Star Manufacturing GX10ISG, GX14IG, GX14IS, GX14ISG, GX20IG Operation Manual

TWO SIDED

GRILLS

MODEL

GX10IG, IS, ISG
GX14IG, IS, ISG
GX20IG, IS, IGS

Installation and

Operation

Instructions

2M-Z7971 Rev. J 9/22/2010

GX10IG

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business

8:00 am to 4:30 p.m. Central Standard Time

Hours:
Telephone: [phone] Local [phone]
Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

GENERAL INSTALLATION DATA

This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor
for use directly by the general public in food service locations.

CAUTION

All shipping containers should be checked for freight damage both visible and concealed.
This unit has been tested and carefully packaged to insure delivery of your unit in perfect
condition. If equipment is received in damaged condition, either apparent or concealed, a
claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is
unpacked, a request for inspection of concealed damage must be made with carrier within
15 days. Be certain to retain all contents plus external and internal packaging materials for
inspection. The carrier will make an inspection and will supply necessary claim forms.

VENTILATION AND CLEARANCES

The installation of any components such as a vent hood, grease extractors, and/or re

extinguishing systems, must conform to their applicable nationally recognized installation
standards and/or local building codes.

ELECTRICAL CONNECTION

Before making any electrical connection be sure to read data plate which is located at the
bottom of the unit.

ELECTRICAL GROUNDING INSTRUCTIONS

This unit is equipped with a 3-prong (grounding) plug for your protection against shock
hazard and must be plugged directly into a properly grounded 3-prong receptacle.

WARNING

DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM THE
PLUG.

CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE
DATA PLATE OF THE UNIT.

3

ELECTRICAL SPECIFICATIONS

Model

GX10IG 120V 1,400 11.7 NEMA 5-15P
GX10IG 230V 1,650 7.2 BS 1363A (16amp)
GX10IG 208/240V 1,350 / 1,800 6.5 / 7.5 NEMA 6-15P
GX10IS 120V 1,400 11.7 NEMA 5-15P
GX10IS 230V 1,650 7.2 BS 1363A (16amp)
GX10IS 208/240V 1,350 / 1,800 6.5 / 7.5 NEMA 6-15P
GX10ISG 120V 1,400 11.7 NEMA 5-15P
GX10ISG 230V 1,650 7.2 BS 1363A (16amp)

GX14IG 120V 1,800 15 NEMA 5-15P
GX14IG 230V 2,570 11.2 BS 1363A (16 amp)
GX14IG 208/240V 2,100 / 2,800 10.1 / 11.7 NEMA 6-15P
GX14IS 120V 1,800 15 NEMA 5-15P
GX14IS 230V 2,570 11.2 BS 1363A (16 amp)
GX14IS 208/240V 2,100 / 2,800 10.1 / 11.7 NEMA 6-15P
GX14ISG 120V 1,800 15 NEMA 5-15P
GX14ISG 230V 2,570 11.2 BS 1363A (16 amp)

GX20IG 208/240V 2,700 / 3,600 13 / 15 NEMA 6-20P
GX20IG 230V 3,300 14.4 BS 1363A (16 amp)
GX20IGS 208/240V 2,700 / 3,600 13 / 15 NEMA 6-20P
GX20IGS 230V 3,300 14.4 BS 1363A (16 amp)
GX20IS 208/240V 2,700 / 3,600 13 / 15 NEMA 6-20P
GX20IS 230V 3,300 14.4 BS 1363A (16 amp)

Voltage Rated Wattage Amps Plug

WARNING

CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE
DATA PLATE OF THE UNIT.

INITIAL START UP

Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).

Before using the unit for the rst time, wipe down the exterior and grilling area with a damp

cloth. Take to a well ventilated area and heat for approximately 30 minutes. The grill may
emit a small amount of smoke as the cooking surfaces reaches 450°F. Do not be alarmed,
as the smoke is caused by oils associated with the manufacturing process and will stop when
the burn off is complete. Brush off any debris from the grilling surface.

SEASONING THE COOKING SURFACES

The cooking surfaces must be "seasoned" in order to reduce product sticking. To season,
bring grill to 300°F, until completed. Brush upper and lower cooking surfaces with a a salt

free liquid vegitable oil. If using an aerosol agent, rst apply into a cup and then brush onto

cooking surface. Let sit for 20 minutes, and then wipe clean using a warm damp cloth.
Repeat if required.

SETTING THE TEMPERATURE

The thermostat control knob is used to set the temperature to your requirements. The
maximum set point is 450°F (232°C), the minimum set point
is 175°F (79°C). See Knob Settings.

DAILY OPERATION

Check the power cord to insure that it is plugged into a proper outlet.
Check that the thermostat control is turned on.

The pilot light will come on when the thermostat control goes past the 175°F.
Set the thermostat control knob to desired temperature.
Always allow 20 minutes of preheat time before loading the unit with product.

Failure to allow sufcient preheat time will result in unsatisfactory cooking of the rst load.

4

OPERATING HINTS AND SAFETY

Disconnect power to the unit with the switch at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Turn thermostat down to 200°F (93°C) during idle periods. It will take only a few minutes to

regain operating temperature.
Use spatula to push excess grease into grease cup after each load of food is cooked.

This will reduce smoking of hot grease and carbonizing.
Do not leave the unit at high temperature when not in use or during idle periods.

This will cause food particles and grease lm to carbonize.

"Season" cooking surfaces with non-salted vegetable oil to reduce product sticking.

MONTHLY LUBRICATION/INSPECTION

Apply two (2) drops of non-toxic mineral or vegetable oil to
hinge bracket at the rear.

Check the bolts, screws and nuts, tighten if necessary.

Abobe: Oiling the Hinge,

Below: Tightening the top housing

TOP HOUSING MAINTENANCE

The Spring setting which holds the top housing in the up position is
set at the factory and should provide many years of use without the
need of adjusting. After a extended period of time the top housing
may not maintain its original setting, therefore the spring tension can
be adjusted by tightening and loosening the Retainer bolts on the

back of the unit.

CAUTION

CLEANING

While holding top lid with one hand, apply only cleaners which are safe for aluminum and
iron surfaces. Wipe with clean sponge or towel until unit is clean.

1. If particles adhere to the cooking surface during the day, scrape them off with a spatula
or stiff brush.

NOTE: It is best not to let food cook on to the grill, as build up of food on the grill will increase
sticking and smoking. In addition, carbon may build up on the grill surface and reduce the

cooking efciency.

2.

At the end of the day, wipe down all surfaces with a warm, damp cloth, use a mild

detergent on all non-cooking areas and then dry entire unit.

3.

Remove and empty to clean grease catcher cup as required using mild detergent and

water

.

CLEANING CARBON BUILDUP

1. When carbon build up occurs, use a carbon removal agent to clean cooking surface. When
this process is completed, you must re-season the grill (See Seasoning Grill).

2. Acidic cleaners are NOT recommended as a cleaning agent.
CLEANING TOOLS

DO NOT IMMERSE OR LET THE UNIT STAND IN WATER.
DO NOT HOSE DOWN THE UNIT OR THE TABLE/COUNTER IF THE UNIT IS ON

5