet Holder Arms.
3. (Optional -- for thin Tablets) Peel and stick the three Spacers over the existing
Screen Protection Pads located within the tips of all three Tablet Holder Arms.
Install the Tablet Holder
1. While the Table Holder Arm (Top) is fully extended, align the hole in the Tablet
Holder with the Pivot Point on the Tablet Stand. Continue to hold the Tablet
Holder. (Figure 2)
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: November 11, 2020
For Tablet sizes of 7.9 - 10 Inches (200.66 - 254 mm), use the Lower Hole.
--Or--
For Tablet sizes of 10.1 - 13 Inches (256.54 - 330.2 mm), use the Upper Hole.
2. Insert the M4 Screw through the Tablet Holder, the Washer, and into the Pivot
Point on the Tablet Stand.
3. Tighten the M4 Screw, using a Phillips Head Screwdriver.
4. For Tablet sizes of 7.9 - 10 Inches (200.66 - 254 mm), slide and hold the Tab on one
of the bottom Tablet Holder Arms while pushing the Tablet Holder Arm inwards to
collapse the Tablet Holder Arm, then release the Tab. (Figure 3)
--Or--
For Tablet sizes of 10.1 - 13 Inches (256.54 - 330.2 mm), slide and hold the Tab on one
of the bottom Tablet Holder Arms while pulling the Tablet Holder Arm outwards to
extend the Tablet Holder Arm, then release the Tab. (Figure 4)
5. Repeat step 7 for the second bottom Tablet Holder Arm.
2. Route the K-Slot Style Laptop Lock Cable through one of the Cable Management
Holes in the rear of the Tablet Stand.
3. Insert the K-Slot Style Laptop Lock into one of the Lock Slots in the rear of the
Secure Articulating Universal Tablet Mount.
4. (Optional -- for Mounting Surfaces made of wood) Place the Tablet Mount
Assembly onto the desired Mounting Surface and mark the location of the four
Screw Holes in the Tablet Stand with a Writing Utensil.
5. Remove the Tablet Mount Assembly and drill four 2.5 mm Pilot Holes into the
marked locations on the Mounting Surface, using an Electric Drill.
6. Place the Tablet Mount Assembly back onto the desired Mounting Surface and
align the four Holes in the Tablet Stand with the four Pilot Holes in the Mounting
Surface.
7. Insert the four 3x12 mm Screws through the Tablet Stand and into the Tablet
Surface.
8. Tighten the 3x12 mm Screws, using a Phillips Head Screwdriver.
Insert the Tablet into the Tablet Holder
Tablet Holder Arm
(Top)
Figure 5 Figure 6
1. Insert the Tablet into the Tablet Holder Arms, bottom-end rst. (Figure 5)
2. Press the top Tablet Holder Arm down until it is seated against the top of the Tablet.
(Figure 6)
Secure the Tablet and Mount
K-Slot Style
Laptop Lock
Cable
Management
Hole
Figure 7
1. Wrap the looped end of the K-Slot Style Laptop Lock around the Mounting Point
(e.g. table leg, xed desk mounting point, etc.) and feed the lock head of the K-Slot
Style Laptop Lock through the looped end. (Figure 7)
Lock Slot
Operation
Note: Ensure the Cables are not tangled before completing all adjustments.
Adjust the Tilt
Place one hand on the top edge of the Tablet and the
other hand on the bottom edge of the Tablet. Apply
light pressure to tilt the Tablet either upwards or
downwards. (Figure 8)
Adjust the Rotation
• Place one hand on the left side of the Tablet and
the other hand on the right side of the Tablet. Apply
light pressure to rotate the Tablet into a portrait or
landscape view.
Warning Statements
Make sure that you assemble this product according to the instructions.
This product is intended for indoor use only and should not be used outdoors.
Pinch hazard! Ensure ngers are not placed along any of the moving parts when making adjustments.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of thirdparty companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of the Phillips Screw Company in the United States and other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
Figure 8
Loading...